CLEVIS PINS We supply Clevis Pins to ISO 2341B (DIN 1444) which has a crossdrilled hole for R-Pins or Cotter Pins (see pages 18 and 19). Also available are ISO 2341 with grooves for Circlips to DIN 471. When specifying Clevis Pins, it should be noted that the nominal length is the total length from under the head to the end of the pin, but the grip length is from under the head to the inside edge of the hole or groove. This is shown in the table under references L1 and G1. STANDARDS ISO 2341A same as 2341 but without hole ISO 2341 – Circlip (for Circlips to DIN 471) ISO 2341B ISO 2340A ISO 2340B BS 5894 DIN 1433 DIN 1434 DIN 1435 DIN 1436 DIN 1443 DIN 1444 14 20 3.2 4 1.1 11.5 5.5 22 4 4 1.1 13.4 6 16.9 18.9 20.9 22.9 24.9 27.9 32.9 37.9 42.9 47.9 52.9 57.9 62.9 67.9 72.9 77.9 82.9 87.9 92.9 112.9 20 22 24 27 32 37 42 47 52 57 62 67 72 77 82 87 92 112 132 Over 50 mm long ± 0.75 MILD STEEL, ZINC PLATED Headless, without hole STAINLESS A2 Headless, with cross-drilled hole at each end STAINLESS A4 obsolete, replaced by ISO 2341 Headless, with or without hole Similar to ISO 2341 but with smaller diameter head Similar to ISO 2341 but with larger diameter head Similar to ISO 2341 but with larger diameter head Same as ISO 2340 Same as ISO 2341 SIZE RANGE – CLEVIS PINS 12 MATERIALS our stocked programme AVAILABLE TO ORDER < Non-Standard dimensions < Other materials * ALSO AVAILABLE IN INCH SIZES Nominal Diameter ‘d’ Diameter Tolerance Head Diameter ‘H’ Hole Diameter ‘d1’ Head Thickness ‘T’ Circlip Groove ‘C1’ Circlip Groove ‘C2’ Length ‘L2’ min Length ‘G1 Lengths ‘L1’ 10 12 14 16 18 20 22 24 26 28 30 32 35 40 45 50 55 60 65 70 75 80 85 90 95 100 120 140 Length Tolerances E: sales@technifast.co.uk W: www.technifast.co.uk 5 6 8 10 1.6 1.6 1.6 2 0.7 0.8 4.8 5.7 2.9 3.2 L1 – L2 – 1/2 d1 6.7 8.7 10.7 12.7 14.7 16.7 18.7 20.7 22.7 24.7 26.7 28.7 31.7 36.7 41.7 46.7 8 10 12 14 16 18 20 22 24 26 28 31 36 41 46 51 56 Up to 10 mm long ± 0.25 8 h11 14 2 3 0.9 7.6 3.5 11.5 13.5 15.5 17.5 19.5 21.5 23.5 25.5 27.5 30.5 35.5 40.5 45.5 50.5 55.5 60.5 65.5 70.5 75.5 10 12 14 18 3.2 4 1.1 9.6 4.5 20 3.2 4 1.1 11.5 5.5 22 4 4 1.1 13.4 6 13.9 15.9 17.9 19.9 21.9 23.9 25.9 28.9 33.9 38.9 43.9 48.9 53.9 58.9 63.9 68.9 73.9 78.9 83.9 88.9 93.9 12 – 50 mm long ± 0.5 16.9 18.9 20.9 22.9 24.9 27.9 32.9 37.9 42.9 47.9 52.9 57.9 62.9 67.9 72.9 77.9 82.9 87.9 92.9 112.9 20 22 24 27 32 37 42 47 52 57 62 67 72 77 82 87 92 112 132 Over 50 mm long ± 0.75 20