SPECIFICATION FOR SAND AND GRAVEL
USED FOR POTABLE WATER SUPPLY
SPECIFICATION SAJH CH/SG/001
(Rev.0.0 / 05.2002)
QUALITY ASSURANCE DEPARTMENT
SAJ HOLDING SDN. BHD.
NO CHANGES ALLOWED WITHOUT THE PERMISSION OF QUALITY ASSURANCE DEPARTMENT
OF SAJ HOLDINGS SDN BHD
QUALITY ASSURANCE DEPARTMENT
SAJ HOLDINGS SDN. BHD.
SAJH Specification For Sand And Gravel
Used For Potable Water Supply
CONTENT
PAGE
Content
2
1.0
GENERAL
3
2.0
FEATURES REQUIRED
3
3.0
TEST AND INSPECTION
4
4.0
PACKAGING AND STORAGE
4
5.0
MANDATORY MARKING
4
6.0
PRE-DELIVERY INSPECTION AND EVALUATION
5
7.0
CERTIFICATION
5
SAJH CH/SG/001 (Rev. 0.0 / 05.2002)
NO CHANGES ALLOWED WITHOUT THE PERMISSION OF QUALITY ASSURANCE DEPARTMENT
OF SAJ HOLDINGS SDN BHD
2
QUALITY ASSURANCE DEPARTMENT
SAJ HOLDINGS SDN. BHD.
Specification for Sand And Gravel Used
For Potable Water Supply
1.0
GENERAL
1.1)
This specification is applicable to Sand And Gravel Used For Potable Water Supply
accordingly to Spesifikasi JKR 20200-0134-02, JKR Standard Specification For Sand And
Gravel Used For Potable Water Supply.
1.2)
Features required for this specification are as follows or otherwise the above specification will
be applied.
2.0
FEATURES REQUIRED
2.1)
Sand And Gravel Used for Potable Water Supply shall comply with requirement as specified
in Table 1 – Product Specification.
Table 1 – Product Specification
Parameter
A. Specific Requirement
Uniformity coefficient
Requirement
Test Method
1.6 max
Acid soluble material (as loss), %(w/w)
Nominal Effective Size, mm
Fine Sand
Gravel
2 max
0.5 – 1.5
3-9
ASTM C136
EN 12902
EN 12902
ASTM C136
EN 12902
B. Chemical Composition
SiO2, %w/w
A12O3, %w/w
Fe2O3, %w/w
CaO, %w/w
K2O, %w/w
Na2O, %w/w
96 min
1 max
2 max
0.5 max
1 max
1 max
EN 12902
EN 12902
EN 12902
EN 12902
EN 12902
EN 12902
Moisture, %(w/w)
15 max
AWWA B100-96
EN 12902: 1999
D. Physical Requirement
Apparently density, g/cm³
1.4 min
Friability, % w/w
15 max
ASTM C127, C128
EN 12902
ASTM D409
C. Impurities
SAJH CH/SG/001 (Rev. 0.0 / 05.2002)
NO CHANGES ALLOWED WITHOUT THE PERMISSION OF QUALITY ASSURANCE DEPARTMENT
OF SAJ HOLDINGS SDN BHD
3
QUALITY ASSURANCE DEPARTMENT
2.2)
SAJ HOLDINGS SDN. BHD.
Physical Properties Sand And Gravel are as follows:
No.
1.
Appearance
Physical Properties
i.
ii.
2.
Density
i.
ii.
iii.
3.0
Descriptions
Grey/White/multicoloured
Crystalline structure, smooth to
rough texture
Absolute density approximately
2.1g/cm³
Bulk
density
loosein
range
1.40g/cm³ to 1.70g/cm³
Bulk density
ity packed in range
1.50g.cm³ to 1.90g/cm³
2.3)
Sand And Gravel supplied shall not contain any impurities and additives.
2.4)
Sand must be “River Worn Sand”.
TEST AND INSPECTION
3.1
All Sand And Gravel shall comply with test in accordance with the requirement of
specification.
4.0
5.0
PACKING AND STORAGE
4.1
Sand And Gravel shall be delivered in bag form.
4.2
For storage purposes, in Sand And Gravel shall be store in clean and dry place.
MANDATORY MARKING
Each container of Sand And Gravel shall have mark legibly on it including: 5.1
“Sand And Gravel”, trade name and grade/type;
5.2
Net weight;
5.3
Name, address and telephone number or supplier and/or manufacturer;
5.4
Lot number;
5.5
Date of manufacturing / packaging and shall bear such other marking as required by
applicable laws;
SAJH CH/SG/001 (Rev. 0.0 / 05.2002)
NO CHANGES ALLOWED WITHOUT THE PERMISSION OF QUALITY ASSURANCE DEPARTMENT
OF SAJ HOLDINGS SDN BHD
4
QUALITY ASSURANCE DEPARTMENT
6.0
SAJ HOLDINGS SDN. BHD.
PRE-DELIVERY INSPECTION AND EVALUATION
6.1
It is the responsibility of the tenderer to inform SAJH for inspection purposes during
manufacturing and before delivery.
6.2
SAJH reserve the right to inspect and witness the testing of the product offered without any
prior notice.
6.3
At any time, when requested, the supplier is to provide SAJH a sample of the product offered
for evaluation purposes. All cost shall be borne by the supplier.
6.4
If at any time, the supplier fails to deliver the required sample, the product is deemed fail to
meet the specification.
7.0
CERTIFICATION
7.1
Manufacturer and/or supplier of the product are required to provide the copy of the certificate
and testing report from SIRIM, IKRAM and/or other certification bodies.
7.2
Tests report required should be those tests conducted within a year period.
7.3
SAJH has the right to refuse offer or reject supply if those documents required are not
enclosed.
SAJH CH/SG/001 (Rev. 0.0 / 05.2002)
NO CHANGES ALLOWED WITHOUT THE PERMISSION OF QUALITY ASSURANCE DEPARTMENT
OF SAJ HOLDINGS SDN BHD
5