PARTS LIST - Golden Lighting

advertisement
PARTS & ASSEMBLY SHEET
Fixture Name: Olympia 1648-BA3 BUS
This fixture assembled PO:
Date:
Notice: Please review the parts listing and check for all parts before assembling the fixture. If
any parts are missing or damaged, please note on this sheet and contact the place of
purchase to arrange for replacement parts.
PARTS LIST
Company Name:_____________ Co Account#:__________
below to be filled out by retailer
Mounting Strap
1ea 102X320mm
Green Screw
G8/32*H8 ㎜ 1ea
Mounting Screws
2ea
8/32"X5/8''mm
Wire Connectors
Orange 3ea
Mounting Screws
2ea
8/32X1"
Wall
2ea
Anchors
Anchor Screws
2ea N0.8X21''
Part Needed ______________________________
Quantity _________________________________
Part Needed ______________________________
Quantity _________________________________
Reason why (missing, scratched, broken glass, bent, bad finish)
Comments __________________________________________________________________________
1648-BA3 BUS
FIXTURE ASSEMBLY INSTRUCTIONS
Read and review installation instruction sheet
before assembling the fixture
Fig.1
1. Place Glass Shade (K) over the socket to
sit onto the glass holder.
2. Insert Candle Sleeve (L) onto the socket
and gently thread the sleeve onto the
socket to hold Glass Shade (K) into place.
3. Install the bulbs as per the fixtures
specifications.
(DO NOT EXCEED THE MAXIMUM WATTAGE RATING!)
NOTE: INSTALL THE SHADE ASSEMBLY AFTER THE
FIXTURE IS HUNG.
For Customer Service, contact the place of purchase to arrange for replacement parts.
1648-B A3 P ARTS ASSE MBLY SH E E T
INSTALLATION INSTRUCTIONS
Fixture Name: Olympia 1648-BA3 BUS
For Pendant Light Fixture
WARNING! SHUT POWER OFF AT FUSE OR CIRCUIT BREAKER
HANGING THE FIXTURE (Fig.1)
1. Carefully remove the new fixture from the carton along
with the yellow bag that holds all of the parts. Check that all
parts are included as shown in the illustration and the Parts
and Assembly Sheet.
2. Shut off the power at the circuit breaker and completely
remove the old fixture from the wall, including the old
mounting strap.
3. Place Mounting Strap (B) over the Junction Box.
4. Attach Mounting Strap (B) to the Junction Box using
Mounting Screws (A). Tighten the screws securely using a
screw driver.
Fig. 1
CONNECTING THE WIRES (Fig.2)
5. Attach the power supply wires to the fixture lead wires by
connecting BLACK to BLACK (or SMOOTH) and WHITE to
WHITE ( or RIBBED) .
6. Ground wire connection: Connect the fixture ground
Fig.2
wire to house ground wire, which usually has green or
copper insulation, with the correct size of wire
connector. If there is no house ground wire at ceiling
junction box then attach fixture ground wire securely
onto green grounding screw located on the mounting
bar.
HOUSE WIRES
BLACK
FIXTURE WIRES
WHITE
SMOOTH (BLACK)
GREEN
(Ground)
RIBBED (WHITE)
NOTE: Twist the wires together in the same direction that you
twisted the wire connector onto the wires.
7. Tuck the wire connections neatly into the Junction Box.
BARE COPPER
(Ground)
Fig.3
FINISHING THE INSTALLATION (Fig.3)
8. Raise the fixture to the wall so that it covers the Junction
Box.
9. Align the holes at both sides of Mounting Strap (B) with the
holes in the Backplate. Secure the Backplate to the
Junction Box using Mounting Screws (I) and a screw driver.
10. Install the light bulbs and glass shade as per the Parts and
Assembly Sheet.
F For Customer Service, contact Toll Free: 800.277.0979 Ext. 0 or Email: service@laureldesigns.biz
1648-B A3 I NSTALL ATI O N I NSTRU CTI O N
Download