New X Series Centaurs
In-grade CSA Listed Wet Label IP68
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
CX 2/14
C1X
IP68
Series
C1X
Lamp
L-LED
. Cast stainless steel body 304 alloy
. 1W Cree XPE LED
. On-board electronics for 24V DC and 0-10V
dimming
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Remote power supply
. Unit can be through wired for daisy chaining
. Class II, not suitable for fountain or pool use.
. Requires remote 24V Dc power supply
. Available in RGB with remote DMX controller
In-Ground LED Fixture
Wattage
1L-1x1W 3000K LED
3L-1x1W 5000K LED
Body
4-Fully recessed
w/cond. entries
listed wet label IP68
Color Temp.
SS-Stainles Steel
Note: Other color available
Optic
Ballast
0- None
X-120vAC-24vDC
1- 6 Degree Spot
Remote Driver
2- 25 Degree Flood
Note: LED Optics are for use
with 'T' clear glass lens.
They are not intended for 'K'
or 'G' Lenes
Lens
Options
0-None
T-CLR. Temp Glass
K-Internally Ceramic Coated
Tempered Glass
G-Frosted Toughened Glass
Note: On board
0-10v Dimming
Power Supplies
SERIES
C1X
DRIVER PART #
PPLT00155
PPLT00157
PPLT00158
79 Trenton Avenue
Frenchtown, NJ 08825
DESCRIPTION
120VAC-24VDC 30W
120VAC-24VDC 60W
120VAC-24VDC 100W
Tel: (908) 996-7710
Fax: (908) 996-7042
WATTAGE
1W 24vDC w/ integral 0-10v dim
1W 24vDC w/ integral 0-10v dim
1W 24vDC w/ integral 0-10v dim
UNITS POWERED
SPECIAL DETAILS
1 to 24
1 to 48
1 to 80
parallel
parallel
parallel
Staten Island 911 Memorial
Lighting Consultant: Fisher, Marantz, Stone
Fixture: C1X
. Cast stainless steel body 304 alloy
. 1W Cree XPE LED
. On board electronics for 24V DC and 0-10V
Dimming
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Remote power supply
. Unit can be through wired for daisy chaining
. Class II, not suitable for fountain or pool use.
. Requires remote 24V Dc power supply
. Available in RGB with remote DMX controller
listed wet label IP68
C2X
In-Ground 24V Dimmable LED Fixture
IP68 Remote Driver
Series
C2X
Wattage
Body
Finish
1L-1x1W 3000K LED 4-Recessed Box w/ SS-Stainless Steel
2L-1x1W 4000K LED
Conduit Entries
4L-1x3W 3000K LED
5L-1x3W 4000K LED
Lamp
L-LED
Note: Other colors available on request
Optic
0- None
1- 10 Degree Narrow
2- 21 Degree Medium
3- 39 Degree Wide
4- 10x44 Degree Elliptical
Note: LED Optics are for use
with 'T' clear glass lens.
They are not intended for 'K'
or 'G' Lenes
Ballast
X-Remote 24vDC
Transformer
Required
Lens
T-Clear Temp Glass
K-Internally Ceramic Coated
G-Frosted Tempered Glass
Options
0-None
Note: On board
0-10v Dimming
Power Supplies
C2X
1 LED/UNIT
PPLT00155
120VAC-24VDC 30W
PPLT00157
120VAC-24VDC 60W
PPLT00158
120VAC-24VDC 100W
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
1W 24vDC w/ integral 0-10v dim
3w 24vDC w/ integral 0-10v dim
1W 24vDC w/ integral 0-10v dim
3w 24vDC w/ integral 0-10v dim
1W 24vDC w/ integral 0-10v dim
3w 24vDC w/ integral 0-10v dim
1 to 10
1 to 6
1 to 19
1 to 13
1 to 32
1 to 22
parallel
parallel
parallel
parallel
parallel
parallel
. Cast stainless steel body 304 alloy
. 1W Cree XPE LED
. On board driver for 120V
. Non dimming
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Remote power supply
. Unit can be through wired for daisy chaining
. Class II, not suitable for fountain or pool use.
listed wet label IP68
C2G
In-Ground 120V LED Fixture
IP68 Integral Driver
Series
C2G
Lamp
L-LED
Wattage
Body
1L-1x1W 3000K LED 4-Fully recessed
3L-1x1W 5000K LED w/cond. entries
Finish
SS-Stainless Steel
Note: Other colors available
on request.
Optic
0- None
1- 10 Degree Narrow
2- 21 Degree Medium
3- 39 Degree Wide
4- 10x44 Degree Elliptical
Note: LED Optics are for use
with 'T' clear glass lens.
They are not intended for 'K'
or 'G' Lenes
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
Ballast
G-Integral
Driver 120vAC
Lens
T-Clear Temp Glass
K-Internally Ceramic Coated
G-Frosted Tempered Glass
Options
0-None
. Cast stainless steel body 304 alloy
. 3x 3W Cree XPE LED
. On board electronics for 24V DC and 0-10V
dimming
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Remote power supply
. Unit can be through wired for daisy chaining
. Class II
. Requires remote power supply
listed wet label IP68
C4X
In-Ground 24V Dimmable LED
IP68 Remote Driver
Series
C4X
Lamp
L-LED
Wattage
1R-3x1W White 3000K
2R-3x1W White 4000K
3R-3x3W White 3000K
4R-3x3W White 4000K
Body
4-Recessed Box w/
conduit entries
Finish
SS-Stainless Steel
Other colors available
upon request
Optic
0- None
1- Narrow (6°)
3- Wide (25°)
4- Elliptical (6°x25°)
Ballast
Q-Remote 24vDC
Driver Required
(Int. 0-10V Dim.)
Remote Driver
to be ordered
separately
Lens
T-Clear Temp Glass
J-Flash White BTM &
Non-Skid Top Pattern
K-Flash White BTM &
Clear Top
G-Internally Frosted
Toughened Glass
Q-Non-Skid Top Patterned
Tempered Glass
Options
0-None
Power Supplies
C4X
3 LED'S PER
UNIT
PPLT00155
120VAC-24VDC 30W
PPLT00157
120VAC-24VDC 60W
PPLT00158
120VAC-24VDC 100W
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
1W 24vDC w/ integral 0-10v dim
3w 24vDC w/ integral 0-10v dim
1W 24vDC w/ integral 0-10v dim
3w 24vDC w/ integral 0-10v dim
1W 24vDC w/ integral 0-10v dim
3w 24vDC w/ integral 0-10v dim
1 to 6
1 to 2
1 to 13
1 to 5
1 to 22
1 to 8
parallel
parallel
parallel
parallel
parallel
parallel
. Cast stainless steel body 304 alloy
. 3 x1W Cree XPE LED
. On board power supply for 120-277V
. Non-dimming
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Integral power supply
. Unit can be through wired for daisy chaining
. Class II, not suitable for fountain or pool use.
. Available anti slip dot pattern glass lens
listed wet label IP68
C4G
In-Ground 120-277V LED Fixture
IP68 Integral Driver
Series
C4G
Lamp
L-LED
Wattage
1R-3x1W White 3000K
2R-3x1W White 4000K
Body
4-Recessed Box w/
conduit entries
Finish
SS-Stainless Steel
Note: Other colors available on request.
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
Optic
0- None
1- Narrow (6°)
3- Wide (25°)
4- Elliptical (6°x25°)
Ballast
C-120-277vAC Int.
Non-Dimming
Elect. Driver
Lens
T-Clear Temp Glass
J-Flash White BTM &
Non-Skid Top Pattern
K-Flash White BTM &
Clear Top
G-Internally Frosted
Toughened Glass
Q-Non-Skid Top Patterned
Tempered Glass
Options
0-None
. Cast stainless steel body 304 alloy
. Cree MCE LED
. On board 24vDC with DMX interface
individually controlled
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Remote power supply
. Unit can be through wired for daisy chaining
. Class II, not suitable for fountain or pool use
. Available anti slip dot pattern glass lens
. DMX channels are not field addressable
without specialized equipment. If addresses
are not specified, the fixture will default to
address 1 (1-red, 2-green, 3-blue, 4-white).
listed wet label IP68
C4C
In-Ground LED Fixture
IP68 Remote Integral Driver
Series
C4C
Lamp
L-LED
Wattage
3K-5W RGBW LED
4K-5W Dynamic White
Body
4-Recessed Box w/
conduit entries
Finish
SS-Stainless Steel
PPLT00155
PPLT00157
PPLT00158
79 Trenton Avenue
Frenchtown, NJ 08825
Lens
Ballast
T-Clear Temp Glass
X-Remote 24vDC
Power Supply Req'd J-Flash White BTM &
(INT DMX INTERFACE) Non-Skid Top Pattern
K-Flash White BTM &
Clear Top
Note: Integral 24vDC Driver
G-Internally Frosted
Board along with individually
Toughened Glass
controlled DMX interface
Q-Non-Skid Top Patterned
To be used with
Tempered Glass
Options
0-None
Remote Power Supply.
Power Supplies
C4C
1 CREE MCE
per unit
Optic
0- None
1- Narrow (6°)
2- Med (30°)
120VAC-24VDC30W
120VAC-24VDC 60W
120VAC-24VDC 100W
Tel: (908) 996-7710
Fax: (908) 996-7042
4.6w 24vDC w/ int. DMX interface
4.6w 24vDC w/ int. DMX interface
4.6w 24vDC w/ int. DMX interface
1 to 4
1 to 9
1 to 16
parallel
parallel
Parallel
. Cast stainless steel body 304 alloy
. 6x 1W Cree XPE LED
. Integral power supply for 120V non-dimming
. Available in MR16 12V DC halogen
with integral power supply
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at 30
mph
. Cast stainless steel 304 alloy junction box
. Silicone rubber anti siphon outlet box gasket
. Remote power supply
. Unit can be through wired for daisy chaining
. Class I
. Available anti slip dot pattern glass lens
C7X
In-Ground Fixture
Flat Trim IP68
Series
C7X
Lamp
6-Halogen
L-LED
9-HID
79 Trenton Avenue
Frenchtown, NJ 08825
Wattage
14-37W MR16 NSP10
15-37W MR16 NSP25
16-37W MR16 FL40
1F-1Wx6 Ring 3K White LED
AM-1Wx6 Ring 5K White LED
2F-1Wx6 Ring Red LED
3F-1Wx6 Ring Blue LED
4F-1Wx6 Ring Green LED
5F-1Wx6 Ring Cyan LED
6F-1Wx6 Ring Amber LED
AG-20W MH GE MR16 Spot 3000K
AH-20W MH GE MR16 Flood 3000K
Body
4-Fully Recessed
W/ Cond. Entries
listed wet label IP68
Finish
SS-Stainless Steel
Note: MR16 Lamps
mounted to adjustable
swivel bracket tilt max 15°
off vertical.
Tel: (908) 996-7710
Fax: (908) 996-7042
Grill
1- STD
Ballast
T-120V-12V Elect.
Integral Trans.
J-277V-12V Elect.
Integral Trans.
C-120V-277V Elect.
Integral Trans.
Lens
G-Internally Frosted
Toughened Glass
U-Non Skid Temp Glass
T-Clear Temp Glass
Note:
Halogen is either T or J.
LED is always C and comes
standard with 0-10V dimming.
HID metal halide is always C.
Options
0-None
. Cast stainless steel body 304 alloy
. Xicato 1300lm LED module with integral
driver for 120-277V w/ 0-10V Dimming or
. 20W MR16 MH adjustable with integral ballast
. Unique “bottle cap” threaded lens frame
. No screws to lose
. Lens frame turned from solid stainless steel
. 0.400” thick tempered glass lens
. Walkover, drive over rated for 11,000 lbs at
30 mph
. Unit can be through wired for daisy chaining
. Class I
. Available anti slip dot pattern glass lens
listed wet label IP68
CDX
In-Ground Fixture
Flat Trim IP68
Series
CDX
Lamp
9-HID
L-LED
Wattage
AG-20W MH GE MR16 Spot 3000K
AH-20W MH GE MR16 Flood 3000K
FB-39W MH GE MR16 Spot 3000K
FC-39W MH GE MR16 Flood 3000K
EX-1300lm Xicato 3000K
EY-1300lm Xicato 3500K
EZ-1300lm Xicato 4000K
Body
4-Fully Recessed
W/ Cond. Entries
Grill
1- STD
Ballast
C-120-277V Integral
Electronic
L-120-277V w/ Integral
0-10V Dimming
Ballast 'C' HID Only
Ballast 'L' LED Only
Lens
T-Clear Temp Glass
Q-Non Skid Temp Glass
Patterened
Options
0-None
W-Linear Spread
Q-Honeycomb
Louver
S-Solite Lens
B-Special Lens
(see drawing)
Note: Options
added to rubber
holder.
AG, AH, FB, FC HID Only
EX, EY, EZ LED Only
79 Trenton Avenue
Frenchtown, NJ 08825
Finish
SS-Stainless Steel
Tel: (908) 996-7710
Fax: (908) 996-7042
Drawings
C1X
C2X
Drawings
C2G
C4X
Drawings
C4G
C4C
79 Trenton Avenue
Frenchtown, NJ 08825
Tel: (908) 996-7710
Fax: (908) 996-7042
Drawings
C7X
CDX - LED
General Installation Instructions
11/2/07
FAILURE TO FOLLOW THESE INSTRUCTIONS WILL VOID WARRANTY
RISK OF ELECTRICAL SHOCK. THIS EQUIPMENT IS TO BE INSTALLED BY A QUALIFIED
ELECTRICIAN ONLY. MAKE CERTAIN ELECTRICAL SUPPLY CIRCUIT IS DE-ENERGIZED
BEFORE BEGINNING INSTALLATION. CHECK FIXTURE LABEL FOR CORRECT VOLTAGE.
READ ALL INSTRUCTIONS CAREFULLY.
LOCATION
This model is designed for concrete pour installation. The upper edge of the housing must be flush with the prepared
surface into which it is recessed. Do not install fixture in a manner that creates a pocket where water can sit on top of
fixture.
Not suitable for use in places where the luminaire is likely to be exposed to a horizontal stress load caused by braking,
acceleration or change of direction.
INSTALLATION
1. Lighting fixture comes fully assembled. Note: When not working on fixture replace trim ring for site safety and to
protect fixture components from moisture and damage. Keep each trim ring with the original body it was supplied on.
Note: Use care to protect O-ring on trim ring. Do not remove, loosen, cut, deform or otherwise disturb O -ring. Keep Oring clean and dry.
2. Set fixture in desired location. Position the fixture in such a manner that the conduit/cable is not stressed at the entry
point to the light fixture.
3. The foundation on which the luminaire is to be installed must correspond to the maximum permissible pressure load of
the luminaire. Suitable drainage must also be provided. Level the body in two horizontal planes using the three leveling
tabs around outer body. The upper edge of the housing must be flush with the prepared surface into which it is recessed.
UNDER NO CIRCUMSTANCES MAY IT BE LOWER!
4. Unthread lens assembly from body with tool provided. Ensure that all internal surfaces of the fixture are kept
completely dry during installation. Pry out the accessory gasket by using a screw driver. Carefully by hand remove
reflector.
5. Connect incoming leads to quick disconnect plug. GREEN WIRE TO “GROUND”, CONNECT BLACK FIXTURE
TO BLACK BUIDLING WIRE AND CONNECT WHITE FIXTURE WIRE TO WHITE BUILDING WIRE. Replace
tray, lamp, and reflector. Make sure that no wires have been damaged.
6. If using conduit entries, the entries must be sealed with “Dap Heavy Duty Kwik Foam” (not provided). The foam
should be sprayed from inside the fixture up into the conduit. Failure by the contractor to use the DAP product could cause
a void in the warranty. Replace tray with lamping. If not using through wiring, plug second conduit entry with 3/4"
conduit plug. Please make sure wet label requirements are meet.
7. Install lamp and adjust if necessary. Tighten all screws to assure the lamp will not shift after aiming is acquired.
Replace reflector and accessory gasket.
8. Place lens frame over fixture ensuring that there is no foreign matter between the lens frame and the body. Start the
lamp and bring luminaire to operating temperature (20 to 30min.), this will evaporate the moisture content of air to
be trapped. Once operating temperature has been reached, carefully thread the trim assembly to body with tool provided.
DESIGNPLAN LIGHTING, INC., 79 TRENTON AVE, FRENCHTOWN, NJ 08825 T. 908-996-7710 F. 908-996-7042