A RCHI T ECT ’S G UIDE
WI NDOW H A RDWA RE
September 2008
Architect’s Guide
W I N D O W
H A R D W A R E
Kirsch, the most widely specified window hardware brand, offers a
complete selection of window hardware and drapery heading systems
suitable for virtually any installation. This guide will assist you in
selecting and specifying the best solution for your facility needs.
W W W. K I R S C H . C O M
This manual is designed to assist in the selection of
Kirsch custom window hardware and special heading
systems for various kinds of installations. It is divided
into three convenient sections:
Architect’s Guide
1. Kirsch custom window heading systems
W I N D O W
3. Basic component parts and specifications
for each track system.
H A R D W A R E
Window treatment
products for every
commercial and
residential need
Founded in 1907, Kirsch is the
world’s leading manufacturer
of window hardware. Kirsch
pioneered the development
of custom Architrac® and
drapery heading systems
to offer architects, interior
designers and construction
specifiers top quality, precisely
engineered products for
commercial, institutional and
residential applications.
Commercial/Contract
Customer Service
Toll-Free 800-776-5788
Specific product
information
Individual product brochures
are available for Ripplefold®
and Baton Draw. Write for
them or call toll-free.
Teflon® is a registered trademark of DuPont®
Celcon® is a registered trademark of Ticona®
2
2. Performance data of track systems
Drapery Heading Systems
Ripplefold® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Baton Draw systems . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Track Systems Performance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6-7
Draw Cord Operation
94001 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8-9
93001 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10-11
9095 Series . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
Superfine® Contract Rods . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Baton or Hand Drawn Operations
Application & Suggested Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . 14-15
– 94003 Series
– 94004 Series
– 94005 Series
– 94008 Series
– 9046 Series
Component Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Cubicle Track Systems
Application & Popular Configurations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
– 9600 Series
– 9046 Series
Component Parts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Installation Aids . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Drapery Heading Systems
Ripplefold and Conventional Pleats
ARCHITECT’S
GUIDE
Drapery Heading Systems
There are two headings that
can be used with the various
Kirsch Architrac® series. Each
system uses a different pleating
method to achieve unique and
beautiful decorating effects.
The custom heading system
Ripplefold® offers definite
benefits. It is designed for
attractive appearance from
both inside and outside a
building — an advantage to
designers who desire uniformity
in the exterior appearance of a
building. All custom tracks are
designed for easy installation
and maintenance.
Ripplefold®
Soft ripple-like folds flow smoothly from
one end of the track to the other. The
effect is gently tailored — suitable for
commercial or residential installations.
Spaced carriers control drapery fullness.
Features
• Panels can be pressed flat,
yet fall into folds.
• Headings are suspended
under the track.
• No hooks or pins.
• Stackback space is less than conventional draperies.
• Draperies easily snap on and off carriers.
Recommendations
Recommended where draperies require frequent launderings, such as hospitals
and institutions. Draperies have uniform ripple-like appearance inside and outside.
Note: When drapery pins can cause a safety hazard, use Ripplefold® snap systems.
Conventional
Pleats
Familiar pinch-pleated draperies
are attached to slide carriers with
slip-in or pin-on hooks. Draperies
can be custom-made or ready made.
To select proper track system for
this heading, see chart page 6.
Features
• Can be used with most track systems.
• Headings can be suspended under
the track or over the face of it.
• Most familiar of the heading systems.
• Can be tied back for effect.
3
ARCHITECT’S
GUIDE
Drapery Heading System
Ripplefold®
Ripplefold® Drapery Heading System
An unbroken flow of softly rippled folds. Gently disciplined,
uniquely fabricated so the panels can be pressed flat yet
automatically fall into folds. Suitable for either commercial or
residential installations. Folds are identically beautiful from
inside the room or from outside the building — an architectural
advantage. Stackback space is less. Headings are suspended
under the track. Draperies easily snap on and off from carriers.
Select fullness from four differently spaced snap carriers.
Drapery specifications
Finished drapery panels to be
fabricated per instructions in Kirsch
Ripplefold Guide, F0337008, using
No. 92145 stiffened nylon tape with
snaps on 4¼" centers.
Bottom hems to be 4” wide with Kirsch
No. 1615 covered lead weights in
corner of each panel.
Spaced carriers control
drapery fullness
Applications
Can be used on track systems.
For track specifications refer to page 6.
Standard carriers
Cord draw
No. 94001 Series
• Spaced snap carriers for use with all
track systems except Nos. 93001
No. 93001 Series
• No. 92140 for 120% fullness
• No. 92141 for 100% fullness
• No. 92142 for 80% fullness
92145
(For Baton Draw, use F0337018
Fabrication Guide)
No. 93601 Series
• No. 92143 for 60% fullness
Baton draw
Front load carriers
No. 94003 Series
• Slide shoes for use with front load
track systems Series 93001
No. 94004 Series
• No. 93140 for 120% fullness
• No. 93141 for 100% fullness
• No. 93142 for 80% fullness
No. 94005 Series
• No. 93143 for 60% fullness
No. 9046 Series
No. 94008 Series
4
ARCHITECT’S
GUIDE
Baton Draw System
For use with Ripplefold and Conventional Pleats
Baton Draw System with Sewn-on Stiffener
Custom Hand Draw System
Designed for a variety of commercial and institutional applications.
Ideal for motels, hotels, dormitories, etc., where drapery and rod
wear present special maintenance problems and costs. Puts baton in
view of the user. No hidden cords. Just push or pull baton to open
and close draperies. Multi-wheel masters will take torque in any
direction. Can be used with conventional pleated and Ripplefold®
heading systems.
Features
Component Parts
Specifications
• Stiffener is sewn and grommeted to
drapery overlap.
Multi-wheel baton masters
• Stiffener socket is placed over
master arm.
Nos. 94134 and 94133
Use with conventional pleated draperies
• Furnish and install Kirsch hand draw
track Series 94003, 94004, 94005, or
94008
• Baton is attached by a screw
through the eyelet and into the
master arm.
• Draperies to be grommeted with
eyelet.
• 92900 tooling with 94147 eyelet die
required to grommet drapery.
• Specify 2½', 3', 4', 5' or 6' baton.
94134
Left hand
Eyelet
94133
Right hand
Nos. 94136 and 94135
Use with Ripplefold heading systems
Master
Arm
Stiffener
Socket
Baton
For conventional
pleated draperies
Masters
No. 94133 R.H.
No. 94134 L.H
Stiffener
No. 94145
For Ripplefold
Masters
No. 94135 R.H.
No. 94136 L.H
Back side of drapery
Baton
Front side of drapery
• Track to be equipped with
appropriate components for
heading system selected.
94134
Left hand
Stiffeners
No. 94145
Overlap stiffener with eyelet
94133
Right hand
Stiffener
No. 94146
Refer to Baton Draw Systems Brochure
F0337018
For use with conventional pleated
drapery trim; use with 94004.
No. 94146
Overlap stiffener with eyelet
For Ripplefold panels.
Eyelet
Supplied with stiffeners
5
ARCHITECT’S
GUIDE
Track Systems
Performance Data and Installation Application
Track Systems Performance Data
SERIES
CROSS
SEC TION
MA X TR ACK SE T LENGTH
BENDING
RADIUS
HEADING
SYSTEMS
Cord Draw Systems
93001
One-Way Draw
Two-Way Draw
16 ft.
32 ft.
12" *†
Conventional Pleated
Ripplefold∞
93601
One-Way Draw
Two-Way Draw
16 ft.
32 ft.
Not Available
Conventional Pleated
Ripplefold∞
12" *†
Conventional Pleated
Ripplefold∞
Track set is opened and
closed by traverse cord.
Continuous cord loop
permits use of cord
tension pulley.
94001
One-Way Draw
Two-Way Draw
½" pulley
1" pulley
16 ft.
32 ft.
20 ft.
40 ft.
9095
One-Way Draw
Two-Way Draw
24 ft.
32 ft.
8" *
Conventional Pleated
3000
(Superfine)
One-Way Draw
Two-Way Draw
12½ ft.
25 ft.
Not Available
Conventional Pleated
Track set is opened and
closed by hand — no
cord involved.
94003
One-Way Draw
Two-Way Draw
20 ft.
40 ft.
12" *†
Conventional Pleated
Cubicle Curtain
Ripplefold
Fiberglass batons,
attached to lead carriers,
are recommended for
traversing draperies.
94004
One-Way Draw
Two-Way Draw
16 ft.
32 ft.
Not Available
Conventional Pleated
Cubicle Curtain
Ripplefold
94005
One-Way Draw
Two-Way Draw
16 ft.
32 ft.
12" *†
Conventional Pleated
Cubicle Curtain
Ripplefold
9046
One-Way Draw
Two-Way Draw
16 ft.
20 ft.
8" or 12" *
Conventional Pleated
Cubicle Curtain
Ripplefold
94008
One-Way Draw
Two-Way Draw
16 ft.
32 ft.
Not Available
Pinch pleats
Cubicle Curtain
Ripplefold
Hand Draw Cordless Systems
Maximum track lengths and
maximum fabric weight
do not apply to curved
track. Send complete
specifications and fabric
weight to customer
service for feasibility.
Footnotes
6
†
* Can be angular bent using radius listed or circular curved.
† NOTE: Nos. 93001, 94001, 94003, 94005 and 9046 can be curved to a larger semi-circle
radius. Contact customer service for more information.
∞ Maximum length for
one-way draw Ripplefold®
track systems is 16 feet.
Track Systems
Performance Data and Installation Application
ARCHITECT’S
GUIDE
Installation Application
A P P L I C AT I O N & B R A C K E T C L E A R A N C E
C E I L I N G I N S TA L L AT I O N
I N T E R M E D I AT E
S U P P O R T S PA C I N G
W A L L I N S TA L L AT I O N
M A X FA B R I C W E I G H T
Track perforated 16" on center for direct
½" pulley ¾" pulley
mounting with screw. Wall Mount:
One-Way Draw 32 lbs. 32 lbs.
Two brackets at each end 24" apart,
Two-Way Draw 32 lbs. 40 lbs.
48" apart over remainder of track.
No brackets
required
2"- 3"
No. 1796
No. 94130
3½" - 4½"
Two brackets at each end
24" apart, 48" apart over
remainder of track
1½"
Single
2¼" - 3¼"
Double
1¼" - 2½"
Two brackets at each end
24" apart, 48" apart over
remainder of track
No brackets
required
2"- 3"
4" - 5"
Drop-in
2"- 3"
Push-in
2"- 3"
Two brackets at each end
24" apart, 48" apart over
remainder of track
2"
3½" - 4½" ¥
Two brackets at each end
24” apart, 48” apart over
remainder of track
One-Way Draw
Two-Way Draw
48 lbs.
56 lbs.
LBS
PER
FOOT
2
2
3
3.5
½" pulley ¾" pulley
One-Way Draw 32 lbs.
Two-Way Draw 32 lbs.
64 lbs.
80 lbs.
3.1
2
30 lbs.
45 lbs.
1.9
One-Way Draw
Two-Way Draw
15 lbs.
20 lbs.
1
1.8
One-Way Draw
Two-Way Draw
40 lbs.
80 lbs.
2
2
One-Way Draw
1 support 16" from each end,
32" apart over remainder of track Two-Way Draw
1.4
No brackets
required
Not Available
Track perforated 16" on center for One-Way Draw
direct mounting with screws
Two-Way Draw
32 lbs.
64 lbs.
2
2
No brackets
required
Not Available
Track perforated 16" on center for One-Way Draw
direct mounting with screws
Two-Way Draw
32 lbs.
64 lbs.
2
2
No brackets
required
Not Available
Track perforated 16" on center for One-Way Draw
direct mounting with screws
Two-Way Draw
32 lbs.
64 lbs.
2
2
Track perforated 16" on center for direct
One-Way Draw
mounting with screw. Wall Mount:
Two brackets at each end 24" apart, Two-Way Draw
48" apart over remainder of track.
32 lbs.
64 lbs.
2
2
3"
3½" - 4½"
¥
¥ Wall or mullion installation
7
ARCHITECT’S
GUIDE
Architrac
Series 94001 Track
Architrac Series 94001 Track
• Separate channels for operating equipment and carriers which
hold draperies.
• Will accommodate Ripplefold® and standard pleated draperies.
• Remove and add slides with snap open end gate.
Description
Brackets
Component Parts
• For wall or ceiling mounting.
Standard Pulley set
Nos. 94119 and 94120
• Dual-channel, cord operated.
• Extruded .050" No. 6063T5
aluminum alloy, etched and
anodized.
• White baked enamel finish.
• Two end pulleys to choose from for
either lightweight or heavyweight
draperies.
15⁄16"
Drapery
Heading
No. 94130
Bracket for ceiling mounting
27⁄16"
• Multiwheel roller-bearing masters
prevent any binding and give easy
traversing.
1½"
1¼"
35⁄8"
Min. Pocket
11/16"
¾"
No. 94130
Bracket for recess mounting
½" diameter Teflon® bearings for
standard weight draperies where
minimum stackback and uniform
folding to the end of the rod is desired.
Heavy Duty Pulley set
Nos. 94101 and 94102
Actual size — end view
Applications
Mounts on wall or ceiling (flush
or recess). For spans up to 40’ in a
two-way draw. Track can be curved.
This track series will accommodate
Ripplefold® and conventional pleated
drapery heading systems.
No. 94125
Double bracket for wall mounting
1" diameter heavy duty ball bearing
pulley sets for heavier installations,
larger spans.
Requires use of rod notching tool No. 9997
No. 94122
Bracket for wall mounting
3½" return
8
Architrac
Series 94001 Track
Conventional
Heading Systems
Assembled Sets
Master Carriers for conventional
pleated draperies
Nos. 94104 and 94103
Set includes assembled rod, 94122 wall
or 94130 ceiling brackets and 9923
cord tension pulley; longer brackets
can be ordered separately. Rod may be
angular bent or circular curved.
Brackets:
Wall or ceiling mount.
Multiwheel roller-bearing masters.
Regardless of torque, master rollers
won’t bind.
Optional Operational
Components
Butt Master Carriers
Nos. 94118 and 94117
Draperies:
Pinch Pleat, Ripplefold® (butt or overlap
masters and fullness).
Fabrication and Planning Guides:
Ripplefold®-Tape: refer to F0337008
• Furnish and install, as indicated
on plans, Kirsch Track No. 94001,
extruded of .050" 6063T5 aluminum
alloy in accordance with Aluminum
Association Specification.
No.AA-C22A21. Finish (25) White,
Baked Enamel
• Specify Mounting Brackets
and Quantity
–
–
–
94117
Right hand
Drapery panels
butt together at center.
No flat areas or overlap shadow.
Ceiling
Wall – Single Track
Wall – Double Track
• Specify Drapery System and Fullness
–
–
Standard Pleated
Ripplefold® 120%, 100%, 80%, 60%
• Specify Master
–
Butt Master
Overlap Master
• End Pulley Options
–
Set with ½" end pulley
No. 94270
Finish (25) White, Baked Enamel
94118
Left hand
Suggested Specifications
–
Set with 1" end pulley
No. 94270H
Finish (25) White, Baked Enamel
ARCHITECT’S
GUIDE
–
½" Teflon® Bearing
Nos. 94119 and 94120
1" H.D. Ball Bearing
Nos. 94101 and 94102
• No. 9934 polyester cord, used with
½" Teflon® end and 1" ball bearing
end pulley set.
• Tension Pulley to be No. 9923
Overlap Master Carriers
Nos. 94116 and 94115
94116
Left hand
94115
Right hand
Drapery panels
overlap at center.
9
ARCHITECT’S
GUIDE
Architrac II
Series 93001 Track
Architrac II Series 93001 Track
• Front loading carrier system for easy hanging of draperies.
• Large opening carrier channel accepts standard hex socket drivers
for direct ceiling installation
• Available with either ¾" or ½" end pulley sets.
• Choice of butt or overlap masters.
• Sliding edges coated with lubrication for smooth traversing action.
Description
Applications
• For wall or ceiling mounting.
Mounts on wall or ceiling. Track can
be curved to any angle using a 12"
radius or circular curve. Can be used
in two-way draw for spans up to 32’.
Will accommodate Ripplefold® and
pinch pleated draperies.
• Dual-channel, cord operated.
• Extruded .050" No. 6063T5
aluminum alloy, etched and
anodized.
• Finish is white.
• Two end pulleys to choose from for
either lightweight or heavyweight
draperies.
1½"
5/8" 3/4"
1/2"
Drapery
Heading
Actual size — end view
Ceiling Installations
Install directly through pre-drilled
holes (16" intervals) in track and end
pulleys. Use fasteners which yield
direct withdrawal strength of 25 lbs.
Wall Installations
Two brackets at each end of track
24" apart, 48" apart over remainder of
track.
Component Parts
Pulleys
One-way draw
No. 93103
Two-way draw
½" dia.; max load 32 lbs.
No. 93101
Left hand
No. 93102
Right hand
Heavy Duty
¾" dia. with Teflon bearings;
Max load 64 lbs.
No. 93091
Left hand
No. 93092
Right hand
Carriers
Nos. 93140-93143
Space slide shoes for Ripplefold systems
No. 93123
Slide shoe
No. 93121
Snap carrier
10
Architrac II
Series 93001 Track
Component Parts
Assembled Sets
No. 93138
End bracket
No. 93139
Wall bracket
2"- 3" clear
• Specify Mount
A. Surface direct or No. 93138
ceiling brackets
B. Wall — No. 93139 brackets
Overlap Master Carriers
Nos. 93107 and 93106
Set includes assembled rod, standard
wall or ceiling brackets and 9923 cord
tension pulley. Longer brackets must
be ordered separately. Rod may be
angular bent or circular curved.
93106
Right hand
Butt Master Carriers
Nos. 93105 and 93104
Fabrication and Planning Guides:
Ripplefold®: Refer to F4730002
Track with heavy duty pulleys
No. 93150H
Finish (25) White, Baked Enamel
Track with standard pulleys
No. 93150
Finish (25) White, Baked Enamel
93105
Left hand
Suggested Specifications
• Furnish and install, as indicated
on plans, Kirsch Track No.
93001, extruded of .050” 6063T5
aluminum alloy in accordance with
Aluminum Association Specification
No. AA-C22A21. Finish to be (25)
white, baked enamel
Brackets
93107
Left hand
ARCHITECT’S
GUIDE
• Specify Drapery System and Fullness
A. Conventional pleated
B. Ripplefold® 120%, 100%, 80%, 60%
• Specify Master Slides
A. Butt Masters:
Nos. 93104 and 93105
B. Overlap Masters:
Nos. 93106 and 93107
• End Pulley Options
A. Regular: No. 93102
B. Heavy Duty: Nos. 93091 and
93092
• Cord to be No. 9934 polyester
• Cord Guide to be Nos. 9945 or 9923
tension pulley
93104
Right hand
Maximum capacity specifications for H.D. Architrac (series 93001)
Maximum widths are determined in part by
available track lengths. Splicing is not
recommended. Maximum loads apply when
using Kirsch Ripplefold® drapery systems.
No. 93001, when installed with medium
weight fabric on standard size windows (i.e.,
16’ wide by 8’ high) will operate with a 2-3
lb. pull requirement. When installed with a
maximum load, it will operate with a 5-6 lb.
pull requirement.
NOTE: All components have been tested under
conditions simulating ten years’ usage. Snaps
will detach with a 4 lb. “peel” action and
release with a sheer pull of 22 lbs.
Maximum loads
Type of fabric based on 48" goods – 5 oz.
per linear yard. Unlined sheer or lightweight
fabrics. Size of draperies to equal 32 lbs. based
on 100% fullness 16’ wide x 32’ long – 32’ wide
x 16’ long
Type of fabric based on 48" goods – 10 oz.
per linear yard. Lined sheers or lightweight
fabrics. Size of draperies to equal 32 lbs. based
on 100% fullness 16’ wide x 16’ long – 32’ wide
x 8’ long.
Type of fabric based on 48" goods – 20 oz.
per linear yard. Lined medium weight fabrics
or heavy cotton, velours and linens. Size of
draperies to equal 32 lbs. based on 100%
fullness 16’ wide x 8’ long
11
ARCHITECT’S
GUIDE
Double Duty Rodding
Series 9095 Track
Double Duty Rodding Series 9095 Track
•
•
•
•
22 gauge steel (.030"), white baked enamel finish.
Extra strong and rugged deluxe traverse line.
Push-in style brackets for fast mounting.
Flange construction provides extra strength; makes surface
mounting easy.
• Cords are completely concealed in track.
Description
Component Parts
• For wall or ceiling mounting. Use
with conventional draperies only.
Master Carriers
• Single channel, cord operation.
• Can be curved to 8" radius.
• Ball bearing pulleys.
• Self-lubricating slides.
• Concealed cord, can’t sag.
7/8"
No. 9497
One-piece construction permits free
overlap of draperies when closed.
Slide Carriers
1"
No. 3909
Molded of special formula,
self-lubricating.
Pulleys
Actual size — end view
Application
Surface or recess mounting. Holes
pre-drilled in integral mounting flange
on 16" centers for direct mount with
Hex or Pan Head screws.
No. 9287N
Ball Bearing pulley set
Easy operation at unusually wide or
high spans or with heavy panels.
Supports & Brackets
7/8"
Ceiling mount
1"
7/16"
Track is perforated through flange; 16"
on center. No brackets or supports
needed. Use the same components for
wall or ceiling mounts. Use choice of
bracket/support projections.
12
No. 9592
Intermediate Support
No. 3311-3312
Push-in End Brackets
1"- 2" clearance: No. 3311
2"- 3" clearance: No. 3312
Cord
No. 9934
Braided cord
Suggested Specifications
• Furnish and install, as indicated on
plans, Kirsch track No. 9095, formed
of .030" 22 gauge steel with baked
enamel finish inside and out. To be
used with Kirsch components.
• End pulley Sets to be push-in style
with ball bearings, No. 9287.
• End brackets to be push-in style.
All supports to be fastened with
appropriate fastening devices to
provide 25 lbs. withdrawal strength
per device.
• Cord to be polyester, No. 9934, and
rigged for tension pulley.
Superfine®
Contract Rods
ARCHITECT’S
GUIDE
Superfine® Contract Rods
• White Baked enamel finish.
• All sliding edges have lubricated coating.
• Extra strength master slides.
• Teflon end pulleys for quiet, longer life.
• Universal cam lock supports for easy installation, secure hold.
• Kirsch Contract Rods are economically bulk packed for commercial installation.
Description
Component Parts
• Adjustable
• For wall or ceiling mounting
Supports & Brackets
• White finish, conventional adjustable
traverse rod.
• Roll formed of heavy gauge steel.
• Choice of drop-in or push-in
mounting brackets.
No. 3576
Universal cam support
• Kirsch Contract Rods are
economically bulk packed for
commercial installation.
No. 3558
Universal cam support
5/8"
• Heavy duty, adjustable traverse rods
to be Kirsch No. 3083R Series. Rod
sections to be 24 gauge (.021") steel,
white baked enamel finish.
• Tolerances between rod sections
are not to exceed plus minus .010",
assuring trouble free, telescoping
joints.
• Rods to have ¾" diameter pulleys
and self-lubricating slides. Cords
to be No. 4 (4/32" diameter) braided
polyester.
• Brackets, supports and cord tension
pulleys are to be ordered separately.
11/16"
17/16"
Suggested Specifications
(outside)
No. 3311
Push-in bracket
• Choice of drop-in or push-in
mounting brackets. Specify size:
–
–
–
–
–
No. 3301
Drop-in bracket
–
–
–
30" - 48"
38" - 66"
48" - 86"
66" - 120"
86" - 156"
120" - 224"
100" - 180"
160" - 300"
13
ARCHITECT’S
GUIDE
Baton or Hand Draw
Series Nos. 94003 and 94004
Baton or Hand Draw
Description
• Extruded .050" high strength, 6063T5
aluminum alloy single channel tracks
etched and anodized in natural
finish in accordance with Aluminum
Association Specification
No. AA-C22A21.
• For cordless traverse operation.
• All sliding edges lubricated with
Kirlon® except 94008.
No. 94003
No. 94004
Application
Application
• Hand draw.
• Hand draw.
• Wall or Ceiling mount.
• Ceiling mount.
• White baked enamel finish.
• White baked enamel finish.
• Can be bent to any angle using 12"
radius; larger semi-circular radius
curved at factory.
• Rear flange perforated on 16"
centers for direct ceiling mount;
no need to screw through channel.
• Track cannot be curved.
Wall mount
Ceiling mount
Suggested Specifications
Suggested Specifications
• Track
– Furnish and install, as indicated on plans,
Kirsch track NO. 94003, extruded of .050"
6063T5 Aluminum alloy etched and
anodized.
• Track
– Furnish and install, as indicated on
plans, track No. 94004, extruded of .050"
6063T5 Aluminum. Track to be fastened
securely at 16" intervals through predrilled holes.
• Specify Finish:
– (25) White
• Ball Bearing / Wheeled Slides:
Use No. 9603 End Cap and
No. 94113-94114 Master Carrier
– No. 9670 Ball Bearing style
– No. 9687 Ball Bearing style
– No. 9673 Ball Bearing style
– No. 9678R Wheeled style
14
Ceiling mount
• Specify Finish:
– (25) White
• Ball Bearing / Wheeled Slides:
Use No. 94113 or 94114 Master Carrier
– No. 9670 Ball Bearing style
– No. 9687 Ball Bearing style
– No. 9673 Ball Bearing style
– No. 9678R Wheeled style
• Button Slides:
Use with No. 9684 End Stop and No. 9644
Master Carrier with Button Style Slides
– No. 9406 Button Style
– No. 9685 Button Style
– No. 9686 Button Style
• Button Slides:
Use No. 9644 Master Carrier and
No. 9684 End Stop
– No. 9406 Button Style
– No. 9685 Button Style
– No. 9686 Button Style
• Specify Mounting Bracket:
– Wall Mount: No. 94132V
(2" - 3" Clearance)
– Ceiling Mount: No. 94140. One Bracket
to be mounted at each end of track.
(One 24" from each drapery stacking
end and one at 48" intervals over
remainder of track).
• Specify End Cap:
– No. 94142
Baton or Hand Draw
Series Nos. 94005, 9046 and 94008
ARCHITECT’S
GUIDE
No. 94005
No. 9046
No. 94008
Application
Application
Application
• Hand draw.
• Hand draw
• Hand draw.
• Ceiling mount.
• Ceiling mount.
• Wall or ceiling mount.
• White baked enamel finish.
• White baked enamel finish.
• White baked enamel finish.
• Can be bent to any angle using 12"
radius; semi-circular curves of 48"
radius (min.) can be curved at factory.
• Track perforated on 16" centers.
• Cannot be bent.
Ceiling mount
• Can be bent to any angle using 8"
or 12" radius; semi-circular curves of
48" radius (min.) can be curved at
factory.
Ceiling mount
Wall mount
Ceiling mount
Suggested Specifications
Suggested Specifications
Suggested Specifications
• Track
– Furnish and install, as indicated on
plans, track No. 94005, extruded of .050"
6063T5 Aluminum. Track to be fastened
securely at 16" intervals through
pre-drilled holes.
• Track:
– Furnish and install, as indicated on
plans, Kirsch track No. 94008, rolled of
22 gauge (.030") Galvanized Steel, White
Baked Enamel Finish.
• Track:
– Furnish and install, as indicated on plans,
Kirsch track No. 9046, extruded of .070"
6063T5 Aluminum alloy etched and
anodized.
• Ball Bearing / Wheeled Slides:
Use No. 94113 or 94114 Master Carrier
– No. 9670 Ball Bearing style
– No. 9687 Ball Bearing Style
– No. 9673 Ball Bearing style
– No. 9678R Wheeled style
• Ball Bearing / Wheeled Slides:
Use No. 94113 or 94114 Master Carrier and
No. 9603 End Cap
– No. 9670 Ball Bearing style
– No. 9687 Ball Bearing Style
– No. 9673 Ball Bearing style
– No. 9678R Wheeled style
• Finish:
– (25) White
• Button Slides:
Use No. 9644 Master Carrier and
No. 9684 End Stop
– No. 9406 Button Style
– No. 9685 Button Style
– No. 9686 Button Style.
• Button Slides:
Use No. 9644 Master Carrier and
No. 9684 End Stop
– No. 9406 Button Style
– No. 9685 Button Style
– No. 9686 Button Style
• Specify End Cap:
– No. 94141
• Specify Mounting Brackets:
– Wall Mount: No. 94132V
(2" - 3" Clearance)
– Ceiling Mount: No. 94140. One Bracket
to be mounted at each end of track.
(One 24" from each drapery stacking
end and one at 48" intervals over
remainder of track).
– NOTE: Fastening devices should have a
minimum 25lb. direct withdrawal strength.
Screws used through channel openings
should be a Phillips or #6 posidrive head.
• Specify Slide Carrier:
– No. 9406 Button Style
– No. 9685 Button Style
– No. 9686 Button Style.
• Specify Master Carrier:
– No. 9644
– No. 94158 & 94159
• Specify End Cap:
– No. 9684
– No. 9682
15
ARCHITECT’S
GUIDE
Baton or Hand Draw
Components
Baton or Hand Draw Components
Track Splices
Butt Master Carriers
No. 94110
Use with Track No. 94003
Drapery panels
butt together at center.
No flat areas or overlap shadow.
Overlap Master Carriers
Nos. 94136 and 94135
No. 9686
Slide Carrier with hook,
without bead chain.
Standard drop 3½" (other
drops available at extra cost).
Drapery panels
overlap at center
No. 9673
Ball Bearing Carrier
with attached hook
Nos. 94174 and 94173
Over the top master carrier.
No. 9678R
Wheeled Carrier
94134
Left hand
94174 — Left hand
94133
Right hand
End Stops
No. 9684
End Stop with pin-hole return
Nos. 94134 and 94133
No. 9683
94173 — Right hand
End Caps
Nos. 94114 and 94113
94134
Left hand
Slide Carriers
94114
Left hand
94113
Right hand
No. 9644
May be used with batons.
No. 9670
Slide Carrier
Must use No. 9683 end stops
and No. 9644 masters
No. 9406
Button Carrier
Lubri-side molded Celcon;
glides smoothly in track
Nos. 94159 and 94158
For batons, Ripplefold® and
conventional pleat draperies
(panels must hang below track).
94159
Left hand
16
94158
Right hand
No. 9685
Button Carrier (No. 9406)
with attached hook
No. 9687
Ball Bearing Carrier
with hook, without chain.
Has eyelets for
No. 9688 chain.
94133
Right hand
No. 9682
No. 94141
Use with Track No.
94003, 94005
No. 94142
Use with Track No.
94003, 94005
Batons with Harness Snaps
For use with cordless hand draw.
White finish.
3/8" Fiberglass
1/4" Steel
Length
No. 91232
No. 91233
No. 91234
No. 91235
No. 91236
91332R
91333R
91334R
2½'
3'
4'
5'
6'
Baton Draw Multi-Wheel Masters for 94133 and
94134 Pinch Pleat for extra overlap; 94135 and
94136 for Ripplefold®. Requires use of 94145 or
94146 stiffeners (see page 5).
Cubicle Track Sytem
Series Nos. 9600 and 9046
ARCHITECT’S
GUIDE
Cubicle Track System
Popular Configurations
for Intravenous or
Cubicle Installations
BED
No. 9600
No. 9046
Application
Application
• Excellent choice for privacy
curtains in hospitals and
extended care facilities.
• Good quality track for use with
cubicle or pinch-pleated curtains.
Description
Description
• Track is 29/32" x 11/16" x .050 extruded
6063T5 anodized aluminum.
• Track is 5/8" x 1/2" x .070 extruded
6063T5 anodized aluminum.
• Inner surface is center ridgegrooved for easy installation.
• Lubricated with Kirlon for frictionfree operation.
• If specified, tracks will be bent
or circular curved from one
continuous length up to 20'.
Bends will be approx. 14" radius.
• If specified, tracks will be bent
or circular curved from one
continuous length up to 16'.
Bends will be approx. 8" or 12"
radius.
• Maximum weight per foot:
2.4 pounds.
BED
BED
BED
No. 9601/090
33" track with 90˚ bend.
20½"
BED
20½"
No. 9605/090
Track with 90˚ bend, 9616 carriers, 9610
end stops and 9611 pull-out.
BED
17
ARCHITECT’S
GUIDE
Cubicle Track System
Components
Components for Cubicle Track System
No. 9046
No. 9600
No. 9600
Overlap Master Carriers
Carriers
Drapery panels
overlap at center
No. 9623
Ceiling Flange
No. 9633
Carrier body and wheels
made of Celcon
No. 9644/061
Master slide for pinch-pleated panels;
permits draperies to overlap for
privacy.
No. 9624
Track Socket
No. 9616/061
Carrier (No. 9633) with
attached hook. Eye and
hook of .093 bright basic
wire, nickel plated.
Track Splices
Slide Carriers
No. 9612
No. 9406/061
Button Carrier
Lubri-side molded Celcon;
glides smoothly in track
End Stops
No. 9685/061
Button Carrier (No. 9406)
with attached zinc-plated
.080 wire hook designed for
grommeted panels
No. 9610
End Stop
No. 9611
Pull-out
7⁄8"
No. 9620/12
Suspension Tubing
¾" x ¾"
No. 9689
16" PVC Hanger
End Caps
No. 9686/061
Slide Carrier with hook,
without bead chain.
Standard drop 3½" (other
drops available at extra cost).
No. 9613
End Cap
No. 9690
16" Hook Chain
Supports & Brackets
End Caps
No. 9682
No. 9637
Support
End Stops
No. 9684
18
No. 9639
Bracket
No. 9693
End Ring for shortening
hook chain
Installation Aids
Suspended Ceiling Clips amd Channel Protectors
ARCHITECT’S
GUIDE
Installation Aids
Suspended Ceiling Clips
Channel Protector
No. 9520
No. 9955
Can be used for mounting
Architrac rod sets on
suspended type ceilings
where conventional
surface mounting with
screws and/or mounting
devices is not possible.
Plastic channel protector
should be used as shown.
Place inside the track during
ceiling or recess mounting
of surface track to prevent
damage to sliding surface.
Use with 94005, 94008 and
9046 tracks.
Do not use Hex head screws.
Must use low profile heads.
19
www.kirsch.com
To place orders, verify status
or obtain the latest product information,
Call toll-free 1-800-817-6344
or Fax toll-free: 1-800-308-4293
For express service, have your customer
code readily available.
Kirsch Window Fashions ©2008
4110 Premier Drive, High Point, NC 27265
Phone: 1-800-817-6344 • Fax: 1-800-308-4293
www.kirsch.com
F0291008
Updated 9/08