Chapter 9: Dimming actuators/control units
9.5 Control unit, 3-gang
Control unit 1-10 V REG-K, 3-gang
Art. No. 647129
Control unit 1-10 V REG-K, 3-gangChapter 9:Dimming actuators/control unitsArt. No.647129As at 01/019.5Control unit, 3-gang
Control unit 1-10 V REG-K, 3-gang
1. Function
The control unit is used for the brightness control of
3 lighting circuits. The following devices can be controlled:
– Electronic ballasts with 1-10 V interface
– Electronic LV halogen transformers
with 1-10 V interface.
A floating switch contact is used for switching off the
connected devices. The switch outputs can also be
used to switch additional lighting circuits.
Article No.
647129
auto
uell
man
3
2
EIB
bus
insta it 1-10V
®
inhe
uere fach
Ste -K / 3G
RE
29
647150 Hz
AC
1
230V
"Auto/manual" selector switch:
Table of Contents
1.
Function
1
2.
Commissioning
1
3.
Technical Data
2
4.
Settings in the EIB Tool Software (ETS)
3
5.
Application overview
3
In the "Auto" position, the outputs are controlled by the
assigned sensors via the bus cable.
In the "Manual" position, the outputs can be switched
via the operator buttons on the device.
2. Commissioning
– Connect the power supply AC 230 V and bus voltage
Connect the outputs
– Check the function of the outputs:
Set the selector switch to the "Manual" position.
Switch the loads by pressing the operator buttons
| Dimming is not possible via the operator butNote:
tons on the device.
– Check the bus connection:
Set the selector switch to the "Auto" position.
If the bus voltage fails, all the status displays flash.
– Define the functional characteristics by assigning
parameters and downloading the associated application software with the help of ETS.
Notes about the programming:
Assigning the physical address:
– Set the selector switch to the "Auto" position to assign the physical address.
– Press all 3 operator buttons simultaneously. The
LED at output 1 flashes to indicate that the device
is ready for programming.
As at 01/01
1
Chapter 9: Dimming actuators/control units
9.5 Control unit, 3-gang
Control unit 1-10 V REG-K, 3-gang
Art. No. 647129
Circuit diagram:
3. Technical Data
Electrical data
Power supply:
A
AC 230 V, 50 Hz and
INSTABUS EIB,
DC 24 V (+ 6 / - 3 V)
5 VA
maximum 10 W
10 A, cos ϕ = 0.6
Power consumption:
Leakage loss:
Nominal current:
Operating data
Control outputs 1-10 V: max. 50 mA current sink
Contact rating:
16 A, cos ϕ = 1, 250 V
(180,000 switching cycles)
Contact endurance:
125,000 switching cycles
At the following loads:
Incandescent lamps:
2000 W
LV halogen lamps with 2600 W
electronic transformer:
Fluorescent lamps
with electronic ballast: 60 x 18 W
30 x 36 W
18 x 58 W
Contact endurance:
100,000 switching cycles
At the following load:
Halogen lamps 230 V: 1600 W
Environment
Operation:
0 °C to +45 °C
Storage:
-20 °C to +70 °C
Connection
Cage clamp terminals:
flexible:
1 mm2 to 6 mm2
solid:
1.5 mm2 to 10 mm2
Dimensions
Size:
6 modules
(approx. 108 mm)
As at 01/01
230 V 50 Hz
L
N
B
C
D
L
1
3
9
11 13 15 17 19
auto
K
N
EVG
1-10 V
+
manuell
-
instabusEIB
®
E
Steuereinheit 1-10V
REG-K / 3-fach
1
6471 29
2
3
AC 230V 50 Hz
F
10
12 14 16 18 20
-
+
I
INSTABUS EIB
- +
- +
H
G
J
A
Make contact, output 1
B
Make contact, output 2
C
Make contact, output 3
D
Connection of an electronic ballast
E
Status display
F
Operator buttons:
Manual operation of the outputs in the "Manual"
position of the selector switch (only ON and OFF)
G
1-10 V, output 3
H
1-10 V, output 2
I
1-10 V, output 1
J
Further connection
K
Selector switch
– top/"Auto": normal mode
– bottom/"Manual": manual operation via operator buttons
2
Chapter 9: Dimming actuators/control units
9.5 Control unit, 3-gang
Control unit 1-10 V REG-K, 3-gang
Art. No. 647129
4. Settings in the EIB Tool Software (ETS)
Selection in the product database
Manufacturer:
Product family:
Product type:
Program name:
Media type:
Product name:
Order number:
Merten
4.7
Control unit 1-10 V
4.7.01 DIN rail mounted REG-K
Dimming 3271/1
Twisted Pair
Control unit 1-10 V REG-K, 3-gang
647129
5. Application overview
The following application can be selected:
Application
Vers. Function
Dimming 3271/1
1
Behaviour on bus voltage recovery
Switching
– with adjustable starting behaviour
– Memory function (last brightness
value)
– Status feedback of the relay state
via separate status feedback object
Dimming
– with variable dimming speed
Scenes
– 4 scenes for the 3 outputs
As at 01/01
3