MSD IGNITION TESTER, PN 8998

advertisement
www.msdignition.com
email: msdtech@msdignition.com
AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344
MSD IGNITION TESTER, PN 8998
MSD’s Ignition Tester, PN 8998, will give you a quick way to confirm the operation of your MSD Ignition and Coil.
It will also let you check rev limits, rpm switches and the camshaft sync signal of controls with Individual Cylinder
Management circuits.
The Tester connects easily to a 12 volt source, ground and a trigger wire. The PN 8998 will simulate a trigger signal
through either the points (White) wire or magnetic pickup connector of the ignition. A test plug is supplied that
connects to the coil secondary wire leading to the distributor and ground. When the Tester is turned on, a spark will
jump the gap of the test plug confirming operation of the Ignition and Coil.
The PN 8998 is designed for testing single channel MSD Ignitions such as the 6A, Digital-7 and even the MSD 10.
It can also be used with MSD Timing Controls. For Multi-Channel Ignitions, see page 128.
Note: The Tester, PN 8998, supercedes PN 8995.
General Wiring
Red:
Black:
Connects to switched 12 volt source.
Connects to ground.
Trigger Wires
White: Connects to points or an ignition amplifier output. When this wire is used the Magnetic
Pickup is not (Violet and Green).
Violet and Green: These wires are routed together in one harness and form the magnetic pickup connector.
This connector plugs directly into an MSD Distributor or Crank Trigger. The Violet wire is
positive (+) and the Green wire is negative (-). When this connector is used, the White wire
is not.
Cam Sync
Light Blue and This connector is used to confirm the cam sync signal for use with Individual Cylinder
Green: Management circuit. When the engine runs, it will show “Cam Sync - Sync” for a good
signal “Cam Sync - None” if there is a problem.
Cylinder Select: Push the Program Selection button on top of the PN 8998 to select 4, 6 or 8-cylinder operation.
(There is a toggle switch on the PN 8995 for cylinder selection.)
125
www.msdignition.com
email: msdtech@msdignition.com
AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344
MSD IGNITION TESTER TO MSD 6 SERIES
IGNITION WITH POINTS
MSD IGNITION TESTER TO MSD 7 SERIES
IGNITION WITH MAG PICKUP
126
www.msdignition.com
email: msdtech@msdignition.com
AUTOTRONIC CONTROLS CORPORATION • 1490 HENRY BRENNAN, EL PASO, TEXAS 79936 • (915) 857-5200 • FAX (915) 857-3344
MSD IGNITION TESTER TO MSD 7 SERIES
IGNITION WITH TIMING CONTROL
Note: The Obsoleted PN 8995 Tester will not work
through the magnetic pickup of a timing control.
MSD IGNITION TESTER TO MSD
PROGRAMMABLE DIGITAL-7 IGNITION
CRANK TRIGGER
MAGNETIC
PICKUP
DISTRIBUTOR
COIL WIRE
WHITE
NOT USED
IGNITION
TESTER by
TM
- +
AUTOTRONIC CONTROLS CORPORATION
12120 ESTHER LAMA, SUITE 114, EL PASO, TEXAS 79936
(+)
MAGNETIC
PICKUP
CONNECT
TO
GROUND
DISCONNECT
+
N
RA
O
mable
TM
DIGITAL-7
Program
PROGRAMMER
PN 7550
CK
BLA
MSD
PROGRAMMER
MONITOR
(-)
BATTERY
- +
GE
RED
BLACK
RED
BLACK
CAM
SYNC
OR
ENTER
RED
PN 8996
TEST
PLUG
COIL
NEXT
LAUNCH
REV LIMITER
TM
PN 7550
AUTOTRONIC CONTROLS CORPORATION
1490 HENRY BRENNAN DR., EL PASO, TX 79936
TO 12 VOLTS
127
Download