For Pricing and Days to Ship,Please Configure Online. Lock Washers (Nord-Lock®) / Tab Washers / Disc Spring Washers U-Nuts® / Double Locking Nuts Hard Lock Nuts® Part Number 7 7.6 9 10.8 13.5 16.6 19.5 d t 3.4 4.4 2.2 5.4 6.5 8.7 10.7 2.0 13 Unit Price Volume Discount Rate 1~9 pc(s). QU-Nuts® is not RoHS compliant. E (M6 or Less) (M8 or More) S S Configure Online QPrinciple of Lock Washers Counterbore dia. does not need to be increased. A pair of washers with wedge cams on one side and radial ribs on the other side each to compose a self-locking arrangement. Cam angle (@) is set to be larger than the thread lead angle (B). W hen the screw attempts to rotate loose, a force is generated by a cam member to push up and separate from the opposite cam member. The rotation is blocked by the wedge effect and the cams will not be separate by more than one thread pitch. (e) NLDF3 Type Single Item 10~199 pc(s). 200 pcs. or More Part Number b Correct Wrong Type N LDF can be used repeatedly with a lubricant. QAbout Mating Materials O n the surface of mating materials, there will be impression marks made by the radial teeth of the washers. The hardness of the mating surfaces should not exceed the hardness of the Nord-Lock Washers. T emperature limit for NLDF is 500°C. Do not use in an environment when it exceeds the temperature limit. P lease refer to the values listed below as guidelines when securing a screw with a lock washer. There is no self-locking effect when the values are far below recommended values. If the tightened torque exceeds the recommended values, loosening the screws may become impossible or Nord-Lock may be broken. 8mm Standard Nut Tightened Tightened with 50mm Tightening Length Nylon Resin Nut Spring Washer Standard Nut of 8mm 8mm Standard Nut and Nord-Lock tightened at 25% Yielding Point 10 5 100 200 300 Screw Tightening Torque and Recommended Tightening Force when Lock Washer is Used. (Lubricant GTP600) 10 Applicable Screw MxP NLDF Screw Strength Class A2-80, A4-80 GF=0.65 µg=0.14 µw=0.14 Screw Strength Class A2-70, A4-70 GF=0.65 µg=0.14 µw=0.14 Tightening Torque N·m Tightening Force kN Torque N·m Force kN 3 3x0.5 0.9 1.5 1.2 2 4 4x0.7 2 2.6 2.7 3.4 5 5x0.8 3.9 4.1 5.3 5.5 6 6x1.0 6.9 5.9 9.2 7.8 8 8x1.25 17 11 22 14 36_36PACK-NLDF 10 10x1.5 33 17 43 23 12 12x1.75 56 25 75 33 EGF: Coefficient at the Yield Point µg: Coefficient of Friction at Screw Thread µw: Coefficient of Friction in Washer 5 GTS QSerrated Conical Disc Spring Washers d b 15 400 Frequency of Vibration PACK-ZAST QTab Washers-One-Tabbed Tab Washers-Two-Tabbed Q Released SSRBW QDisc Spring Washers UNUTZ UNUTKZ UNUTSZ PACKZAST PACKZATT 3.2 4.3 5.3 6.5 8.5 10.5 12.5 17 21 25 3 4 5 6 8 10 12 16 20 24 12 14 17 18 22 26 30 38 45 52 7 9 10 13 16 20 24 30 38 44 Pitch Unit Price Volume Discount Rate l l1 b 1~9 pkg(s). 10 pkgs. or More 4 5 13 5 0.29 14 7 8 15 9 0.5 20 13 22 14 0.8 27 19 32 24 1.2 36 28 44 35 Part Number Type No. 6 7 9 10 12 15 17 GTS 3 4 5 6 8 10 12 16 20 24 D d H 5.5 7 8.5 10 13 16 18 24 30 36 3.2 4.25 5.25 6.4 8.4 10.6 12.6 16.9 20.9 25.4 0.6 0.7 0.85 1.25 1.55 1.90 2.20 2.80 3.55 4.25 Part Number PACK-ZAST3 GTS10 SSRBW8 P Friction Ring P' Unit Price Volume Discount Rate t * Less than * or More * Quantity 15000 10000 5000 6000 3000 2000 1000 500 250 150 0.45 0.5 0.6 1.0 1.2 1.5 1.8 2.3 2.8 3.5 4 5 6 8 10 12 16 0.7 0.8 1.0 1.25 1.5 1.75 2.0 Tolerance 7 8 10 13 17 19 24 Part Number UNUTZ4 PACK-UNUT12 d H t 4.3 5.3 6.4 8.4 10.5 13.0 0.7 0.85 0.95 1.3 1.6 1.75 0.45 0.55 0.60 0.90 1.10 1.20 Reference Dim. 0 -0.2 0 -0.25 0 -0.35 Type MMaterial SSurface Treatment 1018 Carbon Steel Trivalent Chromate HLN HLNS 304 Stainless Steel H a M D (e) ELight Load 7.5 9.0 10.5 13.5 16.5 19.0 M Qty. /1 pkg. m Tolerance 3.8 4.6 5.1 7.3 8.3 10.5 14.5 H1 (h) B l a: Eccentricity Unit Price Volume Discount Rate 1~49 pc(s). 50~69 70~99 100~500 EM14 and M16 are not flanged. ±0.3 ±0.4 ±0.5 P1 Eccentric Center of Convex Side of the Lower Nut Strong wedge action will take effect here. Upper Nut a a b Configure Online (Fig.-1) P1 P3 Lower Nut P2 (Fig.-2) Tightening Torque N·m (kg·cm) UNUT, UNUTK 2.2 (22) 4.4 (45) 7.4 (75) 18 (180) 36 (370) 62 (630) 155 (1600) 8.1 9.2 11.5 15 19.6 21.9 27.7 UNUTS 1.9 (19) 3.8 (39) 6.5 (66) 16 (160) 31 (320) 55 (560) 135 (1400) Cautions · At least two thread pitches should protrude from the friction ring. 1. When tightening the nut refer to the Tightening Torque Chart. 2. Use chamfered tipped screws of JIS6g (Class 2) in thread precision. 3. Use appropriate lubricant if seizure or scuffing occurs when screwing or unscrewing the nut onto threads. 4. Cannot be screwed in from the friction ring side. 5. Discontinue use if abnormal deformation occurs in the friction ring or the clamp. Part Number Type M 6 8 HLN 10 HLNS 12 (Stainless Steel) 14 16 MxPitch B (e) 6x1.0 8x1.25 10x1.5 12x1.75 14x2.0 16x2.0 10 13 17 19 22 24 11.5 15 19.6 21.9 25.4 27.7 1Lower Nut 2Upper Nut Pair Height H Tolerance H1 Tolerance l Tolerance 0 ±0.3 5 5 8 -0.3 6.5 6.5 10.6 0 0 8 8 13.2 -0.58 -0.58 10 9.3 16 11 11 18.5 0 0 -0.7 -0.7 13 13 22.5 (h) 3 4.1 5.2 7.0 7.5 9.5 Weight per Unit Price Set (g) HLN HLNS 4 8.9 18 26 39 52.8 QTightening Torque Chart (Reference Value) 1Lower Nut 2Upper Nut By Material: Tightening Torque Reference Value Chart (N · m) All Materials M 1018 Carbon Steel or Equivalent 1045 Carbon Steel or Equivalent 4137 Alloy Steel or Equivalent 304 Stainless Steel/316 Stainless Steel or Equivalent Tightening Torque (N·m) 4.8(320N/mm2) 8.8(640N/mm2) 10.9(900N/mm2) 50(210N/mm2) 70(450N/mm2) 6 2.3~6 1.5~4 3.3~9 4~5 8 5.6~15 11.2~30 15.8~42 3.7~10 7.9~21 9~13 10 11~30 22~59 31~84 7~20 16~42 18~24 12 19~52 39~104 55~146 13~34 27~73 27~39 14 31~82 62~165 87~232 20~54 44~116 40~58 16 48~129 97~257 136~362 32~84 68~181 70~100 QStructure and Function of Hard Lock Nuts® EHard Lock Nuts® is a registered trademark of Hard Lock Screw Center of Bolt and Nut PACK-UNUT PACK-UNUTK PACK-UNUTS Unit Price Volume Discount Rate Unit Price Volume Discount Rate Unit Price Volume Discount Rate 1~9 pkg(s). 10 pkgs. or More 1~9 pkg(s). 10 pkgs. or More 1~9 pkg(s). 10 pkgs. or More (e) 3 3.9 4.2 6.1 7.1 9 13 QFeatures of U-Nuts® · Capable of stable anti-loosening effect. Prevents screws from falling off even with declines in axial tension. · Being a solid metal product, the nuts are highly resistant to heat and cold. · Simplified fastening task makes work management easier. · Easy parts management prevents inappropriate installation. · Reusable. QDouble Locking Nuts d SSRBW 4 5 6 8 10 12 Type Configure Online M Material: 304 Stainless Steel H Hardness: 37 to 46HRC J IS B 1251 Class 2 Equivalent Part Number D Type No. Part Number h Reference Dim. H M Material: From 1049 Carbon Steel to S70C H Hardness: 40 to 48HRC S Surface Treatment: Tempered Collar JIS B 1251 ENo.3 to 5, Light Load; No.6 to 24, Heavy Load 2 -223 D d t d D D1 t h m EU-Nuts® is a trademark of Fuji Seimitsu Co. Ltd. S M D1 l1 b d Part Number Type No. - 100 100 100 100 50 12 50 16 50 * 100 pcs./pkg. for M4~8; 50 pcs./pkg. for M10~16. 2 1 H M Material: 304 Stainless Steel E10 pcs. per pkg. 301 Stainless Steel 4 5 PACK-ZATT l 301 Stainless Steel When the friction ring makes a contact with the thread as shown in the figure below, spring action generates a reaction force P. A friction torque (prevailing torque) that prevents the nut from rotating is then generated by the nut due to another reaction force P'. UNUT, UNUTZ4~12 UNUTK, UNUTKZ4~12 h m 301 Stainless Steel Screw Precision Pure Titanium Class 2 Pure Titanium Class 2 Pure Titanium Class 2 PACK-UNUT 6 PACK-UNUTK 8 PACK-UNUTS 10 t b PACK-UNUTS 4 5 6 8 10 12 16 t D Axial Force [kN] Junker Test Result 15 UNUTSZ 1018 Carbon Steel or Equivalent 1018 Carbon Steel or Equivalent 304 Stainless Steel or Equivalent Friction Ring QRecommended Tightening Torque and Tightening Force 8mm Standard Nut and Nord-Lock tightened at 70% Yielding Point PACK-UNUTK UNUTZ UNUTKZ UNUTSZ Unit Price Volume Discount Rate Unit Price Volume Discount Rate Unit Price Volume Discount Rate 1~9 pc(s). 10 pcs. or More 1~9 pc(s). 10 pcs. or More 1~9 pc(s). 10 pcs. or More M Wrong QCautions on Repeated Use M Friction Ring M @ The washers come pre-assembled in pairs (glued). Upon reusing, please confirm the cams are not worn or cracked, and follow the installation instruction on the right. Do not use together with other washers. Screw M8 (A4-80) Tightening Length: 25mm PACK-UNUT UNUTKZ SSurface Treatment Bright Chromate Plating Trivalent Chromate @ >b QProper Installation QAllowable Temperature UNUTZ UNUT, UNUTZ16 UNUTK, UNUTKZ16 UNUTS, UNUTSZ4~16 Friction Ring Material Main Material Pkg. 90°~120° M Material: 316L Stainless Steel Equivalent H Hardness: 51HRC EThis product is to be used in pairs. D 90°~120° t Part Number Applicable Screw Type No. 3 M3 4 M4 5 M5 NLDF 6 M6 8 M8 10 M10 12 M12 (e) d D NLDF Industry Co., Ltd. Cautions Screws or shafts should be made to JIS6g (Class 2) in thread precision. Nuts may not fit well in different thread precision. Although O.D. of the upper nut and the lower nut may become eccentric or clearance may occur during assembling caused by its structure, it does not affect the operation. Part Number HLN8 Configure Online Configure Online * Fig.-1: When upper nut is tightened, stress is automatically applied in P1 arrow direction. Horizontal stress continues to increase with tightening until upper nut closely contacts lower nut as shown in Fig.-2. The nuts are fully locked by the wedge effect. * Fig.-2: After nuts are tightened, internal stress remains distributed as composite stress of P1+P2+P3 to resist external impact. 2 -224