Brochure - Boston Light Source

advertisement
SAE SYSTEMS™
simple
affordable
efficient
P-ID-9800 matches the shape of the
indirect perforated, slotted, or solid
9800. Three diffuser options are
available: all follow the curve of the
housing for a clean design look.
Precision-tooled 4-, 8-, and 12-foot
all-steel construction ensures a highquality installation for the varied
requirements of office, classroom,
and retail applications.
P-ID-9800
SAE Systems™
Type:
Project:
P-ID-9800
Pendant-Mounted Indirect/Direct
98id
Specifications
HOUSING. Die-formed steel with downlight opening, 3 11/16" x 41 1/4", in each four-foot section of fixture.
Diffuser opening starts at 3 3/8" from each fixture end. At the center of eight-foot fixtures and four-feet from the ends of
twelve-foot fixtures openings are spaced 6 3/4" end-to-end, to match spacing between openings in joined fixtures.
END CAPS. End caps are 14-gauge steel with no holes or knockouts, finished to match housing.
REFLECTORS. Die-formed high-reflectance aluminum side reflectors. Optional Distribution Separator Reflector (DSR)
9 3/4"
allows three-lamp fixtures to deliver separately switched uplight and downlight.
(248)
LAMPING. Available in one-, two-, and three-lamp T5, T5HO, or T8.
BALLAST. Electronic Ballast (ELB - for T8 lamping) or Low-profile Electronic Ballast (LP/ELB - for T5 or T5HO lamping), high power factor, thermally protected Class
P, Sound Rated A, less than 10% THD, manufactured by a UL Listed manufacturer, as available, determined by Litecontrol. Ballasts with a voltage range of 120 to 277
will be used when fixture configuration and ballast availability allow. The minimum number of ballasts will be used.
TANDEM WIRING. When selected from Ordering guide below, fixtures wired to switch in-line lamps separately, providing two or three (three-lamp cross-section
fixtures only) levels of light.
PRE-WIRING. Fixtures are supplied with #12 AWG type THHN wire for branch circuits. One end will have factory-installed push-in quick-connects. The other end will
be stripped back 1/2" for quick connection in field. For fixtures to accommodate special circuits such as night light and emergency, etc., in-field wiring will be required.
ROW JOINING. Fixture end headers are threaded in two locations to allow easy row joining without removing reflectors. Support points are centered above the
midpoint of joint “on seam” for aligned, symmetrical appearance.
SYSTEM CONNECTORS. Corners, tees, and crosses available. Connectors are die-formed steel, same profile as housing, with no exposed fasteners or knockouts.
Each system connector shall have a rigid cross-member with a .687" diameter stem hole at center to accept any of Litecontrol’s pendant assemblies.
SUSPENSION. Yoke with field adjustable aircraft cable attaches directly to the end header. Mounting points in rows are exactly “on module” at 48," 96," and 144,"
including at ends of rows.
CERTIFICATION. Fixture and electrical components shall be UL and/or CUL Listed and shall bear the I.B.E.W., A.F. of L. label.
3 1/8"
(80)
Note: Litecontrol reserves the right to change specifications without notice for product development and improvement.
For complete ordering and technical information, including photometric report summaries, and pre-wiring information, please see technical sheet online at litecontrol.com for the P-ID-9800.
Ordering guide
Product, Lamping, & Length
P -
ID -
98
6
8
T5 -
SGL -
TCWM -
TW -
LP/ELB -
2CWQ -
LP/EF -
120
Mounting
Distribution
Series
Lamp
Count
Lamp
Type
Diffuser
Finish
Tandem
Wiring
Ballast
Pre-Wiring
Other
options
Volts
P
PendantMounted
ID
Indirect/
Direct
98
1, 2, 3
2, 4, 6
3, 6, 9
1, 2, 3
2, 4, 6
3, 6, 9
see
notes
Nominal
Length
(ft)
4
8
12
4
8
12
T8
PBSS
PBSS/O
PBCWM
PBCWM/O
SGL
TCWM
(Textured
Matte
White) is
standard
-TW
1CWQ
2CWQ
120
277
see
Diffusers
see
LiteColors™
in Product
Guide for
other
finishes
LP/EF
F
DSR
see
Other
options
Mounting
- add to end of order number
Aircraft Cables
FAI/ACC (field adjustable) standard
T5HO
T5
Cross-section lamping
1-T5 or T5HO
1-T8
2-T5 or T5HO
2-T8
3-T5 or T5HO
3-T8
Radiused Parabolic Semi-specular Baffle.
30 cells, producing 30° lengthwise shielding.
PBSS/O
Radiused Parabolic Semi-specular Baffle, with Overlay.
For additional diffusing of lamp(s), Matte White acrylic
overlay provided to lay over baffle blades.
PBCWM
Radiused Parabolic Baffle finished Matte White.
30 cells producing 30° lengthwise shielding.
PBCWM/O Radiused Parabolic Baffle finished Matte White, with
Overlay. For additional diffusing of lamp(s), Matte
White acrylic overlay provided to lay over baffle blades.
SGL
Soft Glow Lens. Extruded frosted acrylic,
follows contour of fixture housing.
100 Hawks Avenue
ELB is std for T8
LP/ELB is std for
T5 or T5HO
DA/ELB
HEL/ELB
notes:
ECO/ELB
Lamp Count = total number of lamps in the fixture
ELB/HLO (T8 only) Tandem Wiring not available for one-lamp
cross-section fixtures
see
For Ordering guide information in shaded areas,
Ballast
choose selection by reading ACROSS the shaded
Options
areas for correct specifications.
P-ID-9868T5-SGL-TCWM-TW-LP/ELB-2CWQ-LP/EF-120-FAI/ACC is a typical catalog number for a
6-lamp (3 lamps in cross-section), 8-foot long T5 fixture with Soft Glow Lens, Textured Matte White finish,
tandem-wired low-profile electronic ballast, pre-wired with two-circuit branch wiring and quick-connects,
low-profile emergency fluorescent ballast, 120 volts, mounted with field adjustable aircraft cables.
Ballast options
Diffusers
PBSS
see
notes
Specify in place of ELB or LP/ELB , contact factory for availability/compatibility with lamping:
DA/ELB
Advance Mark VII Dimming Ballast.
HEL/ELB Osram Sylvania Dimming Ballast.
ECO/ELB Lutron ECO-10 Dimming Ballast.
ELB/HLO High Light Output Ballast. For 25-30% increased lumen output for standard
F32T8 lamps. Available from various UL Listed manufacturers, as determined
by Litecontrol. T8 only
Other options
LP/EF
F
DSR
. . . an employee owned company
Hanson
MA
02341
781 294 0100
Low-profile Emergency Fluorescent Ballast. Battery-powered ballast from a
UL Listed manufacturer will operate one lamp for 1 1/2 hours.
Fuse. Slow or fast blow, determined by Litecontrol.
Distribution Separator Reflector. Allows fixtures to deliver separate uplight and
downlight with three-lamp cross-section. Requires tandem wiring (TW) to
provide separate switching of downlight. No tools required for
installation. Finish is Matte White.
FAX 781 293 2849
info@litecontrol.com
litecontrol.com
© 2006 LITECONTROL, Printed in U.S.A./BO10032-00
Options
Download