IGS
O.C.E.M. S.p.A.
ICAO Guidance Sign
Compliance:
ICAO Annex 14
NATO STANAG 3316
IGS
Applications
How to order
ICAO signs, model IGS, are designed for use
on airport taxiways and runways to mark taxi
routes and intersections. Colours may be black
on yellow, yellow o n black, or white on red
depending on the application as defined by
ICAO, Annex 14. IGS signs may be used as
guidance markers in compliance with
STANAG Specs too.
To determine the exact number of modules to
fit your message, contact OCEM.
To construct the catalogue number, add to the
basic part number the size code, the number
of faces and the number of modules.
If required, any option can be added.
Floor flanges included; anchor bolts not
included. Order isolation transformer(s),
Features
I G S
ï
Designed in
150/5345-44
ï
Structural integrity assured by ext
aluminium panels
ï
Matt black external finishing
ï
Metric hardware
ï
Long life fluorescent lamps
Number of Faces :
ï
Modular design with uniform leg spacing
1 = Single Face
2 = Double Face
ï
Two lamps per module, each powered
through a dedicated single-lamp electronic
ballast for maximum reliability
Number of Modules : 1 to 4*
compliance
with
FAA
ruded
ï
SUNLIFE 6111 polycarbonate sign faces
with translucent messages
ï
Message on one or both faces
ï
Breakable couplings may be pre -installed
on concrete pad and sign lowered onto
them for easy installation
ï
Enclosed power entry through protective
flexible pipe
ï
ï
ï
ï
eventual transformer housing with baseplate
and gasket, pipe elbow and connector kit
separately. The colours of the sign faces and
the legends must be specified for each sign.
Multiple messages and colours may appear on
a sign face. W hen facing side A, the power
entry is on the right. Orders should always
specify the message orientation.
External power disconnecting switch
breaks all electrical connections to the sign
for safe maintenance
Operates from 1 step (6.6 A) or 3 steps
(4.8 A to 6.6 A) or 5 steps (2.8 A to 6.6
A) series lighting circuit through isolating
transformers. See TAB LE B on this page
for isolating transformer choice
Constant average sign illuminance (widely
exceeding ICAO Specs) at any series
current step from 2.8 A through 6.6 A. See
TABLE A on this page for illuminance data
Power required to CCR per module:
£150 VA at 6.6 A, £200 VA at 4.8 -6.6 A,
£250 VA at 2.8-6.6 A
ï
Power factor not less than 0.90 at any
series current step from 2.8 A through 6.6
A
ï
Operating temperature:-20°C to +55°C
GOLLAND Sp. z o.o.
www.oswietlenielotniskowe.pl
Basic Part
Number :
Size :
3 = Sign, 300 mm Legend Height
4 = Sign, 400 mm Legend Height
Options :
00 = Without Lamps
* Maximum of (4) Modules for sign. If more modules are required, two signs may be co
-located.
TABLE A - ILLUMINANCE (in cd/m2)
LEGEND
HEIGHT of
SIZE
SIGN FACES
400 mm
300 mm
COLOURS
RED
YELLOW
WHITE
800 mm
70
480
560
600 mm
75
540
700
TABLE B - REQUIRED ISOLATING TRANSFORMERS
Sign
TRANSFORMER
Modules
RATING
1
200 W
2
300 W
3
400 W
4
2x300 W(1)
(1) Use consolidating harness P/N 011.3100 to connect in
series the secondary of the two isolation transformers.
NOTE: performances may vary depending on type and manufacturer of isolation
transformers and CCRs.
FT-3.1
May 1999
ul. StyczyÒskiego 83
41-500
Chorzów
tel. +48 32 349 17 00, +48 32 349 17 01, fax +48 32 349 17 02
e-mail: centrala@golland.pl
Outline Drawings
Lamp
Modules
A
Legend
Height
B
1
2
3
4
991 1976 2961 3946
300
400
838 1038
Dimensions in mm
Instruction Manual: UT-MT-238
Shipping Weights and Volumes :
Modules
Sign Size
1
Kg cu.m
2
Kg cu.m
3
Kg cu.m
4
Kg cu.m
46 0.30
51 0.35
80 0.57
88 0.68
117 0.84
128 1.01
145 1.11
160 1.35
(Legend Height)
300
400
Accessories
Part Number
Description
013.0010
013.0008
315.3210
315.1227
315.1065
011.2056
011.2003
011.2060
011.2006
011.2080
011.2040
011.2559
011.2558
011.3100
Set of two ryton rings for receptacle support inside pipe elbow
Galvanized steel pipe elbow with upper threaded end only
Galvanized steel pipe elbow with both threaded ends
Base L-867, Class I, Size B, 24î deep
Baseplate for L-867 base with gasket and cable clamp
Transformer for series circuits FAA L-831 200 W 6.6/6.6 A
Transformer for series circuits FAA L-831 200 W 6.6/6.6 A, suitable for secondary grounding
Transformer for series circuits FAA L-831 300 W 6.6/6.6 A
Transformer for series circuits FAA L-831 300 W 6.6/6.6 A, suitable for secondary grounding
Transformer for series circuits FAA L-831 400 W 6.6/6.6 A
Transformer for series circuits FAA L-831 400 W 6.6/6.6 A, suitable for secondary grounding
54-E6-E6 Connector kit L-823, 10-12 AWG (6 sq.mm), 0.42î to 0.585î O.D.
54-E4-E4 Connector kit L-823, 8 AWG (10 sq.mm), 0.42î to 0.585î O.D.
Consolidating harness
Renewal Parts
Part Number
Description
303.7320
303.7330
760.3615
169.5210
657.0045
150.1964
323.2367
464.0238
470.0218
Breakable coupling for sign with 400 mm lege
nd height (type 2434-4)
Breakable coupling for sign with 300 mm legend height (type 2434
-3)
30W fluorescent lamp, dia 26 mm
G13 lampholder (IP 67) with hardware
Single-lamp electronic ballast
Electronic card E897
Cable lead with plug
ON-OFF switch
Rubber cap for switch
GOLLAND Sp. z o.o.
www.oswietlenielotniskowe.pl
ul. StyczyÒskiego 83 41-500 Chorzów
tel. +48 32 349 17 00, +48 32 349 17 01, fax +48 32 349 17 02
e-mail: centrala@golland.pl