Bulletin B1806
• RIBMNLB-6NO
R1 OUT
N/O
R2 OUT
N/O
R3 OUT
N/O
R4 OUT
N/O
R5 OUT
N/O
R6 OUT
N/O
R7
POLE 1
R1
R2
R3
R4
R5
R6
Master
Relay
R7
CLOSED
1 2
R1 R1 COM
OPEN
CLOSED
3 4
R2 R2 COM
R3 R3 COM
Alarm
Input 2
Alarm
Input 3
OPEN
• RIBMNLB-2NO
3A Total Sourced
from 24 Vac/dc Input or Dry
Contact (Jumper Selectable)
Isolated Dry Contact Outputs,
Each Rated 1.5A @ 24 Vac/dc
Alarm
Input
Indicators
• RIBMNLB-4NO
R7
POLE 2
Legend for
Jumper Selection
Master Alarm
Indicator
24V Power
CLOSED
5 6
R4 R4 COM
R5 R5 COM
Alarm
Input 4
Alarm
Input 5
OPEN
R6 R6 COM
Dry =
24V =
COM 24V
4A Max
Alarm
Input 1
Alarm
Input 6
Alarm Input
Bypass Switches
OF ELECTRIC SHOCK - MORE THAN ONE DISCONNECT MAY BE
REQUIRED TO DEENERGIZE THE DEVICE BEFORE SERVICING.
CAUTION: RISK
DE CHOQUE ÉLECTRIQUE - PLUS D´UN INTERRUPTEUR GÉNÉRAL PEUVENT
ÊTRE NÉCESSAIRE POUR METTRE L’ÉQUIPEMENT HORS TENSION AVANT L’ENTRETIEN.
MISE EN GARDE: RISQUE
Bulletin B1806
• RIBMNLB-6NO
R1 OUT
N/O
R2 OUT
N/O
R3 OUT
N/O
R4 OUT
N/O
R5 OUT
N/O
R6 OUT
N/O
R7
POLE 1
R1
R2
R3
R4
R5
R6
Master
Relay
R7
CLOSED
1 2
R1 R1 COM
OPEN
CLOSED
3 4
R2 R2 COM
R3 R3 COM
Alarm
Input 2
Alarm
Input 3
OPEN
• RIBMNLB-2NO
3A Total Sourced
from 24 Vac/dc Input or Dry
Contact (Jumper Selectable)
Isolated Dry Contact Outputs,
Each Rated 1.5A @ 24 Vac/dc
Alarm
Input
Indicators
• RIBMNLB-4NO
R7
POLE 2
R5 R5 COM
Alarm
Input 4
Alarm
Input 5
OPEN
Master Alarm
Indicator
24V Power
CLOSED
5 6
R4 R4 COM
Legend for
Jumper Selection
R6 R6 COM
Dry =
24V =
COM 24V
4A Max
Alarm
Input 1
Alarm
Input 6
Alarm Input
Bypass Switches
OF ELECTRIC SHOCK - MORE THAN ONE DISCONNECT MAY BE
REQUIRED TO DEENERGIZE THE DEVICE BEFORE SERVICING.
CAUTION: RISK
DE CHOQUE ÉLECTRIQUE - PLUS D´UN INTERRUPTEUR GÉNÉRAL PEUVENT
ÊTRE NÉCESSAIRE POUR METTRE L’ÉQUIPEMENT HORS TENSION AVANT L’ENTRETIEN.
MISE EN GARDE: RISQUE
INSTALLATION INSTRUCTIONS
Open breaker
Inputs:
• Alarm Inputs: Connect 2, 4 or 6 Alarms to Input terminal pairs.
• Power Input: Connect to terminals marked 24Vac/dc & COM.
• If tying Inputs to Earth Ground, use the COM terminals
Outputs:
• Dry Contact Outputs: Connect 2, 4 or 6 dry contact outputs from terminals to DDC controller.
• General Purpose: Either 24V or Dry Contact selectable by jumper positions (Master Relay Poles 1 and 2)
Bypass DIP switches:
• Closing any combination of DIP switches will allow corresponding Alarm Inputs to be ignored.
Close Breaker. Green Power LED will be on.
If no alarm conditions exist, the dry contact inputs will be closed, the corresponding Red LEDs will be off and the
Master Relay will be on.
If an alarm condition exists, the corresponding dry contact input will be open, the corresponding LED will be ON, the
Master Relay will be off and the Red Master Alarm LED will be on (unless that Alarm Input was Bypassed).
FOR SUPPLY CONNECTIONS USE #14AWG WIRES OR LARGER RATED FOR AT LEAST 75ºC (167ºF). USE COPPER CONDUCTORS ONLY.
www.functionaldevices.com
393225B
INSTALLATION INSTRUCTIONS
Open breaker
Inputs:
• Alarm Inputs: Connect 2, 4 or 6 Alarms to Input terminal pairs.
• Power Input: Connect to terminals marked 24Vac/dc & COM.
• If tying Inputs to Earth Ground, use the COM terminals
Outputs:
• Dry Contact Outputs: Connect 2, 4 or 6 dry contact outputs from terminals to DDC controller.
• General Purpose: Either 24V or Dry Contact selectable by jumper positions (Master Relay Poles 1 and 2)
Bypass DIP switches:
• Closing any combination of DIP switches will allow corresponding Alarm Inputs to be ignored.
Close Breaker. Green Power LED will be on.
If no alarm conditions exist, the dry contact inputs will be closed, the corresponding Red LEDs will be off and the
Master Relay will be on.
If an alarm condition exists, the corresponding dry contact input will be open, the corresponding LED will be ON, the
Master Relay will be off and the Red Master Alarm LED will be on (unless that Alarm Input was Bypassed).
FOR SUPPLY CONNECTIONS USE #14AWG WIRES OR LARGER RATED FOR AT LEAST 75ºC (167ºF). USE COPPER CONDUCTORS ONLY.
www.functionaldevices.com
393225B