Package Drawing
Designator: K
Type: 4-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9010)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
45°
5.21
+0.08
–0.05
1.55 ±0.05
D
Mold Ejector
Pin Indent
3.43
+0.08
–0.05
45°
1
2
3
Branded
Face
4
2.16 MAX
0.84 REF
A
+0.07
0.41
–0.05
0.38
+0.06
–0.03
NNNN
YYWW
1.27 NOM
1
14.73 ±0.51
Standard Branding Reference View
C
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
A
Dambar removal protrusion (8X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth, 0.43 REF
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: K - TL/TS
Type: 4-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9010)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45°
B
5.21
+0.08
–0.05
1.55 ±0.05
D
Mold Ejector
Pin Indent
+0.08
3.43
–0.05
Branded
Face
1
2.41 ±0.13
2
3
A
4
A
0.41
+0.07
–0.05
1.27 NOM
45°
NNNN
YYWW
A
Dambar removal protrusion (8X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth, 0.43 mm REF
E
Reference land pattern layout;
All pads a minimum of 0.20 mm from all adjacent pads;
adjust as necessary to meet application process
requirements and PCB layout tolerances
1
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
0.84 REF
0.38
+0.06
–0.03
0.00º
0.10º
0.97
0.51 MIN
1.57
8°
0°
1.27
E
PCB Layout Reference View
Detail A
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: K - TW
Type: 4-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9010)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45°
B
5.21
+0.08
–0.05
1.55 ±0.05
D
3.43
Mold Ejector
Pin Indent
+0.08
–0.05
Branded
Face
1
2.41 ±0.13
2
3
A
4
A
0.41
+0.07
–0.05
1.27 NOM
45°
NNNN
YYWW
A
1
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
0.65
1.05
0.84 REF
0.38
+0.06
–0.03
0.00
0.15
Dambar removal protrusion (8X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth, 0.43 mm REF
E
Reference land pattern layout;
all pads a minimum of 0.20 mm from all adjacent pads;
adjust as necessary to meet application process
requirements and PCB layout tolerances
0.97
0.83 ±0.18
1.57
0°
8º
1.27
E
PCB Layout Reference View
Detail A
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: KA
Type: 5-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9051)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
6.38
+0.08
–0.05
1.55 ±0.05
D
Mold Ejector
Pin Indent
+0.08
4.52
–0.05
Branded
Face
1
2
3
4
45°
5
0.84 REF
2.11 MAX
0.51 REF
A
0.41
+0.05
0.43
–0.07
+0.03
–0.06
NNNN
YYWW
1
14.73 ±0.51
1.27 NOM
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
A
Dambar removal protrusion (10X)
B
Gate burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth 0.42 mm REF
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Rev. 2
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: KA - TL/TS
Type: 5-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9051)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
6.38
1.55 ±0.05
+0.08
–0.05
D
Mold Ejector
Pin Indent
4.52
+0.08
–0.05
Branded
Face
1
2.41 ±0.13
2
3
4
A
5
0.41
0.43
+0.05
–0.07
45°
+0.03
–0.06
0.51 MIN
8º
0º
1.27 NOM
0.051 MAX
0.10 MAX
SEATING PLANE
NNNN
YYWW
A
Dambar removal protrusion (10X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth 0.42 mm REF
1
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: KB
Type: 3-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9009)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45°
B
+0.08
5.21
–0.05
1.55 ±0.05
D
Mold Ejector
Pin Indent
3.43
+0.08
–0.05
45°
Branded
Face
2.16 MAX
0.84 REF
0.51 REF
A
1
2
3
0.51
+0.07
–0.05
0.38
+0.06
–0.03
1.90 NOM
NNNN
YYWW
14.73 ±0.51
1
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
A
Dambar removal protrusion (6X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Active area depth = 0.43 REF
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: KE
Type: 4-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9203)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
25°
6.10
+0.08
–0.05
1.60
45° (2X)
+0.08
–0.05
E
0.61 REF (2X)
4.95
+0.08
–0.05
Branded
Face
0.89 MAX
1
2
3
4
A
0.41
6.00 REF
+0.08
–0.05
1.09 REF
0.25
1.27 NOM
13.92 ±0.05
0.71
+0.08
–0.05
NNNN
YYWW
+0.08
–0.05
1
C
1.75 NOM
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
6.66 REF
1.09 REF
A
Dambar removal protrusion (16X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Molded Lead Bar
E
Active Area Depth, 0.43 mm REF
0.89 MAX
1.60
+0.08
–0.05
D
0.30 REF (3X)
6.10
+0.08
–0.05
1.60
+0.08
–0.05
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: KN
Type: 4-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9015)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45°
B
+0.08
5.21 –0.05
1.55 ±0.05
D
Mold Ejector
Pin Indent
+0.08
3.43 –0.05
Branded
Face
1
2
3
45°
4
2.16 MAX
0.84 REF
A
6.00 REF
+0.07
0.41 –0.05
1.27 NOM
+0.06
0.38 –0.03
NNNN
YYWW
+0.08
1.03 –0.05
14.74 ±0.51
3.19 NOM
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
8.12 REF
A
Dambar removal protrusion (8X)
B
Gate and tie bar burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth 0.43 mm REF
0.38 REF
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: KT
Type: 4-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9202)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
10°
+0.08
1.00 –0.05
+0.08
5.21 –0.05
E
Mold Ejector
Pin Indent
+0.08
3.43 –0.05
Branded
Face
0.89 MAX
1
2
3
4
A
0.54 REF
+0.08
0.20 –0.05
+0.08
0.41 –0.05
NNNN
YYWW
12.14 ±0.05
1.27 NOM
C
Standard Branding Reference View
N = Device part number
Y = Last two digits of year of manufacture
W = Week of manufacture
0.54 REF
0.89 MAX
Mold Ejector
Pin Indent
+0.08
1.50 –0.05
D
+0.08
1.00 –0.05
+0.08
5.21 –0.05
A
Dambar removal protrusion (16X)
B
Gate and tie burr area
C
Branding scale and appearance at supplier discretion
D
Molded Lead Bar
E
Active Area Depth, 0.37 mm REF
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Rev.1
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: U
Type: 3-pin SIP
For Reference Only – Not for Tooling Use
(Reference DWG-9063)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
+0.08
4.57 –0.05
1.55 ±0.05
C
Mold Ejector
Pin Indent
+0.08
4.52 –0.05
Branded
Face
1
2
45°
3
2.11 MAX
0.51 REF
0.46 REF
A
+0.05
0.43 –0.07
+0.03
0.41 –0.06
NNT
YWW
1.27 NOM
1
14.73 ±0.51
D
Standard Branding Reference View
N
T
Y
W
= Supplier emblem
= Last two digits of device part number
= Temperature code
= Last digit of year of manufacture
= Week of manufacture
A
Dambar removal protrusion (6X)
B
Gate and tie bar burr area
C
Active Area Depth = 0.42 NOM
D
Branding scale and appearance at supplier discretion
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: UA - TI/TJ/TN
Type: 3-pin SIP, matrix leadframe
For Reference Only – Not for Tooling Use
(Reference DWG-9065)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45° (2X)
B
5° (2X)
4.09
+0.08
–0.05
1.68 MAX
1.52 ±0.05
3.00 ±0.05
B
C
Ejector Pin
Flash Protrusion
10° (3X)
3.10 MAX
3.02
+0.08
–0.05
45°
Branded
Face
1.02 MAX
1
2
3
0.51 REF
A
0.10 MAX
0.79 REF
0.05 NOM
0.43
+0.05
–0.07
0.41
+0.03
–0.06
1.27 NOM
NNN
14.99 ±0.25
1
D
Standard Branding Reference View
= Supplier emblem
N = Last three digits of device part number
A
Dambar removal protrusion (6X)
B
Gate and tie bar burr area
C
Active Area Depth, 0.50 mm REF
D
Branding scale and appearance at supplier discretion
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: UA - TI/TJ/TN
Type: 3-pin SIP, conventional leadframe
For Reference Only – Not for Tooling Use
(Reference DWG-9049)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45°
B
4.09
+0.08
–0.05
1.52 ±0.05
C
Mold Ejector
Pin Indent
3.02
+0.08
–0.05
45°
Branded
Face
1
2
3
2.16 MAX
0.79 REF
A
0.43
+0.05
–0.07
0.41
+0.03
–0.06
1.27 NOM
15.75 ±0.51
NNT
1
D
Standard Branding Reference View
= Supplier emblem
N = Last two digits of device part number
T = Temperature code
A
Dambar removal protrusion (6X)
B
Gate burr area
C
Active Area Depth, 0.50 ±0.08
D
Branding scale and appearance at supplier discretion
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: UA - TL/TS
Type: 3-pin SIP, conventional leadframe or matrix
For Reference Only – Not for Tooling Use
(For package outline, reference DWG-9065; for lead forming, reference DWG-9116)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
45°
B
4.09
+0.08
–0.05
D
1.52 ±0.05
10°
3.02
Mold Ejector
Pin Indent
+0.08
–0.05
45°
45°
Branded
Face
1.02 MAX
2.41 ±0.13
1
2
A
3
A
0
0.79 REF
0.43
+0.05
–0.07
0.41
1.27 NOM
+0.10
–0.051
+0.03
–0.06
0.97
0.51 MIN
NNN
1.57
PCB Reference Layout View
F
8°
0°
1
1.27
D
Standard Branding Reference View
Detail A
= Supplier emblem
N = Last three digits of device part number
A
Dambar removal protrusion (8X)
B
Gate and tie burr area
C
Branding scale and appearance at supplier discretion
D
Active Area Depth, 0.50 ±0.08
F
Reference land pattern layout; all pads a minimum of 0.20 mm from all
adjacent pads; adjust as necessary to meet application process requirements
and PCB tolerances
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com
Package Drawing
Designator: UB
Type: 2-pin SIP, molded lead bar
For Reference Only – Not for Tooling Use
(Reference DWG-9070)
Dimensions in millimeters – NOT TO SCALE
Dimensions exclusive of mold flash, gate burrs and dambar protrusions
Exact case and lead dimensions at supplier discretion within limits shown
B
4 X 10°
1.50±0.10
4.00 ±0.05
C
Mold Ejector
Pin Indent
4.00 ±0.05
Branded
Face
A
4 X 2.50 REF
0.25 REF
45°
0.85 ±0.05
0.42 ±0.10
0.30 REF
2.54 REF
4 X 0.85 REF
1
NNN
2
1.00 ±0.10
12.20 ±0.10
1
+0.05
0.25 –0.03
4 X 7.37 REF
D
1.80
REF
Standard Branding Reference View
= Supplier emblem
N = Last three digits of device part number
0.38 REF
0.25 REF
4 X 0.85 REF
0.85 ±0.05
1.80 ±0.05
E
4.00 ±0.05
A
Dambar removal protrusion (8X)
B
Gate and tie bar burr area
C
Active Area Depth, 0.38 mm REF
D
Branding scale and appearance at supplier discretion
E
Thermoplastic Molded Lead Bar for alignment during shipment
1.50 ±0.10
Copyright ©2008-2013, Allegro MicroSystems, LLC drawings are for reference only; not for tooling use. Refer to the individual datasheet for information on a specific product package. Allegro MicroSystems, LLC reserves
the right to make, from time to time, such departures from the detail specifications as may be required to permit improvements in the performance, reliability, or manufacturability of its products. Before placing an order, the
user is cautioned to verify that the information being relied upon is current. The information included herein is believed to be accurate and reliable. However, Allegro MicroSystems, LLC assumes no responsibility for its use;
nor for any infringement of patents or other rights of third parties which may result from its use.
Allegro MicroSystems, LLC
115 Northeast Cutoff
Worcester, Massachusetts 01615-0036 U.S.A.
1.508.853.5000
For the latest version of this document, visit our website:
www.allegromicro.com