TEST INFORMATION
FOR THE
LIGHT DUTY
HYBRID/ELECTRIC VEHICLE
SPECIALIST TEST (L3)
• OVERVIEW
• TEST SPECIFICATIONS
• TASK LIST
• CERTIFICATION TEST REFERENCE
• SAMPLE QUESTIONS
• INDUSTRY TRAINING
Light Duty Hybrid/Electric
Vehicle Specialist Test
Overview
Introduction
The Light Duty Hybrid/Electric Vehicle Specialist (L3) Test is the first advanced level test offered by ASE for
light duty hybrid/electric vehicle technicians. It is designed to measure a technician’s knowledge of the skills
needed to diagnose both high and low voltage electrical/electronic problems, as well as other supporting
system problems, on hybrid/electric vehicles. It is an extension of the repair and diagnostic skills tested by
the Automobile Electrical/Electronic Systems (A6) and Engine Performance (A8) tests. To register to take
the L3 certification test, you must have passed both the Automobile Electrical/Electronic Systems (A6) and
Engine Performance (A8) tests.
The L3 test consists of ## scored multiple choice questions. The questions require your familiarity with the
supplied reference materials, as this information is used to bridge gaps in your familiarization with
technology and terminology among various hybrid/electric vehicle platforms.
Registration information is available on the ASE website at www.ase.com. This website will provide the test
dates and other important information. On the ASE website, you can also create your own myASE
account, giving you direct access to your personal ASE certification information and more.
Who Writes the Questions?
Each question has its roots in an ASE “question-writing” workshop, where service representatives from
automobile manufacturers, aftermarket trainers, working technicians, and vocational educators meet to
share ideas and translate them into test questions. Each test question written by these experts must survive
review by all members of the group. The questions deal with practical problems experienced by technicians
in their daily work. Naturally, the failures described in the advanced level questions are more complex and
challenging.
From there, all questions are pre-tested and quality-checked on a national sample of technicians. Those
questions that meet ASE standards of quality and accuracy are included in the scored sections of future
tests; the “rejects” are sent back to the drawing board or are discarded altogether.
How Do I Prepare for the ASE L3 Test?
To prepare for the test, you need this book which includes the Hybrid Specialist Certification Test
Reference (print version or online at www.ase.com). We suggest that you follow these steps:
Page 2
Step 1. Study the content areas listed in the Test Specifications, noting what percentage of the
test each covers.
Step 2. Carefully read the Task List, noting the areas in which your skills are strong or weak.
Do this by checking off each task that you do not perform often or do not understand completely.
Step 3. Practice on the sample questions that follow. Although the sample questions will not appear
in the test, they are similar in style and difficulty to the actual test questions.
Step 4. Use steps 1 through 3 to identify any skill areas where you need additional study or
training. Then refer to the Industry Training reference section to locate the training sources that
are right for you.
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
What is the ASE Light Duty Hybrid/Electric Vehicle Specialist
Certification Test Reference?
The ASE Light Duty Hybrid/Electric Vehicle Specialist Certification Test Reference (starting on page 7 in this
book) is a resource that identifies concepts for the hybrid/electric vehicle technology that will be included in
the ASE test. The reference is included in this study guide and will also be available as a pop-up document
during the Certification Test. The first page outlines the concepts for the common technical constructs for all
hybrid/electric vehicle drive systems included in the test. All test questions will follow this outline to
ensure that the test content remains consistent and is understandable to candidates regardless of their
area of hybrid/electric vehicle specialty. The block diagrams illustrate systems similar to those used in many
hybrid/electric vehicles. These diagrams will serve as a visual reference and identify a vehicle classification
for each of the platforms based on technical characteristics. Vehicle classifications will be used in some
test questions to define the specific hybrid/electric vehicle type referenced in the scenario. The “Glossary
of Terms” can be used as a reference to clarify differences in how a term is used by various hybrid/electric
vehicle manufacturers.
The majority of the test questions will be generic, meaning the concept identified should be applicable to
most of today’s hybrid/electric vehicles. There will be some questions that will apply only to the Type-1,
Type-2 or Type-3 vehicle platforms identified in the block diagrams. You should become familiar with the
technology associated with all of these vehicle platforms, since questions about each may be included.
Please take the time to review all of the information contained in the Certification Test Reference before
taking the test.
Before the Test
Try to be well rested for the test so you will be alert and efficient. Be sure to bring along your test center
admission ticket and some form of current (unexpired) government-issued photo identification, like a driver’s
license. You do not need to bring this book. The Hybrid Specialist Certification Test Reference will be
provided as an electronic pop-up document during your test session.
How Long Are the Tests?
Test
Name
L3
Light Duty Hybrid/Electric Vehicle Specialist
# of Questions Testing Time
45*
2 hrs
*Note: The test will include 10 additional questions that are for statistical research purposes only. Your
answers to these questions will not affect your score, but since you do not know which ones they are, you
should answer all questions in the test.
At the Test Center
Lockers will be available for you to store your personal items, including cell phones. Pencils and scratch
paper will be provided for you in the test room.
Once the test begins, be sure to read each question carefully (twice, if necessary) so that you understand
exactly what is being asked. There are no “trick” questions. Each question tests a specific diagnostic skill
and has a single correct answer.
If you are unsure of an answer, don’t get stuck. Mark the answer that you think is correct and flag the
question using the on-screen button. Then go on to the next question. If you finish before the allotted time
is up, you can go back to the flagged questions. It is to your advantage to answer every question. Do not
leave any answers blank. Your score is based on the total number of correct answers that you give.
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 3
TEST SPECIFICATIONS
FOR THE LIGHT DUTY HYBRID/ELECTRIC
VEHICLE SPECIALIST TEST (L3)
Content Area
Questions in Test
A. Battery System
B. Internal Combustion Engine
C. Drive Systems
D. Power Electronics E. Hybrid Supporting Systems
Total:
Percentage of Test
11
6
9
13
6
____
45*
25%
13%
20%
29%
13%
____
100%
*Note: The L3 Certification test will include 10 additional questions that are for statistical
research purposes only. Your answers to these questions will not affect your score, but since
you do not know which ones they are, you should answer all questions in the test.
Page 4
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
LIGHT DUTY HYBRID/ELECTRIC
VEHICLE SPECIALIST TEST
TASK LIST
A. Battery System (11 questions)
1. Perform high voltage disconnect procedure; reconnect/enable high voltage system.
2. Select, test and use proper safety gloves.
3. Select, qualify and use proper DMM and leads.
4. Retrieve and diagnose DTCs; determine needed repairs.
5. Diagnose problems caused by damaged or failed harnesses, connectors, terminals and fuses.
6. Diagnose high voltage (HV) battery pack malfunctions.
7. Remove and replace high voltage battery pack.
8. Test, diagnose and repair high voltage leaks / loss of isolation.
9. Test, diagnose and repair high voltage battery pack heating and cooling systems.
10.Test, diagnose, repair or replace high voltage battery pack internal components.
B. Internal Combustion Engine (6 questions)
1. Retrieve and diagnose DTCs; determine needed repairs
2. Determine if the internal combustion engine is in CRANK mode or RUN mode.
3. Differentiate between driveability problems caused by the internal combustion engine and/or hybrid
drive system.
4. Perform internal combustion engine cranking compression test.
5. Keep the internal combustion engine running during service.
6. Diagnose internal combustion engine no-crank condition.
7. Diagnose internal combustion engine cranks/no-start condition.
8. Interpret vacuum and compression readings on Atkinson cycle engines.
9. Identify engine start/stop strategy; diagnose malfunctions.
10.Service engine cooling system.
C. Drive Systems (9 questions)
1. Perform high voltage disconnect procedure; reconnect/enable high voltage system.
2. Select, test and use proper safety gloves.
3. Select, qualify and use proper DMM and leads.
4. Retrieve and diagnose driveline DTCs; determine needed repairs.
5. Diagnose problems caused by damaged or failed harnesses, connectors, and terminals.
6. Identify transmission fluid and coolant fluid requirements; verify fluid levels.
7. Test, diagnose and repair high voltage leaks/loss of isolation.
8. R&R rotor from stator.
9. Diagnose drive/traction motor-generator assembly for improper operation (such as an inoperative
condition, noise, shudder, overheating, etc.).
10.Diagnose improper electrically actuated parking pawl operation; determine needed repair.
11.Diagnose motor-rotor position sensor (Resolver or Encoder type).
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 5
D. Power Electronics (13 questions)
1. Perform high voltage disconnect procedure; reconnect/enable high voltage system.
2. Select, test and use proper safety gloves.
3. Select, qualify and use proper DMM and leads.
4. Retrieve and diagnose DTCs; determine needed repairs.
5. Diagnose problems caused by damaged or failed harnesses, connectors, and terminals.
6. Identify procedures necessary to establish the proper vehicle operational power mode during service
(OFF, ACCESSORY, POWER ON, READY TO DRIVE).
7. Diagnose the cause of illuminated hybrid drive related warning light/message or driveability
complaint.
8. Diagnose impact sensor problems: determine needed repair.
9. Diagnose AC/DC inverter overheating; determine needed repair.
10.Diagnose AC/DC inverter failure; determine needed repair.
11.Replace AC/DC inverter cooling pump.
12.R&R AC/DC inverter.
13.Diagnose and repair communication network; determine needed repair.
14.Locate and test the voltage level of capacitors.
15.Diagnose, locate and safely disable/enable safety interlocks.
16.Diagnose failed DC/DC converter; determine needed repair.
17.R&R DC/DC converter.
18.Test high voltage cable integrity and loss of isolation using a scan tool and/or an insulation
resistance meter.
19.Perform 12-volt battery testing.
20.Diagnose system main relay (SMR)/contactor malfunctions; determine needed repairs.
E. Hybrid Supporting Systems (6 questions)
1. Perform high voltage disconnect procedure; reconnect/enable high voltage system.
2. Select, test and use proper safety gloves.
3. Select, qualify and use proper DMM and leads.
4. Diagnose problems caused by damaged or failed harnesses, connectors, and terminals.
5. Retrieve and diagnose DTCs; determine needed repairs.
6. Inspect EVAP emission system components; determine needed repairs.
7. Observe and interpret driver indicators, power flow display and energy monitor; determine necessary
action.
8. Test and diagnose high voltage air conditioning compressor malfunctions; diagnose poor system
performance; determine needed repairs.
9. R&R high voltage air conditioning compressor; identify and select proper system oil.
10.Diagnose inadequate cabin heating; determine needed repair.
11.Diagnose and repair electric/electronic steering systems.
12.Diagnose brake system performance problems; differentiate between braking problems caused by
hydraulic system and regenerative system malfunctions; determine needed repairs.
13.Deactivate brake system self-test prior to service.
14. Service liquid cooling system(s).
Page 6
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Certification Test Reference Page 1 of 3
ASE LIGHT DUTY
HYBRID/ELECTRIC VEHICLE SPECIALIST
CERTIFICATION TEST REFERENCE
The block diagrams included in this document represent the power flow strategies used by the
hybrid-drive systems included in the ASE Light Duty Hybrid/Electric Vehicle Specialist test.
Although additional details may be provided in individual test questions, the following information
should be considered common to each of these systems.
• All represented hybrid-systems are high-voltage. These systems typically exceed 100 volts, but
systems greater than 60 volts DC or AC RMS should be considered high-voltage.
• All motor/generators (MG) are high-voltage three-phase AC electric motor/generators.
• Each vehicle type is equipped with a high-voltage (HV) battery pack. Neither battery chemistry nor total
battery pack voltage are defined in this general description document.
• Each system uses a DC/AC bi-directional inverter to provide AC current to and from the
motor/generator(s).
• Each system uses a DC/DC converter. This converter supplies stepped-down voltage to the vehicle’s
12 V system and replaces the traditional generator (alternator).
• All systems are equipped with a 12 V battery.
• Failures affecting the vehicle’s electric drive system may result in the display of a “Hybrid System
Warning” on the instrument panel.
• The terms Encoder and Resolver may be used interchangeably.
• Because of the variation in terminology used by different manufacturers when referring to the hybrid
system’s readiness state, ASE test questions will use the following to indicate the operational power
modes.
OFF
ACCESSORY
POWER ON
READY TO DRIVE
All systems OFF. The engine and electric drive system are powered
OFF.
Same as ACC on a conventional vehicle.
Equivalent to KOEO – Key ON/Engine OFF. In this mode, the engine
will not run, nor will the vehicle move under electric power.
Equivalent to KOER – Key On/Engine Running. In this mode, the
vehicle is ready to drive. The engine is running, or is OFF and ready
to run if so commanded. The electric drive system is also ready for a
drive command.
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 7
Certification Test Reference Page 2 of 3
Type-1
The Type-1 hybrid-drive system uses power
from the internal combustion engine (ICE) and/
or motor/generator(s) to propel the
vehicle. Power flow to the drive-wheels is
blended as needed through a planetary gear
set, with motor/generator 1 (MG1) serving as a
reaction unit to control the effective ratio and
direction of the gears. MG1 is used as the
starter motor for the ICE, and conversely, it
can be driven by the ICE to act as a generator.
MG2 also serves as a generator during
regenerative braking.
The Type-2 hybrid-drive system uses a
single motor/generator (MG) integrally
mounted between the internal combustion
engine (ICE) and the transmission. The ICE
and MG are used together to maximize
vehicle propulsion. During regenerative
braking, the MG acts as a generator.Under
most conditions, the MG serves as the
starter motor for the ICE. Some Type-2
vehicles may be equipped with an auxiliary 12
V starter motor. Power flow to the drive wheels
can be provided by a split-pulley/steel belt
continuously variable transmission, a
conventional automatic transmission, or a
standard transmission.
INTERNAL
COMBUSTION
ENGINE (ICE)
ICE
MG
TRANSAXLE
Type-2
Page 8
CLUTCHES
ICE
MG1
PLANETARY
GEAR SET
INTERNAL
COMBUSTION
ENGINE (ICE)
CLUTCHES
The Type-3 hybrid-drive system is regarded as
an extended range electric vehicle. MG2
provides vehicle propulsion and electrical
regeneration while braking. In certain
situations, MG1 assists MG2 by combining
power flow through a planetary gear set to
reduce the speed of MG2. When the
high-voltage (HV) battery pack falls to a
predetermined state-of-charge (SOC), the
internal combustion engine (ICE) drives MG1
to generate sufficient current to power MG2
and maintain the HV battery pack.
CLUTCHES
Type-3
MG2
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Certification Test Reference Page 3 of 3
Light Duty Hybrid/Electric
Vehicle Specialist Test
Glossary of Terms
The reference materials and questions for this test use electronic and emission terms and acronyms that are
consistent with the industry-wide SAE standards J1715, J1930, and J2012. Some of these terms are listed
below.
Auto Stop - In the READY TO DRIVE (KOER) operational power mode, the internal combustion engine is
automatically turned off when power demand is zero or negative, such as during vehicle stop, and then
restarted automatically.
Battery Cell - An assembly of a positive electrode, a negative electrode, and other necessary
electrochemical and structural components. A cell is a self-contained energy conversion device whose
function is to deliver electrical energy to an external circuit via an internal chemical process.
Battery Module - A grouping of interconnected cells in a single mechanical and electrical unit.
Battery Pack/Traction Battery - Interconnected battery modules that have been configured for a specific
energy storage application.
Battery System - Completely functional energy storage system consisting of the pack(s) and necessary
ancillary subsystems for physical support, thermal management, and electronic control.
DC/DC Boost Converter - A power converter that produces an output voltage greater than (boost) or less
than (buck) the input voltage.
Energy Monitor - A display that indicates the charge/discharge status of the high voltage battery.
Hybrid System Warning - A display on the instrument panel that is activated when failures affecting the
vehicle’s electric drive system are detected. This display is the same as a “Master Warning Light,” “Service
Hybrid System” message, “IMA Warning Light,” etc.
ICE - Internal Combustion Engine
IGBT - Insulated Gate Bipolar Transistor
Motor/Generator - An electromechanical device that can operate in two modes without changing rotational
direction. As a motor, it consumes electricity to produce mechanical power. As a generator, it consumes
mechanical power to produce electricity.
Power Flow Display - An animated graphic indicating the direction of the flow of energy.
Service Life (years or cycles) - A general term that describes the length of time a battery can remain in
service. Service life can be specified in terms of either time or duty cycles.
Service Plug - A high-voltage electrical disconnect device that is used when performing repairs on the high
voltage hybrid/electric vehicle circuits.
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 9
Light Duty Hybrid/Electric Vehicle Specialist Test
Sample Questions
NOTE: The ASE Light Duty Hybrid/Electric Certification Test Reference (pages 7-9 in this study guide) will
be available to you as a pop-up document on the computer screen while you are taking the L3 test, but you
should become familiar with it before that time. It may be helpful to review those pages before you attempt
the following questions.
1. A hybrid vehicle equipped with push button start will enter the POWER ON (KOEO) mode, but will not
enter the READY TO DRIVE (KOER) mode. No diagnostic trouble codes (DTCs) are stored. This could be caused by:
(A)
(B)
(C)
(D)
the high voltage safety plug is removed.
a failed brake on/off switch.
an empty fuel tank.
a disconnected 12 V battery.
Question #1 Explanation:
Answer (A) is wrong. If the high voltage (HV) safety plug was removed, the vehicle would enter the
POWER ON (KOEO) mode, but would not enter the READY TO DRIVE (KOER) mode. However, with
the safety plug removed, a DTC would be stored.
Answer (B) is correct. If the brake on/off weitch was failed, the vehicle would enter the POWER ON
(KOEO) mode. However, a failed breake on/off switch would not allow the hybrid ECU to confirm that
the brake pedal is applied, which is necessary for entering the READY TO DRIVE (KOER) mode. It is
possible that the ECU may not yet have recognized the lack of a feedback signal from the failed
switch so a DTC may not yet be stored.
Answer (C) is wrong. With an empty fuel tank, the vehicle would enter the POWER ON (KOEO) mode
and the READY TO DRIVE (KOER) modes as long as the high voltage battery maintains a sufficient
state-of-charge. However, the internal combustion engine (ICE) would crank, but would not start due
to the lack of fuel in the tank. This condition would set a DTC because the ICE did not start.
Answer (D) is wrong. A disconnected 12 V battery would prevent the vehicle from entering any
operational power mode since the hybrid ECU would not power up.
2. Technician A says that after disabling the high voltage battery system, a special DMM is required to
confirm voltage levels are safe for performaing system service.
Technician B says that removing the 12 V system negative battery cable will make the high voltage
battery system safe to service/repair.
Who is right?
(A) A only
(B) B only
Page 10
(C) Both A and B
(D) Neither A nor B
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
3. A Type-1 hybrid vehicle will enter READY TO DRIVE (KOER) mode but will not crank the internal
combusion engine (ICE). When the vehicle is pushed in NEUTRAL gear range, the engine spins.
Which of these could be the cause?
(A)
(B)
(C)
(D)
A depleted high voltage battery
A seized MG2
A failed crankshaft position sensor
A seized plenetary gear set
4. During deceleration, the arrows on the power flow display appear as shown. This indicates:
(A)
(B)
(C)
(D)
the engine is running with energy flowing to the drive wheels.
the engine is running and driving the motor/generator to recharge the battery pack.
energy from the battery pack and the engine are blended and flowing to the drive wheels.
energy from the drive wheels is being used to recharge the battery pack.
5. A Type-2 hybrid vehicle with a belt type continuously variable transmission (CVT) bucks and jerks
when accelerating from a stop.
Technician A says that using the wrong type of transmission fluid could be the cause.
Technician B says that a failing split pulley/steel belt could be the cause.
Who is right?
A) A only
(B) B only
(C) Both A and B
(D) Neither A nor B
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 11
6. The MIL is illuminated and a “Battery Module Deterioration” diagnostic trouble code (DTC) is stored.
The most likely cause is a failed:
(A)
(B)
(C)
(D)
high voltage battery.
high voltage inverter.
motor/generator.
DC/DC converter.
Answer Key: 1.B 2.A 3.D 4.D 5.C 6.A
Page 12
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Light Duty Hybrid/Electric Vehicle Specialist Test
Industry Training
The training sources listed in this guide are designed to help you sharpen your technical skills in hybrid/
electric vehicle diagnostics. Since the L3 test reflects these skills - the more you learn, the better your
chances are of passing this test.
Please contact the listed organizations for availability, schedules, and prices. In addition, many new
sources of training in this area are being developed. You may wish to check with auto manufacturers,
community colleges, tool and equipment suppliers, and technical training organizations for the latest
training information. Training resources can also be found on ASE’s home page at www.ase.com, or the
International Automotive Technicians Network (iATN) at www.iatn.net.
ACDelco offers training in a variety of delivery methods to ensure the maximum learning benefit for the
service professional. In addition to traditional instructor-led technical training courses and seminars, a wide
selection of online courses are also available. For more information about all training offerings, visit www.
acdelcotechconnect.com or call ACDelco at (800) 825-5886.
Automotive Video, Inc. offers several different video training programs covering hybrid vehicle diagnosis
and repair. These include HVAC systems, case studies, and safety for first responders. For more
information, call: (800) 718-7246. Internet: www.auto-video.com
Automotive Technician Training Services offers seminars, webinars, and self-study training courses all
designed to help technicians stay in touch with the latest diagnostic and repair procedures. Instructor-led/
hands-on training is also offered for hybrid vehicle diagnosis. Technician-trainers deliver the instructor-led
seminars and webinars. Self-study materials deliver information that will both teach, and enhance
diagnostic skills. ATTS Training Center, 10 Lupi Plaza, Mahopac, NY 10541 Call:(845) 628-1062. Internet:
www.attstraining.com
Auto Career Development Center (ACDC) offers training classes, seminars, webinars, DVDs and
manuals covering all aspects of hybrid and electric vehicle diagnosis and repair. Instructor-led training
classes are a comprehensive mix of classroom education followed up by hands-on application in the shop
working on hybrid/electric vehicles. All material covers the most popular hybrid/electric vehicles found in
production today. For more information, call 800-939-7909. Internet: www.fixhybrid.com.
CARQUEST The Training and Certification System (TACS) provides a full scope of training solutions. This
includes the ability to setup a career path for instructor-led training, online training, ASE Test Prep Study
Guides, Technical Assessments, and more. Visit their website for more information. Internet:
www.ctionline.com
Cengage Learning provides training textbooks and online, interactive courseware covering many areas
of automotive repair, including hybrid/electric vehicles. The online interactive computer program is called
Technician Test Preparation (TTP). TTP is designed to help prepare technicians for the ASE tests. For a free
catalog, write: Cengage Learning, P.O. Box 8007, Clifton Park, NY 12065, or call (800) 347-7707. Internet:
www.trainingbay.com.
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 13
Delphi Product and Service Solutions offers technical training materials and classes with real world
applications to today’s vehicles. All content has been developed by drawing on experience from working with
many different vehicle manufacturers. Training products include textbook and CD-ROM formats, including
hybrid/electric vehicles. Instructor led training classes covering a wide range of topics are also available. An
overview of all training products and services is available on the website. Internet: http://delphi.com/tools
Phone: (877) 550-TECH
Motor Age Training for ASE Certification is a self-study training guide that is updated regularly and contains
both technical information and sample questions. For ordering information, write: Motor Age Training, P.O.
Box 6310, Duluth, MN 55806.Phone: (800) 240-1968; Web:www.PassTheASE.com
The Mechanic’s Education Association (MEA) is a technician-based organization in New Jersey that
offers over 100 instructor-led and online courses, which include the latest in hybrid/electric vehicle diagnosis.
They also offer a telediagnostic hotline, and an on-site diagnostic van to help with the toughest problems.
For information, contact: MEA, 1805 Springfield Ave., Maplewood, NJ 07040, or call (973) 426-9001.
Internet: www.meatraining.com
NAPA Auto Parts is an ASE CASE accredited training provider offering a broad spectrum of automobile and
light/medium duty vehicle training options. These include ASE test preparation classes, assessments,
e-learning and instructor-led training. NAPA Autotech provides quality real world / problem solving technical
training solutions for today’s technicians that include leading technologies and the latest repair techniques.
Regularly scheduled classes are offered nationwide as well as custom training solutions. For more
information about training offerings, visit www.NAPAAutotech.com or call (800) 292-6428.
Perfect Sky conducts hands-on workshops for technicians who want to learn how to diagnose and repair
hybrid, plug-in hybrid, and electric vehicles. Workshop size is restricted to a maximum of twelve students.
For more information, call (310) 383-4800.
Standard Motor Products, Inc. offers professional technician seminars that focus on real-world problems
and solutions, not just theory. Engage in actual diagnosis using case studies in the shop to apply what
you’ve learned. An ASE-Certified professional instructor conducts the four-hour seminars during the
evening, with a heavy emphasis on diagnostics and troubleshooting. Each seminar includes a workbook for
your reference after the class. SMP also offers 70 live, as well as a number of archived, one-hour long
webinars. These can be viewed anywhere an internet connection is available, including at home.
Internet: http://pts.smpcorp.com
VEEJER Enterprises offers training in automotive electrical diagnosis and repair and vehicle electronics
troubleshooting. Training programs are designed to teach step-by-step methods used for performing
electrical repairs, as well as the skills necessary for troubleshooting electrical and electronic problems in
both low voltage and high voltage (HV) systems. Training programs cover the use of a DMM, current clamp,
digital logic probe, scope meter, and dual-trace lab scope when testing and diagnosing electrical and
electronic circuits. Training is offered through home-study programs, as well as hands-on instructor led
electrical/electronics trouble-shooting training workshops. For more information, contact: Veejer Enterprises,
3701 Lariat Lane, Garland, TX 75042-5419, or call (972) 276-9642. Internet: www.veejer.com.
Page 14
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
© 2016 by the
National Institute for
Automotive Service Excellence
All rights reserved
ASE Light Duty Hybrid/Electric Vehicle Specialist Test Information
Page 15
National Institute for
AUTOMOTIVE
SERVICE
EXCELLENCE
www.ase.com
101 Blue Seal Dr. SE, Suite 101
Leesburg, VA 20175
(703) 669-6600
TO:
Related documents