HA Headed Anchor For welding to fillet or heel of angle consult SWA representative for ferrule part number. STUD SPECIFICATIONS D A 1 /4 /8 1 /2 5 /8 .187 .281 .281 .312 3 Description 1 1 /4 x 11/8 11 /4 x 2 /16 1 3 3 3 3 3 3 3 1 / x4/ 4 8 3 /8 x 1 /8 5 /8 x 1 /8 1 /8 x 2 /8 5 /8 x 2 /8 1 /8 x 3 /8 1 /8 x 4 /8 1 / x6/ 8 8 Part Number 18 HA0250112 65 69 75 93 108 126 155 218 H .500 .750 1.000 1.250 Weight (lbs.) Per 1000 43 FERRULE SPECIFICATIONS No. D B F M FF-025 FF-037 FF-050 FF-062 .454 .640 .795 1.030 .380 .505 .650 .785 Pieces Per Weight (lbs.) Standard Box Description Per 1000 HA0250268 HA0250412 HA0370137 HA0370162 HA0370212 HA0370262 HA0370312 HA0370412 HA0370612 2000 1 1000 1 /2 x 2 /8 1000 1 / x2/ 1 / x3/ Part Number Pieces Per Standard Box 130 HA0500162 500 170 HA0500212 500 8 197 HA0500262 500 8 226 HA0500312 250 5 /2 x 3 /8 259 HA0500362 250 1 292 HA0500412 250 5 2 2 5 1 1000 1000 1 1000 1 /2 x 5 /16 341 HA0500531 200 500 1 1 393 HA0500612 150 500 1 1 504 HA0500812 100 500 1 250 5 5 5 5 5 LENGTH: Length is before weld. Stud diameters (D) /2 and below will be approximately 1/8 shorter af ter welding. 5/8 will be approximately 3/16 shorter af ter welding. /2 x 6 /8 /2 x 8 /8 1 630 HA0501012 75 16 315 HA0620268 250 16 360 HA0620318 200 3 /8 x 4 /16 450 HA0620418 200 3 560 HA0620518 150 9 652 HA0620656 100 3 793 HA0620818 100 1039 HA0621018 75 11 / x2 / 5 1 /2 x 4 /8 /2 x 10 /8 5 HEADED ANCHOR STUDS are designed for welding to flat surfaces or welding in the fillet or to the heel of angles. When ordering specif y if studs are to be welded to flat surfaces or in fillet or to heel of angle. All orders for studs include required ferrules. STAINLESS STEELS: HA studs are also available in stainless steel. 1 .390 .390 .438 .516 1 All S.W.A. headed anchors meet AWS specifications. Test reports available on request. MATERIAL: Low carbon steel. ASTM A108 / 2 x 15 / 8 .234 .234 .250 .328 8 3 / x3/ 8 /8 x 5 /16 /8 x 6 /16 /8 x 8 /16 3 /8 x 10 /16 Mechanical Property Requirements Tensile strength Yield strength (0.2% of fset) Elongation (% in 2 in.) Reduction of area 1 2 Type A1 55,000 psi min (380 MPa) 17% min 50% min Type B2 60,000 psi min (415 MPa) 50,000 psi min (345 MPa) 20% min 50% min Type A studs shall be general purpose of any type and size used for purposes other than shear transfer in composite beam design and construction. Type B studs shall be studs that are heated, bent, or of other configuration in 1/2 in. (12.7 mm), 5/8 in. (15.9 mm), 3/4 in. (19mm), 7/8 in. (22.2 mm) and 1 in. (25.4 mm) diameter that are used as an essential component in composite beam design and construction. STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 50 SC Shear Connector Stud For welding to fillet or heel of angle consult SWA representative for ferrule part number. 3 Stud Specifications D H 3 11/4 /4 A 3 /8 Ferrule Specifications Type 33/16 3 3 /8 7 3/ 8 4/ 16 3 4 /8 7 4 /8 3 5 /16 3 5 /8 7 No. D B F 1.215 1.030 .469 .656 Weld Through Deck FW-075 1.325 1.210 .406 .600 509 572 611 640 707 736 759 /8 A 13/8 SC0750318 125 33/16 125 11 100 100 SC0750337 SC0750387 SC0750418 SC0750437 SC0750487 SC0750518 SC0750537 3 /8 Ferrule Specifications Type No. D B Flat Surface FF-087 1.408 1.210 .545 .732 640 SC0870318 100 3 /16 726 SC0870368 100 3 4/ 811 SC0870418 75 3 5/ 981 SC0870518 60 100 3 6 /16 1153 SC0870618 60 75 3 7 /16 1322 SC0870718 50 60 3 8 /16 1473 SC0870818 45 60 3 1642 SC0870918 40 1800 SC0871018 40 60 6 /18 861 SC0750618 60 3 7/ 987 SC0870718 50 3 1112 SC0750818 60 All S.W.A. shear connector studs meet AWS specifications. Test reports available on request. SHEAR CONNECTOR STUDS are designed to ef fectively tie the concrete to the steel beams and to resist shear loadings between the concrete slab and steel beam in composite construction. All orders for studs include required ferrules. LENGTH: Length is before weld. Studs when welded to base metal will be approximately 3/16 shorter af ter weld and when welded thru-deck 3/8 shorter af ter weld. Lengths for shear connector studs are generally set by governing specifications. Consult your SWA representative for other lengths available for specific applications. MATERIAL: Low carbon steel. STAINLESS STEELS: SC studs are also available in stainless steel. 16 16 9 /16 3 10 /16 Mechanical Property Requirements Tensile strength Yield strength (0.2% of fset) Elongation % in 2 in. Reduction of area 1 2 Type A1 Type B2 55,000 psi min (380 MPa) 60,000 psi min (415 MPa) 50,000 psi min (345 MPa) 17% min 20% min 50% min 50% min Type A studs shall be general purpose of any type and size used for purposes other than shear transfer in composite beam design and construction. Type B studs shall be studs that are heated, bent, or of other configuration in 1/2 in. (12.7 mm), 5/8 in. (15.9 mm), 3/4 in. (19mm), 7/8 in. (22.2 mm) and 1 in. (25.4 mm) diameter that are used as an essential component in composite beam design and construction. STUD WELDING PRODUCTS, INC. 51 M Pieces Per Standard Box SC0750587 Standard Weight (lbs) Length Per 1000 F Part Number 832 8/ 7 H Pieces Per Standard Box 3 16 D Part Number 5 /8 16 M FF-075 486 /8 DIAMETER SHEAR CONNECTORS Stud Specifications Flat Surface Standard Weight (lbs) Length Per 1000 3 7 /4 DIAMETER SHEAR CONNECTORS Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com Shear Connector Stud SC For welding to fillet or heel of angle consult SWA representative for ferrule part number. 1 DIAMETER SHEAR CONNECTORS Stud Specifications D H 1 15/8 A 1 /2 Ferrule Specifications Type No. Flat Surface FF-100 Standard Weight (lbs) Length Per 1000 D B Mechanical Property Requirements F M 1.625 1.416 .633 .835 Par t Number Pieces Per Standard Box 41/4 1133 SC1000425 75 51/4 1383 SC1000525 60 61/4 1600 SC1000625 60 81/4 2050 SC1000825 40 91/4 2225 SC1000925 40 Tensile strength Yield strength (0.2% of fset) Elongation % in 2 in. Reduction of area 1 2 Type A1 Type B2 55,000 psi min (380 MPa) 60,000 psi min (415 MPa) 50,000 psi min (345 MPa) 17% min 20% min 50% min 50% min Type A studs shall be general purpose of any type and size used for purposes other than shear transfer in composite beam design and construction. Type B studs shall be studs that are heated, bent, or of other configuration in 1/2 in. (12.7 mm), 5/8 in. (15.9 mm), 3/4 in. (19mm), 7/8 in. (22.2 mm) and 1 in. (25.4 mm) diameter that are used as an essential component in composite beam design and construction. SHEAR CONNECTOR STUDS are designed to ef fectively tie the concrete to the steel beams and to resist shear loadings between the concrete slab and steel beam in composite construction. All orders for studs include required ferrules. LENGTH: Length is before weld. Studs will be approximately 1 /4 shorter af ter welding. Lengths for shear connector studs are generally set by governing specifications. Consult your SWA representative for other lengths available for specific applications. MATERIAL: Low carbon steel. STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 52 DA Deformed Anchor STUD SPECIFICATIONS Parts No. DA0250612 DA0251212 DA0371012 DA0371212 DA0371812 DA0372412 DA0373012 DA0373612 DA0501012 DA0501212 DA0501812 DA0502412 DA0503012 DA0503612 DA0621218 DA0621818 DA0622418 DA0623018 DA0623618 DA0751218 DA0751818 DA0752418 DA0753018 DA0753618 Description 1 /4 x 61/8 1 /4 x 121/8 3 /8 x 101/8 3 /8 x 121/8 3 /8 x 181/8 3 /8 x 241/8 3 /8 x 301/8 3 /8 x 361/8 1 /2 x 101/8 1 /2 x 121/8 1 /2 x 181/8 1 /2 x 241/8 1 /2 x 301/8 1 /2 x 361/8 5 /8 x 12 3/16 5 /8 x 183/16 5 /8 x 243/16 5 /8 x 303/16 5 /8 x 363/16 3 /4 x 123/16 3 /4 x 183/16 3 /4 x 243/16 3 /4 x 303/16 3 /4 x 363/16 Weight (lbs) Per 1000 88 175 288 344 365 685 855 1026 545 680 972 1292 1615 1935 1077 1633 2136 2666 3196 1525 2276 3027 3778 4529 FERRULE SPECIFICATIONS Pieces Per Standard Box 1000 1000 1000 1000 700 700 700 700 700 700 350 350 350 350 500 250 250 250 250 250 125 125 125 125 D No. B D G M 1 FF-025 .380 .455 .234 .390 3 FF-037 .505 .640 .234 .390 1 FF-050 .650 .795 .250 .438 5 FF-062 .785 1.030 .328 .516 3 FF-075 1.215 1.030 .469 .656 /4 /8 /2 /8 /4 Mechanical Property Requirements MATERIAL: Low Carbon Steel ASTM: A-496 LENGTH: Length is before weld. Stud diameters (D) 1/2 and smaller will be approximately 1/8 shorter af ter welding. 5/8 and larger will be approximately 3/16 shorter af ter welding. Type C3 3 Tensile strength Yield strength (0.2% of fset) 80,000 psi min (552 MPa) (0.5% of fset) 70,000 psi min (485 MPa) Elongation % in 2 in. Reduction of area Type C studs are cold-worked deformed steel bars manufactured in accordance with specification ASTM A496 having a nominal diameter equivalent to the diameter of a plain wire having the same weight per foot as the deformed wire. ASTM A496 specifies a ma ximum diameter of 0.628 in. (16 mm) ma ximum. Any bar supplied above that diameter must have the same physical characteristics regarding deformations as required by ASTM A496. STUD WELDING PRODUCTS, INC. 53 Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com Partial Thread Stud PT STUD SPECIFICATIONS FERRULE SPECIFICATIONS Fillet Dimension D 1 Min. L. /4-20 3 /16-18 43 3 7 5 C A E F /8 5 3 No. /32 FP-025 /8 13 7 /64 7 B G M .455 .385 .125 .250 FP-031 .535 .445 .125 .250 /64 FP-037 .590 .505 .139 .26 .215 .275 3 /8-16 27 .330 3 /8 15 /16-14 15 .387 7 /16 17 1 /8 FP-043 .675 .585 .173 .329 /2 19 /32 5 /32 FP-050 .740 .650 .206 .362 /8 3 /4 3 /16 FP-062 .910 .785 .277 .433 /64 59 /64 1 /4 FP-075 1.150 1.030 .339 .526 3 /16 FP-087 1.330 1.210 .406 .593 FP-100 1.526 1.406 .474 .661 /8 /64 /32 /16 /32 /32 /32 /2-13 1 /32 .448 1 5 /8-11 113/64 .562 5 .680 51 /8-9 39 1 /64 .798 55 1 /64 5 1-8 151/64 .915 59 13/16 11 3 /4-10 1 /16 1 7 D 3 7 1 /16 /64 /64 HOW TO ORDER Specif y diameter, thread size before weld (BW) length, type of material. EX AMPLE 1/2-13 x 1-1/8 (BW) partial thread (PT), mild steel. /32 HOW TO DETERMINE BEFORE WELD (BW) LENGTH First establish the standing length of the stud af ter weld (AW). Based on the diameter of the stud include the following additional length before weld (BW). Diameters up through 9/16 add 1/8 Diameters from 5/8 through 7/8 add 3/16 Diameters 1 through 1-1/4 add 1/4 STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 54 FT Full Thread Stud STUD SPECIFICATIONS D Min. L. 10-24 25 1 /4-20 25 5 /16-18 25 3 /8-16 25 7 /16-14 25 1 13 5 31 /2-13 /8-11 3 /4-10 7 /8-9 1-8 /32 /32 /32 /32 /32 /16 /32 15 1 /64 1 1 /2 17 1 /32 C FERRULE SPECIFICATIONS Fillet Dimension No. D B G M .187 9 3 FF-019 .390 .305 .234 .390 .187 23 /64 7 FF-025 .454 .380 .234 .390 .187 7 /16 7 FF-031 .578 .445 .234 .390 .187 1 /2 1 /8 FF-037 .640 .505 .234 .390 .187 37 /64 9 /64 FF-043 .703 .585 .234 .422 .187 11 /16 5 FF-050 .795 .650 .250 .438 .187 51 /64 3 /16 FF-062 1.030 .785 .328 .516 .187 15 /16 1 /4 FF-075 1.215 1.030 .469 .656 .375 3 5 /16 FF-087 1.408 1.210 .545 .732 15 3 FF-100 1.615 1.406 .633 .820 .375 E /32 1 /32 1 /64 HOW TO ORDER Specif y diameter, thread size before weld (BW) length, type of material. EX AMPLE 1/2-13 x 1-1/8 (BW) Full Thread (FT), mild steel. F /32 /64 /64 /32 /8 HOW TO DETERMINE BEFORE WELD (BW) LENGTH First establish the standing length of the stud af ter weld (AW). Based on the diameter of the stud include the following additional length before weld (BW). Diameters up through 9/16 add 1/8 Diameters from 5/8 through 7/8 add 3/16 Diameters 1 through 1-1/4 add 1/4 STUD WELDING PRODUCTS, INC. 55 Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com RB Reduced Base Stud STUD SPECIFICATIONS D 1 5 3 1 Min. L. C A FERRULE SPECIFICATIONS Fillet Dimension E F No. D B G M FM-025 .455 .380 .265 .390 /4-20 3 /4 .187 .187 5 /16-18 3 .272 .187 13 7 /64 FF-031-X .578 .445 .281 .437 /8-16 3 .375 15 7 /64 FM-037 .590 .505 .125 .250 /32 1 /8 FM-050 .740 .650 .125 .281 /32 .875 .785 .174 .328 /2-13 /4 /4 .312 /16 /32 /32 1 .437 .437 17 3 /32 5 /8-11 11/ 4 .500 .547 19 5 /32 FM-062 3 /4-10 11/2 .620 .797 3 3 /16 FF-062 1.030 .785 .328 .516 11/2 .745 .922 59 /64 1 /4 FF-075 1.215 1.030 .469 .656 13/4 .875 1.078 13/64 5 /16 FF-087 1.408 1.210 .545 .732 7 / 8- 9 1-8 /4 HOW TO ORDER Specif y diameter, thread size before weld (BW) length, type of material. EX AMPLE 3/8-16 x 1 (BW) reduce base (RB), mild steel. HOW TO DETERMINE BEFORE WELD (BW) LENGTH First establish the standing length of the stud af ter weld (AW). Based on the diameter of the stud include the following additional length before weld (BW). Diameters up through 9/16 add 1/8 Diameters from 5/8 through 7/8 add 3/16 Diameters 1 through 1-1/4 add 1/4 STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 56 Collar Studs CK How To Order: Specif y base diameter, before weld (BW) length to the top of the collar, thread size and length, type of material. Example: .330 x 1-1/2"(BW) with a 3/8-16 x 3/4" thread ex tension, collar stud (CK), mild steel. STUD SPECIFICATIONS D Std. B Min. L. 1 /4-20 5 3 5 /16-18 5 3 3 5 3 1 3 1 /8-16 /2-13 /8 /8 /8 /8 /8 /8 /4 /2 C FERRULE SPECIFICATIONS E H No. D B G M .214 1 3 FK-025 .875 .785 .110 .235 .273 5 3 FK-031 .875 .785 .095 .235 .331 5 3 FK-037 .875 .785 .095 .235 .446 3 3 FK-050 1.030 .921 .125 .250 SB /2 /8 /8 /4 /32 /32 /32 /32 Shoulder Studs How To Order: Specif y base diameter, before weld (BW) length of the base, thread size and length, type of material. Example: 1 /2" base diameter, 1-1/8" before weld (BW) length, with a 3/8-16" x 3/4" thread ex tension (SB), stainless steel. STUD SPECIFICATIONS D Std. B Min. L. C FERRULE SPECIFICATIONS E H No. D B G M .214 1 3 FK-025 .875 .785 .110 .235 3 FK-031 .875 .785 .095 .235 1 /4-20 5 3 5 /16-18 5 3 .273 5 3 5 3 .331 5 3 FK-037 .875 .785 .095 .235 1 3 1 .446 3 3 FK-050 1.030 .921 .125 .250 /8-16 /2-13 /8 /8 /8 /4 /8 /8 /8 /2 /2 /8 /8 /4 /32 /32 /32 /32 STUD WELDING PRODUCTS, INC. 57 Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com NT No Thread Stud STUD SPECIFICATIONS FERRULE SPECIFICATIONS Fillet Dimension D Min. L E /16 25 9 1 /4 25 23 5 /16 25 7 3 /8 25 1 /16 25 19 1 /2 13 11 5 /8 31 7 3 /4 115/64 7 /8 3 7 1 B G M .390 .305 .234 .390 FF-025 .455 .385 .234 .390 /64 FF-031 .578 .445 .234 .390 1 /8 FF-037 .640 .505 .234 .390 9 /64 FF-043 .703 .585 .234 .422 5 /32 FF-050 .795 .650 .250 .438 3 /16 FF-062 1.030 .785 .328 .516 11/64 1 /4 FF-075 1.215 1.030 .469 .656 11/2 11/8 5 /16 FF-087 1.408 1.210 .545 .732 41 3 3 FF-100 1.610 1.406 .633 .820 /32 /32 F No. D /32 FF-019 7 /64 /16 7 /2 /32 /64 /32 /32 /32 /32 /16 /16 /32 1 /64 /8 1 /8 3 /8 HOW TO ORDER Specif y base diameter, before weld (BW) length, tap size and depth, type of material. EX AMPLE 3/8 x 1-1/2 (BW) No Thread (NT), stainless steel. HOW TO DETERMINE BEFORE WELD (BW) LENGTH First establish the standing length of the stud af ter weld (AW). Based on the diameter of the stud include the following additional length before weld (BW). Diameters up through 9/16 add 1/8 Diameters from 5/8 through 7/8 add 3/16 Diameters 1 through 1-1/4 add 1/4 STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 58 TS Tapped Stud STUD SPECIFICATIONS Tap C B 8- 32 1 10-24 9 1 3 / - 20 5 4 7 D=1/2 Max. /4 9 / 21 32 / 8 /16 / 13 / 32 16 5 D= 3 /8 to /4 5 /8 22 7 / 32 / 8 15 /32 29 31 /8- 16 9 /16 1 7 /16-14 21 /32 1 /32 /2- 13 3 /4 3 /8- 11 15 /16-18 3 1 5 3 / - 10 4 FERRULE SPECIFICATIONS Minimum Length /16 /32 1 /32 /32 1 /64 9 1 /8 5 1 /8 D=7/8 Over Fillet Dimension STUD DIA. E 11 23 /64 7 25 7 / 7 /16 / 15 / 32 1 16 / 2 D /64 1 / 5 1 1 19 9 5 11 /16 5 11 7 /8 3 7 1 11 64 / 8 No. J K G M /8 FF-025 .455 .380 .234 .390 / 3 FF-031 .578 .445 .234 .390 8 FF-037 .640 .505 .234 .390 16 / /64 7 /16 FF-043 .703 .585 .234 .422 /32 1 /2 FF-050 .795 .650 .250 .438 /16 5 /8 FF-062 1.030 .785 .328 .516 1 /16 1 /4 3 /4 FF-075 1.215 1.030 .469 .656 1 /16 1 1 /8 5 /16 7 /8 FF-087 1.408 1.210 .545 .732 2 3 3 1 FF-100 1.610 1.406 .633 .820 1 /32 /32 1 /32 1 /32 1 /16 1.125 1/ HOW TO ORDER Specif y base diameter, finished length before weld (BW) length, tap size, tap depth and type of material. EX AMPLE 16 F 5/8 x 1-1/4 (BW) Tapped Stud (TS) with a 3/8-16 x 7/16 tap, mild steel. 8 / 8 HOW TO DETERMINE BEFORE WELD (BW) LENGTH First establish the standing length of the stud af ter weld (AW). Based on the diameter of the stud include the following additional length before weld (BW). Diameters up through 9/16 add 1/8 Diameters from 5/8 through 7/8 add 3/16 Diameters 1 through 1-1/4 add 1/4 STUD WELDING PRODUCTS, INC. 59 Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com PARTIAL THREAD STAINLESS STEEL STUDS Before Weld (BW) STAINLESS STEEL Partial Thread DESCRIPTION PART # 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 PDBSS25X087 PDBSS25X100 PDBSS25X112 PDBSS25X125 PDBSS25X138 PDBSS25X150 PDBSS25X162 PDBSS25X175 PDBSS25X200 PDBSS25X212 PDBSS25X338 X X X X X X X X X X X 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-3/4 2 2-1/8 3-3/8 X X X X X X X X X X X X X X X X X X X X X 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-3/4 2 3 4 7/8 1 1-1/8 1-3/8 1-1/2 1-5/8 1-3/4 2 2-1/8 2-1/4 PDBSS312X087 PDBSS312X100 PDBSS312X112 PDBSS312X125 PDBSS312X138 PDBSS312X150 PDBSS312X162 PDBSS312X175 PDBSS312X200 PDBSS312X300 PDBSS312X400 PDBSS38X087 PDBSS38X100 PDBSS38X112 PDBSS38X138 PDBSS38X150 PDBSS38X162 PDBSS38X175 PDBSS38X200 PDBSS38X212 PDBSS38X225 DESCRIPTION PART # DESCRIPTION PART # 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 X X X X X X X X X X X 2-3/8 2-1/2 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/2 4 5 6 PDBSS38X238 PDBSS38X250 PDBSS38X262 PDBSS38X275 PDBSS38X287 PDBSS38X300 PDBSS38X312 PDBSS38X350 PDBSS38X400 PDBSS38X500 PDBSS38X600 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 X X X X X X X X X X X X X X X X X X X X X X X 1 1-1/8 1-1/2 1-5/8 1-3/4 1-7/8 2 2-1/8 2-1/4 2-3/8 2-1/2 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/4 3-1/2 3-3/4 4 4-1/2 5 6 PDBSS50X100 PDBSS50X112 PDBSS50X150 PDBSS50X162 PDBSS50X175 PDBSS50X187 PDBSS50X200 PDBSS50X212 PDBSS50X225 PDBSS50X238 PDBSS50X250 PDBSS50X262 PDBSS50X275 PDBSS50X287 PDBSS50X300 PDBSS50X312 PDBSS50X325 PDBSS50X350 PDBSS50X375 PDBSS50X400 PDBSS50X450 PDBSS50X500 PDBSS50X600 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 X X X X X X X X X X X X X X X X X 1-1/4 1-1/2 1-5/8 1-3/4 1-7/8 2 2-1/8 2-1/4 2-1/2 2-5/8 2-3/4 3 3-1/8 3-1/2 4 5 6 PDBSS62X125 PDBSS62X150 PDBSS62X162 PDBSS62X175 PDBSS62X187 PDBSS62X200 PDBSS62X212 PDBSS62X225 PDBSS62X250 PDBSS62X262 PDBSS62X275 PDBSS62X300 PDBSS62X312 PDBSS62X350 PDBSS62X400 PDBSS62X500 PDBSS62X600 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 X X X X X X X X X X X X X 1-1/2 1-3/4 2 2-1/8 2-1/4 2-1/2 2-3/4 3 3-1/2 4 4-1/2 5 6 PDBSS75X150 PDBSS75X175 PDBSS75X200 PDBSS75X212 PDBSS75X225 PDBSS75X250 PDBSS75X275 PDBSS75X300 PDBSS75X350 PDBSS75X400 PDBSS75X450 PDBSS75X500 PDBSS75X600 STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 60 FULL THREAD STAINLESS STEEL STUDS Before Weld (BW) STAINLESS STEEL Full Thread DESCRIPTION PART # 10-24 10-24 10-24 10-32 10-32 X X X X X 3/4 7/8 1 3/4 1 PDSS1024X075 PDSS1024X087 PDSS1024X100 PDSS1032X075 PDSS1032X100 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 X X X X X X X X X X 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 2 PDSS25X062 PDSS25X075 PDSS25X087 PDSS25X100 PDSS25X112 PDSS25X125 PDSS25X138 PDSS25X150 PDSS25X162 PDSS25X200 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 X X X X X X X X 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 PDSS312X062 PDSS312X075 PDSS312X087 PDSS312X100 PDSS312X112 PDSS312X125 PDSS312X138 PDSS312X150 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 X X X X X X X X 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-3/4 PDSS38X075 PDSS38X087 PDSS38X100 PDSS38X112 PDSS38X125 PDSS38X138 PDSS38X150 PDSS38X175 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 X X X X X X X 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 PDSS50X087 PDSS50X100 PDSS50X112 PDSS50X125 PDSS50X138 PDSS50X150 PDSS50X162 STUD WELDING PRODUCTS, INC. 61 Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com PARTIAL THREAD MILD STEEL STUDS Before Weld (BW) MILD STEEL Partial Thread DESCRIPTION PART # 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 PDBMS25X087 PDBMS25X100 PDBMS25X112 PDBMS25X125 PDBMS25X138 PDBMS25X150 PDBMS25X162 PDBMS25X175 PDBMS25X200 PDBMS25X212 PDBMS25X338 X X X X X X X X X X X 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-3/4 2 2-1/8 3-3/8 X X X X X X X X X X X X X X X X X X X X X 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-3/4 2 3 4 7/8 1 1-1/8 1-3/8 1-1/2 1-5/8 1-3/4 2 2-1/8 2-1/4 PDBMS312X087 PDBMS312X100 PDBMS312X112 PDBMS312X125 PDBMS312X138 PDBMS312X150 PDBMS312X162 PDBMS312X175 PDBMS312X200 PDBMS312X300 PDBMS312X400 PDBMS38X087 PDBMS38X100 PDBMS38X112 PDBMS38X138 PDBMS38X150 PDBMS38X162 PDBMS38X175 PDBMS38X200 PDBMS38X212 PDBMS38X225 DESCRIPTION PART # DESCRIPTION PART # 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 X X X X X X X X X X X 2-3/8 2-1/2 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/2 4 5 6 PDBMS38X238 PDBMS38X250 PDBMS38X262 PDBMS38X275 PDBMS38X287 PDBMS38X300 PDBMS38X312 PDBMS38X350 PDBMS38X400 PDBMS38X500 PDBMS38X600 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 X X X X X X X X X X X X X X X X X X X X X X X 1 1-1/8 1-1/2 1-5/8 1-3/4 1-7/8 2 2-1/8 2-1/4 2-3/8 2-1/2 2-5/8 2-3/4 2-7/8 3 3-1/8 3-1/4 3-1/2 3-3/4 4 4-1/2 5 6 PDBMS50X100 PDBMS50X112 PDBMS50X150 PDBMS50X162 PDBMS50X175 PDBMS50X187 PDBMS50X200 PDBMS50X212 PDBMS50X225 PDBMS50X238 PDBMS50X250 PDBMS50X262 PDBMS50X275 PDBMS50X287 PDBMS50X300 PDBMS50X312 PDBMS50X325 PDBMS50X350 PDBMS50X375 PDBMS50X400 PDBMS50X450 PDBMS50X500 PDBMS50X600 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 5/8-11 X X X X X X X X X X X X X X X X X 1-1/4 1-1/2 1-5/8 1-3/4 1-7/8 2 2-1/8 2-1/4 2-1/2 2-5/8 2-3/4 3 3-1/8 3-1/2 4 5 6 PDBMS62X125 PDBMS62X150 PDBMS62X162 PDBMS62X175 PDBMS62X187 PDBMS62X200 PDBMS62X212 PDBMS62X225 PDBMS62X250 PDBMS62X262 PDBMS62X275 PDBMS62X300 PDBMS62X312 PDBMS62X350 PDBMS62X400 PDBMS62X500 PDBMS62X600 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 3/4-10 X X X X X X X X X X X X X 1-1/2 1-3/4 2 2-1/8 2-1/4 2-1/2 2-3/4 3 3-1/2 4 4-1/2 5 6 PDBMS75X150 PDBMS75X175 PDBMS75X200 PDBMS75X212 PDBMS75X225 PDBMS75X250 PDBMS75X275 PDBMS75X300 PDBMS75X350 PDBMS75X400 PDBMS75X450 PDBMS75X500 PDBMS75X600 STUD WELDING PRODUCTS, INC. Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com 62 FULL THREAD MILD STEEL STUDS Before Weld (BW) MILD STEEL Full Thread DESCRIPTION PART # 10-24 10-24 10-24 10-32 10-32 X X X X X 3/4 7/8 1 3/4 1 PDMS1024X075 PDMS1024X087 PDMS1024X100 PDMS1032X075 PDMS1032X100 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 1/4-20 X X X X X X X X X X 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 2 PDMS25X062 PDMS25X075 PDMS25X087 PDMS25X100 PDMS25X112 PDMS25X125 PDMS25X138 PDMS25X150 PDMS25X162 PDMS25X200 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 5/16-18 X X X X X X X X 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 PDMS312X062 PDMS312X075 PDMS312X087 PDMS312X100 PDMS312X112 PDMS312X125 PDMS312X138 PDMS312X150 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 3/8-16 X X X X X X X X 3/4 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-3/4 PDMS38X075 PDMS38X087 PDMS38X100 PDMS38X112 PDMS38X125 PDMS38X138 PDMS38X150 PDMS38X175 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 1/2-13 X X X X X X X 7/8 1 1-1/8 1-1/4 1-3/8 1-1/2 1-5/8 PDMS50X087 PDMS50X100 PDMS50X112 PDMS50X125 PDMS50X138 PDMS50X150 PDMS50X162 STUD WELDING PRODUCTS, INC. 63 Los Angeles • San Francisco • Seattle Toll Free: (800) 252-1919 • www.studweldprod.com