LED TAPE LIGHT
HIGH OUTPUT, RGB COLOR CHANGING,
& STANDARD
committed to
IP65
2008
GREEN
IP65
Illuminating the future
LED High Output
Tape Light
The high-output linear tape light is designed for installation in discreet locations or hard-to-access shelves and corners. The fixture is
commonly used for cove lighting, in display or kitchen cabinets, within book shelves or desktops – or in any architectural niche that
requires a hidden, dramatic light source. It is also an ideal lighting solution for trade show displays and exhibits. High Output LED
tape light has four times the light output using only three times the energy of our standard tape, and is a perfect solution for your
LED linear lighting needs. This flexible LED light source is a
durable silicone encapsulated tape, ETL Listed
for Wet Location applications and
IP65 rated.
IP65
2008
IP65
F eatures
• Separable every 12" - easily disconnected & connected
without soldering.
• Flexible - easy solderless installation with 12" and 4"
sections.
• Pre-applied 3M™ Tape or clips for mounting
• Field cuttable - every 4" or 6 LEDs
• 64 Watts per roll - over 4W per foot
• 288 LED’s per roll - 18 LEDs per foot
• 120º beam angle
• 205 lumens per foot
• Maximum run - 1 roll (16')
• Title 24 Compliant
• ETL Wet Label Listed
• Dimmable with Dimmable Power Supply
LED High Output Tape Light
NUTP2-16LED(color) 16' Roll (Sixteen 12" connected & sealed sections)
NUTP2-LED(color)/1212" Section with male & female ends
NUTP2-LED(color)/4 4" Section with male & female ends
Color:
3000K Warm White (30), 4200K Cool White (42),
Blue (B), Green (G), Red (R), Yellow (Y)
Dimensions: W: 9/16" H: 1/16"
1/16"
4" Section
9/16"
12" Section
2
LED Tape Light
LED High Output Tape Light
Accessories
Shrink Wrap Tube
NATL-400
Pack of 5
Clear Acrylic Mounting Clips
4' Aluminum Channel
NATHR-685
NATHR-680
Pack of 15
Aluminum
Description: Used to seal
connection made in the field.
Necessary to maintain ETL Wet
Listing. Two shrink wrap tubes are
included with every Tape Light roll
and section.
Description: Used in conjunction
with adhesive backing to attach
Tape Light to a surface. Pack of
15 clear acrylic mounting clips are
included with every High Output
Tape Light roll.
Description: Used to mount Tape
Light to various surfaces. Tape
Light snaps into the channel. Field
cuttable. Recommended for most
installations.
End Cap
Power Line Interconnector
NATL-403
NAHO-609
Power Line Interconnector with
On/Off Switch
Description: Used to cover open
end of High Output Tape Light.
Description: To connect any High
Output Tape Light run to a driver.
(1) NAHO-609 is included with
every High Output Tape Light roll.
NAHO-611
Interconnection Cables
"Y" Splitter Cable
"X" Splitter Cable
NAHO-602
NAHO-606
NAHO-618
NAHO-636
NAHO-672
NAHO-600
NAHO-601
Description: Allows spliting the
High Output Tape light from a run
or driver, into two separate runs.
Description: Allows splitting High
Output Tape Light from a run or
driver, into three separate runs.
Class II LED Driver
Dimmable Class II Remote
Hardwire Magnetic Power
Supply
2" Cable
6" Cable
18" Cable
36" Cable
72" Cable
12" Cable
11" Cable
Description: To allow individual
switching on any High Output Tape
Light run, and connect the LED
tape light run to an LED driver.
Description: The interconnection cable allows easy linking of two
High Output Tape Lights sections. Cables are flexible and can be
moved in any direction, or be joined together for custom lengths.
Class II LED Driver
NATL-530HW
NATL-560HW
30W
60W
NATL-5100
100W
Voltage: 24V DC
NMT-60/24C2
NMT-96/24C2
Voltage: 24V DC
Input Wire: 6' Cord and Plug
Input Wire: 4" Input Wire
Output Wire: 3-1/4" Wire
Output Wire: 3-1/4" Wire
Hardwiring: Cable can be cut to be
hardwired, requires NUSP-JBox for
hardwiring.
Voltage: 24V DC
Power Line Connector
Junction Box for Hard Wiring
NALTL-10
NALTL-30
NUSP-JBox
Requires: NUSP-JBox for hard
wiring
60W
96W
Cable Length: 10 Foot incl.
(30' Cable ordered separately)
Note: Convert to plug-in driver with NRA-6035
Direct Plug-In Driver
NATL-524
NATL-545
24W
45W
10' Cable
30’ Cable
Description: To be used with NMT96/24C2 and NMT-60/24C2 Class
II LED Driver. NALTL-10 is included
with NMT-60/24C2 and
NMT-96/24C2.
Voltage: 24V DC
Cable Length: 6 Feet
Flexible Extension Cord
Flexible Power Cord
NRA-125/6
NRA-125/12
NRA-125/18
NRA-125/72
NRA-6035W/6
NRA-6035W/10
6" Cable
12" Cable
18" Cable
72" Cable
Description: Used to extend length between NUSP-JBox and NATL530HW or NATL-560HW. Can be joined together to create custom
lengths.
Description: To be used with
NATL-530HW, NATL-560HW, or
NATL-5100 Drivers. Capable of
feeding two separate LED Drivers.
Accepts Romex® or flex.
6' Cable
10' Cable
Description: Used to convert
NATL-530HW or
NATL-560HW into a direct plug-in
driver.
*Note: All drivers require NAHO-609 OR NAHO-611 power line interconnector to connect to tape.
LED Tape Light
3
RGB Color Changing
LED Tape Light
RGB LED Tape Light from Nora Lighting is a perfect solution for applications that require a concealed linear lighting system and consistent smooth transitions of colors. It comes in a 16' roll that consists of sixteen 12" sections linked together. The silicone encapsulated
tape can also be cut every 6" and it does not affect circuit (shrink wrap tube included to conceal the cut). The energy efficient RGB
LED Tape light contains 9 LEDs at 2.5W power consumption per foot; 192 LEDs at 40W per roll. It is available with 3 in 1 SMD LEDs
and 120° viewing angle. Maximum run is 2 rolls or 32'. It is extremely durable with operating temperatures of -25ºC to 60ºC (-13ºF to
140ºF). Change the color, the intensity of a color or select an auto changing fade or strobe at the press of a button.
R
G
B
F e at u r e s
IP65
• Separable every 12" - easily disconnected & connected without
soldering.
• 40 Watts per roll - 2.5W per foot
IP65
• Primary colors - Red, Green, Blue and several colors of the visual
spectrum can be selected & programmed.
• Synchronization- Multiple RGB runs can be synchronized to
change simultaneously.
• 192 LED’s per roll - 12 LED per foot.
• Operating temperatures - 25˚C to 60˚C (-13ºF to 140ºF).
• Maximum run - 2 rolls (32').
RGB Color Changing LED Tape Light
NUTP3-16LEDRGB 16' Roll (Sixteen 12” connected & sealed sections)
NUTP3-LEDRGB/12 12" Section with male & female ends
NUTP3-LEDRGB/6 6" Section with male & female ends
Dimensions: W: 9/16" H: 1/16"
1/16"
6" Section
9/16"
12" Section
Driver
Two Low Voltage wires for
synchronization
Driver
NARGB-760
Controller
NARGB-760
Controller
Note: Each RGB Tape Light run requires a driver, controller, power line interconnector and tape.
4
LED Tape Light
32' Tape Light
Power Line
Interconnector
32' Tape Light
LED RGB Tape Light
Accessories
Shrink Wrap Tube
NATL-400
Pack of 5
Clear Acrylic Mounting Clips
4’ Aluminum Channel
NATHR-685
NATHR-680
Pack of 15
Aluminum
Description: Used to seal
connection made in the field.
Necessary to maintain ETL Wet
Listing. Two shrink wrap tubes are
included with every Tape Light roll
and section.
Description: Used in conjunction
with adhesive backing to attach
Tape Light to a surface. Pack of
15 clear acrylic mounting clips
are included with every RGB Tape
Light roll.
Description: Used to mount RGB
Tape Light to various surfaces. RGB
Tape Light snaps into the channel.
Field cuttable..
End Cap
Power Line Interconnector
Interconnection Cables
NATL-403
NARGB-710
Description: Used to cover open
end of RGB Tape Light.
Description: To connect an RGB
controller.
NARGB-702
NARGB-706
NARGB-718
NARGB-736
NARGB-772
12” Cable
Note: (1) NARGB-710 is included
with every RGB Tape Light roll. Use
interconnection cables to increase
length.
Description: The interconnection cable allows easy linking of 2
RGB Tape Lights sections. Cables are flexible and can be moved
in any direction, or be joined together for custom lengths.
“Y” Splitter Cable
“X” Splitter Cable
Direct Plug-In Driver
NARGB-700
NARGB-701
Description: Allows splitting the
RGB Tape Light from a run or
driver, into two separate runs.
Description: Allows splitting the
RGB Tape Light from a run or
driver, into three separate runs.
NATL-524
NATL-545
Class II LED Driver
Class II LED Driver
NATL-530HW
NATL-560HW
30W
60W
NATL-5100
2” Cable
6” Cable
18” Cable
36” Cable
72” Cable
24W
45W
Voltage: 24V DC
Cable Length: 6 Feet
Class II Remote Hardwire
Magnetic Power Supply
100W
Voltage: 24V DC
Input Wire: 6' Cord and Plug
NMT-60/24C2
NMT-96/24C2
Input Wire: 4" Input Wire
Output Wire: 3-1/4" Wire
Voltage: 24V DC
Output Wire: 3-1/4" Wire
Hardwiring: Cable can be cut to be
hardwired, requires NUSP-JBox for
hardwiring.
Cable Length: 10 Foot incl.
(30' Cable ordered separately)
Requires: NUSP-JBox for hard
wiring
Voltage: 24V DC
Note: Convert to plug-in driver with NRA-6035
Note: RGB LED Tape cannot be dimmed. The controller with hand
held remote allows 3 brightness levels.
Junction Box for Hard Wiring
Flexible Extension Cord
Flexible Power Cord
NUSP-JBox
NRA-125/6
NRA-125/12
NRA-125/18
NRA-125/72
NRA-6035W/6
NRA-6035W/10
Description: To be used with
NATL-530HW, NATL-560HW, or
NATL-5100 Drivers. Capable of
feeding two separate LED Drivers.
Accepts Romex® or flex.
60W
96W
6" Cable
12" Cable
18" Cable
72" Cable
6’ Cable
10’ Cable
Description: Used to convert
NATL-530HW or
NATL-560HW into a direct plug-in
driver.
Description: Used to extend length between NUSP-JBox and NATL530HW or NATL-560HW. Can be joined together to create custom
lengths.
Power Line Connector
RGB Controller
Hand Held Remote
NALTL-10
NALTL-30
NARGB-760
NARGB-761
Description: 360W Max. A
controller is required for each
RGB LED Tape Light run. It installs
between the driver and the power
line interconnector. The controller
can be used to toggle between
colors or changing modes.
Description: For remote control
of RGB Controller up to 22’ away
(must be in direct view line of RGB
controller to work correctly). Used
to program RGB Tape Light run to
certain color configurations.
10' Cable
30’ Cable
Description: To be used with NMT96/24C2 and NMT-60/24C2 Class
II LED Driver. NALTL-10 is included
with NMT-60/24C2 and
NMT-96/24C2.
Note: Requires the
NARGB-710 power line interconnector to connect to RGB tape.
Key Selections: Brightness, Colors, Color Changing - Flash, Strobe, Fade
and Smooth Fade, On/Off
*Note: Each RGB Tape Light run requires a driver, controller, power line interconnector and tape.
To accomplish the RGB color changing, you must use the RGB controller between the Driver and the RGB tape.
LED Tape Light
5
LED Standard
Tape Light
Nora Lighting continues to provide solutions for your LED linear lighting needs by introducing our LED Tape Light.
This energy efficient and very low profile LED tape is great for use in many discreet locations. Only 7/16" wide
and 1/16" thick, our flexible LED light is designed to cast no shadows and boasts a desirable seamless glow.
Installation is easy as your 5 meter (16.6 feet) rolls are separable every 20", each strip can also be cut every
4". Our durable, silicone encapsulated tape, is rated for Wet Location applications and is IP65 rated. The energy
efficient LED tape provides 18 LED’s per foot at
1.5W per foot, 24W per roll. 65 lumens per
foot at 3000K color temperature.
IP65
2008
IP65
F e at u r e s
• Separable every 20" - easily disconnected & connected
without soldering.
• Field cuttable - every 4" or 6 LEDs
• 24 Watts per roll - 1.5W per foot
• Available in 6 colors - Red, Blue, Green, Yellow,
Warm White (3000K), Cool White (4200K).
• 65 Lumens per foot with 3000K CCT
• No UV light or infrared wavelengths
• Easy to install - pre-applied 3M™ tape or 15 acrylic
mounting clips (included with roll/kit). New plastic channels
available for rigidity.
• New 16' roll with 12" sections - available soon!
• Dimmable with Dimmable Power Supply
LED Standard Tape Light
NUTP1-16LED(color) 16.6' Roll (Ten 20" sections)
NUTP1-LED(color)/1212" Section with male & female ends
NUTP1-LED(color)/4 4" Section with male & female ends
NUTP1-16LED30PS 16.6' 3000K Kit including Plug-In Driver
Color Temp.: 3000K Warm White (30), 4200K Cool White (42),
Blue (B), Green (G), Red (R), Yellow (Y)
Dimensions: W: 7/16" H: 1/16"
4" Section
1/16"
7/16"
12" Section
6
LED Tape Light
LED Standard Tape Light
Accessories
Shrink Wrap Tube
NATL-400
Pack of 5
Clear Acrylic Mounting Clips
4’ Plastic Channel
NATL-401
NATL-420B
NATL-420W
Pack of 15
Black
White
Description: Used to seal
connection made in the field.
Necessary to maintain ETL Wet
Listing. Two shrink wrap tubes are
included with every Tape Light roll
and section.
Description: Used in conjunction with
adhesive backing to attach Tape Light
to a surface. Pack of 15 clear acrylic
mounting clips are included with every
Tape Light roll.
End Cap
Power Line Interconnector
NATL-403
NATL-509
Description: Used to cover open
end of High Output Tape Light.
Description: To connect any Tape
Light run to a driver.
(1) NATL-509 is included with every
Tape Light roll.
NATL-511
Interconnection Cables
“Y” Splitter Cable
“X” Splitter Cable
NATL-202
NATL-206
NATL-218
NATL-236
NATL-272
NATL-300
NATL-301
Description: Allows splitting the
Tape Light from a run or driver, into
two separate runs.
Description: Allows splitting the
Tape Light from a run or driver, into
three separate runs
Class II LED Driver
Dimmable Class II Remote
Hardwire Magnetic Power
Supply
2” Cable
6” Cable
18” Cable
36” Cable
72” Cable
9” Cable
Description: Used to mount Tape
Light to various surfaces. Tape
Light snaps into the channel. Field
cuttable. UV protected.
Power Line Interconnector with
On/Off Switch
11” Cable
Description: To allow individual
switching on any Tape Light run,
and connect LED Tape Light run
directly to LED Driver.
Description: The interconnection cable allows easy linking of
two Tape Lights sections. Cables are flexible and can be moved
in any direction, or be joined together for custom lengths.
Class II LED Driver
NATL-530HW
NATL-560HW
30W
60W
NATL-5100
100W
Voltage: 24V DC
NMT-60/24C2
NMT-96/24C2
Voltage: 24V DC
Input Wire: 6' Cord and Plug
Input Wire: 4" Input Wire
Output Wire: 3-1/4" Wire
Output Wire: 3-1/4" Wire
Hardwiring: Cable can be cut to be
hardwired, requires NUSP-JBox for
hardwiring.
Voltage: 24V DC
Power Line Connector
Junction Box for Hard Wiring
NALTL-10
NALTL-30
NUSP-JBox
Requires: NUSP-JBox for hard
wiring
60W
96W
Cable Length: 10 Foot incl.
(30' Cable ordered separately)
Note: Convert to plug-in driver with NRA-6035
Direct Plug-In Driver
NATL-524
NATL-545
24W
45W
10' Cable
30’ Cable
Description: To be used with NMT96/24C2 and NMT-60/24C2 Class
II LED Driver. NALTL-10 is included
with NMT-60/24C2 and
NMT-96/24C2.
Voltage: 24V DC
Cable Length: 6 Feet
Flexible Extension Cord
Flexible Power Cord
NRA-125/6
NRA-125/12
NRA-125/18
NRA-125/72
NRA-6035W/6
NRA-6035W/10
6" Cable
12" Cable
18" Cable
72" Cable
Description: Used to extend length between NUSP-JBox and NATL530HW or NATL-560HW. Can be joined together to create custom
lengths.
Description: To be used with
NATL-530HW, NATL-560HW, or
NATL-5100 Drivers. Capable of
feeding two separate LED Drivers.
Accepts Romex® or flex.
6' Cable
10' Cable
Description: Used to convert
NATL-530HW or
NATL-560HW into a direct plug-in
driver.
*Note: All drivers require NATL-509 or NATL-511 power line interconnector to connect to tape.
LED Tape Light
7
LED TAPE LIGHT
6505 Gayhart St., Commerce, CA 90040
Tel. 800.686.6672 | Fax 800.500.9955 | www.noralighting.com
5G
ML-LEDTAPE1210