SPECTACLE BLIND – SPADE - SPACER ARAMCO RJ 600 – 900 - 1500 Class RJ 600 Diameter (inches) A B C D F G H J T V Gasket ring no. mm 110 145 175 240 300 355 415 455 510 575 635 685 750 920 mm mm 190 215 245 285 315 360 385 410 450 480 515 545 580 675 mm 180 220 285 370 430 520 570 615 700 755 825 885 950 1145 mm 25 40 40 40 40 40 40 40 50 50 50 50 50 50 mm 10 12 12 15 20 25 25 25 30 40 40 45 50 50 mm 2" 3" 4" 6" 8" 10" 12" 14" 16" OD 18" OD 20" OD 22" OD 24" mm 6 6 6 8 12 12 15 20 20 25 25 30 30 30 mm 28 30 35 43 51 58 65 70 76 85 95 101 112 134 mm 12 16 16 20 20 20 20 24 24 24 32 R23 R31 R37 R45 R49 R53 R57 R61 R65 R69 R73 R81 R77 R95 30" OD A spec ific by purc hase orde r See note 3 Unit weight spade Unit w eight spacer kg 2 5 7 16 29 47 71 91 122 174 240 297 393 705 kg 2 4 5 9 16 22 32 43 52 74 89 110 151 245 Unit weight spade Unit weight spacer kg 3 5 8 17 33 58 83 124 167 239 308 526 kg 3 4 5 11 19 30 52 62 81 115 139 225 Unit weight spade Unit weight spacer kg 3 7 12 23 49 77 129 178 246 336 407 711 kg 3 6 8 17 35 47 71 98 127 181 201 329 Unit weight spectacle kg 4 7 11 25 45 69 103 134 174 248 329 407 544 950 Class RJ 900 Diameter (inches) 2" 3" 4" 6" 8" 10" 12" 14" OD OD 16" 18" OD 20" 24" A B C D F G H J T V Gasket ring no. mm 125 155 180 240 310 360 420 465 525 595 650 770 mm mm 215 230 255 300 345 380 415 430 460 500 535 630 mm 230 255 305 395 485 560 620 655 720 800 870 1055 mm 35 40 40 40 40 40 40 40 50 50 50 50 mm 12 15 15 20 25 25 30 40 40 45 50 65 mm mm 6 6 6 8 12 12 15 20 20 25 25 30 mm 31 36 40 49 58 67 76 88 97 110 118 141 mm 12 15 15 20 20 20 25 25 25 R24 R31 R37 R45 R49 R53 R57 R62 R66 R70 R74 R78 A spec ific by purc hase orde r See note 3 Unit weight spectacle kg 5 9 14 28 52 88 135 186 248 354 447 751 OD RJ 1500 Class Diameter (inches) 2" 3" 4" 6" 8" 10" 12" 14" 16" OD 18" OD 20" 24" OD A B C D F G H J T V Gasket ring no. mm 125 170 195 250 315 370 440 490 545 615 675 795 mm mm 215 240 265 305 350 400 445 485 520 565 600 690 mm 230 280 325 405 495 600 685 760 840 925 1000 1180 mm 35 40 40 40 40 40 40 40 50 50 50 50 mm 15 20 25 25 35 40 45 50 50 65 65 75 mm mm 6 8 8 12 15 20 25 25 25 30 40 40 mm 36 44 49 58 77 88 106 117 131 144 154 182 mm 12 12 16 20 20 20 25 25 25 32 R24 R35 R39 R46 R50 R54 R58 R63 R67 R71 R75 R79 A spec ific by purc hase orde r See note 3 Unit weight spectacle kg 5 13 20 30 84 124 200 276 373 517 608 1040 Notes: 1) Spectacle plates, blinds and spacers are to be made from A105 or equal with specified minimum yield strength of 248.2 MPA. 2) To obtain the maximum P/SE ratio thickness “T” is calculated per ASME B31.3 par 304.5.3 with: P Mpa SE Mpa Class 600 10.34 116.5 Class 900 15.5 116.5 Class 1500 28.5 116.5 Flange material is ASME B16.5 material group no.1. 3) Tolerances: diameters “A” & “B”: +3 mm –3 mm thickness “T”: +1,5 mm -0,25 mm For dimensions and tolerances of ring joint grooves and rings see ASME B16.20 latest edition. 4) Lifting eye is to be formed from the steelrod of composition similar to that of the plate. Commercial standars eyebolt may be used if they have the required dimension and material composition. 5) Welding shall be 100% full penetration by a procedure to be approved before fabrication. 6) Edges of blinds to be free from rough burn finish and burrs. La Meccanica Padana Srl - Via RISCASSI 1/A - 29010 San Nicolo` (PIACENZA) - ITALY - www.meccanicapadana.com Tel: 0039-0523-762020(4 lines) - Fax: 0039-0523-762016 / 762856 / 760302 - meccanica@meccanicapadana.com