Product Code: D71 M83925
02620581-5
805670024239
11.5 ft steel round offset
umbrella WITH NEW BASE
IMPORTANT
SEARS INSISTS ON THE HIGHEST STANDARDS OF
FURNITURE. EACH PIECE HAS BEEN CAREFULLY
INSPECTED BEFORE SHIPMENT.
IN CASE OF PROBLEM, DO NOT RETURN TO THE
STORE, CALL YOTRIO CORPORATION AT PHONE#
1-866-905-4107 BETWEEN THE HOURS OF
8:30 AM TO 5:00 PM PST, MONDAY THROUGH
FRIDAY, FOR ANY QUESTIONS OR PROBLEM YOU
MAY HAVE.
1
11.5′ Round Offset Umbrella Assembly Instruction
PARTS LIST
PARTS
NO.
QTY
A
1 PC
Lower Bracket
B
1 PC
Upper Bracket
C
1 PC
Base Tube
D
4 PCS
M8x20mm Bolts
E
4 PCS
Flat Washer
F
1 PC
Knob
G
1 PC
Tube Rim
H
1 PC
Metal Sheet
I
1 PC
Sunshade
J
1 PC
Wrench
K
4 PCS
Corner Connector
L
2 PCS
Side Panel L
M
2 PCS
Side Panel M
N
1 PC
Sand Bag
DESCRIPTION
NAME
1
11.5′ Round Offset Umbrella Assembly Instruction
PARTS LIST
PARTS
NO.
QTY
O
2 PCS
Upper Base Cover O
P
2 PCS
Support Tube Rim
Q
1 PC
DESCRIPTION
NAME
Upper Base Cover Q
2
11.5′ Round Offset Umbrella Assembly Instruction
Step 01:
Place upper bracket (B) onto lower bracket (A) as shown.
Step 02:
Line up the bolt holes on the Base Tube (C) with the corresponding bolt holes on the
two brackets. Screw the M8*20mm Bolts (D) on with Flat Washers (E) by using
Wrench (J) to ensure that the screws tightened.
Step 03:
Insert Corner Connectors (K) into the four ends of the assembled brackets.
3
11.5′ Round Offset Umbrella Assembly Instruction
Step 04:
Slide Side Panels (M) downward between Corner Connectors (K).
Step 05:
1) Slide Side Panels (L) downward between Corner Connectors (K).
2) Assemble the two pieces of the Support Tube Rim (P) together.
3) Put the assembled Support Tube Rims (P) in the right place as the picture shows.
K
Step 06:
Place Sand Bag (N) into the umbrella base as the picture shows.
4
11.5′ Round Offset Umbrella Assembly Instruction
Step 07:
1) Pull open the velcro pouch to allow sand to be filled. For proper stability of your
offset umbrella, the recommended minimum weight of the sand to be placed into
each sand bag is 110lbs for a total of 220lbs.
2) After filling with sand only, close the pouch and insure the velcro is sealed. Lock
the two sections of Sand Bag (N) together.
Step 08:
1) Check the locker first to make sure it is at the right position as the picture shows
2&3) Assemble Upper Base Cover (O) with the base side panels as the picture shows.
4) Make sure the upper base cover is placed properly for easy locking.
5
11.5′ Round Offset Umbrella Assembly Instruction
Step 09:
1&2) Use the end side of Wrench (J) to lock all the 12 locks clockwise.
3) Assemble Upper Base Cover (Q) with the assembled base.
Step 10:
1) Affix the Metal Sheet (H) to Base Tube (C) and rotate by using Knob (F).
2) Put Tube Rim (G) onto the Base Tube (C).
6
11.5′ Round Offset Umbrella Assembly Instruction
Step 11:
Insert the stem of the Sunshade (I) into the Base Tube (C), then tighten the
Knob (K) clockwise.
Step 12:
Place hand into umbrella crank handle (as shown), squeeze the trigger to unlock,
slide umbrella crank handle upward until it is fully extended and stops.
Step 13:
Remove the “Z” shape crank, then insert it into the hole in stem, turn the “Z”
shape crank clockwise to fully unfold the umbrella.
7
11.5′ Round Offset Umbrella Assembly Instruction
Step 14:
Pull out the “Z” shape crank and place hand chain into umbrella crank handle．　The umbrella canopy can be adjusted to different positions by moving the umbrella
crank handle downward (as shown).
Step 15:
The umbrella is able to turn up to 360 degrees by pressing down the locking
mechanism (as shown) . To fix the umbrella at a desired position, simply release
the lock.
Step 16:
Insert the crank into the hole in stem and turn it counterclockwise to fold the canopy.
Then pull out the crank and fix it into umbrella crank handle. Slide umbrella crank
handle downward until it is fully folded.
See our extensive assortment of outdoor living products on-line at www.sears.com and
www. kmart.com.
8