D
Last Updated: May 1, 2006
default (ccn application)
default (ccn engine)
default (ccn trigger jtapi)
default (ccn trigger sip)
default ccm-manager (ccn subsystem jtapi)
default ctiport (ccn subsystem jtapi)
default gateway (ccn subsystem sip)
default security password length min
default security pin length min
description (ccn application)
dtmf-relay
Cisco Unity Express 2.3 Command Reference
OL-10351-02
59
D
default (ccn application)
default (ccn application)
To reset a CCN application parameter to its default value, use the default command in CCN application
configuration mode.
default {description | enabled | maxsessions | parameter name}
Syntax Description
description
Sets the application description to the name of the application.
enabled
Enables the application.
maxsessions
Sets the maximum number of sessions to the port license number.
parameter name
Sets the parameter’s value to the default set in the script.
Note
Parameter names can be viewed using the show ccn application
command.
Command Modes
CCN application configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Usage Guidelines
The default command sets a Cisco Unified Communication Network (CCN) application parameter to its
default value.
Examples
The following example sets the maximum number of sessions to the port license number:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn application voicemail
se-10-0-0-0(config-application)# default maxsessions
se-10-0-0-0(config-application)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto attendant.
ccn engine
Configures the parameters used by all CCN applications.
Cisco Unity Express 2.3 Command Reference
60
OL-10351-02
D
default (ccn application)
Command
Description
ccn trigger sip
phonenumber
Configures CCN trigger values for the applications.
show ccn application
Displays all of the CCN application details.
Cisco Unity Express 2.3 Command Reference
OL-10351-02
61
D
default (ccn engine)
default (ccn engine)
To set the upper limit on the number of steps executed in a CCN application to the default value, use the
default command in CCN engine configuration mode.
default maxsteps
Syntax Description
maxsteps
Command Modes
CCN engine configuration mode
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
Upper limit on the number of steps executed in a CCN application. The
default is 1000.
The following example resets the specified parameters to their factory values:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn engine
se-10-0-0-0(config-engine)# default maxsteps
se-10-0-0-0(config-engine)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto attendant.
ccn engine
Configures the parameters used by all CCN applications.
ccn trigger sip
phonenumber
Configures CCN trigger values for the applications.
show ccn engine
Displays the CCN engine information.
Cisco Unity Express 2.3 Command Reference
62
OL-10351-02
D
default (ccn trigger jtapi)
default (ccn trigger jtapi)
To reset a CCN JTAPI trigger parameter to its default value, use the default command in CCN trigger
JTAPI configuration mode. To disable the trigger or to set the number of maxsessions to 0, use the no
form of this command.
default {application | enabled | idletimeout | locale | maxsessions}
no default {enabled | maxsessions}
Syntax Description
application
Has no effect on the application.
enabled
Enables the trigger. Use the no form of this command to disable the trigger.
idletimeout
Sets the idle timeout to 10,000 seconds.
locale
Sets the locale to “systemDefault.”
maxsessions
Sets the maximum number of sessions to the port license number. Use the
no form of this command to set the number to 0.
Command Modes
CCN trigger JTAPI configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
The following example sets the maximum number of sessions to the port license number:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger jtapi phonenumber 1234
se-10-0-0-0(config-trigger)# default maxsessions
se-10-0-0-0(config-trigger)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto attendant.
ccn engine
Configures the parameters used by all CCN applications.
show ccn trigger
Displays all of the CCN application details.
Cisco Unity Express 2.3 Command Reference
OL-10351-02
63
D
default (ccn trigger sip)
default (ccn trigger sip)
To reset a CCN SIP trigger parameter to its default value, use the default command in CCN trigger SIP
configuration mode. To disable the trigger or to set the number of maxsessions to 0, use the no form of
this command.
default {application | enabled | idletimeout | locale | maxsessions}
no default {enabled | maxsessions}
Syntax Description
application
Has no effect on the application.
enabled
Enables the trigger. Use the no form of this command to disable the trigger.
idletimeout
Sets the idle timeout to 10,000 seconds.
locale
Sets the locale to “systemDefault.”
maxsessions
Sets the maximum number of sessions to the port license number. Use the
no form of this command to set the number to 0.
Command Modes
CCN trigger SIP configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
The following example sets the maximum number of sessions to the port license number:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn trigger sip phonenumber 1234
se-10-0-0-0(config-trigger)# default maxsessions
se-10-0-0-0(config-trigger)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto attendant.
ccn engine
Configures the parameters used by all CCN applications.
show ccn trigger
Displays all of the CCN application details.
Cisco Unity Express 2.3 Command Reference
64
OL-10351-02
D
default ccm-manager (ccn subsystem jtapi)
default ccm-manager (ccn subsystem jtapi)
To reset a Cisco Unified Communications Manager JTAPI subsystem parameter used by Cisco Unity
Express to its default value, use the default ccm-manager command in Cisco Unity Express CCN
subsystem JTAPI configuration mode.
default ccm-manager {address | username | password}
Syntax Description
address
Sets the IP address of the Cisco Unified Communications Manager server
to 0.0.0.0.
username
Sets the CCM JTAPI username to an empty string.
password
Sets the CCM JTAPI password to an empty string.
Command Modes
CCN subsystem JTAPI configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
The following example sets the Cisco Unified Communications Manager server address to 0.0.0.0.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem jtapi
se-10-0-0-0(config-jtapi)# default ccm-manager address
se-10-0-0-0(config-jtapi)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto
attendant.
ccn engine
Configures the parameters used by all CCN applications.
ccn subsystem jtapi
Configures CCM JTAPI parameters.
ccn trigger sip phonenumber
Configures CCN trigger values for the applications.
show ccn subsystem jtapi
Displays the CCN subsystem JTAPI details.
Cisco Unity Express 2.3 Command Reference
OL-10351-02
65
D
default ctiport (ccn subsystem jtapi)
default ctiport (ccn subsystem jtapi)
To reset the Cisco Unified Communications Manager CTI port address to its default value (an empty
string), use the default ctiport command in Cisco Unity Express CCN subsystem JTAPI configuration
mode.
default ctiport
Syntax Description
This command has no arguments or keywords.
Command Modes
CCN subsystem JTAPI configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
The following example sets the Cisco Unified Communications Manager CTI port address to an empty
string.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem jtapi
se-10-0-0-0(config-jtapi)# default ctiport
se-10-0-0-0(config-jtapi)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto
attendant.
ccn engine
Configures the parameters used by all CCN applications.
ccn subsystem jtapi
Configures the CCM JTAPI parameters.
ccn trigger sip phonenumber
Configures CCN trigger values for the applications.
show ccn subsystem jtapi
Displays the CCN subsystem JTAPI details.
Cisco Unity Express 2.3 Command Reference
66
OL-10351-02
D
default gateway (ccn subsystem sip)
default gateway (ccn subsystem sip)
To reset a SIP server parameter to its default value, use the default gateway command in Cisco Unity
Express CCN subsystem SIP configuration mode.
default gateway {address | port}
Syntax Description
address
Sets the IP address of the SIP server to 0.0.0.0.
port
Sets the SIP port to 5060.
Command Modes
CCN subsystem SIP configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
The following example sets the SIP server port to 5060.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem sip
se-10-0-0-0(config-sip)# default gateway port
se-10-0-0-0(config-sip)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto
attendant.
ccn engine
Configures the parameters used by all CCN applications.
ccn subsystem sip
Configures the CCM JTAPI parameters.
ccn trigger sip phonenumber
Configures CCN trigger values for the applications.
show ccn subsystem sip
Displays the CCN subsystem SIP details.
Cisco Unity Express 2.3 Command Reference
OL-10351-02
67
D
default security password length min
default security password length min
To set the length of the security password to the default minimum, use the default security password
length min command in Cisco Unity Express configuration mode.
default security password length min
Syntax Description
This command has no arguments or keywords.
Defaults
The password length is 3.
Command Modes
Cisco Unity Express configuration
Command History
Cisco Unity Express Release
Modification
2.1
This command was introduced.
Examples
The following example resets the password length:
se-10-0-0-0# config t
se-10-0-0-0(config)# default security password length min
se-10-0-0-0(config)# end
Related Commands
Command
Description
security password
Configures the system-wide password length and expiry time.
show security detail
Displays the password and PIN settings.
Cisco Unity Express 2.3 Command Reference
68
OL-10351-02
D
default security pin length min
default security pin length min
To set the length of the security PIN to the default minimum, use the default security pin length min
command in Cisco Unity Express configuration mode.
default security pin length min
Syntax Description
This command has no arguments or keywords.
Defaults
The PIN length is 3.
Command Modes
Cisco Unity Express configuration
Command History
Cisco Unity Express Release
Modification
2.1
This command was introduced.
Examples
The following example resets the PIN length:
se-10-0-0-0# config t
se-10-0-0-0(config)# default security pin length min
se-10-0-0-0(config)# end
Related Commands
Command
Description
security pin
Configures the system-wide pin length and expiry time.
show security detail
Displays the password and PIN settings.
Cisco Unity Express 2.3 Command Reference
OL-10351-02
69
D
description (ccn application)
description (ccn application)
To specify an optional description for a CCN application, use the description command in Cisco Unity
Express CCN application configuration mode. To remove the description, use the no form of this
command.
description “text”
no description “text”
Syntax Description
text
Defaults
No string is defined.
Command Modes
CCN application configuration
Command History
Cisco Unity Express Release
Modification
1.0
This command was introduced on the Cisco Unity Express
network module and in Cisco Unified Communications
Manager Express 3.0.
1.1
This command was implemented on the advanced integration
module (AIM) and in Cisco Unified Communications Manager
3.3(3).
1.1.2
This command was implemented on the Cisco 2800 series and
Cisco 3800 series routers.
Examples
Specifies a text description for the application. Use double quotes around
the text.
The following example adds a description for the CCN autoattendant application:
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn application autoattendant
se-10-0-0-0(config-application)# description “Release 1 AA”
se-10-0-0-0(config-application)# end
se-10-0-0-0(config)# exit
Related Commands
Command
Description
ccn application
Configures the CCN applications, such as voice mail and auto attendant.
show ccn application
Displays the CCN application details.
Cisco Unity Express 2.3 Command Reference
70
OL-10351-02
D
dtmf-relay
dtmf-relay
To set the SIP DTMF relay mechanism, use the dtmf-relay command in Cisco Unity Express SIP
configuration mode. To use the default values, use the no or default form of this command.
dtmf-relay {rtp-nte | sub-notify | info | sip-notify}
no dtmf-relay
default dtmf-relay
Syntax Description
rtp-nte
Uses the media path to relay incoming and outgoing DTMF signals to
Cisco Unity Express.
sub-notify
Uses Subscribe and Notify messages to relay for incoming DTMF signals to
Cisco Unity Express. This option is not available for outgoing DTMF signals from
Cisco Unity Express.
info
Uses the Info message to relay outgoing DTMF signals from Cisco Unity Express
to the Cisco IOS SIP gateway.
sip-notify
Uses Unsolicited-Notify messages to relay incoming and outgoing DTMF signals.
Defaults
sip-notify, sub-notify is the default combination.
Command Modes
Cisco Unity Express SIP configuration
Command History
Cisco Unity Express Release
Modification
2.3
This command was introduced.
Usage Guidelines
To use the rtp-nte option, verify that the Cisco IOS SIP gateway is configured to use Unsolicited
NOTIFY for SIP calls, as shown in the following example:
dial-peer voice 1000 voip
destination-pattern 6700
session protocol sipv2
session target ipv4:10.100.9.6
dtmf-relay sip-notify rtp-nte
codec g711ulaw
no vad
To use the sip-notify option, verify that the Cisco IOS SIP gateway is configured to use Unsolicited
NOTIFY for SIP calls, as shown in the following example:
dial-peer voice 1 voip
destination-pattern 6700
session protocol sipv2
session target ipv4:10.100.9.6
dtmf-relay sip-notify
codec g711ulaw
no vad
Cisco Unity Express 2.3 Command Reference
OL-10351-02
71
D
dtmf-relay
Configure more than one option for transferring DTMF signals. The order in which you configure the
options determines their order of preference. To configure more than one signal option, specify them
using a single dtmf-relay command.
Table 2 shows the various option combinations, the remote end capability, and the signaling option for
incoming and outgoing DTMF signals.
Table 2
DTMF Relay Option Combinations
Cisco Unity Express
Configuration
Option Supported at
Remote End
Option Used for
Option Used for
Incoming DTMF to Cisco Outgoing DTMF from
Unity Express
Cisco Unity Express
sub-notify
—
sub-notify
no DTMF
info
—
no DTMF
info
rtp-nte
rtp-nte
rtp-nte
rtp-nte
sip-notify
sip-notify
sip-notify
sip-notify
1
sip-notify1
sip-notify, rtp-nte
rtp-nte, sip-notify
sip-notify
sip-notify, rtp-nte
rtp-nte
rtp-nte
rtp-nte
sip-notify, info
sip-notify
sip-notify
sip-notify
no DTMF
info
sip-notify
sip-notify
sub-notify
sub-notify
rtp-nte
rtp-nte
sip-notify
sip-notify
no DTMF
info
sip-notify, info
no support
sip-notify, sub-notify
sip-notify
sip-notify, sub-notify
no support
sip-notify, rtp-nte, info
rtp-nte
sip-notify, rtp-nte, info
sip-notify
2
2
2
sip-notify, rtp-nte, info
no support
sip-notify, rtp-nte,
sub-notify
rtp-nte
rtp-nte
rtp-nte
sip-notify, rtp-nte,
sub-notify
sip-notify
sip-notify
sip-notify
sip-notify, rtp-nte,
sub-notify
no support2
sub-notify
no DTMF
sub-notify, info
—
sub-notify
info
rtp-nte, sub-notify
rtp-nte
rtp-nte
rtp-nte
sub-notify
no DTMF
rtp-nte
rtp-nte
no DTMF
info
rtp-nte, sub-notify
no support
rtp-nte, info
rtp-nte
2
2
rtp-nte, info
no support
sip-notify, rtp-nte,
sub-notify, info
sip-notify, rtp-nte
sip-notify
sip-notify
sip-notify, rtp-nte,
sub-notify, info
rtp-nte
rtp-nte
rtp-nte
sip-notify, rtp-nte,
sub-notify, info
no support2
sub-notify
info
1. For incoming call. For outgoing call, the remote end decides between rtp-nte and sip-notify.
2. No support for rtp-nte and sip-notify.
Cisco Unity Express 2.3 Command Reference
72
OL-10351-02
D
dtmf-relay
Examples
The following example configures the options sip-notify and rtp-nte for handling DTMF signals.
se-10-0-0-0# config t
se-10-0-0-0(config)# ccn subsystem sip
se-10-0-0-0(config-sip)# dtmf-relay sip-notify rtp-nte
se-10-0-0-0(config-sip)# end
se-10-0-0-0(config)# end
se-10-0-0-0#
Related Commands
Command
Description
ccn subsystem sip
Enters SIP configuration mode.
mwi sip
Sets the MWI notification mechanism used by Cisco Unity
Express.
show ccn sip subscription mwi
Displays the active MWI subscriptions.
show ccn subsystem sip
Displays the DTMF relay mechanism.
transfer-mode
Sets the transfer mode used by Cisco Unity Express for SIP calls.
Cisco Unity Express 2.3 Command Reference
OL-10351-02
73
D
dtmf-relay
Cisco Unity Express 2.3 Command Reference
74
OL-10351-02