ZG - Nichicon

advertisement
ALUMINUM ELECTROLYTIC CAPACITORS
ZG
3.95mmL MAX. Chip Type,
Wide Temperature Range
series
Chip type with 3.95mmLMAX height. Operating over wide
temperature range of – 40 to +105°C.
Designed for surface mounting on high density PC board.
Applicable to automatic mounting machine fed with carrier tape.
Compliant to the RoHS directive (2011/65/EU).
ZT
Smaller
ZG
Specifications
Item
Performance Characteristics
Category Temperature Range
–40 to +105°C
Rated Voltage Range
6.3 to 50V
Rated Capacitance Range
0.1 to 100µF
Capacitance Tolerance
± 20% at 120Hz, 20°C
Leakage Current
After 2 minutes' application of rated voltage, leakage current is not more than 0.01 CV or 3 (µA) , whichever is greater.
6.3
10
16
25
35
50
0.38
0.32
0.20
0.16
0.14
0.14
Rated voltage (V)
6.3
10
16
25
35
50
Impedance ratio Z–25°C / Z+20°C
ZT / Z20 (MAX.) Z–40°C / Z+20°C
6
5
3
3
3
3
10
10
6
6
4
4
Rated voltage (V)
Tangent of loss angle (tan δ)
tan δ (MAX.)
Stability at Low
Temperature
Capacitance change
tan δ
Leakage current
120Hz
Within ±30% of the initial capacitance value
300% or less than the initial specified value
Less than or equal to the initial specified value
Endurance
The specifications listed at right shall be met when the
capacitors are restored to 20°C after the rated voltage is
applied for 1000 hours at 105°C.
Shelf Life
After storing the capacitors under no load at 105°C for 1000 hours and then performing voltage treatment based on JIS C 5101-4
clause 4.1 at 20°C, they shall meet the specified values for the endurance characteristics listed above.
Resistance to
soldering heat
The capacitors are kept on a hot plate for 30 seconds, which is
maintained at 250°C. The capacitors shall meet the characteristic
requirements listed at right when they are removed from the plate and
restored to 20°C.
Marking
Black print on the case top.
Chip Type
V
Capacitance
3.90
+0.05
–0.2
3.90
+0.05
–0.2
6.3
10
16
25
35
50
j
A
C
E
V
H
Code
Within ±10% of the initial capacitance value
Less than or equal to the initial specified value
Less than or equal to the initial specified value
1
C±0.2
E
E
0.5 to 0.8
Negative
0.5 to 0.8
Negative
2
3
4
5
6
7
8
9 10 11 12 13 14
U1 Z2 G3 14 C5 16 07 08 M9 C10 L11 112 G13 B14
U ZG 1 C 1 0 0 MC L 1 GB
Positive
A±0.3
A±0.3
A±0.3
A±0.3
Capacitance
C±0.2
B±0.2
B±0.2
Series
φD±0.5
φD±0.5
Series
Lot No.
X2 A2
10C
10C
ZGZG
Lot No.(C : 16V)
Voltage
Plastic platform
0.3 MAX.
Plastic platform
0.3 MAX.
0.5 MAX.
0.5 MAX.
Voltage (C : 16V)
Voltage
Capacitance change
tan δ
Leakage current
Type numbering system (Example : 16V 10µF)
Positive
120Hz 20°C
φD
A
B
C
E
4
1.8
4.3
4.3
1.0
5
2.1
5.3
5.3
1.3
(mm)
6.3
2.4
6.6
6.6
2.2
Taping code
Configuration
Taping code
Configuration
Capacitance tolerance
(±20%)
Capacitance
tolerance(10µF)
(±20%)
Rated capacitance
Rated
capacitance
(10µF)
Rated
voltage (16V)
RatedSeries
voltage
(16V)
name
SeriesType
name
Type
Dimensions
6.3
0J
V
Cap. (µF)
0.1
0.22
0.33
0.47
1
2.2
3.3
4.7
10
22
33
47
100
Code
0R1
R22
R33
R47
010
2R2
3R3
4R7
100
220
330
470
101
4
5
5
6.3
10
1A
19
26
32
52
5
5
6.3
16
1C
24
30
40
4
5
6.3
6.3
25
1E
16
26
35
44
4
5
6.3
6.3
35
1V
11
20
33
42
4
5
6.3
13
22
36
4
4
4
4
4
4
4
5
6.3
50
1H
Case size
φ D (mm)
0.9
2.2
2.8
3.3
5.4
9.6
12.
16.
26.
Rated
ripple
Rated ripple current (mArms) at 105°C 120Hz
Frequency coefficient of rated ripple current
Frequency
Coefficient
50 Hz
0.70
120 Hz
1.00
300 Hz
1.17
1 kHz
1.36
10 kHz or more
1.50 Taping specifications are given in page 23.
Recommended land size soldering by reflow are
given in page 18,19.
Please refer to page 3 for the minimum order quantity.
CAT.8100D
Download