TM
Attenuator Type-E
PROFADER
ATTENUATOR
Model number
Low contact resistance
2
P
*A
*B
50
E
Max attenuation
Product type
*A Number of circuit
*B Circuit
*C Stepper Type
Au-plated contact materials.
3 types attenuation circuits
S
*C
-
10kohm
Impedance
Blank: single circuit, 2: Dual circuits
P: Potentiometer, T: Bridged-T, H: Bridged-H
Blank: Non-stepper type (Without clicks), S: Stepper type (With clicks)
Potentiometer, B-T, B-H
High Accuracy
Used a highly precise resistor.
Dimensions
Electrical specifications
Cro ss rece ssed head screws M3
Type-E
0
φ 6 -0.1
E-1
φ 30 ±1
P / CW
2P / CW
P / CCW
2P / CCW
CP600 is a Small variable attenuator of the 16mm-square.
2
2 C
It is made to be almost decrement properties of the BSS-50dB(NHK) Cattenuator.
1
1
Dimentions
22 ±0.2
1
22 ±1
L ±1
C
2
C
1
2
1
C
C
2
1
2
MAX.6
Ci rcuit
L
P
31
Attenuation accuracy
Accuracy of Impedance
Terminal position
[ Number of ci rcuit / Di rection of attenuation ]
2P
49
Attenuation
φ 30 ±1
0
E-2
φ 6 -0.1
Cut off (15kHz)
22 ±0.2
T / CCW
1
22 ±1
L ±1
1
C
C
2
1
C
1
2
C
1
2
C
2
1
T
39
φ 30 ±1
22 ±0.2
H / CCW
1
22 ±1
L ±1
Ci rcuit
L
23
4
H / CW
4
32
1
2H / CW
2H / CCW
4
3
1
2
1
4
1
23
MAX.6
H
52
2H
91
The products and their specifications are subject to change without notice.
TOKYO KO-ON DENPA CO., LTD. www.tkd-corp.com EDF-201506
Terminal position
[ Number of ci rcuit / Di rection of attenuation ]
Voltage proof
Insulation resistance
Input level
Rotational life
Attenuation step
0.5dB or less
1~2dB
3dB or more
Error in step
Less than ±0.05
Less than ±0.1
Less than ±0.2
Max. Attenuation
Less than ±0.1
Less than ±0.2
Less than ±0.4
±2% (Impedance 600ohm), ±5% (other Impedance)
Cut off
80dB Min.
70dB Min.
58dB Min.
Max. Attenuation
50dB
50dB
20dB
Impedance
600ohm
7kohm
7kohm
1 Min. at AC500V
100Mohm or more at DC500V
Max. 0.3W
30,000 Cycles Min. (18cycles/min, Insertion loss: 1dB or less)
Mechanical specifications
Terminal position
[ Number of ci rcuit / Di rection of attenuation ]
2T
65
0
E-3
2
2T / CW
2T / CCW
MAX.6
φ 6 -0.1
Ci rcuit
L
2
C
T / CW
BTS-50dB 0, 2, 4, …(2dB step)…, 30, 32, 34, 37, 42, 50, cut off
2
4
3
4
1
32
Operating angle
Strength of Nut-Attached
Attached Parts
Stopper strength
Push-pull strength
Type-E
(Step angle) x (Number of steps) ±2degrees
100Ncm
M3 screw (Length: Panel thickness + 3~5mm)
50Ncm
50N
General specifications
Temp.range
Relative humidity
Type-E
-10 to +60 degrees C (Operating), -15 to +65 degrees C (Storage)
80%RH (No condensation)
Note
* Solder heat resistance: 350degrees C max, 5sec max, to twice. (Manual soldering only)
* The solder please use the thing of the same composition. (Solder for wire lapping sticks to a terminal.)
Use solder: SN100C (Sn-0.7Cu-0.05Ni-Ge) NIHON SUPERIOR CO.,LTD.
* Cannot use this product for the signal line using phontom-48V.
* This product is an attenuator of the types to change resistance. Therefore, a switching noise may occur.
STANDARD LINEUPS
Order
Number
E-P001
E-P002
E-P003
E-P004
E-P005
E-T001
E-T002
E-T003
E-T004
E-T005
E-T006
E-T007
E-T008
E-T009
E-T010
E-T011
E-T012
E-T013
E-T014
E-T015
E-T016
E-T017
E-T018
Model number
Circuit
P50ES-1kohm
P50ES-50kohm
P50ES-250kohm
P50ES-500kohm
2P50ES-50kohm
P
P
P
P
P x2
T10ES-600ohm
T10ES-600ohm
T20ES-600ohm
T20E-600ohm
T20ES-600ohm
T20E-600ohm
T40ES-600ohm
T40E-600ohm
T42ES-600ohm
T42E-600ohm
T50ES-3kohm
T50E-3kohm
T50ES-600ohm
T50E-600ohm
T50ES-600ohm
T50ES-600ohm
2T50ES-600ohm
2T50E-600ohm
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T
T x2
T x2
Max.
Attenuation
50dB
50dB
50dB
50dB
50dB
10dB
10dB
20dB
20dB
20dB
20dB
40dB
40dB
42dB
42dB
50dB
50dB
50dB
50dB
50dB
50dB
50dB
50dB
Attenuation
types
BTS-50dB
BTS-50dB
BTS-50dB
BTS-50dB
BTS-50dB
1dB x 10
1dB x 10
1dB x 20
1dB x 20
1dB x 20
1dB x 20
2dB x 20
2dB x 20
2dB x 21
2dB x 21
BTS-50dB
BTS-50dB
BTS-50dB
BTS-50dB
5dB x 10
10dB x 5
BTS-50dB
BTS-50dB
Impedance
1kohm
50kohm
250kohm
500kohm
50kohm
600ohm
600ohm
600ohm
600ohm
600ohm
600ohm
600ohm
600ohm
600ohm
600ohm
3kohm
3kohm
600ohm
600ohm
600ohm
600ohm
600ohm
600ohm
Frequency
Range
DC~100kHz
DC~50kHz
DC~15kHz
DC~15kHz
DC~50kHz
DC~500kHz
DC~200kHz
DC~200kHz
DC~200kHz
DC~200kHz
DC~200kHz
DC~150kHz
DC~150kHz
DC~150kHz
DC~150kHz
DC~15kHz
DC~15kHz
DC~20kHz
DC~20kHz
DC~100kHz
DC~100kHz
DC~20kHz
DC~20kHz
1step
angle
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
15degs
30degs
30degs
15degs
15degs
Total Number Stepper
of steps
option
21
With
21
With
21
With
21
With
21
With
10
11
21
21
21
21
20
20
21
21
21
21
21
21
10
5
21
21
With
With
With
With
With
With
With
With
With
With
With
-
Cut off
With
With
With
With
With
With
With
With
With
With
With
With
With
With
With
With
Direction of
attenuation
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CW
CW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
CCW
Dim.
E-1
E-1
E-1
E-1
E-1
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
E-2
Specification Information
Order Number
Circuit
Standard products with a simple number.
POTENTIOMETER
Unbalanced circuit
BRIDGED-T
Insertion loss: 0dB
Constant impedance
Unbalanced circuit
BRIDGED-H
Insertion loss: 0dB
Constant impedance
Balanced circuit
Max. Attenuation
Attenuation types
Impedance
Frequency Range
1
2
1
2
C
C
1
3
2
4
Maximum attenuation without Cut off point.
BTS-50dB: Look at specifications.
Ex) “1dBx10”: 0, 1, …(1dB step)…, 9, 10dB
Total resistance (Potentiometer), Input / Output Impedance (other circuits)
Operating frequency range.
1step angle
The angle to the next decrement point.
Total rotational angle = (Number of steps) x (1step angle)
Determined by the Circuit and Attenuation types.
Total number of contacts = Total number of steps + 1
Stepper option
With: With Clicks
Cut off
Cut off attenuation.
Please see the cut-off attenuation specification.
Direction of attenuation CCW: Attenuation decreases with the clockwise (Up to Signal level).
CW: Attenuation increases with the clockwise (Down to Signal level).
Dimension
Please see the Dimension and Dimension number.
Total Number of steps
Method of ordering
1. Can estimate the standard lineup product only with the order number.
2. In the case of the specifications product which a standard lineup does not have,
there are two ways of estimate methods.
a: Method to change a part of the standard lineup specifications
a-1: Please inform it of the order number and specifications change point.
Modifiable point: Cut off (With / Without), Stepper option (With / Without),
Impedance, Control shaft length
a-2: Examine production possibility with designated specifications before an estimate.
a-3: Inform it of the model number and an estimate.
b: Special order specifications
b-1: Please inform it of specifications of the hope.
(Cannot change the basic electric specifications such as input levels.)
Modifiable point: Cut off (With / Without), Stepper option (With / Without), Impedance,
Control shaft length, Circuit, Max.Attenuation, Attenuation type
b-2: Examine production possibility with designated specifications before an estimate.
b-3: Inform it of the model number and an estimate.
E-H001
E-H002
H50ES-600ohm
H50E-600ohm
H
H
50dB
50dB
BTS-50dB
BTS-50dB
600ohm
600ohm
DC~20kHz
DC~20kHz
15degs
15degs
21
21
With
-
With
With
CCW
CCW
E-3
E-3
*The standard lineups are added or removed without notice.
C