Bitte decken Sie die schraffierte Fläche mit einem Bild ab.
Please cover the shaded area with a picture.
(24,4 x 11,0 cm)
Tire removal and installation instruction using a manual tire
changer.
Version 1.5
I B&S TIS
Contents
1 Tire mounting with manual tire changer
2 Tire dismounting with manual tire changer
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
2
1. Fix the rim in the tire changer
Position the sensor opposite to the
mounting head
Don’t position the sensor at other location
because it may be hit by the tire
Mounting head
Mounting head
Sensor
180°
Sensor
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
3
2. Mount the lower bead
Mount the lower bead making sure that the
tire does not slide
If the tire slides the correct sensor position is
lost and the tire can hit the sensor
Mounting head
Sensor
Sensor
Example marking to
indicate the sensor
position before
mounting
Mounting head
Example marking to
indicate the sensor
position before
mounting
Mounting head
Sensor
Mounting head
At the end of the
mounting the marking
and the sensor position
match => No sliding of
the tire occurred
Public
Sensor
At the end of the
mounting the marking
and the sensor position
don’t match => Sliding
of the tire occurred
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
4
3. Position the sensor for the upper bead mounting
Position the sensor opposite to the
mounting head
Don’t position the sensor at any other
location because it may be hit by the tire
Sensor
Mounting head
Sensor
Mounting head
180°
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
5
4. Mount the upper bead
Mount the upper bead making sure that the
tire does not slide
Sensor
Mounting head
Example marking to
indicate the sensor
position before
mounting
If the tire slides the correct sensor position is
lost and the tire may hit the sensor
Sensor
Mounting head
Example marking to
indicate the sensor
position before
mounting
Sensor
Sensor
Mounting head
At the end of the
mounting the marking
and the valve match =>
No sliding of the tire
occurred
Public
Mounting head
At the end of the
mounting the marking
and the valve don’t
match => Sliding of the
tire occurred
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
6
Contents
1 Tire mounting with manual tire changer
2 Tire dismounting with manual tire changer
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
7
1. Break the bead on the front side
Position the bead breaker on the opposite
side of the sensor
Don’t position the bead breaker at the sensor
position as it may be damaged
Sensor
Sensor
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
8
2. Break the bead on the rear side
Position the bead breaker on the opposite
side of the sensor
Don’t position the bead breaker at the sensor
position as it may be damaged
Sensor
Sensor
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
9
3. Fix the wheel in the tire changer
Position the sensor under the mounting
head
Mounting head
Don’t position the sensor at any other
location because it may be hit by the tire
Mounting head
Sensor
Sensor
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
10
4. Insert the mounting lever
Insert the mounting lever without touching
the sensor
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
11
5. Dismount the upper bead
Dismount the upper bead
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
12
6. Position the sensor for the lower bead dismounting
Position the sensor under the mounting
head
Sensor
Mounting head
Don’t position the sensor at any other
location because it may be hit by the tire
Mounting head
Sensor
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
13
7. Insert the mounting lever
Insert the mounting lever only if the sensor
is under the mounting head
Mounting head
If the sensor is not under the mounting head
it can be caught by the tire
Mounting head
Sensor
Sensor
Mounting head
Mounting head
Sensor
Sensor
View from the rear-bottom
of the mounting machine.
As the sensor is at the
right position (under the
mounting head) it is not
touched by the tire.
Public
View from the rear-bottom
of the mounting machine.
As the sensor is not at
the right position (under
the mounting head) it is
caught by the tire.
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
14
8. Dismount the lower bead
Dismount the lower bead
Public
© Continental AG I May 2015 I Version 1.5 rev NAFTA
Part No. V06216TG1D
15