14. Rese — — — — 15. Torqu If the posit nece be ra 16. Settin Nm

advertisement
14. Resetting limit-switching:
— Operate valve away from end-position to account for over-run or to the desired switch tripping
point.
— Push thrust bolt I inwards and turn (fig. 19). The bolt remains in this position.
— For CLOSED position turn spindle marked
(Z), (for OPEN position spindle marked,
O) slowly as indicated by arrow (fig. 19). Distinct "clicks" can be felt and heard. Continue
turning the spindle until the cam operates the switch. At this stage, the spindle should not
"click" any more and should not be turned any further.
If inadvertently you override the tripping point, continue turning the spindle slowly in the
same direction till the switch cam goes back to its original position. Repeat setting
instructions as above described.
— Turn thrust bolt I till it snaps back into its original position by spring action.
15. Torque switching (fig. 20)
If the actuator is switched off by torque switch over its travel before reaching an endposition, please check whether the valve stem is damaged or dirt adhering to it. If
necessary, and with the valve maker’s consent, the setting of the tripping torque may
be raised slightly.
16. Setting : Figures on the torque switch operating cam indicate the valves in Nm (1 mkp = 10
Nm. 1 lbsft. = 1.36 Nm).
Loosen screw and turn the cam till the desired torque coincides with the arrow mark, then
fasten lock-screw.
17. Immediately after start-up : Ensure sealing faces at cover and housing are clean. Check
whether O-ring is correctly in position and apply a thin film of non-acid grease. Replace the
cover and fasten with 4 screws (fig. 21).
18. Fasten control cover screws and tighten glands at conduit entries.
12
9
SA 3 - SAR 100
SAR 3 - SAR 100
Spare Parts
When placing orders for spare parts it is essential to mention order number, work’s number and type of the actuator
(refer to name plate). Parts with number in a circle, e.g. 8 , will be supplied complete only.
Part
No.
1
2
3
4
5
6
7
8
14
15
16
17
18
19
21
23
24
Designation
Part
No.
Gear box housing
Switch compartment cover
External bearing retainer
Internal bearing retainer
Declutch lever
Clutch roller pin, short
Clutch roller pin, long
Clutch fork assembly
Declutch tripping arm
Retaining plate
041
043
045
047
048
052
058
Blinker switch (SPST)
Spring washer
Lock washer
Lock washer
Fillister head screw
Support washer
Star washer
2.1
2.011
2.012
2.013
Motor pinion
Spur gear
Motor mounting flange
Shield
Worm gear
Motor
O-ring
O-ring
Hexagon head bolt
Lock washer
Flat washer
Hexagon head bolt
Lock washer
Fillister head screw
Lock washer
3.1
3.5
3.6
3.01
3.02
3.03
Indicator assembly
Indicator glass
Glass retaining ring
O-ring
Fillister head screw
Lock washer
4.4
4.7
4.8
4.11
4.12
4.13
Stem protection tube
Stub shaft (type D)
Mounting flange (type D & F)
Mounting flange (type A)
Stem nut (type A)
Bearing locknut
4.21
4.22
4.23
4.24
4.75
4.05
4.06
4.07
4.08
4.09
4.010
Mounting flange (types B & C)
Dog drive sleeve (type C)
Thrust ring
Keyway drive sleeve (type B)
Drive socket (type E)
Stud bolt
Flat washer
Hexagon nut
Cap
Hexagon head bolt
Lock washer
4.011
4.012
Parallel key
Lock washer
Return spring
Spacer
Bushing
Retaining ring (SA 6 only)
Worm shaft assembly
Bearing flange
25
26
27
29
30
36
37
Hollow drive shaft
Compressing spring
Clutch Ring
Helical gear (SA 6 only)
Handwheel
Handwheel retainer
Pinion gear (Shaft assembly)
Compression spring
01
02
03
04
05
06
O-ring (Clutch roller pin)
O-ring (Declutch lever)
O-ring (drive assly. flanges)
O-ring (bearing retainer)
O-ring (Handwheel)
O-ring (Bearing flange)
07
010
013
014
O-ring (Switch comp. cover)
Quad ring
8
017
021
022
023
024
025
027
028
030
031
032
033
034
035
039
Oil seal
Oil seal
Ball bearing
Circlip
Circlip
Circlip
Circlip
Circlip
Snap ring
Lid
Hexagon head bolt
Hexagon head bolt
Thin shank hex head bolt
Counter sunk oval head screw
Hexagon head bolt
Fillister head screw
Parallel key
2.2
2.3
2.4
2.6
2.7
2.8
2.02
2.05
2.06
2.09
2.010
Designation
Part
No.
Designation
44.01
44.02
44.03
44.04
Set screw
Grease nipple
Thrust bearing
Thrust bearing race
5.1
5.2
5.01
5.02
5.03
5.04
5.05
5.06
5.07
5.08
5.09
5.010
Terminal box cover
Terminal mounting plate
Pin carrier (control)
Socket carrier (control)
Plug pin (control)
Plug socket (control)
Fillister head screw
Lock washer
Conduit gland
Thrust washer
Seal ring
O-ring
6.1
6.2
6.7
6.8
Pin carrier (motor)
Socket carrier (motor)
Plug pin (motor)
Plug socket (motor)
7.1
7.2
7.05
7.06
Limit switch (SPDT)
Torque switch (SPDT)
Fillister head screw
Lock washer
9.1
9.1
9.01
9.02
Potentiometer *
Potentiometer with Drive Gears*
Fillister head screw
Lock washer
31
Limit switch drive assembly
44
Limit switch counter gear
Torque switch drive assembly
Reduction gearing assembly
45
46
Optional Accessories:
Resistive Position Transmitter :
RWG 2002
RWG 1001
RWG 2002G
RWG 2002DG
Inductive Position Transmitter:
IWG 1002
IWG 1003
Power Supply Unit PS01
Electronic Positioner CU01
*state resistance when ordering
13
Download