®
HYPONIC Drive
HYPONIC Drive
®
CW19
No. N2201E-5.1
No. N2201E-5
CONTENTS
. Feature ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥2
. Product range‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥8
. Standard specification ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥14
. Nomenclature ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥15
. Information on Electronic catalog ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥16
. Hollow shaft Selection tables and dimensions (15W–5.5kW) ‥‥‥17
3-phase motor ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥18
Single-phase motor (Induction, Reversible) ‥‥‥‥‥‥‥58
3-phase motor for inverter ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥80
. Solid shaft Selection tables and dimensions (15W–90W) ‥‥‥95
3-phase motor ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥96
Single-phase motor (Induction, Reversible) ‥‥‥‥‥‥‥102
. Option‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥113
Solid shaft Flange Mount type (1) Dimension sheet ‥‥‥114
Solid shaft Flange Mount type (2) Dimension sheet ‥‥‥116
Solid shaft Foot Mount type Dimension sheet ‥‥‥‥‥‥118
IEC Flange type Dimension sheet‥‥‥‥‥‥‥‥‥‥‥‥‥‥120
. Water proof type (IP65) ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥123
. Increased safety type (eG3) ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥133
SAFETY PRECAUTIONS
● Strictly observe the safety rules for the installation place and the equipment to use. (Industrial Safety and Health Law,
Technical Standard for Electric Facilities, Extension Rules, Plant Explosion Guidelines, Building Standards Law, etc.)
● Carefully read the maintenance manual before use. If the maintenance manual is not on hand, make a request for one to
the distributor from which you purchased the product or to our sales department. The maintenance manual should be
sent to the actual user.
● Select an appropriate product that matches the operating environment and usage.
● Install protective equipment on the machine side when the machine is used for transportation of passengers or for
elevators, escalators, and dumbwaiters.
● Use an explosion-proof type motor in an explosive environment.
Select an explosion-proof type motor whose specifications is best suited to the danger zone.
● When a 400V-class inverter is used for driving the motor, mount a control filter or reactor on the inverter side or use
a
sufficiently insulated motor.
● When the machine is used for food processing equipment and others that are susceptible to oil, install an oil pan or other
damage preventive devices in case of oil leakage or termination of service life.
Precautions for applications of special motors
● Explosion-proof motors ... When driving an explosion-proof motor, an explosion-proof verification test is necessary for a
motor and an inverter in combination. The same applies to cases where existing explosion-proof motors are driven.
Inverters are of a non explosion-proof type. Install them in a safe place.
● Pole change motors ... The rated current is different from that of general-purpose motors. Confirm the max. current of
the motor before selecting an inverter. Make sure to stop the motor when changing the number of poles, otherwise the
regenerative overvoltage protective circuit or overcurrent protective circuit will be activated, allowing the motor to run
free.
● Motors with brake ... Use an independent power supply for the brake. Be sure to connect the brake power supply to the
primary side of the inverter, and shut off the inverter output when the brake is activated (when the motor is stopped).
Some types of brakes may produce rattling sound during slow-speed running.
● Single-phase motor ... A single-phase motor is not suitable for inverter driving. In the capacitor starting method, the
harmonic current flowing through the capacitor may break the capacitor. In motors of a split-phase-start type and
arepulsion-start type, the centrifugal switch inside will not be activated, possibly burning the starter coil.
When driving a 400V-class general-purpose motor by an inverter
● Contact us in cases where a standard motor is driven by an inverter. The withstand voltage of the motor may have to be
taken into consideration when a high carrier frequency type (IGBT, for example) inverter that has high input voltage
(400V or more) is used or when the wiring distance is long.
Hollow Shaft
Solid Shaft
Option
Increased safety Water proof type
IP65
type eG3
Technical Data
. Technical data ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥137
Selection Procedure ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥138
Construction ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥144
Moment of inertia ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥145
GD2 ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥146
Moment of inertia and GD2 of gearmotors ‥‥‥‥‥‥‥‥147
Rotating direction & Reduction ratio ‥‥‥‥‥‥‥‥‥‥‥148
Actual reduction ratio ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥151
Allowable axial load on output shaft ‥‥‥‥‥‥‥‥‥‥‥152
Lubrication ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥152
Detail dimensions ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥153
Hollow shaft type handling precautions‥‥‥‥‥‥‥‥‥‥154
Torque arm (Option) ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥157
Torque arm designs ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥158
Detail dimensions of output shaft safety cover (separate shipment)‥160
Detail dimensions of output shaft ‥‥‥‥‥‥‥‥‥‥‥‥161
Name plate‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥161
Motor characteristics ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥162
Dimensions of a terminal box ‥‥‥‥‥‥‥‥‥‥‥‥‥‥165
Mounting direction of a terminal box ‥‥‥‥‥‥‥‥‥‥‥166
Specifications and construction of built-in brake ‥‥‥‥‥‥167
Wiring diagram ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥171
Construction of terminal plate for brake motors (optional) ‥‥182
Connection of terminal plate for brake motors (optional) ‥‥182
Protection of motor ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥184
Cooling ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥184
International Standards and corresponding Sumitomo standards for a motor‥185
EC directives and CE marking ‥‥‥‥‥‥‥‥‥‥‥‥‥188
Precautions for Inverter Driving ‥‥‥‥‥‥‥‥‥‥‥‥‥190
Constant Torque Operation of General-Purpose Motors ‥‥191
Painting specifications ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥192
Rust Proof Standards ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥194
Warranty ‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥‥195
ISO 14001 CERTIFICATION
Okayama works has achieved
ISO 14001 for environmental
control. We are constantly
striving to further enhance the
quality of our environmental
management.
1
New More compact gearhead for 0.1kW~2.2kW
Hollow shaft type has been changed fully as the New model
Ratio
1/5
1/60
Exist model
1/240
Motor capacity
0.1kW
More
More compact
compact
More
More light
light weght
weght
0.75kW
1.5kW
2.2kW
ex) Hollow shaft, 3 phase induction motor type
New model
✽ Details are shown on page 3.
New Single Housing Design !
The all New Hyponic provide all three mounting configuration
with a single housing design
RNYM Series
Hollow shaft type
RNFM Series
Flange mount type (1)
RNFM Series
Flange mount type (2)
RNHM Series
Foot mount type
New Tripled the available combinations !
(combinations of capacity and reduction ratio)
with addition of intermediate capacity motor (0.25,0.55,and 1.1kW)
and reduction ratio (1/5,1/7,1/300,1/480,1/560,1/750,1/900,1/1200 and
1/1440) ,a wider range is made available to meet your requirements.
2
angle New HYPONIC allows
New Right
compact designs !
Example 1
Because the mounting bolts are on square pitch
1.Mounting position can be change without protrusion from
existing envelope space.
2.Mounting position can be changed without changing
interface dimensions.
Horizontal mounting
Vertical mounting
49
40
49
40
49
40
49
40
RNYM05-1220-30
Obtained Japan and US patents
RNYM05-1220-30
Patent Number 2628983 5,203,231
Example 2
Example 0.4kW Ratio 1/30
New Series
A=49mm
small
RNYM05-1220-30
Mass 9.5kg
Old Series
A=60mm
A
A
The output shaft is located as close to
the corner as possible toshorten the
distance (Adimensions) between the
center of the shaft and the edge of the
casing.
This all ous the Hyponic to be install
within a very tight space.
A
A
large
RNYM05-33-30
Mass 12kg
3
1.Small sizes of Hyponic Drive ®
■ Water-proof type
IP65 water-proof type Hyponic Drive can be
used in various areas, including food
processing machines.
■ Versatile Installation
New style casing of Hyponic Neo allows
installations from both sides.
2.Advantages of Hyponic Drive ®
Are you sure that your parallel-shaft gear motors
are best for your application?
Hyponic Neo right-angle gearmotors make motors
installations more compact and less costly?
Twin shaft design !
Space-saving design !
Direct drive !
Short
Long
Substantial reduction in the number of mounting parts,
man hours for mounting, and frequency of maintenance.
Safety cover
Chain &
sprocket
Mounting base &
alignment
Shallow
Deep
Right-angle
Inline
4
Torque arm
(option)
3.Features of Hyponic Drive ®
What if you could have right-angle gear
motors with better efficiency and longer
service life than general worm gears ?
HYPONIC DRIVE ® equipped with hypoid
gears. delivers high performance and high
efficiency in a compact package.
■ High efficiency
100
Sumitomo Hyponic Drive
Efficiency (%)
80
General-purpose worm gear
60
40
Input: 1500rpm
Input capacity: 0.1-5.5kw
20
0
Sumitomo Hyponic Drive provides higher
reduction ratio than bevel gears, allowing higher
efficiency in all ranges of reduction ratios.
10
20
30
40
50
60 Reduction ratio
■ Low noise
With larger contact intervals than bevel gears,
Hyponic Drive has a greater transmission capacity,
which results in extremely silent and vibrationless
operation.
Bevel
■ Robust and long-life
Hyponic gears are made of molybdenum steel and
case harden to provide reliable robust operation.
Hypoid
■ Lightweight and compact
Integration of the motor shaft and hypoid pinion
and an aluminamu alloy casing (for frame size
#1531 or #56 and smaller) minimise weight in a
strong compact package.
Worm
■ Maintenance-free
Comparison of 0.4kw, 1/60 models
General-purpose worm gear motor
The long-life grease allows operation without
changing the grease for a long time and allows
installation at any desired angle or incline.
■ World standard
Hyponic Drive
Brakemotors, special voltages, international
standards for outdoor use and other specifications
are also available.
5
4.Features of Hyponic Drive ®
Hollow Shaft (RNYM Series)
The excellent features of the existing models with hollow shafts reduce
Cost by:
❑Fewer mounting parts;
❑Fewer man-hours for mounting; and
❑Eliminating maintenance.
y
fet
Sa ver
Co
ling
up
o
C
ain
Ch
ng
nti
u
Mo se
Ba
t
en
m
gn
Ali
e
anc
n
e
int
Ma
Safety cover
Chain
Worm gear motor
Mounting Base
Innovative Design
To take full advantage of the features of Hypoid
gear set.
The patents include products of hollow shaft,
using gear motors with Hypoid gear set.
Hypoid gear set
Obtained Japan and US patents
Using Hyponic Neo Hollow Shaft Series
❑Space-saving design
❑Excellent design
❑Greater variety of mounting methods
Shaft mount
Two more mounting mothods
(The mounting direction opposite to
the direction below is possible.)
(Flange mount and foot mount (option) shown below are possible.)
●The shaft serves also as a bearing for the driven shaft, so a bearing on one side can be
eliminated.
●This model can be used as a bearing unit with a driving section.
Machine side
Bearing unit
Bearing unit
Hollow shaft type
HYPONIC DRIVE
Example of flange mounting
6
Hollow shaft type
HYPONIC DRIVE
Example of foot mount (option)
(A plate should be furnished by the customer.)
5.Right angle HYPONIC Drive® allows compact designs
Conveyor lines in breweries
Driving trucks
Direct installation using hollow shaft type (with torque arm).
No requirement for sprockets, chains and other coupling equipment.
Crushers
Dehydrator
Easy installation by using through bolts directly into the casing.
Auto-guided vehicle
Wood shaving machine
Direct installation with solid shaft flanges.
7
frame size (q bore diameter)
Hollow shaft type
Note 1
Reduction ratio
Output speed (r/min)
Water proof
type
Motor spec.
Indoor
type
Power supply
1/5
1/7
1/10
1/12
1/15
1/20
1/25
1/30
1/40
1/50
1/60
50Hz
290
207
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
60Hz
350
250
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
15W
03 (q15)
25W
03 (q15)
40W
07 (q15)
60W
07 (q15)
90W
✽ 17 (q15)
110 (q15)
1120 (q20)
0.1kW
0.2kW
Water proof type IP65 (Without brake)
Increased safety eG3
(Without brake, 0.25, 0.55, and 1,1kW are excluded from eG3.)
Outdoor type
3-Phase
1220 (q25)
110 (q20)
Note 5
Water proof
type
Water proof type
IP65 (Without brake)
Outdoor type
Outdoor
type
Indoor type
Single-Phase
0.55kW
1220 (q25)
1320 (q30)
1220 (q25)
1320 (q30)
1210 (q25)
1220 (q25)
1320 (q30)
1320 (q30)
1420 (q35)
1310 (q30)
1320 (q30)
1420 (q35)
1310 (q30)
1320 (q30)
1420 (q35)
0.75kW
1.1kW
1420 (q35)
1520 (q45)
1410 (q35)
1420 (q35)
1520 (q45)
1410 (q35)
1420 (q35)
1520 (q45)
1520 (q45)
1531 (q45)
1520 (q45)
1531 (q45)
1.5kW
2.2kW
1220 (q25)
1210 (q25)
0.4kW
1510 (q45)
3.0kW
1521 (q45)
1632 (q55)
3.7kW
1521 (q45)
1632 (q55)
5.5kW
Note 4
For inverters
0.25kW
1120 (q20)
1522 (q45)
1633 (q55)
15W
03 (q15)
25W
03 (q15)
40W
07 (q15)
60W
✽ 17 (q15)
90W
✽ 17 (q15)
0.1kW
1110 (q20)
1120 (q20)
1220 (q25)
0.2kW
1210 (q25)
1220 (q25)
1320 (q30)
0.4kW
1310 (q30)
1320 (q30)
1420 (q35)
0.1kW
1110 (q20)
1120 (q20)
1220 (q25)
0.2kW
1210 (q25)
1220 (q25)
1320 (q30)
0.4kW
1310 (q30)
1320 (q30)
1420 (q35)
0.75kW
1410 (q35)
1420 (q35)
1520 (q45)
1.5kW
1510 (q45)
1520 (q45)
1531 (q45)
2.2kW
3.7kW
1521 (q45)
1522 (q45)
1632 (q 55)
1633 (q 55)
Note1 : Reduction ratio for 15W–90W is 1/7.5
Note2 : Frame sizes marked with ✽ have a torque limitation. Refer to the selection table for the details.
Note3 : Reduction ratio for 15W and 25W is 1/160.
Note4 : Increased safety motors conform to eG3 of Japanese Industrial Standards (JIS).
Note5 : Waterproof types of frame size 1120, 1220, 1320, 1420, and 1520 with reduction ratio 1/5 are not available.
8
Note 3
1/80
1/100
1/120
1/150
1/200
1/240
1/300
1/360
1/480
1/560
1/720
1/900
18.1
14.5
12.1
9.67
7.25
6.04
4.83
4.03
3.02
2.59
1.93
1.61
1/1200 1/1440
1.21
1.01
21.9
17.5
14.6
11.7
8.75
7.29
5.83
4.86
3.65
3.13
2.33
1.94
1.46
1.22
✽ 1240 (q25)
17 (q15)
✽ 17 (q15)
✽ 1240 (q25)
✽ 1240 (q25)
✽ 1230 (q25)
✽ 1340 (q30)
✽ 1340 (q30)
✽ 1330 (q30)
1440 (q35)
✽ 1440 (q35)
✽ 1330 (q30)
✽ 1440 (q35)
✽ 1440 (q35)
✽ 1430 (q35)
1540 (q45)
✽ 1540 (q 45)
1430 (q35)
1540 (q45)
✽ 1430 (q35)
1540 (q45)
1540 (q45)
✽ 1530 (q45)
1640 (q55)
1640 (q55)
✽ 1530 (q45)
1640 (q55)
✽ 1530 (q45)
1640 (q55)
1531 (q45)
1531 (q45)
1630 (q55)
1631 (q55)
1531 (q45)
1630 (q55)
✽ 1631 (q55)
1630 (q55)
✽ 1631 (q55)
1630 (q55)
✽ 1240 (q25)
17 (q15)
✽ 1240 (q25)
✽ 1340 (q30)
1440 (q35)
✽ 1440 (q35)
1540 (q45)
1330 (q30)
1430 (q35)
✽ 1640 (q55)
1530 (q45)
✽ 1340 (q30)
1440 (q35)
✽ 1440 (q35)
1540 (q45)
1330 (q30)
1430 (q35)
1630 (q55)
1630 (q55)
1440 (q35)
✽ 1340 (q30)
✽ 1440 (q35)
✽ 1440 (q35)
✽ 1540 (q45)
✽ 1640 (q55)
1530 (q45)
1531 (q45)
✽ 1240 (q25)
✽ 1340 (q 30)
✽ 1440 (q35)
✽ 1440 (q35)
✽ 1540 (q45)
1631 (q55)
✽ 1631 (q55)
9
frame size (q bore diameter)
Solid shaft flange mount type
Reduction ratio
Output speed (r/min)
Power supply
Motor spec.
1/7
1/10
1/12
1/15
1/20
1/25
1/30
1/40
1/50
1/60
50Hz
290
207
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
60Hz
350
250
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
Indoor
type
Water proof
type
15W
Increased safety eG3 (Without brake, 0.25,
0.55, and 1,1kW are excluded from eG3.)
Outdoor type
3-Phase
01 (q10)
40W
05 (q12)
60W
07 (q15)
90W
0.2kW
0.25kW
0.4kW
0.55kW
0.75kW
1.1kW
1.5kW
2.2kW
Water proof
type
Outdoor
type
Outdoor
type
Indoor type
Single-Phase
inverters
For
01 (q10)
25W
0.1kW
Note 5
Note 1
1/5
15 (q15)
1120 (q18)
1220 (q22)
1120 (q18)
1220 (q22)
1320 (q28)
1220 (q22)
1320 (q28)
1220 (q22)
1320 (q28)
1320 (q28)
1420 (q32)
1320 (q28)
1420 (q32)
1320 (q28)
1420 (q32)
1420 (q32)
1520 (q40)
1420 (q32)
1520 (q40)
1420 (q32)
1520 (q40)
1520 (q40)
1531 (q40)
1520 (q40)
1531 (q40)
15W
01 (q10)
25W
01 (q10)
40W
05 (q12)
60W
15 (q15)
90W
15 (q15)
0.1kW
1120 (q18)
1220 (q22)
0.2kW
1220 (q22)
1320 (q28)
0.4kW
1320 (q28)
1420 (q32)
0.1kW
1120 (q18)
1220 (q22)
0.2kW
1220 (q22)
1320 (q28)
0.4kW
1320 (q28)
1420 (q32)
0.75kW
1420 (q32)
1520 (q40)
1.5kW
1520 (q40)
1220
1531
bore
diameter
(q40)25
Note1 : Reduction ratio for 15W–90W is 1/7.5
Note2 : Frame sizes marked with ✽ have a torque limitation. Refer to the selection table for the details.
Note3 : Reduction ratio for 15W and 25W is 1/160.
Note4 : Consult us as to selection table and dimension of the ratio 300 or more.
Note5 : Increased safety motors conform to eG3 of Japanese Industrial Standards (JIS).
10
1220 (q22)
Note 3
1/80
1/100
1/120
1/150
1/200
1/240
18.1
14.5
12.1
9.67
7.25
6.04
21.9
17.5
14.6
11.7
8.75
7.29
03 (q15)
03 (q15)
07 (q15)
17 (q18)
✽ 17 (q18)
✽ 17 (q18)
✽ 1230 (q22)
✽ 1330 (q28)
✽ 1330 (q28)
✽ 1430 (q32)
1430 (q32)
✽ 1430 (q32)
✽ 1530 (q40)
✽ 1530 (q40)
✽ 1530 (q40)
1531 (q40)
1531 (q40)
1531 (q40)
03 (q15)
03 (q15)
07 (q15)
17 (q18)
✽ 17 (q18)
✽ 17 (q18)
1330 (q28)
1430 (q32)
1530 (q40)
1330 (q28)
1430 (q32)
1530 (q40)
1531 (q40)
11
frame size (q bore diameter)
Solid shaft foot mount type
Reduction ratio
Output speed (r/min)
Power supply
Motor spec.
1/5
1/7
1/10
1/12
1/15
1/20
1/25
1/30
1/40
1/50
1/60
50Hz
290
207
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
60Hz
350
250
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
Increased safety eG3 (Without brake,
0.25, 0.55, and 1,1kW are excluded from eG3.)
3-Phase
Outdoor type
0.1kW
type
Indoor
type
Outdoor
Outdoor type
For
inverters
SinglePhase
Note 3
0.2kW
0.25kW
0.4kW
0.55kW
0.75kW
1.1kW
1.5kW
1120 (q18)
1220 (q22)
1120 (q18)
1220 (q22)
1220 (q22)
1320 (q28)
1220 (q22)
1320 (q28)
1220 (q22)
1320 (q28)
1320 (q28)
1420 (q32)
1320 (q28)
1420 (q32)
1320 (q28)
1420 (q32)
1420 (q32)
1520 (q40)
1420 (q32)
1520 (q40)
1420 (q32)
1520 (q40)
1520 (q40)
1531 (q40)
2.2kW
1520 (q40)
1531 (q40)
0.1kW
1120 (q18)
1220 (q22)
0.2kW
1220 (q22)
1320 (q28)
0.4kW
1320 (q28)
1420 (q32)
0.1kW
1120 (q18)
1220 (q22)
0.2kW
1220 (q22)
1320 (q28)
0.4kW
1320 (q28)
1420 (q32)
0.75kW
1420 (q32)
1520 (q40)
1.5kW
1520 (q40)
1531 (q40)
Note1 : Frame sizes marked with ✽ have a torque limitation. Refer to the selection table for the details.
Note2 : Consult us as to selection table and dimension of the ratio 300 or more.
Note3 : Increased safety motors conform to eG3 of Japanese Industrial Standards (JIS).
12
1/80
1/100
1/120
1/150
1/200
1/240
18.1
14.5
12.1
9.67
7.25
6.04
21.9
17.5
14.6
11.7
8.75
7.29
✽ 1230 (q22)
✽ 1330 (q28)
✽ 1330 (q28)
✽ 1430 (q32)
1430 (q32)
✽ 1430 (q32)
✽ 1530 (q40)
✽ 1530 (q40)
✽ 1530 (q40)
1531 (q40)
1531 (q40)
1531 (q40)
1330 (q28)
1430 (q32)
1530 (q40)
1330 (q28)
1430 (q32)
1530 (q40)
1531 (q40)
13
Standard specification
Standard Specifications
15W-5.5kW
4-pole
Housing
structure
15W-90W : IP44 (Indoor)
Totally-enclosed non-ventilated type
0.1kW and above : IP55
Totally-enclosed fan-cooled type
(0.1kW model : Totally-enclosed non ventilated type)
Power supply 15W-90W : 220V 50Hz, 220V 60Hz, 230V 50Hz
0.1kW-3.7kW :
220V-240V 50Hz , 220V 60Hz
380V-420V 50Hz
5.5kW :
380V-420V 50Hz
440V-480V 60Hz
Y
Y
Motor
Y
Time rating
Starting
method
Lead wire
(Lug type)
Standard
15W-90kW 4-pole : Class E
0.1kW-5.5kW 4-pole : Class F
Continuous
15W-3.7kW : Direct
5.5kW : - Starting
15-90W : 3-wire
0.1kW-5.5kW : 6-wire
15W-90W : JIS
0.1kW-5.5kW : IEC
Induction
Capacity range
15W-0.4kW
4-pole
IP44 (indoor) Totally-enclosed fan-cooled type
(15W, 25W, and 40W for #17:
Totally-enclosed non-ventilated type)
Power supply 230V 50Hz
Insulation 15W-90W 4-pole: Class E
0.1-0.4kW 4-pole: Class B
Time rating Continuous
15W-90W 4-pole: capacitor-run type
Starting
0.1-0.4kW 4-pole:
method
capacitor-starting capacitor-run type
Lead wire 15W-90W 4-pole: 3-wire
(Lug type) 0.1-0.4kW 4-pole: 6-wire
Standard
JIS
Capacity range
0.1-3.7kW 4-pole
3-phase for inverters
Single-phase
Housing
structure
Reducer
Ambient
conditions
Housing
structure
Power supply
Insulation
Time rating
Lead wire
(Lug type)
Standard
Lubrication
Reduction
Material
Installation
Temperature
Humidity
Altitude
Atomosphere
Installation angle
Painting
Y
3-phase
Y
Insulation
Specifications for motors with brake
15W-5.5kW 4-pole
SB, FB Brake (Non-asbestos lining)
15W-90W : IP44 (Indoor)
Totally-enclosed non-ventilated type
0.1kW and above : IP55
Totally-enclosed fan-cooled type
(0.1kW model : Totally-enclosed non ventilated type)
15W-90W : 220V 50Hz, 220V 60Hz, 230V 50Hz
0.1kW-3.7kW :
220V-240V 50Hz , 220V 60Hz
380V-420V 50Hz
(Brake : 220VAC-240VAC)
5.5kW :
380V-420V 50Hz
440V-480V 60Hz
(Brake : 380VAC-480VAC)
15W-90kW 4-pole : Class E (Brake insulation : Class B)
0.1kW-5.5kW 4-pole : Class F (Brake insulation : Class F)
Continuous
15W-3.7kW : Direct
5.5kW : - Starting
15-90W : 5-wire
0.1kW-5.5kW : 8-wire
15W-90W : JIS
0.1kW-5.5kW : IEC
Induction
Y
Y
Item
Capacity range
Y
Type
Reversible
15W-90W
4-pole
IP44 (indoor) Totally-enclosed fan-cooled type
(15W, 25W, and 40W for #17:
Totally-enclosed non-ventilated type)
100V 50/60Hz
15W-90W 4-pole: Class E
30 minutes
capacitor-run type
15W-0.4kW 4-pole, Brake: non-asbestos lining
IP44 (indoor) Totally-enclosed fan-cooled type
(40W for #17: Totally-enclosed non-ventilated type)
230V 50Hz
15W-90W 4-pole: Class E (Brake insulation: Class B)
0.1-0.4kW 4-pole: Class B (Brake insulation: Class B)
Continuous
15W-90W 4-pole: capacitor-run type
0.1-0.4kW 4-pole: capacitor-starting capacitor-run type
IP44 (indoor or outdoor)
Totally-enclosed fan-cooled type
380V 60Hz, 400V 60Hz, 415V 60Hz
Class F
Continuous rating (6–60Hz Torque constant)
15W-90W 4-pole: 5-wire
0.1-0.4kW 4-pole: 8-wire
JIS
0.1-3.7kW 4-pole
FB Brake (Non-asbestos lining)
IP44 (indoor or outdoor)
Totally-enclosed fan-cooled type
380V 60Hz, 400V 60Hz, 415V 60Hz
Class F (Brake insulation: Type F)
Continuous rating (6–60Hz Torque constant)
0.1-3.7kW 4-pole: 6-wire
0.1-3.7kW 4-pole: 8-wire
IEC
IEC
Grease lubrication: Filled with special high-grade grease prior to shipment
Combination of hypoid gear and involute gear
Casing: Aluminum alloy (#60, #63 and #64: Cast iron), Gear: Chrome-molybdenum steel
Indoor (Free from dust and water)
–10-40˚C
85%max. no dewing
1000m max.
Free from corrosive gas,explosive gas,or steam and well ventilated.
No limitation
Refer to page 183
Notes : 1. Refer to page 158 for mounting direction of a terminal box. (No terminal box for standard 15-90W models)
2. Refer to page 140–142 for output shaft rotation.
3. Refer to page 154–156 and 159–162 for the motor characteristics, brake specifications.
14
Nomenclature
R
N
Y
M
01
– 1010
–
Product
R
–
Shaft Spec.
Symbol
Metric Size
Blank
Hyponic
Inch Size
AGMA 1
Output shaft direction
Universal
N
–
B
5
Reduction ratio
Brake
Y
YA
Blank
Without brake
AGMA 2
YB
B
With brake
AGMA 3
YC
Mounting
Y
Hollow
F
Flange
H
Foot
Suffix
Solid shaft options
X1
Input Connection
M
Motor spec.
Plug-in shaft
Blank
With 3-phase motor
CA
With Single-Phase
Capacitor Start Motor
CB
With Single-Phase
Capacitor Start
Capacitor-Run
CC
With single-phase
reversible motor
AV
Motor for inverter
Integral motor
Extended flange, Left
(Viewed from motor)
P1
Input Power
Hyponic frame size
Extended flange, Right
(Viewed from motor)
0015
15W
01
03
0025
25W
05
07
004
40W
15
17
006
60W
1010
1110
009
90W
1120
1210
01
0.1kW
1220
1230
02
0.2kW
1310
1320
03
0.25kW
1330
1340
1410
05
0.4kW
1420
1430
1440
08
0.55kW
1510
1520
1521
1
0.75kW
1530
1531
1540
1H
1.1kW
1630
1631
2
1.5kW
1632
1633
3
2.2kW
1640
4
3.0kW
5
3.7kW
8
5.5kW
Y
Q1
Bolt on feet
1240
J1
1522
Shaft direction
Code
Viewed
from
motor
Blank
–
L
Left
R
Right
T
Both
F
RNYM Series
Hollow shaft type
RNFM Series
Flange mount type(1)
Viewed
from
above
H
RNFM Series
Flange mount type(2)
RNHM Series
Foot mount type
15
Memo
http://www.sumitomodrive.com
16
Hollow Shaft
17
Motors for
Inverters
Singlephase
3-phase
Hollow Shaft
15
15W 3-phase Motor
W
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
290
193
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
18.1
14.5
12.1
9.06
7.25
6.04
60Hz
350
233
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
21.9
17.5
14.6
10.9
8.75
7.29
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.371
0.307 0.038
0.031
0.556
0.461 0.057
0.047
0.742
0.615 0.076
0.063
0.890
0.738 0.091
0.075
1.11
0.922 0.113
0.094
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.23
1.84
0.227
0.188
2.97
2.46
0.303
0.251
3.71
3.07
0.378
0.313
4.45
3.69
0.454
0.376
5.93
4.92
0.605
0.501
7.42
6.15
0.756
0.627
8.90
7.38
0.908
0.752
11.9
9.83
1.21
1.00
14.8
12.3
1.51
1.25
17.8
14.8
1.82
1.50
Motor
Speed n1
Allowable Pro
SF
N
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
3.34
2.50
2.00
1.67
kgf
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1080
1080
1080
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1080
1080
1080
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
110
110
110
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
110
110
110
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM0015–03–5~240
Mass 2.6kg
Fig. 1
(RNYM0015–03–B–5~240)
(Mass 3.2kg)
175 (214)
82
135 (174)
2
L=300
8
5
17.3
A
15.6
2
40
28
80)
23.1
A
15H8
94
76 (
28
15
80
R1
78
A-A
4- 5.5
80
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
18
3. Dimentions and Masses in the drawings are subject to change
without notice.
25W 3-phase Motor
25
RNYM Series Hollow Shaft Type
60Hz
350
233
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
21.9
17.5
14.6
10.9
8.75
7.29
Allowable Pro
SF
N
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.00
1.50
1.20
1.00
kgf
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1080
1080
1080
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1080
1080
1080
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
110
110
110
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
110
110
110
1450r/min
1750r/min
W
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
Hollow Shaft
50Hz
290
193
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
18.1
14.5
12.1
9.06
7.25
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.618
0.512 0.063
0.052
0.927
0.768 0.095
0.078
1.24
1.02
0.126
0.104
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.47
2.05
0.252
0.209
3.09
2.56
0.315
0.261
3.71
3.07
0.378
0.313
4.95
4.10
0.504
0.418
6.18
5.12
0.630
0.522
7.42
6.15
0.756
0.627
9.89
8.20
1.01
0.836
12.4
10.2
1.26
1.04
14.8
12.3
1.51
1.25
19.8
16.4
2.02
1.67
24.7
20.5
2.52
2.09
29.7
24.6
3.03
2.51
50Hz
60Hz
2
3-phase
Output speed n2
r/min
Motor
Speed n1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM0025–03–5~240
Mass 2.7kg
Fig. 2
(RNYM0025–03–B–5~240)
(Mass 3.3kg)
175 (214)
82
135 (174)
2
L=300
8
5
17.3
A
15.6
2
40
28
80)
23.1
A
15H8
94
76 (
28
15
80
R1
78
A-A
4- 5.5
80
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
19
40
40W 3-phase Motor
W
RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.12
0.929 0.114
0.095
1.68
1.39
0.171
0.142
2.24
1.86
0.229
0.189
2.69
2.23
0.274
0.227
3.36
2.79
0.343
0.284
4.48
3.72
0.457
0.379
5.61
4.64
0.572
0.474
6.73
5.57
0.686
0.568
8.97
7.43
0.914
0.758
11.2
9.29
1.14
0.947
13.5
11.1
1.37
1.14
17.9
14.9
1.83
1.52
22.4
18.6
2.29
1.89
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
44.8
37.2
4.57
3.79
53.8
44.6
5.49
4.55
Output speed n2
r/min
50Hz
290
193
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
18.1
14.5
12.1
9.67
7.25
6.04
60Hz
350
233
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
21.9
17.5
14.6
11.7
8.75
7.29
Motor
Speed n1
Allowable Pro
SF
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1420
1420
1420
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.20
1.00
1.60
1.20
1.00
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1420
1420
1420
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
145
145
145
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
07
07
07
07
07
07
07
07
07
07
07
07
07
07
17
17
17
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM004–07–5~120
Mass 2.9kg
Fig. 1
(RNYM004–07–B–5~120)
(Mass 3.5kg)
180 (219)
45
82
135 (174)
6
17.3
5
23.1
A
2
15.6
2
L=300
28
28
15H8
76 (
90
18
80)
R1
104
A
78
A-A
4- 6.5
90
Mass 3.7kg
(Mass 4.1kg)
A
8
5
17.3
2
15.6
2
194 (253)
149 (208)
45
98
L=300
90
18
96)
R1
28
28
15H8
A
104
90 (
RNYM004–17–150~240
(RNYM004–17–B–150~240)
23.1
Fig. 2
94
A-A
4- 6.5
90
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
20
3. Dimentions and Masses in the drawings are subject to change
without notice.
40W 3-phase Motor
40
Output speed n2
r/min
50Hz
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
60Hz
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
5.35
6.46
52.5
63.3
6.42
7.75
62.9
76.0
8.56
10.0
83.9
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
Allowable Pro
SF
N
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
1.55
1.29
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
60Hz
185
185
185
185
185
185
185
185
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
004 —1240 — 300
004 —1240 — 360
004 —1240 — 480
004 —1240 — 600
3
004 —1240 — 720
004 —1240 — 900
004 —1240 — 1200
004 —1240 — 1440
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Fig. 3
kgf
W
Hollow Shaft
RNYM Series Hollow Shaft Type
50Hz 1450r/min
60Hz 1750r/min
3-phase
Motor 1
Speed n
Designate model, voltage, and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM004–1240–300~1440
Mass 6.5kg
(RNYM004–1240–B–300~1440)
(Mass 6.9kg)
262
211
51
φ25.6
A
φ25H8
100
90
51
9
B
40
38
127
R
1.
28.3
5
φ26.2
38
65
8
1.35
76
22
A
A-A
４-φ9
65
40
127
Without brake
321
73
82
∼B
9
96
40
65
4-φ9
9
127
B
51
A
φ14
9
270
51
5
76
41
φ78h7
41
φ78h7
5
A
40
65
127
With brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
21
60
W
60W 3-phase Motor
RNYM Series Hollow Shaft Type
Output Torque Tout
kgf m
kgf m
50Hz
60Hz
50Hz
60Hz
1.68
1.39
0.171
0.142
2.52
2.09
0.257
0.213
3.36
2.79
0.343
0.284
4.04
3.34
0.412
0.341
5.04
4.18
0.514
0.426
6.73
5.57
0.686
0.568
8.41
6.97
0.857
0.710
10.1
8.36
1.03
0.852
13.5
11.1
1.37
1.14
16.8
13.9
1.71
1.42
20.2
16.7
2.06
1.70
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
Output speed n2
r/min
50Hz
290
193
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
18.1
14.5
12.1
9.67
7.25
6.04
60Hz
350
233
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
21.9
17.5
14.6
11.7
8.75
7.29
Motor
Speed n1
Allowable Pro
SF
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1420
1420
1420
1420
1420
1420
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.50
1.50
1.34
1.07
✻
✻
50Hz
55
60
65
70
75
80
85
90
100
110
110
145
145
145
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1370
1420
1420
1420
1420
1420
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
105
110
140
145
145
145
145
145
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
07
07
07
07
07
07
07
07
07
07
07
17
17
17
17
17
17
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
2. Allowable radial load shows the value when the distance from hollow
capacity.
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM006–07–5~60
Mass 2.9kg
Fig. 1
(RNYM006–07–B–5~60)
(Mass 3.5kg)
180 (219)
45
82
135 (174)
6
17.3
5
23.1
A
2
15.6
2
L=300
28
28
15H8
76 (
90
18
80)
R1
104
A
78
A-A
4- 6.5
90
Mass 3.9kg
(Mass 4.3kg)
A
8
5
17.3
2
15.6
2
194 (253)
149 (208)
45
98
L=300
90
18
96)
R1
28
28
15H8
A
104
90 (
RNYM006–17–80~240
(RNYM006–17–B–80~240)
23.1
Fig. 2
94
A-A
4- 6.5
90
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
22
3. Dimentions and Masses in the drawings are subject to change
without notice.
60W 3-phase Motor
60
Output speed n2
r/min
50Hz
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
60Hz
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
8.02
9.68
78.7
95.0
9.63
10.0
94.4
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
Allowable Pro
SF
N
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
1.03
✻
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
60Hz
185
185
185
185
185
185
185
185
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
006 —1240 — 300
006 —1240 — 360
006 —1240 — 480
006 —1240 — 600
3
006 —1240 — 720
006 —1240 — 900
006 —1240 — 1200
006 —1240 — 1440
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Fig. 3
kgf
W
Hollow Shaft
RNYM Series Hollow Shaft Type
50Hz 1450r/min
60Hz 1750r/min
3-phase
Motor 1
Speed n
Designate model, voltage, and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM006–1240–300~1440
Mass6.7kg
(RNYM006–1240–B–300~1440)
(Mass 7.1kg)
262
211
51
φ25.6
A
φ25H8
100
90
51
9
B
40
38
127
R
1.
28.3
5
φ26.2
38
65
8
1.35
76
22
A
A-A
４-φ9
65
40
127
Without brake
321
73
82
∼B
9
96
40
65
4-φ9
9
127
B
51
A
φ14
9
270
51
5
76
41
φ78h7
41
φ78h7
5
A
40
65
127
With brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
23
90
90W 3-phase Motor
W
RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
2.09
2.52
0.257
0.213
3.13
3.78
0.386
0.320
4.18
5.04
0.514
0.426
5.02
6.05
0.617
0.511
6.27
7.57
0.772
0.639
8.36
10.1
1.03
0.852
10.4
12.6
1.29
1.07
12.5
15.1
1.54
1.28
20.2
16.7
2.06
1.70
25.2
20.9
2.57
2.13
30.3
25.1
3.09
2.56
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
50.2
5.50
5.11
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
Output speed n2
r/min
60Hz
350
233
175
146
117
87.5
70.0
58.3
43.8
35.0
29.2
21.9
17.5
14.6
11.7
8.75
7.29
Allowable Pro
N
SF
50Hz
637
686
785
834
883
981
1030
1080
1180
1270
1320
1420
1420
1420
1420
1420
1420
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
✻
✻
✻
✻
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
60Hz
588
637
735
785
834
932
981
1030
1130
1230
1270
1370
1420
1420
1420
1420
1420
50Hz
65
70
80
85
90
100
105
110
120
130
135
145
145
145
145
145
145
60Hz
60
65
75
80
85
95
100
105
115
125
130
140
145
145
145
145
145
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM009–17–5~240
Mass 4.2kg
(RNYM009–17–B–5~240)
(Mass 4.6kg)
A
8
5
17.3
2
15.6
2
194 (253)
149 (208)
45
98
L=300
90
18
96)
R1
28
28
15H8
A
104
90 (
Fig. 1
kgf
23.1
50Hz
290
193
145
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
18.1
14.5
12.1
9.67
7.25
6.04
Motor
Speed n1
94
A-A
4- 6.5
90
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
24
3. Dimentions and Masses in the drawings are subject to change
without notice.
90W 3-phase Motor
90
RNYM Series Hollow Shaft Type
60Hz
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
Allowable Pro
SF
N
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
✻
✻
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
60Hz
185
185
185
185
185
185
185
185
W
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
009
009
009
009
009
009
009
009
— 1240
— 1240
— 1240
— 1240
— 1240
— 1240
— 1240
— 1240
— 300
— 360
— 480
— 600
— 720
— 900
— 1200
— 1440
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Fig. 2
kgf
1450r/min
1750r/min
Hollow Shaft
50Hz
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
50Hz
60Hz
3-phase
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM009–1240–300~1440
Mass 7.0kg
(RNYM009–1240–B–300~1440)
(Mass 7.4kg)
262
211
51
φ25.6
A
φ25H8
100
90
51
9
B
40
38
127
R
1.
28.3
5
φ26.2
38
65
8
1.35
76
22
A
A-A
４-φ9
65
40
127
Without brake
321
73
82
∼B
9
96
40
65
4-φ9
9
127
B
51
A
φ14
9
270
51
5
76
41
φ78h7
41
φ78h7
5
A
40
65
127
With brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
25
0.1
0.1kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Motor
Speed n1
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
2.80
2.32
0.286
0.237
Output speed n2
r/min
50Hz
290
60Hz
350
207
250
3.92
3.25
0.400
0.332
145
175
5.61
4.64
0.572
0.474
121
96.7
72.5
58.0
48.3
36.3
146
117
87.5
70.0
58.3
43.8
6.73
8.41
11.2
14.0
16.8
22.4
5.57
6.97
9.29
11.6
13.9
18.6
0.686
0.857
1.14
1.43
1.71
2.29
0.568
0.710
0.947
1.18
1.42
1.89
29.0
35.0
28.0
23.2
2.86
2.37
24.2
29.2
33.6
27.9
3.43
2.84
Allowable Pro
SF
N
kgf
50Hz
539
637
588
686
637
785
834
883
981
1030
1080
1180
1620
1270
1720
1320
1770
2.00
2.00
2.00
2.00
1.00
2.00
2.00
2.00
2.00
2.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
60Hz
490
588
539
637
588
735
785
834
932
981
1030
1130
1570
1230
1670
1270
1720
50Hz
55
65
60
70
65
80
85
90
100
105
110
120
165
130
175
135
180
60Hz
50
60
55
65
60
75
80
85
95
100
105
115
160
125
170
130
175
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1010
1120
1010
1120
1010
1120
1120
1120
1120
1120
1120
1120
1220
1120
1220
1120
1220
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
5
7
7
10
10
12
15
20
25
30
40
40
50
50
60
60
1
2
1
2
1
2
2
3
2
3
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1010–5~10
Mass 5.0kg
Fig. 1
(RNYM01–1010–B–5~10)
(Mass 6.5kg)
223 (258)
32
6
9
64
32
32
25 25
28
82
A
15H8
4- 6.6
A-A
25
25
64
64
9
RNYM01–1120–5~60
(RNYM01–1120–B–5~60)
Fig. 2
1.5
Mass 6.0kg
(Mass 7.5kg)
268 (303)
90
33
33
40
6
82
16
20.6
A
40
32
42
90
20
30
50
R
1
22.8
6
21
52h7
52h7
1.15
30
20H8
82
A
4- 6.6
A-A
32
128
6
42
88
8
66
22
8
RNYM01–1220–40~60
(RNYM01–1220–B–40~60)
Fig. 3
119 ( 124)
9
119( 124)
A
1
17.3
48h7
48h7
15.6
5
R
28
45
128
90
32
32
6
Mass 7.0kg
(Mass 8.5kg)
291 (326)
A
119 ( 124)
57
38
25H8
A-A
A
4- 9
40
57
113
5
37
128
92
40
49
66
38
115
5
1.
R
28
8
26.2
78h7
78h7
1.35
96
49
22
9
28.3
74
25.6
9
20
37
90
26
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.1kW 3-phase Motor
0.1
RNYM Series Hollow Shaft Type
50Hz
18.1
60Hz
21.9
14.5
17.5
56.1
46.4
5.72
4.74
12.1
14.6
67.3
55.7
6.86
5.68
11.7
84.1
69.7
8.57
7.10
98.1
112
98.1
135
92.9
92.9
98.1
111
9.67
7.25
8.75
6.04
7.29
10.0
11.4
10.0
13.7
Allowable Pro
SF
N
50Hz
1770
3040
1810
3090
1810
3090
1810
3090
1810
3090
1810
3090
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
✻
1.74
✻
1.45
9.47
9.47
10.0
11.4
kgf
60Hz
1770
2940
1770
3040
1810
3090
1810
3090
1810
3090
1810
3090
50Hz
180
310
185
315
185
315
185
315
185
315
185
315
60Hz
180
300
180
310
185
315
185
315
185
315
185
315
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
01
01
01
01
01
01
01
01
01
01
01
01
—
—
—
—
—
—
—
—
—
—
—
—
1230
1330
1230
1330
1230
1330
1230
1330
1230
1330
1230
1330
—
—
—
—
—
—
—
—
—
—
—
—
80
80
100
100
120
120
150
150
200
200
240
240
4
5
4
5
4
5
4
5
4
5
4
5
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kW
Hollow Shaft
Output speed n2
r/min
50Hz
60Hz
3-phase
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
44.8
37.2
4.57
3.79
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1230–80~240
Mass 7.5kg
(RNYM01–1230–B–80~840)
(Mass 9.0kg)
Fig. 4
292 (327)
51
5
95
A
73
25.6
38
25H8
38
13
76
65
.5
R1
127
28.3
51
40
8
26.2
78h7
78h7
22
1.35
128
100
14
A-A
4- 9
A
40
(
9
90)
82
65
127
9
RNYM01–1330–80~240
(RNYM01–1330–B–80~840)
Fig. 5
119 ( 124)
41
90
41
5
8
Mass 9.0kg
(Mass 10kg)
314 (349)
46
46
60
5
81
11
119 ( 124)
60
47
33.3
30H8
92
79
46
152
.5
R1
46
A
8
31.4
85h7
85h7
1.35
30.6
22
A
92
9
17.5
110
9
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
108
128
5
4- 11
47
79
152
3.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
27
0.1kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
158
131
16.1
13.4
Output speed n2
r/min
50Hz
4.83
60Hz
5.83
4.03
4.86
190
157
19.4
16.0
3.02
3.65
2.42
2.92
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
195
253
195
317
195
380
195
390
195
390
195
390
195
210
195
262
195
315
195
390
195
390
195
390
19.9
25.8
19.9
32.3
19.9
38.7
19.9
39.8
19.9
39.8
19.9
39.8
19.9
21.4
19.9
26.7
19.9
32.1
19.9
39.8
19.9
39.8
19.9
39.8
Motor
Speed n1
N
SF
50Hz
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
1.00
2.00
1.00
2.00
✻
1.54
✻
1.23
✻
1.03
✻
✻
✻
✻
✻
✻
50Hz
315
445
315
445
315
445
315
445
315
445
315
445
315
445
315
445
60Hz
315
445
315
445
315
445
315
445
315
445
315
445
315
445
315
445
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1340–300~1440
Mass 10kg
(RNYM01–1340–B–300~1440)
(Mass 11kg)
367
60
47
4-φ11
□90
60
47
79
4-φ11
152
47
26.5
128
79
152
Without brake
RNYM01–1440–300~1440
(RNYM01–1440–B–300~1440)
9
A
128
A
φ17.5
152
φ119
92
79
φ30H8
9
Fig. 2
□90
92
79
46
9
152
1.
R
46
131
A
60
47
8
5
φ31.4
φ85h7
φ85h7
1.35
110
A-A
81
92
125
60
A
22
9
372
131
5
33.3
46
φ30.6
46
26.5
With brake
Mass 14.5kg
(Mass 16kg)
414
409
70
A
φ20
10
105
118
125
4-φ14
Without brake
70
□90
11
92
44
54
92
178
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
28
A
4-φ14
92
178
108
φ119
54
54
□90
70
54
A
178
138
A-A
φ35H8
128
52
11
φ95h7
φ95h7
φ37
.5
R1
52
163
A
10
92
1.75
108
26
70
163
128
5
38.3
59
178
59
φ35.6
5
φ124
Fig. 1
5
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
1
01 — 1340 — 300
2
01 — 1440 — 300
1
01 — 1340 — 360
2
01 — 1440 — 360
1
01 — 1340 — 480
2
01 — 1440 — 480
1
01 — 1340 — 600
2
01 — 1440 — 600
1
01 — 1340 — 720
2
01 — 1440 — 720
1
01 — 1340 — 900
2
01 — 1440 — 900
1
01 — 1340 — 1200
2
01 — 1440 — 1200
1
01 — 1340 — 1440
2
01 — 1440 — 1440
kgf
60Hz
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
50Hz
60Hz
φ124
0.1
44
With brake
3. Dimensions and masses in the drawings are subject to change
without notice.
0.2kW 3-phase Motor
0.2
RNYM Series Hollow Shaft Type
60Hz
350
207
250
145
175
7.85
11.2
6.50
0.800
0.663
9.29
1.14
0.947
N
SF
kgf
50Hz
637
637
883
686
686
981
785
785
1080
2.00
1.00
2.00
2.00
1.00
2.00
1.00
1.00
2.00
60Hz
588
588
834
637
637
932
735
735
1030
50Hz
65
65
90
70
70
100
80
80
110
60Hz
60
60
85
65
65
95
75
75
105
50Hz
60Hz
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
02
02
02
02
02
02
02
02
02
—
—
—
—
—
—
—
—
—
1110
1120
1220
1110
1120
1220
1110
1120
1220
— 5
— 5
— 5
— 7
— 7
— 7
— 10
— 10
— 10
1
2
3
1
2
3
1
2
3
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Hollow Shaft
50Hz
290
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
5.61
4.64
0.572
0.474
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1110–5~10
Mass 6.0kg
(RNYM02–1110–B–5~10)
(Mass 7.5kg)
Fig. 1
275 (307)
90
A
16
30
29
4- 6.6
20H8
Mass 7.0kg
(Mass 8.5kg)
90
6
33
2
8
RNYM02–1120–5~10
(RNYM02–1120–B–5~10)
Fig. 2
29
74
A-A
128
A
82
66
124( 124)
11
37
29
1
R
30
29
6
21
52h7
52h7
1.15
8
50
74
6
37
33
22.8
33
20.6
6
37
33
310 (342)
6
40
82
A
40
32
50
42
20
30
20H8
82
A
4- 6.6
A-A
32
128
30
90
R
1
22.8
6
21
52h7
52h7
1.15
42
22
88
8
8
66
RNYM02–1220–5~10
(RNYM02–1220–B–5~10)
Fig. 3
124 ( 124)
20.6
16
Mass 8.5kg
(Mass 10kg)
333 (365)
28
124 ( 124)
66
38
25H8
A-A
A
4- 9
40
57
113
5
37
37
128
92
40
5
1.
57
26.2
78h7
8
R
38
96
A
49
1.35
78h7
49
22
115
9
28.3
74
25.6
9
20
5
90
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
29
0.2
0.2kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
60Hz
146
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
13.5
11.1
1.37
1.14
117
16.8
13.9
1.71
1.42
Output speed n2
r/min
50Hz
121
96.7
72.5
87.5
22.4
18.6
2.29
1.89
58.0
70.0
28.0
23.2
2.86
2.37
48.3
58.3
33.6
27.9
3.43
2.84
36.3
43.8
44.8
37.2
4.57
3.79
29.0
35.0
56.1
46.4
5.72
4.74
24.2
29.2
67.3
55.7
6.86
5.68
Motor
Speed n1
Allowable Pro
N
SF
kgf
50Hz
834
1130
883
1230
981
1370
1030
1470
1080
1520
1620
2650
1720
2840
1770
2940
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
60Hz
785
1080
834
1180
932
1320
981
1370
1030
1470
1570
2550
1670
2750
1720
2840
50Hz
85
115
90
125
100
140
105
150
110
155
165
270
175
290
180
300
60Hz
80
110
85
120
95
135
100
140
105
150
160
260
170
280
175
290
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
02
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1120
1220
1120
1220
1120
1220
1120
1220
1120
1220
1220
1320
1220
1320
1220
1320
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
12
12
15
15
20
20
25
25
30
30
40
40
50
50
60
60
4
5
4
5
4
5
4
5
4
5
5
6
5
6
5
6
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1120–12~30
Mass 7.0kg
(RNYM02–1120–B–12~30)
(Mass 8.5kg)
Fig. 4
90
6
33
310 (342)
33
6
40
82
A
40
32
42
90
20
30
20H8
82
A
4- 6.6
A-A
32
128
30
50
R
1
22.8
6
21
52h7
52h7
1.15
42
22
88
8
8
66
RNYM02–1220–12~60
(RNYM02–1220–B–12~60)
Fig. 5
124 ( 124)
20.6
16
Mass 8.5kg
(Mass 10kg)
333 (365)
49
22
A
49
38
124 ( 124)
115
66
25H8
92
A-A
128
38
40
5
1.
R
28
8
26.2
78h7
78h7
1.35
96
57
9
28.3
74
25.6
9
A
4- 9
40
57
113
5
37
37
20
5
90
RNYM02–1320–40~60
(RNYM02–1320–B–40~60)
Mass 10kg
(Mass 11kg)
112
5
46
46
361 (393)
58
5
A
30.6
22
58
46
128
46
110
132
74
62
33.3
5
1.
R
46
27.5
8
31.4
85h7
1.35
85h7
119
30H8
124 ( 124)
Fig. 6
A
A-A
4- 11
46
9
30
92
9
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
62
130
34
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.2kW 3-phase Motor
0.2
RNYM Series Hollow Shaft Type
14.5
17.5
112
12.1
14.6
135
111
13.7
11.4
11.7
168
139
17.1
14.2
195
224
195
269
186
186
195
223
19.9
22.9
19.9
27.4
18.9
18.9
19.9
22.7
9.67
7.25
8.75
6.04
7.29
92.9
11.4
SF
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
✻
1.74
✻
1.45
9.47
N
50Hz
3040
4360
3090
4360
3090
4360
3090
4360
3090
4360
3090
4360
50Hz
310
445
315
445
315
445
315
445
315
445
315
445
60Hz
300
435
310
445
315
445
315
445
315
445
315
445
02
02
02
02
02
02
02
02
02
02
02
02
—
—
—
—
—
—
—
—
—
—
—
—
1330
1430
1330
1430
1330
1430
1330
1430
1330
1430
1330
1430
—
—
—
—
—
—
—
—
—
—
—
—
80
80
100
100
120
120
150
150
200
200
240
240
1
2
1
2
1
2
1
2
1
2
1
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
2940
4270
3040
4360
3090
4360
3090
4360
3090
4360
3090
4360
1450r/min
1750r/min
Hollow Shaft
60Hz
21.9
Allowable Pro
50Hz
60Hz
3-phase
50Hz
18.1
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
89.7
74.3
9.14
7.58
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1330–80~240
Mass 10kg
(RNYM02–1330–B–80~240)
(Mass 11kg)
Fig. 1
356 (388)
5
46
46
60
5
81
A
11
60
47
30H8
46
128
124 ( 124)
46
152
.5
R1
92
79
33.3
8
31.4
85h7
85h7
1.35
30.6
22
A
17.5
110
9
92
A-A
4- 11
47
9
79
152
RNYM02–1430–80~240
(RNYM02–1430–B–80~240)
Fig. 2
108
3.5
Mass 15kg
(Mass 16kg)
384 (416)
5
70
130
35.6
A
14
124 ( 124)
35H8
128
52
108
92
52
178
φ37
.5
R1
70
54
10
38.3
26
1.75
95h7
59
59
105
95h7
5
20
138
10
118
A-A
10
4- 14
A
54
92
178
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
8
3. Dimentions and Masses in the drawings are subject to change
without notice.
31
0.2kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
26.7
32.3
262
317
Output speed n2
r/min
50Hz
4.83
60Hz
5.83
4.03
4.86
380
315
38.7
32.1
3.02
3.65
2.42
2.92
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
390
506
390
633
390
732
390
732
390
732
390
732
390
420
390
525
390
629
390
732
390
732
390
732
39.8
51.6
39.8
64.6
39.8
74.6
39.8
74.6
39.8
74.6
39.8
74.6
39.8
42.8
39.8
53.5
39.8
64.2
39.8
74.6
39.8
74.6
39.8
74.6
Motor
Speed n1
Allowable Pro
SF
N
50Hz
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
1.00
2.00
1.00
1.93
✻
1.44
✻
1.16
✻
✻
✻
✻
✻
✻
✻
✻
kgf
60Hz
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
50Hz
445
635
445
635
445
635
445
635
445
635
445
635
445
635
445
635
60Hz
445
635
445
635
445
635
445
635
445
635
445
635
445
635
445
635
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
3
02 — 1440 — 300
4
02 — 1540 — 300
3
02 — 1440 — 360
4
02 — 1540 — 360
3
02 — 1440 — 480
4
02 — 1540 — 480
3
02 — 1440 — 600
4
02 — 1540 — 600
3
02 — 1440 — 720
4
02 — 1540 — 720
3
02 — 1440 — 900
4
02 — 1540 — 900
3
02 — 1440 — 1200
4
02 — 1540 — 1200
3
02 — 1440 — 1440
4
02 — 1540 — 1440
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1440–300~1440
Mass 15.5kg
(RNYM02–1440–B–300~1440)
(Mass 17kg)
427
59
5
70
453
163
70
163
105
118
125
4-φ14
φ124
□90
11
108
92
128
54
A
4-φ14
92
178
10
178
11
A
54
44
92
178
Without brake
RNYM02–1540–300~1440
(RNYM02–1540–B–300~1440)
Fig.4
70
54
□90
70
54
108
92
52
φ20
138
A-A
A
178
52
38.3
10
.5
R1
φ35H8
φ37
φ95h7
φ95h7
1.75
φ35.6
A
26
128
59
44
With brake
Mass 24.5kg
(Mass 25.5kg)
471
4-φ18
136
64
109
4-φ18
54
128
14
A
64
109
213
54
10
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
32
213
84
64
A
213
10
φ124
128
14
φ45H8
84
64
1.
5
67
156
A-A
197
A
□112
A
R
67
84
14
φ47.5
φ110h7
φ110h7
1.95
129
109
30
497
197
□112
84
129
109
5
213
68
48.8
68
φ45.6
5
φ124
Fig. 3
10
1450r/min
1750r/min
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
5
50Hz
60Hz
φ124
0.2
With brake
3. Dimensions and masses in the drawings are subject to change
without notice.
0.25kW 3-phase Motor
0.25
RNYM Series Hollow Shaft Type
50Hz
290
60Hz
350
207
250
145
175
14.0
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
16.8
21.0
28.0
35.0
42.0
56.1
70.1
84.1
9.81
8.13
1.00
0.829
11.6
1.43
1.18
13.9
17.4
23.2
29.0
34.8
46.4
58.1
69.7
1.71
2.14
2.86
3.57
4.29
5.72
7.14
8.57
1.42
1.78
2.37
2.96
3.55
4.74
5.92
7.10
Allowable Pro
N
SF
3.20
1.60
3.20
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
1.60
60Hz
834
50Hz
90
60Hz
85
981
932
100
95
1080
1030
110
105
1130
1230
1370
1470
1520
2650
2840
2940
1080
1180
1320
1370
1470
2550
2750
2840
115
125
140
150
155
270
290
300
110
120
135
140
150
260
280
290
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
883
1450r/min
1750r/min
03
03
03
03
03
03
03
03
03
03
03
03
03
03
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1210
1220
1210
1220
1210
1220
1220
1220
1220
1220
1220
1320
1320
1320
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
5
7
7
10
10
12
15
20
25
30
40
50
60
1
2
1
2
1
2
Hollow Shaft
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
7.01
5.81
0.714
0.592
50Hz
60Hz
2
3
3-phase
Output speed n2
r/min
Motor
Speed n1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM03–1210–5~10
Mass 9.0kg
(RNYM03–1210–B–5~10)
(Mass 10kg)
Fig. 1
311 (343)
112
37
37
5
46
61
5
A
128
A
38
25H8
38
4- 9
92
37
37
92
A-A
9
124( 124)
28.3
R
14
46
37
5
1.
92
26.2
8
46
37
1.35
78h8
78h7
25.6
22
1.5
9
RNYM03–1220–5~30
(RNYM03–1220–B–5~30)
Fig. 2
Mass 9.5kg
(Mass 11kg)
353 (385)
49
22
A
28
115
38
25H8
92
A-A
A
4- 9
40
128
38
124 ( 124)
5
1.
R
40
49
25.6
8
26.2
78h7
78h7
1.35
96
57
9
66
74
28.3
9
57
113
5
37
37
20
5
90
RNYM03–1320–40~60
(RNYM03–1320–B–40~60)
Fig. 3
Mass 11kg
(Mass 13kg)
112
46
46
381 (413)
58
5
A
30.6
22
124 ( 124)
58
46
74
62
46
110
132
33.3
5
1.
R
46
27.5
8
31.4
85h7
1.35
85h7
119
30H8
128
5
A
A-A
4- 11
46
9
92
9
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
62
130
34
3. Dimentions and Masses in the drawings are subject to change
without notice.
33
0.25
0.25kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
9.47
92.9
11.4
112
11.8
116
14.3
140
14.2
139
17.1
168
17.8
174
21.4
210
23.7
232
28.6
280
28.4
279
34.3
336
33.4
328
40.3
396
40.1
393
48.4
475
53.5
64.6
525
633
66.9
74.6
656
732
74.6
74.6
732
732
74.6
74.6
732
732
74.6
74.6
732
732
74.6
74.6
732
732
Output speed n2
r/min
50Hz
18.1
14.5
12.1
9.67
7.25
6.04
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
Motor
Speed n1
60Hz
21.9
17.5
14.6
11.7
8.75
7.29
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
Allowable Pro
N
SF
60Hz
4270
4360
4360
4360
4360
4360
6230
6230
6230
6230
6230
6230
6230
6230
50Hz
445
445
445
445
445
445
635
635
635
635
635
635
635
635
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
03 — 1430 — 80
03 — 1430 — 100
03 — 1430 — 120
4
03 — 1430 — 150
03 — 1430 — 200
03 — 1430 — 240
03 — 1540 — 300
03 — 1540 — 360
03 — 1540 — 480
03 — 1540 — 600
5
03 — 1540 — 720
03 — 1540 — 900
03 — 1540 — 1200
03 — 1540 — 1440
kgf
50Hz
4360
4360
4360
4360
4360
4360
6230
6230
6230
6230
6230
6230
6230
6230
1.60
1.60
1.60
1.60
1.39
1.16
1.60
1.54
1.16
✻
✻
✻
✻
✻
50Hz
60Hz
60Hz
435
445
445
445
445
445
635
635
635
635
635
635
635
635
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM03–1430–80~240
Mass 16kg
(RNYM03–1430–B–80~240)
(Mass 17kg)
Fig. 4
404 (436)
59
59
105
5
70
130
A
35H8
52
124 ( 124)
178
128
52
108
92
38.3
.5
R1
14
70
54
10
37
95h7
35.6
26
1.75
95h7
5
138
A-A
20
118
4- 14
A
10
54
92
178
RNYM03–1540–300~1440
(RNYM03–1540–B–300~1440)
Fig. 5
8
Mass 26kg
(Mass 27.5kg)
491
84
4-φ18
10
136
□122
84
64
10
128
14
A
64
109
213
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
34
4-φ18
54
128
48.8
φ45H8
213
67
156
A-A
129
109
67
197
A
84
64
14
R1
.5
φ47.5
φ110h7
φ110h7
1.95
φ45.6
A
30
517
197
□122
84
14
5
213
68
129
109
68
φ124
5
φ124
10
A
64
109
213
54
With brake
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.4kW 3-phase Motor
0.4
RNYM Series Hollow Shaft Type
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
11.2
9.29
1.14
0.947
50Hz
290
60Hz
350
207
250
15.7
13.0
1.60
1.33
145
175
22.4
18.6
2.29
1.89
N
SF
50Hz
883
883
1470
981
981
1670
1080
1080
1810
2.00
1.00
2.00
2.00
1.00
2.00
1.00
1.00
2.00
50Hz
90
90
150
100
100
170
110
110
185
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
834
834
1370
932
932
1570
1030
1030
1720
50Hz
60Hz
60Hz
85
85
140
95
95
160
105
105
175
05
05
05
05
05
05
05
05
05
—
—
—
—
—
—
—
—
—
1210
1220
1320
1210
1220
1320
1210
1220
1320
— 5
— 5
— 5
— 7
— 7
— 7
— 10
— 10
— 10
1
2
3
1
2
3
1
2
3
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Hollow Shaft
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1210–5~10
Mass 9kg
(RNYM05–1210–B–5~10)
(Mass 10kg)
Fig. 1
311 (343)
112
37
37
5
46
61
5
A
128
A
38
25H8
38
4- 9
92
37
37
92
A-A
9
124( 124)
28.3
R
14
46
37
5
1.
92
26.2
8
46
37
1.35
78h8
78h7
25.6
22
1.5
9
RNYM05–1220–5~10
(RNYM05–1220–B–5~10)
Fig. 2
Mass 9.5kg
(Mass 11kg)
353 (385)
49
22
28
115
38
25H8
92
A-A
A
4- 9
40
128
38
124 ( 124)
5
1.
R
40
49
25.6
8
26.2
78h7
78h7
1.35
96
A
57
9
66
74
28.3
9
57
113
5
37
37
20
5
90
RNYM05–1320–5~10
(RNYM05–1320–B–5~10)
Fig. 3
Mass 11kg
(Mass 13kg)
112
46
46
381 (413)
58
5
A
30.6
22
124 ( 124)
58
46
74
62
46
110
132
33.3
1.
5
R
46
27.5
8
31.4
85h7
1.35
85h7
119
30H8
128
5
A
A-A
4- 11
46
9
92
9
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
62
130
34
3. Dimentions and Masses in the drawings are subject to change
without notice.
35
0.4
0.4kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
50Hz
121
96.7
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
26.9
22.3
2.74
2.27
Output speed n2
r/min
60Hz
146
117
33.6
27.9
3.43
2.84
72.5
87.5
44.8
37.2
4.57
3.79
58.0
70.0
56.1
46.4
5.72
4.74
48.3
58.3
67.3
55.7
6.86
5.68
36.3
43.8
89.7
74.3
9.14
7.58
29.0
35.0
112
24.2
29.2
135
92.9
11.4
111
N
SF
50Hz
1130
1910
1230
2060
1370
2260
1470
2350
1520
2450
2650
3970
2840
4170
2940
4310
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
9.47
13.7
Motor
Speed n1
11.4
50Hz
115
195
125
210
140
230
150
240
155
250
270
405
290
425
300
440
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
4
05 — 1220 — 12
5
05 — 1320 — 12
4
05 — 1220 — 15
5
05 — 1320 — 15
4
05 — 1220 — 20
5
05 — 1320 — 20
4
05 — 1220 — 25
5
05 — 1320 — 25
4
05 — 1220 — 30
5
05 — 1320 — 30
5
05 — 1320 — 40
6
05 — 1420 — 40
5
05 — 1320 — 50
6
05 — 1420 — 50
5
05 — 1320 — 60
6
05 — 1420 — 60
kgf
60Hz
1080
1810
1180
1960
1320
2160
1370
2260
1470
2350
2550
3820
2750
4020
2840
4170
50Hz
60Hz
60Hz
110
185
120
200
135
220
140
230
150
240
260
390
280
410
290
425
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1220–12~30
Mass 9.5kg
(RNYM05–1220–B–12~30)
(Mass 11kg)
Fig. 4
353 (385)
49
22
A
124 ( 124)
115
38
25H8
92
A-A
A
4- 9
40
128
38
28
49
5
1.
R
40
25.6
8
26.2
78h7
78h7
1.35
96
57
9
66
74
28.3
9
57
113
5
37
37
20
5
90
RNYM05–1320–12~60
(RNYM05–1320–B–12~60)
Fig. 5
Mass 11kg
(Mass 13kg)
112
46
381 (413)
46
58
5
119
A
30.6
22
27.5
124 ( 124)
58
46
74
62
46
132
33.3
1.
5
R
85h7
85h7
8
31.4
1.35
46
30H8
110
128
5
A
4- 11
A-A
46
9
Fig. 6
92
62
130
9
RNYM05–1420–40~60
(RNYM05–1420–B–40~60)
34
Mass 15kg
(Mass 16kg)
412 (444)
5
20
128
35H8
A
A-A
118
10
4- 14
57
75
155
36
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
124 ( 124)
52
138
70
57
.5
R1
52
A
10
37
95h7
95h7
1.75
88
75
26
10
146
70
158
59
38.3
59
35.6
5
43
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.4kW 3-phase Motor
0.4
RNYM Series Hollow Shaft Type
60Hz
21.9
14.5
17.5
224
186
22.9
18.9
12.1
14.6
269
223
27.4
22.7
11.7
336
279
34.3
28.4
390
448
390
538
372
372
390
446
39.8
45.7
39.8
54.9
37.9
37.9
39.8
45.5
9.67
7.25
8.75
6.04
7.29
SF
1.00
2.00
1.00
2.00
1.00
2.00
1.00
2.00
✻
1.63
✻
1.36
N
50Hz
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
50Hz
445
635
445
635
445
635
445
635
445
635
445
635
60Hz
435
625
445
635
445
635
445
635
445
635
445
635
05
05
05
05
05
05
05
05
05
05
05
05
—
—
—
—
—
—
—
—
—
—
—
—
1430
1530
1430
1530
1430
1530
1430
1530
1430
1530
1430
1530
—
—
—
—
—
—
—
—
—
—
—
—
80
80
100
100
120
120
150
150
200
200
240
240
1
2
1
2
1
2
1
2
1
2
1
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
4270
6130
4360
6230
4360
6230
4360
6230
4360
6230
4360
6230
1450r/min
1750r/min
Hollow Shaft
50Hz
18.1
Allowable Pro
50Hz
60Hz
3-phase
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
179
149
18.3
15.2
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1430–80~240
Mass 16kg
(RNYM05–1430–B–80~240)
(Mass 17kg)
Fig. 1
404 (436)
5
70
130
A
124 ( 124)
178
35H8
52
128
52
108
92
.5
R1
14
70
54
10
38.3
95h7
35.6
26
1.75
37
59
59
105
95h7
5
138
A-A
20
10
118
4- 14
10
A
54
92
178
Fig. 2
RNYM05–1530–80~240
(RNYM05–1530–B–80~240)
8
Mass 23kg
(Mass 24kg)
437 (469)
5
68
68
84
5
157
128
A
156
124 ( 124)
84
64
45H8
213
129
109
67
48.8
1.
5
R
67
17
14
47.5
110h7
110h7
1.95
45.6
A
30
A-A
10
136
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
4- 18
64
109
213
9.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
37
0.4
0.4kW 3-phase Motor
kW
3-phase Motor Indoor Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
633
525
64.6
53.5
732
629
74.6
64.2
732
732
74.6
74.6
732
732
74.6
74.6
732
732
74.6
74.6
732
732
74.6
74.6
732
732
74.6
74.6
732
732
74.6
74.6
Output speed n2
r/min
60Hz
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
Allowable Pro
N
SF
50Hz
6230
6230
6230
6230
6230
6230
6230
6230
1.00
✻
✻
✻
✻
✻
✻
✻
kgf
60Hz
6230
6230
6230
6230
6230
6230
6230
6230
50Hz
635
635
635
635
635
635
635
635
60Hz
635
635
635
635
635
635
635
635
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
05
05
05
05
05
05
05
05
—
—
—
—
—
—
—
—
1540
1540
1540
1540
1540
1540
1540
1540
491
84
4-φ18
10
64
109
213
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
213
84
64
4-φ18
54
128
128
14
A
129
109
48.8
213
φ45H8
129
109
R1
.5
67
156
A-A
84
64
14
197
A
□112
φ45.6
φ47.5
φ110h7
φ110h7
67
517
197
A
38
3
□112
84
1.95
136
300
360
480
600
720
900
1200
1440
14
5
φ124
68
30
10
—
—
—
—
—
—
—
—
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1540–300~1440
Mass 26kg
(RNYM05–1540–B–300~1440)
(Mass 27.5kg)
Fig. 3
68
1450r/min
1750r/min
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
5
50Hz
60Hz
φ124
50Hz
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
Motor
Speed n1
A
64
109
213
54
With brake
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.55kW 3-phase Motor
0.55
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.30
1.57
12.8
15.4
50Hz
290
60Hz
350
207
250
21.6
17.9
2.20
1.82
145
175
30.8
25.5
3.14
2.60
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
37.0
46.2
61.7
77.1
92.5
123
154
185
30.7
38.3
51.1
63.9
76.6
102
128
153
3.77
4.72
6.29
7.86
9.43
12.6
15.7
18.9
3.13
3.91
5.21
6.51
7.81
10.4
13.0
15.6
Allowable Pro
SF
N
2.80
1.45
2.80
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
1.45
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
08 — 1310 — 5
1
08 — 1320 — 5
2
08 — 1310 — 7
1
08 — 1320 — 7
2
08 — 1310 — 10
1
08 — 1320 — 10
2
08 — 1320 — 12
08 — 1320 — 15
08 — 1320 — 20
2
08 — 1320 — 25
08 — 1320 — 30
08 — 1420 — 40
08 — 1420 — 50
3
08 — 1420 — 60
kgf
50Hz
1470
60Hz
1370
50Hz
150
60Hz
140
1670
1570
170
160
1810
1720
185
175
1910
2060
2260
2350
2450
3970
4170
4310
1810
1960
2160
2260
2350
3820
4020
4170
195
210
230
240
250
405
425
440
185
200
220
230
240
390
410
425
1450r/min
1750r/min
kW
Hollow Shaft
Output speed n2
r/min
50Hz
60Hz
3-phase
RNYM Series Hollow Shaft Type
Motor
Speed n1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM08–1310–5~10
Mass 12kg
(RNYM08–1310–B–5~10)
(Mass 14kg)
390 (433)
5
56
113
8
56
44
46
30H8
110
4- 11
A-A
A
44
44
138
46
2
112
92
9
RNYM08–1320–5~30
(RNYM08–1320–B–5~30)
Fig. 2
Mass 13kg
(Mass 16kg)
423 (466)
112
46
58
5
119
30.6
22
A
27.5
58
46
62
74
132
33.3
5
1.
R
46
46
8
31.4
85h7
85h7
1.35
30H8
110
4-
A-A
11
138
46
86.5
5
A
46
62
130
9
92
34
9
RNYM08–1420–40~60
(RNYM08–1420–B–40~60)
Fig. 3
155 ( 155)
9
155( 155)
1.
R
17
5
31.4
85h7
85h7
A
30.6
22
1.35
76
56
44
116
46
46
112
5
33.3
Fig. 1
Mass 17kg
(Mass 19kg)
474 (517)
A
10
52
35H8
A
A-A
4- 14
118
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
138
138
20
52
155 ( 155)
70
57
R1
88
75
.5
37
95h7
95h7
1.75
93
26
10
146
70
5
158
59
38.3
59
35.6
5
57
75
155
43
3. Dimentions and Masses in the drawings are subject to change
without notice.
39
0.55
kW
0.55kW 3-phase Motor
3-phase Motor Indoor Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
247
204
25.1
20.8
308
255
31.4
26.0
370
307
37.7
31.3
462
383
47.2
39.1
617
511
62.9
52.1
732
613
74.6
62.5
870
721
88.8
73.5
1040
870
107
88.3
1390
1150
142
118
1480
1440
151
147
1480
1480
151
151
1480
1480
151
151
1480
1480
151
151
1480
1480
151
151
Output speed n2
r/min
50Hz
18.1
14.5
12.1
9.67
7.25
6.04
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
Motor
Speed n1
60Hz
21.9
17.5
14.6
11.7
8.75
7.29
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
N
SF
50Hz
6230
6230
6230
6230
6230
6230
9810
9810
9810
9810
9810
9810
9810
9810
1.45
1.45
1.45
1.45
1.19
✻
1.45
1.42
1.06
✻
✻
✻
✻
✻
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Allowable Pro
kgf
60Hz
50Hz
6130
635
6230
635
6230
635
6230
635
6230
635
6230
635
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
60Hz
625
635
635
635
635
635
1000
1000
1000
1000
1000
1000
1000
1000
08
08
08
08
08
08
08
08
08
08
08
08
08
08
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1530
1530
1530
1530
1530
1530
1640
1640
1640
1640
1640
1640
1640
1640
—
—
—
—
—
—
—
—
—
—
—
—
—
—
80
100
120
150
200
240
300
360
480
600
720
900
1200
1440
4
5
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM08–1530–80~240
Mass 24kg
(RNYM08–1530–B–80~240)
(Mass 26kg)
Fig. 4
498 (541)
68
68
84
5
157
96
5
136
4- 18
10
RNYM08–1640–300~1440
(RNYM08–1640–B–300~1440)
Fig. 5
12
93
93
155 ( 155)
A
156
A-A
10
138
45H8
67
17
213
129
109
5
1.
R
67
48.8
84
64
14
47.5
110h7
110h7
1.95
45.6
A
30
64
109
213
9.5
Mass 68kg
(Mass 70kg)
12
604
116
160
155
85
A
224
138
280
17
55H8
145
85
170
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
113
A
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
40
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.75kW 3-phase Motor
0.75
RNYM Series Hollow Shaft Type
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
21.0
17.4
2.14
1.78
50Hz
290
60Hz
350
207
250
29.4
24.4
3.00
2.49
145
175
42.0
34.8
4.29
3.55
N
SF
60Hz
1370
1370
2060
1570
1570
2300
1720
1720
2600
50Hz
150
150
220
170
170
250
185
185
280
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
1470
1470
2160
1670
1670
2450
1810
1810
2750
2.05
1.07
2.05
2.05
1.07
2.05
1.07
1.07
2.05
50Hz
60Hz
60Hz
140
140
210
160
160
235
175
175
265
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
1310
1320
1420
1310
1320
1420
1310
1320
1420
—
—
—
—
—
—
—
—
—
5
5
5
7
7
7
10
10
10
1
2
3
1
2
3
1
2
3
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Hollow Shaft
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1–1310–5~10
Mass 13kg
(RNYM1–1310–B–5~10)
(Mass 16kg)
390 (433)
5
56
113
8
56
44
46
30H8
110
4- 11
A-A
A
44
44
138
46
2
112
92
9
RNYM1–1320–5~10
(RNYM1–1320–B–5~10)
Fig. 2
Mass 15kg
(Mass 17kg)
112
423 (466)
46
5
58
119
30.6
22
A
27.5
58
46
62
74
132
33.3
5
1.
R
46
46
8
31.4
85h7
85h7
1.35
30H8
110
4- 11
A-A
138
46
86.5
5
A
46
62
130
9
92
34
9
RNYM1–1420–5~10
(RNYM1–1420–B–5~10)
Fig. 3
155 ( 155)
9
155( 155)
1.
R
17
5
31.4
85h7
85h7
1.35
76
A
30.6
22
56
44
116
46
46
112
5
33.3
Fig. 1
Mass 18kg
(Mass 20kg)
474 (517)
70
5
A
10
52
35H8
A
A-A
4- 14
10
118
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
138
138
20
52
155 ( 155)
70
57
R1
88
75
.5
37
95h7
95h7
1.75
146
93
26
158
59
38.3
59
35.6
5
57
75
155
43
3. Dimentions and Masses in the drawings are subject to change
without notice.
41
0.75
kW
0.75kW 3-phase Motor
3-phase Motor Indoor Type
96.7
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
50.4
41.8
5.14
4.26
Output speed n2
r/min
50Hz
121
Motor
Speed n1
60Hz
146
117
63.1
52.2
6.43
5.33
84.1
69.7
8.57
7.10
72.5
87.5
58.0
70.0
105
48.3
58.3
126
104
12.9
10.7
36.3
43.8
168
139
17.1
14.2
29.0
35.0
210
174
21.4
17.8
24.2
29.2
252
209
25.7
21.3
87.1
10.7
N
SF
50Hz
1910
2840
2060
3090
2260
3330
2350
3530
2450
3730
3970
5740
4170
6030
4310
6230
1.07
2.05
1.07
2.05
1.07
2.05
1.07
2.05
1.07
2.05
1.07
2.05
1.07
2.05
1.07
2.05
8.88
50Hz
195
290
210
315
230
340
240
360
250
380
405
585
425
615
440
635
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
1 — 1320 — 12
4
5
1 — 1420 — 12
4
1 — 1320 — 15
5
1 — 1420 — 15
4
1 — 1320 — 20
5
1 — 1420 — 20
4
1 — 1320 — 25
5
1 — 1420 — 25
4
1 — 1320 — 30
5
1 — 1420 — 30
5
1 — 1420 — 40
6
1 — 1520 — 40
5
1 — 1420 — 50
6
1 — 1520 — 50
5
1 — 1420 — 60
6
1 — 1520 — 60
kgf
60Hz
1810
2750
1960
2940
2160
3190
2260
3380
2350
3580
3820
5540
4020
5830
4170
6030
50Hz
60Hz
60Hz
185
280
200
300
220
325
230
345
240
365
390
565
410
595
425
615
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1–1320–12~30
Mass 15kg
(RNYM1–1320–B–12~30)
(Mass 17kg)
112
423 (466)
46
5
58
119
30.6
22
A
27.5
58
46
62
74
132
33.3
5
1.
R
46
46
8
31.4
85h7
85h7
1.35
30H8
110
4- 11
A-A
138
46
86.5
5
A
46
62
130
9
92
34
9
RNYM1–1420–12~60
(RNYM1–1420–B–12~60)
Fig. 5
155 ( 155)
Fig. 4
Mass 18kg
(Mass 20kg)
474 (517)
A
10
20
52
A
A-A
4- 14
118
75
155
10
RNYM1–1520–40~60
(RNYM1–1520–B–40~60)
Fig. 6
57
43
Mass 26kg
(Mass 28kg)
498 (541)
150
68
68
84
5
A
45.6
30
28
45H8
94
80
67
178
1.
5
R
67
48.8
84
70
14
47.5
110h7
1.95
110h7
178
113
5
4- 14
A
70
80
175
10
42
136
138
156
A-A
155 ( 155)
10
138
35H8
138
155 ( 155)
70
57
52
88
75
R1
158
.5
37
95h7
1.75
93
26
95h7
146
70
5
59
38.3
59
35.6
5
68
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.75kW 3-phase Motor
0.75
RNYM Series Hollow Shaft Type
50Hz
18.1
60Hz
21.9
14.5
12.1
17.5
14.6
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
336
279
34.3
28.4
420
504
348
418
42.9
51.4
Allowable Pro
N
SF
50Hz
6230
6230
6230
6230
1.07
2.05
1.07
1.07
35.5
42.6
50Hz
635
635
635
635
1450r/min
1750r/min
60Hz
625
625
635
635
1
1
1
1
—
—
—
—
1530
1531
1530
1530
— 80
— 80
— 100
— 120
1
2
1
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
6130
6130
6230
6230
50Hz
60Hz
Hollow Shaft
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1–1530–80~240
Mass 25kg
(RNYM1–1530–B–80~240)
(Mass 28kg)
Fig. 1
498 (541)
68
84
5
157
A
45.6
30
45H8
67
A
156
A-A
10
136
4- 18
10
RNYM1–1531–80
(RNYM1–1531–B–80)
Fig. 2
138
213
129
109
48.8
5
1.
R
67
17
84
64
14
47.5
110h7
110h7
1.95
155 ( 155)
68
96
5
64
109
213
9.5
Mass 26kg
(Mass 28kg)
498 (541)
84
5
45H8
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
4- 18
155 ( 155)
113
A
156
A-A
136
138
67
129
109
5
1.
R
67
17
84
64
14
47.5
110h7
110h7
1.95
10
157
A
30
213
68
48.8
68
45.6
5
64
109
213
9.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
43
0.75
0.75kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
631
522
64.3
53.3
Output speed n2
r/min
50Hz
9.67
60Hz
11.7
7.25
8.75
6.04
7.29
4.83
4.03
3.02
2.42
2.01
1.61
1.21
1.01
5.83
4.86
3.65
2.92
2.43
1.94
1.46
1.22
Motor
Speed n1
732
841
732
1010
1190
1420
1480
1480
1480
1480
1480
1480
697
697
732
836
983
1180
1480
1480
1480
1480
1480
1480
74.6
85.7
74.6
103
121
145
151
151
151
151
151
151
Allowable Pro
N
SF
50Hz
6230
9810
6230
9810
6230
9810
9810
9810
9810
9810
9810
9810
9810
9810
1.07
2.35
✻
1.76
✻
1.47
1.07
1.04
✻
✻
✻
✻
✻
✻
71.0
71.0
74.6
85.2
100
120
151
151
151
151
151
151
50Hz
635
1000
635
1000
635
1000
1000
1000
1000
1000
1000
1000
1000
1000
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
6230
9810
6230
9810
6230
9810
9810
9810
9810
9810
9810
9810
9810
9810
50Hz
60Hz
60Hz
635
1000
635
1000
635
1000
1000
1000
1000
1000
1000
1000
1000
1000
1
1
1
1
1
1
1
1
1
1
1
1
1
1
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1530
1631
1530
1631
1530
1631
1640
1640
1640
1640
1640
1640
1640
1640
—
—
—
—
—
—
—
—
—
—
—
—
—
—
150
150
200
200
240
240
300
360
480
600
720
900
1200
1440
1
2
1
2
1
2
3
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1–1530–150~240
Mass 25kg
(RNYM1–1530–B–150~240)
(Mass 28kg)
Fig. 1
498 (541)
68
68
84
5
157
96
5
136
4- 18
10
RNYM1–1631–150~240
(RNYM1–1631–B–150~240)
Fig. 2
12
93
93
155 ( 155)
A
156
A-A
10
138
45H8
67
17
213
129
109
5
1.
R
67
48.8
84
64
14
47.5
110h7
110h7
1.95
45.6
A
30
64
109
213
9.5
Mass 46kg
(Mass 48kg)
12
558
113
A
160
164
85
138
27
55H8
145
85
170
85
280
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
155
55.6
40
A
224
A-A
19
186
19
4- 22
85
145
110
170
280
RNYM1–1640–300~1440
(RNYM1–1640–B–300~1440)
Fig. 3
12
93
93
Mass 68kg
(Mass 70kg)
12
604
116
160
155
85
A
224
138
280
17
55H8
145
85
170
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
113
A
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
44
3. Dimentions and Masses in the drawings are subject to change
without notice.
1.1kW 3-phase Motor
1.1
RNYM Series Hollow Shaft Type
60Hz
350
207
250
43.2
35.8
4.40
3.65
145
175
61.7
51.1
6.29
5.21
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
74.0
92.5
123
154
185
247
308
370
61.3
76.6
102
128
153
204
255
307
7.54
9.43
12.6
15.7
18.9
25.1
31.4
37.7
6.25
7.81
10.4
13.0
15.6
20.8
26.0
31.3
N
SF
2.00
1.40
2.00
1.40
1.40
1.40
1.40
1.40
1.40
1.40
1.40
1.40
1.40
1.40
60Hz
2060
50Hz
220
60Hz
210
2450
2300
250
235
2750
2600
280
265
2840
3090
3330
3530
3730
5740
6030
6230
2750
2940
3190
3380
3580
5540
5830
6030
290
315
340
360
380
585
615
635
280
300
325
345
365
565
595
615
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
2160
1450r/min
1750r/min
1H
1H
1H
1H
1H
1H
1H
1H
1H
1H
1H
1H
1H
1H
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1410
1420
1410
1420
1410
1420
1420
1420
1420
1420
1420
1520
1520
1520
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
5
7
7
10
10
12
15
20
25
30
40
50
60
1
2
1
2
1
2
Hollow Shaft
50Hz
290
Allowable Pro
50Hz
60Hz
2
3
3-phase
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
30.8
25.5
3.14
2.60
Output speed n2
r/min
Motor
Speed n1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1H–1410–5~10
Mass 20kg
(RNYM1H–1410–B–5~10)
(Mass 24kg)
5
59
150
59
428 (490)
5
66
90
.5
R1
22
132
A
52
35H8
138
55
4- 11
118
4
10
RNYM1H–1420–5~30
(RNYM1H–1420–B–5~30)
Fig. 2
55
132
A-A
143
52
66
55
38.3
37
95h7
95h7
66
55
35.6
10
1.75
10
118
A
26
167( 167)
Fig. 1
Mass 21kg
(Mass 25kg)
504 (566)
5
70
A
10
.5
R1
52
52
A
A-A
4- 14
118
68
150
68
Mass 29kg
(Mass 33kg)
534 (596)
84
5
45.6
28
45H8
94
80
67
178
1.
5
R
67
48.8
84
70
14
47.5
110h7
178
A
30
1.95
110h7
43
4- 14
A
70
80
175
10
136
143
156
A-A
167 ( 167)
5
75
155
10
RNYM1H–1520–40~60
(RNYM1H–1520–B–40~60)
Fig. 3
57
119
10
143
35H8
138
167 ( 167)
98
37
95h7
95h7
1.75
20
26
146
158
88
70
75
57
59
38.3
59
35.6
5
68
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
45
1.1
1.1kW 3-phase Motor
kW
3-phase Motor Indoor Type
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
493
409
50.3
41.7
617
511
62.9
52.1
740
613
75.4
62.5
925
766
94.3
78.1
1230
1020
126
104
1480
1230
151
125
Output speed n2
r/min
50Hz
18.1
14.5
12.1
9.67
7.25
6.04
Motor
Speed n1
60Hz
21.9
17.5
14.6
11.7
8.75
7.29
N
SF
1.40
2.00
2.00
1.60
1.20
1.00
kgf
50Hz
6230
9810
9810
9810
9810
9810
60Hz
6130
9810
9810
9810
9810
9810
50Hz
635
1000
1000
1000
1000
1000
60Hz
625
1000
1000
1000
1000
1000
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
1H
1H
1H
1H
1H
1H
—
—
—
—
—
—
1531
1630
1630
1631
1631
1631
—
—
—
—
—
—
80
100
120
150
200
240
4
5
6
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1H–1531–80
Mass 29kg
(RNYM1H–1531–B–80)
(Mass 33kg)
Fig. 4
528 (590)
84
5
A
156
A-A
4- 18
136
12
93
93
64
10
RNYM1H–1630–100~120
(RNYM1H–1630–B–100~120)
Fig. 5
143
45H8
67
17
1.
5
R
67
167 ( 167)
84
64
14
47.5
110h7
110h7
1.95
119
A
30
10
157
213
129
109
68
48.8
68
45.6
5
109
213
9.5
Mass 52kg
(Mass 56kg)
12
593
A
55.6
160
167
164
85
143
27
55H8
145
85
170
85
280
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
118
40
A
224
A-A
19
186
4- 22
19
85
145
110
170
280
RNYM1H–1631–150~240
(RNYM1H–1631–B–150~240)
Fig. 6
12
93
93
Mass 53kg
(Mass 57kg)
12
605
118
A
160
143
27
A
224
167
164
85
145
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
46
3. Dimentions and Masses in the drawings are subject to change
without notice.
1.5kW 3-phase Motor
1.5
RNYM Series Hollow Shaft Type
50Hz
290
60Hz
350
207
250
58.9
48.8
6.00
4.97
145
175
84.1
69.7
8.57
7.10
Allowable Pro
N
SF
1.47
1.03
1.47
1.47
1.03
1.47
1.03
1.03
1.47
50Hz
2160
2160
3140
2450
2450
3530
2750
2750
3920
50Hz
220
220
320
250
250
360
280
280
400
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
2060
2060
2940
2300
2300
3330
2600
2600
3730
50Hz
60Hz
60Hz
210
210
300
235
235
340
265
265
380
2
2
2
2
2
2
2
2
2
—
—
—
—
—
—
—
—
—
1410
1420
1520
1410
1420
1520
1410
1420
1520
—
—
—
—
—
—
—
—
—
5
5
5
7
7
7
10
10
10
1
2
3
1
2
3
1
2
3
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Hollow Shaft
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
42.0
34.8
4.29
3.55
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM2–1410–5~10
Mass 22kg
(RNYM2–1410–B–5~10)
(Mass 26kg)
5
59
150
59
428 (490)
5
66
90
132
A
52
35H8
138
55
4- 11
4
10
RNYM2–1420–5~10
(RNYM2–1420–B–5~10)
Fig. 2
55
132
A-A
118
143
52
22
66
55
.5
R1
66
55
38.3
37
95h7
95h7
35.6
10
1.75
10
118
A
26
167( 167)
Fig. 1
Mass 22kg
(Mass 26kg)
504 (566)
5
70
52
A
A-A
4- 14
118
12
93
93
57
75
155
10
RNYM2–60–80~120
(RNYM2–60–B–80~120)
Fig. 3
143
35H8
138
10
167 ( 167)
98
.5
R1
52
A
10
37
95h7
95h7
1.75
20
26
146
158
88
70
75
57
59
38.3
59
35.6
5
43
Mass 85kg
(Mass 90kg)
593 (655)
12
164
32
186
143
A
55H8
A-A
19
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
4- 22
85
110
167 ( 167)
27
110
85
280
170
145
85
224
19
59.3
.5
R2
85
160
A
16
58
150h7
150h7
2.2
55.6
40
145
170
280
3. Dimentions and Masses in the drawings are subject to change
without notice.
47
1.5
1.5kW 3-phase Motor
kW
3-phase Motor Indoor Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
101
83.6
10.3
8.52
Output speed n2
r/min
50Hz
121
96.7
Motor
Speed n1
60Hz
146
117
126
104
12.9
10.7
72.5
87.5
168
139
17.1
14.2
58.0
70.0
210
174
21.4
17.8
48.3
58.3
252
209
25.7
21.3
Allowable Pro
SF
N
50Hz
2840
4120
3090
4410
3330
4810
3530
5100
3730
5340
1.03
1.47
1.03
1.47
1.03
1.47
1.03
1.47
1.03
1.47
50Hz
290
420
315
450
340
490
360
520
380
545
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
2750
3970
2940
4220
3190
4610
3380
4900
3580
5150
50Hz
60Hz
60Hz
280
405
300
430
325
470
345
500
365
525
2
2
2
2
2
2
2
2
2
2
—
—
—
—
—
—
—
—
—
—
1420
1520
1420
1520
1420
1520
1420
1520
1420
1520
—
—
—
—
—
—
—
—
—
—
12
12
15
15
20
20
25
25
30
30
4
5
4
5
4
5
4
5
4
5
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM2–1420–12~30
Mass 22kg
(RNYM2–1420–B–12~30)
(Mass 26kg)
Fig. 4
504 (566)
5
A
10
.5
R1
52
52
A
A-A
4- 14
118
68
150
68
Mass 31kg
(Mass 35kg)
534 (596)
84
5
45.6
28
45H8
94
80
67
178
5
R
1.
67
48.8
84
70
14
47.5
110h7
178
A
30
1.95
110h7
43
4- 14
A
70
80
175
10
136
68
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
48
143
156
A-A
167 ( 167)
5
75
155
10
RNYM2–1520–12~30
(RNYM2–1520–B–12~30)
Fig. 5
57
119
10
143
35H8
138
167 ( 167)
98
37
95h7
1.75
20
26
95h7
146
70
158
88
70
75
57
59
38.3
59
35.6
5
3. Dimentions and Masses in the drawings are subject to change
without notice.
1.5kW 3-phase Motor
1.5
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
336
279
34.3
28.4
Output speed n2
r/min
50Hz
36.3
60Hz
43.8
29.0
35.0
420
348
42.9
35.5
24.2
29.2
504
418
51.4
42.6
Allowable Pro
N
SF
60Hz
5540
5540
5830
5830
6030
6030
50Hz
5740
5740
6030
6030
6230
6230
1.03
1.47
1.03
1.47
1.03
1.47
kgf
50Hz
585
585
615
615
635
635
60Hz
565
565
595
595
615
615
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
2 — 1520 — 40
1
2 — 1531 — 40
2
2 — 1520 — 50
1
2 — 1531 — 50
2
2 — 1520 — 60
1
2 — 1531 — 60
2
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kW
Hollow Shaft
RNYM Series Hollow Shaft Type
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM2–1520–40~60
Mass 31kg
(RNYM2–1520–B–40~60)
(Mass 35kg)
534 (596)
84
5
45.6
30
84
70
14
45H8
67
178
28
67
94
80
R
1.
48.8
5
47.5
110h7
1.95
110h7
178
A
167 ( 167)
150
68
68
5
119
Fig. 1
4- 14
A-A
143
156
A
70
80
175
10
136
RNYM2–1531–40~80
(RNYM2–1531–B–40~80)
Fig. 2
68
10
Mass 30kg
(Mass 34kg)
528 (590)
84
5
45H8
A
156
A-A
4- 18
136
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
143
67
17
5
1.
R
67
167 ( 167)
84
64
14
47.5
110h7
110h7
1.95
119
A
30
10
157
213
129
109
68
48.8
68
45.6
5
64
109
213
9.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
49
1.5
1.5kW 3-phase Motor
kW
3-phase Motor Indoor Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
673
557
68.6
56.8
Output speed n2
r/min
50Hz
18.1
60Hz
21.9
14.5
12.1
9.67
7.25
6.04
Motor
Speed n1
17.5
14.6
11.7
8.75
7.29
841
1010
1260
1480
1480
697
836
1040
1390
1480
85.7
103
129
151
151
Allowable Pro
SF
1.03
1.47
1.47
1.47
1.17
*
*
71.0
85.2
107
142
151
N
kgf
50Hz
6230
9810
9810
9810
9810
9810
9810
60Hz
6130
9660
9810
9810
9810
9810
9810
50Hz
635
1000
1000
1000
1000
1000
1000
60Hz
625
985
1000
1000
1000
1000
1000
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
2
2
2
2
2
2
2
—
—
—
—
—
—
—
1531
1630
1630
1630
1631
1631
1631
—
—
—
—
—
—
—
80
80
100
120
150
200
240
3
4
4
5
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM2–1531–80
Mass 30kg
(RNYM2–1531–B–80)
(Mass 34kg)
Fig. 3
528 (590)
84
5
A
156
A-A
4- 18
136
12
93
93
64
10
RNYM2–1630–80~120
(RNYM2–1630–B–80~120)
Fig. 4
143
45H8
67
17
5
1.
R
67
167 ( 167)
84
64
14
47.5
110h7
110h7
1.95
119
A
30
10
157
213
129
109
68
48.8
68
45.6
5
109
213
9.5
Mass 52kg
(Mass 56kg)
12
593
A
55.6
160
167
164
85
143
27
55H8
145
85
170
85
280
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
118
40
A
224
A-A
19
186
4- 22
19
85
145
110
170
280
RNYM2–1631–150~240
(RNYM2–1631–B–150~240)
Fig. 5
12
93
93
Mass 53kg
(Mass 57kg)
12
605
118
A
160
143
27
A
224
167
164
85
145
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
50
3. Dimentions and Masses in the drawings are subject to change
without notice.
2.2kW 3-phase Motor
2.2
RNYM Series Hollow Shaft Type
60Hz
350
207
250
145
175
123
102
12.6
10.4
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
148
185
247
308
370
493
617
740
123
153
204
255
307
409
511
613
15.1
18.9
25.1
31.4
37.7
50.3
62.9
75.4
12.5
15.6
20.8
26.0
31.3
41.7
52.1
62.5
86.3
71.5
8.80
N
SF
2.50
1.00
1.68
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
7.29
kgf
50Hz
3140
60Hz
2940
50Hz
320
60Hz
300
3530
3330
360
340
3920
3730
400
380
4120
4410
4810
5100
5340
5740
6030
6230
3970
4220
4610
4900
5150
5540
5830
6030
420
450
490
520
545
585
615
635
405
430
470
500
525
565
595
615
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
3
3
3
3
3
3
3
3
3
3
3
3
3
3
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1510
1520
1510
1520
1510
1520
1520
1520
1520
1520
1520
1531
1531
1531
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
5
7
7
10
10
12
15
20
25
30
40
50
60
1
2
1
2
1
2
Hollow Shaft
50Hz
290
Allowable Pro
50Hz
60Hz
2
3
3-phase
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
61.7
51.1
6.29
5.21
Output speed n2
r/min
Motor
Speed n1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM3–1510–5~10
Mass 29kg
(RNYM3–1510–B–5~10)
(Mass 35kg)
478 (541)
77
30
A
156
4- 11
A-A
A
65
65
154
10
RNYM3–1520–5~30
(RNYM3–1520–B–5~30)
Fig. 2
5
150
68
68
Mass 34kg
(Mass 39kg)
553 (616)
84
5
45.6
30
84
70
14
45H8
178
150
67
28
67
94
80
R
1.
48.8
5
47.5
110h7
1.95
110h7
178
A
180 ( 180)
136
3
124
10
156
4- 14
A-A
A
70
80
175
10
136
68
10
RNYM3–1531–40~60
(RNYM3–1531–B–40~60)
Fig. 3
180 ( 180)
45H8
67
27
5
1.
R
67
77
65
124
14
47.5
110h7
110h7
1.95
100
150
5
154
164
68
77
65
68
48.8
5
45.6
Fig. 1
Mass 34kg
(Mass 39kg)
548 (611)
84
5
45H8
A
156
A-A
136
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
150
67
17
5
1.
R
67
4- 18
180 ( 180)
84
64
14
47.5
110h7
110h7
1.95
124
A
30
10
157
213
129
109
68
48.8
68
45.6
5
64
109
213
9.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
51
2.2
2.2kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Motor
Speed n1
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
50Hz
60Hz
83.3
101
817
18.1
986
21.9
104
126
1020
14.5
17.5 1230
125
151
1230
12.1
14.6 1480
151
151
1480
9.67 11.7 1480
151
151
1480
7.25
8.75 1480
151
151
1480
6.04
7.29 1480
Allowable Pro
Output speed n2
r/min
N
SF
1.00
1.00
1.00
*
*
*
kgf
50Hz
9810
9810
9810
9810
9810
9810
60Hz
9660
9810
9810
9810
9810
9810
50Hz
1000
1000
1000
1000
1000
1000
60Hz
985
1000
1000
1000
1000
1000
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
3 — 1630 — 80
3 — 1630 — 100
4
3 — 1630 — 120
3 — 1631 — 150
3 — 1631 — 200
5
3 — 1631 — 240
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM3–1630–80~120
Mass 57kg
(RNYM3–1630–B–80~120)
(Mass 63kg)
Fig. 4
12
93
93
624
12
124
A
160
180
164
85
280
150
55H8
27
85
145
85
170
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A
224
A-A
19
186
19
85
4- 22
145
110
170
280
RNYM3–1631–150~240
(RNYM3–1631–B–150~240)
Fig. 5
12
93
93
Mass 57kg
(Mass 63kg)
624
12
124
A
160
150
27
A
224
180
164
85
145
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
52
3. Dimentions and Masses in the drawings are subject to change
without notice.
3.0kW 3-phase Motor
3.0
RNYM Series Hollow Shaft Type
207
250
118
145
175
168
139
17.1
14.2
121
146
202
167
20.6
17.0
117
252
209
25.7
21.3
96.7
97.5
12.0
9.95
72.5
87.5
336
279
34.3
28.4
58.0
70.0
420
348
42.9
35.5
N
SF
1.23
1.83
1.23
1.83
1.23
1.83
1.23
1.83
1.23
1.83
1.23
1.83
1.23
1.83
60Hz
2940
50Hz
320
60Hz
300
3530
3330
360
340
3920
3730
400
380
4120
3970
420
405
4410
4220
450
430
4810
7700
5100
8090
4610
7350
4900
7750
490
785
520
825
470
750
500
790
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
3140
1450r/min
1750r/min
4
4
4
4
4
4
4
4
4
4
4
4
4
4
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1521
1522
1521
1522
1521
1522
1521
1522
1521
1522
1521
1633
1521
1633
—
—
—
—
—
—
—
—
—
—
—
—
—
—
1
2
1
2
1
2
1
2
1
2
1
3
1
3
5
5
7
7
10
10
12
12
15
15
20
20
25
25
Hollow Shaft
60Hz
350
Allowable Pro
50Hz
60Hz
3-phase
50Hz
290
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
84.1
69.7
8.57
7.10
Output speed n2
r/min
Motor
Speed n1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM4–1521–5~25
Mass 47kg
Fig. 1
(RNYM4–1521–B–5~25)
(Mass 58kg)
68
612
5
84
178
84
28
178
70
67
80
45H8
156
167
67
94
R1
.5
48.8
14
47.5
110h7
110h7
30
1.95
150
45.6
A
A
A-A
4- 14
70
80
175
150
136
10
5
68
68
10
RNYM4–1522–5~15
(RNYM4–1522–B–5~15)
Fig. 2
222
68
144
5
68
Mass 47kg
(Mass 58kg)
612
5
84
178
166
A
A-A
4- 14
70
80
175
10
12
93
68
10
RNYM4–1633–20~25
(RNYM4–1633–B–20~25)
Fig. 3
222
28
45H8
156
150
136
144
70
178
80
67
84
67
94
R1
.5
48.8
14
47.5
110h7
110h7
30
1.95
150
45.6
A
93
Mass 67kg
(Mass68kg)
12
749
A
144
160
222
164
85
280
166
27
55H8
145
85
170
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A
224
A-A
4- 22
19
186
19
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
53
3.0
3.0kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
504
418
51.4
42.6
Output speed n2
r/min
50Hz
48.3
60Hz
58.3
36.3
43.8
673
557
68.6
56.8
29.0
24.2
35.0
29.2
841
1010
697
836
85.7
103
71.0
85.2
Motor
Speed n1
Allowable Pro
N
SF
1.23
1.83
1.23
1.83
1.23
1.23
60Hz
8090
50Hz
855
60Hz
825
8830
8480
900
865
9120
9410
8880
9170
930
960
905
935
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
8380
50Hz
60Hz
4
4
4
4
4
4
—
—
—
—
—
—
1632
1633
1632
1633
1632
1632
—
—
—
—
—
—
4
5
4
5
30
30
40
40
50
60
4
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM4–1632–30~60
Mass 66kg
(RNYM4–1632–B–30~60)
(Mass 77kg)
Fig. 4
12
93
93
12
677
144
A
55.6
40
160
222
164
85
280
A
224
166
55H8
27
85
145
85
170
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
A-A
19
186
4- 22
19
85
145
110
170
280
RNYM4–1633–30~40
(RNYM4–1633–B–30~40)
Fig. 5
12
93
93
Mass 67kg
(Mass 78kg)
12
749
A
144
160
166
27
222
164
85
145
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A
224
A-A
4- 22
19
186
19
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
54
3. Dimentions and Masses in the drawings are subject to change
without notice.
3.7kW 3-phase Motor
3.7
RNYM Series Hollow Shaft Type
50Hz
290
60Hz
350
207
250
145
120
14.8
12.3
145
175
207
172
21.1
17.5
121
146
249
206
25.4
21.0
117
311
258
31.7
26.3
415
518
344
430
42.3
52.9
35.0
43.8
96.7
72.5
58.0
87.5
70.0
Allowable Pro
SF
1.00
1.49
1.00
1.49
1.00
1.49
1.00
1.49
1.00
1.49
1.00
1.00
N
kgf
50Hz
3140
60Hz
2940
50Hz
320
60Hz
300
3530
3330
360
340
3920
3730
400
380
4120
3970
420
405
4410
4220
450
430
4810
5100
4610
4900
490
520
470
500
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
5
5
5
5
5
5
5
5
5
5
5
5
—
—
—
—
—
—
—
—
—
—
—
—
1521
1522
1521
1522
1521
1522
1521
1522
1521
1522
1521
1521
—
—
—
—
—
—
—
—
—
—
—
—
5
5
7
7
10
10
12
12
15
15
20
25
1
2
1
2
1
2
1
2
1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Hollow Shaft
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
104
85.9
10.6
8.76
50Hz
60Hz
3-phase
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM5–1521–5~15
Mass 50kg
(RNYM5–1521–B–5~15)
(Mass 61kg)
68
68
612
5
84
178
84
70
28
178
80
67
94
R1
.5
48.8
14
45H8
156
167
47.5
110h7
110h7
67
150
45.6
A
30
1.95
A
A-A
4- 14
70
80
175
150
136
10
5
68
68
10
RNYM5–1522–5~15
(RNYM5–1522–B–5~15)
Fig. 2
222
5
144
Fig. 1
68
Mass 50kg
(Mass 61kg)
612
5
84
178
166
A
A-A
4- 14
70
80
175
10
RNYM5–1521–20~25
(RNYM5–1521–B–20~25)
5
68
68
Mass 50kg
(Mass 61kg)
612
5
84
178
70
80
28
178
84
45H8
A
A-A
4- 14
70
80
175
10
150
136
167
67
156
94
.5
R1
67
48.8
14
47.5
110h7
110h7
30
1.95
150
45.6
A
222
Fig. 3
68
144
10
222
28
45H8
156
150
136
144
70
178
80
67
84
67
94
R1
.5
48.8
14
47.5
110h7
110h7
30
1.95
150
45.6
A
68
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
55
3.7
3.7kW 3-phase Motor
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
415
344
42.3
35.0
518
430
52.9
43.8
622
516
63.4
52.6
Output speed n2
r/min
50Hz
72.5
58.0
48.3
60Hz
87.5
70.0
58.3
36.3
43.8
830
687
29.0
24.2
35.0
29.2
1040
1240
859
1030
84.6
Allowable Pro
SF
N
1.49
1.49
1.00
1.49
1.00
1.49
1.00
1.00
70.1
106
127
Motor
Speed n1
87.6
105
60Hz
7350
7750
8090
50Hz
785
825
855
60Hz
750
790
825
8830
8480
900
865
9120
9410
8880
9170
930
960
905
935
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
7700
8090
8380
50Hz
60Hz
5
5
5
5
5
5
5
5
—
—
—
—
—
—
—
—
1633
1633
1632
1633
1632
1633
1632
1632
—
—
—
—
—
—
—
—
20
25
30
30
40
40
50
60
4
5
4
5
4
5
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM5–1633–20~40
Mass 70kg
(RNYM5–1633–B–20~40)
(Mass 81kg)
Fig. 4
12
93
93
12
749
A
144
160
164
85
280
166
55H8
27
85
145
85
170
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
222
55.6
40
A
224
A-A
4- 22
19
186
85
19
145
110
170
280
RNYM5–1632–30~60
(RNYM5–1632–B–30~60)
Fig. 5
12
93
93
Mass 69kg
(Mass 80kg)
12
677
144
A
160
27
222
164
85
145
A
224
166
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
56
3. Dimentions and Masses in the drawings are subject to change
without notice.
5.5kW 3-phase Motor
5.5
RNYM Series Hollow Shaft Type
50Hz
290
207
145
121
96.7
72.5
58.0
48.3
36.3
60Hz
350
250
175
146
117
87.5
70.0
58.3
43.8
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
154
128
15.7
13.0
216
179
22.0
18.2
308
255
31.4
26.0
370
307
37.7
31.3
462
383
47.2
39.1
617
511
62.9
52.1
771
639
78.6
65.1
925
766
94.3
78.1
1230
1020
126
104
Allowable Pro
N
SF
60Hz
2940
3330
3730
3970
4220
7350
7750
8090
8480
50Hz
320
360
400
420
450
785
825
855
900
1450r/min
1750r/min
kW
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
50Hz
3140
3530
3920
4120
4410
7700
8090
8380
8830
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
50Hz
60Hz
60Hz
300
340
380
405
430
750
790
825
865
8
8
8
8
8
8
8
8
8
—
—
—
—
—
—
—
—
—
1522
1522
1522
1522
1522
1633
1633
1633
1633
—
—
—
—
—
—
—
—
—
5
7
10
12
15
20
25
30
40
1
2
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Hollow Shaft
Output speed n2
r/min
Motor
Speed n1
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM8–1522–5~15
Mass 57kg
(RNYM8–1522–B–5~15)
(Mass 68kg)
68
68
656
5
178
84
84
70
80
28
178
48.8
.5
R1
67
45H8
156
166
67
94
14
47.5
110h7
110h7
30
1.95
150
45.6
A
222
5
144
Fig. 1
A
A-A
4- 14
70
80
175
68
150
10
Fig. 2
12
136
10
RNYM8–1633–20~40
(RNYM8–1633–B–20~40)
93
93
Mass 77kg
(Mass 88kg)
12
793
144
160
222
164
85
280
A
166
55H8
27
85
224
145
85
170
R
2.
5
59.3
110
16
58
150h7
150h7
40
2.2
55.6
A
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
57
15
15W Single-phase Motor
W
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
290
350
193
233
145
175
121
146
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
7.25
8.75
6.04
7.29
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.371
0.307 0.038
0.031
0.556
0.461 0.057
0.047
0.742
0.615 0.076
0.063
0.890
0.738 0.091
0.075
1.11
0.922 0.113
0.094
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.23
1.84
0.227
0.188
2.97
2.46
0.303
0.251
3.71
3.07
0.378
0.313
4.45
3.69
0.454
0.376
5.93
4.92
0.605
0.501
7.42
6.15
0.756
0.627
8.90
7.38
0.908
0.752
11.9
9.83
1.21
1.00
14.8
12.3
1.51
1.25
17.8
14.8
1.82
1.50
Motor n1
Speed
Allowable Pro
SF
N
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
3.34
2.50
2.00
1.67
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1080
1080
1080
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1080
1080
1080
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
110
110
110
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
110
110
110
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
– 5
– 7.5
– 10
– 12
– 15
– 20
– 25
– 30
– 40
– 50
– 60
– 80
– 100
– 120
– 160
– 200
– 240
1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM0015–03–CA–5~240
Mass 2.6kg
Fig. 1
(RNYM0015–03–CA–B–5~240)
(Mass 3.2kg)
175 (214)
82
135 (174)
A
L=300
8
5
17.3
2
15.6
2
40
28
80)
23.1
A
15H8
94
76 (
28
15
80
R1
78
A-A
4- 5.5
80
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
58
3. Dimentions and Masses in the drawings are subject to change
without notice.
25W Single-phase Motor
25
RNYM Series Hollow Shaft Type
SF
N
kgf
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1080
1080
1080
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.00
1.50
1.20
1.00
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1080
1080
1080
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
110
110
110
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
110
110
110
1450r/min
1750r/min
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
03–
03 –
03 –
03 –
03 –
03 –
03 –
03 –
03 –
03 –
03 –
03–
03 –
03 –
03 –
03 –
03 –
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
– 5
– 7.5
– 10
– 12
– 15
– 20
– 25
– 30
– 40
– 50
– 60
– 80
– 100
– 120
– 160
– 200
– 240
Hollow Shaft
Allowable Pro
50Hz
60Hz
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM0025–03–CA–5~240
Mass 2.7kg
Fig. 2
(RNYM0025–03–CA–B–5~240)
(Mass 3.3kg)
Singlephase
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.618
0.512 0.063
0.052
0.927
0.768 0.095
0.078
1.24
1.02
0.126
0.104
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.47
2.05
0.252
0.209
3.09
2.56
0.315
0.261
3.71
3.07
0.378
0.313
4.95
4.10
0.504
0.418
6.18
5.12
0.630
0.522
7.42
6.15
0.756
0.627
9.89
8.20
1.01
0.836
12.4
10.2
1.26
1.04
14.8
12.3
1.51
1.25
19.8
16.4
2.02
1.67
24.7
20.5
2.52
2.09
29.7
24.6
3.03
2.51
Motor n1
Speed
175 (214)
82
135 (174)
A
L=300
8
5
17.3
2
15.6
2
40
28
80)
23.1
A
15H8
94
76 (
28
15
80
R1
78
A-A
4- 5.5
80
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
59
40
40W Single-phase Motor
W
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Motor n1
Speed
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.12
0.929 0.114
0.095
1.68
1.39
0.171
0.142
2.24
1.86
0.229
0.189
2.69
2.23
0.274
0.227
3.36
2.79
0.343
0.284
4.48
3.72
0.457
0.379
5.61
4.64
0.572
0.474
6.73
5.57
0.686
0.568
8.97
7.43
0.914
0.758
11.2
9.29
1.14
0.947
13.5
11.1
1.37
1.14
17.9
14.9
1.83
1.52
22.4
18.6
2.29
1.89
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
44.8
37.2
4.57
3.79
53.8
44.6
5.49
4.55
N
SF
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1420
1420
1420
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.20
1.00
1.60
1.20
1.00
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1420
1420
1420
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
145
145
145
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
07
07
07
07
07
07
07
07
07
07
07
07
07
07
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM004–07–CA–5~60
Mass 2.9kg
Fig. 1
(RNYM004–07–CA–B–5~60)
(Mass 3.5kg)
219
82
45
174
17.3
5
23.1
A
6
2
15.6
2
L=300
28
28
80
90
18
R1
104
A
15H8
78
A-A
4- 6.5
90
Mass 4.1kg
(Mass 4.5kg)
98
194 (253)
149 (208)
45
8
5
A
17.3
2
15.6
2
L=300
90
18
96)
R1
28
28
15H8
A
104
90 (
RNYM004–17–CA–150~240
(RNYM004–17–CA–B–150~240)
23.1
Fig. 2
94
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
60
4- 6.5
90
3. Dimentions and Masses in the drawings are subject to change
without notice.
40W Single-phase Motor
40
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
5.83
4.83
4.86
4.03
3.65
3.02
2.92
2.42
2.43
2.01
1.94
1.61
1.46
1.21
1.22
1.01
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
6.46
52.5
5.35
63.3
7.75
62.9
6.42
76.0
10.0
8.56
83.9
98.1
10.0
98.1
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
98.1
10.0
Allowable Pro
SF
N
kgf
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
1.55
1.29
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
60Hz
185
185
185
185
185
185
185
185
50Hz 1450r/min
60Hz 1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
004 –1240 – CA – 300
004 –1240 – CA – 360
004 –1240 – CA – 480
004 –1240 – CA – 600
3
004 –1240 – CA – 720
004 –1240 – CA – 900
004 –1240 – CA – 1200
004 –1240 – CA – 1440
W
Hollow Shaft
Motor n1
Speed
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Singlephase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Fig. 3
Designate model, voltage, and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM004–1240–CA–300~1440
Mass 6.9kg
(RNYM004–1240–CA–B–300~1440)
(Mass 7.3kg)
262
φ25.6
51
φ25H8
100
90
51
9
B
40
38
127
R
28.3
1.
5
φ26.2
38
65
8
1.35
76
22
211
A
A
A-A
4-φ9
40
65
127
Without brake
321
51
5
73
82
∼B
40
65
96
51
4-φ9
9
9
127
B
φ14
9
270
A
76
41
φ78h7
41
φ78h7
5
A
40
65
127
With brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
61
60
60W Single-phase Motor
W
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.68
1.39
0.171
0.142
2.52
2.09
0.257
0.213
3.36
2.79
0.343
0.284
4.04
3.34
0.412
0.341
5.04
4.18
0.514
0.426
6.73
5.57
0.686
0.568
8.41
6.97
0.857
0.710
10.1
8.36
1.03
0.852
13.5
11.1
1.37
1.14
16.8
13.9
1.71
1.42
20.2
16.7
2.06
1.70
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
Motor n1
Speed
Allowable Pro
SF
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.34
1.07
✻
✻
N
50Hz
637
686
785
834
883
981
1030
1080
1180
1270
1320
1420
1420
1420
1420
1420
1420
kgf
60Hz
588
637
735
785
834
932
981
1030
1130
1230
1270
1370
1420
1420
1420
1420
1420
50Hz
65
70
80
85
90
100
105
110
120
130
135
145
145
145
145
145
145
60Hz
60
65
75
80
85
95
100
105
115
125
130
140
145
145
145
145
145
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
Note : 1. Motor slippage may affect n1 and n2.
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
2. Allowable radial load shows the value when the distance from hollow
capacity.
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM006–17–CA–5~240
Mass 4.4kg
Fig. 1
(RNYM006–17–CA–B–5~240)
(Mass 4.8kg)
231 (271)
186 (226)
8
17.3
15.6
5
A
23.1
45
2
L=300
90
18
96)
R1
28
28
15H8
A
104
96 (
98
2
94
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
62
4- 6.5
90
3. Dimentions and Masses in the drawings are subject to change
without notice.
60W Single-phase Motor
60
Motor n1
Speed
RNYM Series Hollow Shaft Type
Allowable Pro
SF
N
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
1.03
✻
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
60Hz
185
185
185
185
185
185
185
185
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
006
006
006
006
006
006
006
006
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
CA
CA
CA
CA
CA
CA
CA
CA
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Singlephase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kgf
W
Hollow Shaft
Output speed n2
r/min
50Hz
60Hz
5.83
4.83
4.86
4.03
3.02
3.65
2.42
2.92
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
95.0
78.7
9.68
8.02
98.1
94.4
10.0
9.63
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
50Hz 1450r/min
60Hz 1750r/min
Fig. 2
Designate model, voltage, and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM006–1240–CA–300~1440
Mass 7.2kg
(RNYM006–1240–CA–B–300~1440)
(Mass 7.6kg)
280
229
φ25.6
51
φ25H8
100
90
51
9
B
40
38
127
R
28.3
1.
5
φ26.2
38
65
8
1.35
76
22
A
A
A-A
4-φ9
40
65
127
Without brake
339
5
41
41
51
5
288
73
9
82
40
65
96
51
4-φ9
9
127
B
76
φ78h7
φ14
φ78h7
A
A
40
65
127
9
∼B
With brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
63
90
90W Single-phase Motor
W
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Motor n1
Speed
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
2.09
2.52
0.257
0.213
3.13
3.78
0.386
0.320
4.18
5.04
0.514
0.426
5.02
6.05
0.617
0.511
6.27
7.57
0.772
0.639
8.36
10.1
1.03
0.852
10.4
12.6
1.29
1.07
15.1
12.5
1.54
1.28
20.2
16.7
2.06
1.70
25.2
20.9
2.57
2.13
30.3
25.1
3.09
2.56
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
50.2
5.50
5.11
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
N
SF
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
✻
✻
✻
✻
50Hz
637
686
785
834
883
981
1030
1080
1180
1270
1320
1420
1420
1420
1420
1420
1420
kgf
60Hz
588
637
735
785
834
932
981
1030
1130
1230
1270
1370
1420
1420
1420
1420
1420
50Hz
65
70
80
85
90
100
105
110
120
130
135
145
145
145
145
145
145
60Hz
60
65
75
80
85
95
100
105
115
125
130
140
145
145
145
145
145
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
Note : 1. Motor slippage may affect n1 and n2.
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
2. Allowable radial load shows the value when the distance from hollow
capacity.
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM009–17–CA–5~240
Mass 4.9kg
Fig. 1
(RNYM009–17–CA–B–5~240)
(Mass 5.3kg)
231 (271)
186 (226)
8
17.3
15.6
5
A
23.1
45
2
L=300
90
18
96)
R1
28
28
15H8
A
104
96 (
98
2
94
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
64
4- 6.5
90
3. Dimentions and Masses in the drawings are subject to change
without notice.
40W Single-phase Motor
90
40
RNYM Series Hollow Shaft Type
Allowable Pro
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
N
SF
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
✻
✻
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
60Hz
185
185
185
185
185
185
185
185
1450r/min
1750r/min
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
009
009
009
009
009
009
009
009
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
–1240 –
CA
CA
CA
CA
CA
CA
CA
CA
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Singlephase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kgf
50Hz
60Hz
Hollow Shaft
Output speed n2
r/min
50Hz
60Hz
5.83
4.83
4.86
4.03
3.02
3.65
2.42
2.92
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
Motor n1
Speed
Fig. 2
Designate model, voltage, and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM009–1240–CA–300~1440
Mass 7.7kg
(RNYM009–1240–CA–B–300~1440)
(Mass 8.1kg)
280
229
φ25.6
51
φ25H8
100
90
51
9
B
40
38
127
R
28.3
1.
5
φ26.2
38
65
8
1.35
76
22
A
A
A-A
4-φ9
40
65
127
Without brake
339
5
41
41
51
5
288
73
9
82
40
65
96
51
4-φ9
9
127
B
76
φ78h7
φ14
φ78h7
A
A
40
65
127
9
∼B
With brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
65
0.1
0.1kW Single-phase Motor
kW RNYM Series Hollow Shaft Type
Motor n1
Speed
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
2.80
0.286
2.32
0.237
Output speed n2
r/min
50Hz
60Hz
290
350
207
250
3.92
3.25
0.400
0.332
145
175
5.61
4.64
0.572
0.474
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
6.73
8.41
11.2
14.0
16.8
22.4
28.0
33.6
5.57
6.97
9.29
11.6
13.9
18.6
23.2
27.9
0.686
0.857
1.14
1.43
1.71
2.29
2.86
3.43
0.568
0.710
0.947
1.18
1.42
1.89
2.37
2.84
Allowable Pro
N
SF
4.00
2.00
4.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
kgf
50Hz
637
60Hz
588
50Hz
65
60Hz
60
686
637
70
65
785
735
80
75
834
883
981
1030
1080
1620
1720
1770
785
834
932
981
1030
1570
1670
1720
85
90
100
105
110
165
175
180
80
85
95
100
105
160
170
175
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
1
01 – 1110 – CB – 5
2
01 – 1120 – CB – 5
1
01 – 1110 – CB – 7
2
01 – 1120 – CB – 7
1
01 – 1110 – CB – 10
2
01 – 1120 – CB – 10
01 – 1120 – CB – 12
01 – 1120 – CB – 15
2
01 – 1120 – CB – 20
01 – 1120 – CB – 25
01 – 1120 – CB – 30
01 – 1220 – CB – 40
3
01 – 1220 – CB – 50
01 – 1220 – CB – 60
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1110–CB–5~10
Mass 6.0kg
(RNYM01–1110–CB–B–5~10)
(Mass 7.5kg)
275 (307)
6
37
20.6
16
22.8
1
R
30
74
37 37
29 29
6
21
52h7
52h7
1.15
20H8
30
50
A
A
29 29
74
4- 6.6
82
124 ( 124)
90
33
33
118
6
11
Fig. 1
2
A-A
8
66
Fig. 2
8
58
RNYM01–1120–CB–5~30
(RNYM01–1120–CB–B–5~30)
Mass 7.0kg
(Mass 8.5kg)
90
310 (342)
40
16
40
32
42
90
R
1
20H8
30
82
A
4- 6.6
32
A-A
118
30
A
6
21
52h7
52h7
1.15
82
20
6
50
33
22.8
33
20.6
6
42
88
8
66
116
72
Fig. 3
124 ( 124)
72
22
8
58
RNYM01–1220–CB–40~60
(RNYM01–1220–CB–B–40~60)
Mass 8.5kg
(Mass 10kg)
333 (365)
49
8
A
38
38
92
A-A
5
66
37
37
90
116
72
58
124 ( 124)
R
28.3
5
1.
26.2
78h7
25.6
1.35
96
25H8
A
4- 9
40
57
113
118
22
9
28
74
115
66
49
57
40
9
20
5
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.1kW Single-phase Motor
0.1
RNYM Series Hollow Shaft Type
N
SF
kgf
50Hz
3040
3090
3090
3090
3090
3090
6230
6230
6230
6230
6230
6230
6230
6230
2.00
2.00
2.00
2.00
1.74
1.45
4.00
3.85
2.89
2.31
1.93
1.54
1.16
✻
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
60Hz
2940
3040
3090
3090
3090
3090
6230
6230
6230
6230
6230
6230
6230
6230
50Hz
310
315
315
315
315
315
635
635
635
635
635
635
635
635
60Hz
300
310
315
315
315
315
635
635
635
635
635
635
635
635
1450r/min
1750r/min
kW
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
01
01
01
01
01
01
01
01
01
01
01
01
01
01
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1330
1330
1330
1330
1330
1330
1540
1540
1540
1540
1540
1540
1540
1540
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
– 80
– 100
– 120
– 150
– 200
– 240
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
4
Hollow Shaft
Output speed n2
r/min
50Hz
60Hz
21.9
18.1
17.5
14.5
14.6
12.1
9.67 11.7
8.75
7.25
7.29
6.04
5.83
4.83
4.86
4.03
3.65
3.02
2.92
2.42
2.43
2.01
1.94
1.61
1.46
1.21
1.22
1.01
Allowable Pro
50Hz
60Hz
5
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Singlephase
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
37.2
44.8
3.79
4.57
46.4
56.1
4.74
5.72
55.7
67.3
5.68
6.86
69.7
84.1
7.10
8.57
92.9
112
9.47
11.4
111
135
13.7
11.4
158
131
16.1
13.4
190
157
19.4
16.0
253
210
25.8
21.4
317
262
32.3
26.7
380
315
38.7
32.1
475
393
48.4
40.1
630
64.6
520
53.5
732
74.6
630
64.2
Motor n1
Speed
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1330–CB–80~240
Mass 10kg
(RNYM01–1330–CB–B–80~240)
(Mass 11kg)
Fig. 4
356 (388)
5
46
46
5
60
108
81
A
124 ( 124)
.5
92
79
R1
152
33.3
60
47
11
8
31.4
85h7
1.35
30.6
22
46
A
30H8
118
46
110
92
116
72
9
A-A
17.5
465（497）
197
84
φ45H8
118
67
156
14
84
5
1.
67
64
1.95
A
A-A
72
10
4-φ18
136
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
64
φ124（φ124）
112
A
14
R
φ47.5
φ110h7
30
109
5
129
68
φ110h7
3.5
Mass 24.5kg
(Mass 25.5kg)
213
68
79
58
φ45.6
5
47
152
RNYM01–1540–300~1440
(RNYM01–1540–B–300~1440)
Fig. 5
4- 11
48.8
9
109
213
54
3. Dimentions and Masses in the drawings are subject to change
without notice.
67
0.2
0.2kW Single-phase Motor
kW RNYM Series Hollow Shaft Type
Motor n1
Speed
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
5.61
4.64
0.572
0.474
Output speed n2
r/min
50Hz
60Hz
290
350
207
250
145
175
11.2
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
13.5
16.8
22.4
28.0
33.6
44.8
56.1
67.3
7.85
6.50
0.800
0.66
9.29
1.14
0.947
1.37
1.71
2.29
2.86
3.43
4.57
5.72
6.86
1.14
1.42
1.89
2.37
2.84
3.79
4.74
5.68
11.1
13.9
18.6
23.2
27.9
37.2
46.4
55.7
Allowable Pro
N
SF
4.00
2.00
4.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
kgf
50Hz
883
60Hz
834
50Hz
90
60Hz
85
981
932
100
95
1079
1030
110
105
1130
1230
1370
1470
1520
2650
2840
2940
1080
1180
1320
1370
1470
2550
2750
2840
115
125
140
150
155
270
290
300
110
120
135
140
150
260
280
290
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
02
02
02
02
02
02
02
02
02
02
02
02
02
02
– 1210
– 1220
– 1210
– 1220
– 1210
– 1220
– 1220
– 1220
– 1220
– 1220
– 1220
– 1320
– 1320
– 1320
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
5
7
7
10
10
12
15
20
25
30
40
50
60
1
2
1
2
1
2
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1210–CB–5~10
Mass 9.0kg
(RNYM02–1210–CB–B–5~10)
(Mass 10kg)
112
37
311 (343)
46
22
25.6
38
25H8
92
A
4- 9
A-A
9
74
Fig. 2
37
37
92
9
72
118
38
124 ( 124)
R
14
5
1.
46
37
A
26.2
78h7
78h7
1.35
61
8
92
5
46
37
37
5
28.3
Fig. 1
1.5
58
RNYM02–1220–CB–5~30
(RNYM02–1220–CB–B–5~30)
Mass 9.5kg
(Mass 11kg)
353 (385)
A
A-A
4- 9
40
57
113
RNYM02–1320–CB–40~60
(RNYM02–1320–CB–B–40~60)
Mass 11kg
(Mass 13kg)
112
46
46
381 (413)
5
58
30.6
22
A-A
27.5
58
46
62
46
110
132
74
33.3
1.
5
R
46
A
8
31.4
85h7
85h7
1.35
30H8
4- 11
A
46
72
68
62
130
116
92
9
119
124 ( 124)
5
20
5
118
Fig. 3
37
90
116
72
58
124 ( 124)
25H8
92
37
28
49
40
38
66
57
26.2
78h7
5
1.
R
38
5
96
A
25.6
1.35
78h7
49
8
118
22
9
115
74
28.3
9
34
9
58
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.2kW Single-phase Motor
0.2
RNYM Series Hollow Shaft Type
Allowable Pro
60Hz
4270
4360
4360
4360
4360
4360
6230
6230
6230
6230
6230
6230
6230
6230
50Hz
445
445
445
445
445
445
635
635
635
635
635
635
635
635
60Hz
435
445
445
445
445
445
635
635
635
635
635
635
635
635
02
02
02
02
02
02
02
02
02
02
02
02
02
02
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1430
1430
1430
1430
1430
1430
1540
1540
1540
1540
1540
1540
1540
1540
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
CB
– 80
– 100
– 120
– 150
– 200
– 240
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
4
5
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
kW
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
50Hz
4360
4360
4360
4360
4360
4360
6230
6230
6230
6230
6230
6230
6230
6230
2.00
2.00
2.00
2.00
1.74
1.45
2.00
1.93
1.44
1.16
✻
✻
✻
✻
1450r/min
1750r/min
Hollow Shaft
N
SF
50Hz
60Hz
Singlephase
Output speed n2
r/min
50Hz
60Hz
21.9
18.1
17.5
14.5
14.6
12.1
9.67 11.7
8.75
7.25
7.29
6.04
4.83
5.83
4.03
4.86
3.02
3.65
2.42
2.92
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
9.14
74.3
89.7
7.58
11.4
92.9
112
9.47
13.7
111
11.4
135
17.1
139
14.2
168
22.9
186
18.9
224
27.4
223
22.7
269
262
32.3
26.7
317
315
38.7
32.1
380
420
51.6
42.8
506
525
53.5
64.6
633
629
64.2
74.6
732
732
74.6
732
74.6
732
74.6
732
74.6
732
74.6
732
74.6
Motor n1
Speed
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1430–CB–80~240
(RNYM02–1430–CB–B–80~240)
Fig. 4
Mass 16kg
(Mass 17kg)
404 (436)
59
5
70
130
A
105
35.6
35H8
52
118
108
92
52
178
38.3
.5
R1
14
70
54
10
37
95h7
95h7
26
1.75
138
A-A
20
58
RNYM02–1540–CB–300~1440
(RNYM02–1540–CB–B–300~1440)
112
A
67
67
156
φ45H8
14
1.
5
1.95
84
14
R
φ47.5
φ110h7
30
φ110h7
485（517）
197
84
5
64
68
109
68
8
Mass 26kg
(Mass 27.5kg)
129
5
92
178
φ45.6
Fig. 5
54
213
72
A
4- 14
10
48.8
10
118
116
118
A
A-A
72
10
4-φ18
136
124 ( 124)
59
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
64
109
213
φ124（φ124）
5
54
3. Dimentions and Masses in the drawings are subject to change
without notice.
69
0.4
0.4kW Single-phase Motor
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.14
0.947
9.29
11.2
Output speed n2
r/min
50Hz
60Hz
350
290
207
250
15.7
13.0
1.60
1.33
145
175
22.4
18.6
2.29
1.89
121
96.7
72.5
58.0
48.3
36.3
29.0
24.2
146
117
87.5
70.0
58.3
43.8
35.0
29.2
26.9
33.6
44.8
56.1
67.3
89.7
112
135
22.3
27.9
37.2
46.4
55.7
74.3
92.9
111
2.74
3.43
4.57
5.72
6.86
9.14
11.4
13.7
2.27
2.84
3.79
4.74
5.68
7.58
9.47
11.4
Motor n1
Speed
Allowable Pro
N
SF
3.85
2.00
3.85
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
kgf
50Hz
1470
60Hz
1370
50Hz
150
60Hz
140
1670
1570
170
160
1810
1720
185
175
1910
2060
2260
2350
2450
3970
4170
4310
1810
1960
2160
2260
2350
3820
4020
4170
195
210
230
240
250
405
425
440
185
200
220
230
240
390
410
425
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
05 – 1310 – CB – 5
1
05 – 1320 – CB – 5
2
05 – 1310 – CB – 7
1
05 – 1320 – CB – 7
2
05 – 1310 – CB – 10
1
05 – 1320 – CB – 10
2
05 – 1320 – CB – 12
05 – 1320 – CB – 15
05 – 1320 – CB – 20
2
05 – 1320 – CB – 25
05 – 1320 – CB – 30
05 – 1420 – CB – 40
05 – 1420 – CB – 50
3
05 – 1420 – CB – 60
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1310–CB–5~10
Mass 13kg
(RNYM05–1310–CB–B–5~10)
(Mass 16kg)
390 (433)
5
76
56
A
30.6
22
17
33.3
R
1.
5
46
112
56
56
44
44
8
31.4
85h7
85h7
1.35
46
30H8
110
4- 11
44
A-A
69
2
54
92
9
RNYM05–1320–CB–5~30
(RNYM05–1320–CB–B–5~30)
Fig. 2
A
44
112
Mass 15kg
(Mass 17kg)
112
46
423 (466)
46
5
58
119
30.6
22
A
27.5
58
46
62
74
132
33.3
1.
5
R
46
46
8
31.4
85h7
85h7
1.35
85.5
5
30H8
110
4- 11
A-A
A
46
62
34
130
116
92
9
69
9
54
RNYM05–1420–CB–40~60
(RNYM05–1420–CB–B–40~60)
Fig. 3
155 ( 155)
9
155 ( 155)
116
46
128
46
128
5
113
Fig. 1
Mass 18kg
(Mass 20kg)
474 (517)
70
5
128
35H8
A
A-A
4- 14
10
69
75
43
10
54
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
70
57
155
109
118
155 ( 155)
20
52
138
93
70
57
.5
R1
52
A
10
37
95h7
95h7
1.75
158
26
146
88
75
59
38.3
59
35.6
5
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.4kW Single-phase Motor
0.4
Output speed n2
r/min
50Hz
60Hz
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
7.25
8.75
6.04
7.29
4.83
5.83
4.03
4.86
3.02
3.65
2.42
2.92
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
Allowable Pro
N
SF
50Hz
6230
6230
6230
6230
6230
6230
9810
9810
9810
9810
9810
9810
9810
9810
2.00
2.00
2.00
2.00
1.63
1.36
2.00
1.95
1.46
1.17
✻
✻
✻
✻
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
05 – 1530 – CB – 80
05 – 1530 – CB – 100
05 – 1530 – CB – 120
4
05 – 1530 – CB – 150
05 – 1530 – CB – 200
05 – 1530 – CB – 240
05 – 1640 – CB – 300
05 – 1640 – CB – 360
05 – 1640 – CB – 480
05 – 1640 – CB – 600
5
05 – 1640 – CB – 720
05 – 1640 – CB – 900
05 – 1640 – CB – 1200
05 – 1640 – CB – 1440
kgf
60Hz
6130
6230
6230
6230
6230
6230
9810
9810
9810
9810
9810
9810
9810
9810
50Hz
635
635
635
635
635
635
1000
1000
1000
1000
1000
1000
1000
1000
1450r/min
1750r/min
60Hz
625
635
635
635
635
635
1000
1000
1000
1000
1000
1000
1000
1000
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
kW
Hollow Shaft
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
15.2
179
149
18.3
22.9
18.9
186
224
27.4
22.7
269
223
34.3
28.4
336
279
45.7
37.9
448
372
45.5
55
538
446
64.6
53.5
630
525
77.5
64.2
760
630
103
85.6
1010
840
1050
129
107
1270
151
128
1260
1480
1480
151
151
1480
151
151
1480
1480
151
1480
151
1480
50Hz
60Hz
Singlephase
RNYM Series Hollow Shaft Type
Motor n1
Speed
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1530–CB–80~240
Mass 25kg
(RNYM05–1530–CB–B–80~240)
(Mass 28kg)
Fig. 4
498 (541)
5
84
A
109
136
10
12
93
93
4- 18
64
10
109
213
155 ( 155)
128
A
156
A-A
RNYM05–1640–CB–300~1440
(RNYM05–1640–CB–B–300~1440)
Fig. 5
45H8
67
17
5
1.
R
67
96
14
47.5
110h7
110h7
1.95
84
64
30
157
213
129
109
68
48.8
68
45.6
5
9.5
Mass 68kg
(Mass 70kg)
12
604
116
160
155
85
A
224
138
280
17
55H8
145
85
170
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
113
A
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
71
15
15W Single-phase Reversible Motor
W
RNYM Series Hollow Shaft Type
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
50Hz
60Hz
0.371
350
290
0.307
0.038
0.031
0.556
233
193
0.461
0.057
0.047
0.742
175
145
0.615
0.076
0.063
0.890
146
121
0.738
0.091
0.075
1.11
96.7 117
0.922
0.113
0.094
72.5
87.5
1.48
1.23
0.151
0.125
58.0
70.0
1.85
1.54
0.189
0.157
48.3
58.3
2.23
1.84
0.227
0.188
36.3
43.8
2.97
2.46
0.303
0.251
29.0
35.0
3.71
3.07
0.378
0.313
24.2
29.2
4.45
3.69
0.454
0.376
18.1
21.9
5.93
4.92
0.605
0.501
14.5
17.5
7.42
6.15
0.756
0.627
12.1
14.6
8.90
7.38
0.908
0.752
9.06 10.9 11.9
9.83
1.21
1.00
8.75 14.8
7.25
12.3
1.51
1.25
7.29 17.8
6.04
14.8
1.82
1.50
Motor n1
Speed
Allowable Pro
SF
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1080
1080
1080
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
4.00
3.34
2.50
2.00
1.67
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
110
110
110
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1080
1080
1080
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
110
110
110
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
– 5
– 7.5
– 10
– 12
– 15
– 20
– 25
– 30
– 40
– 50
– 60
– 80
– 100
– 120
– 160
– 200
– 240
1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
Fig. 1
RNYM0015–03–CC–5~240
Mass 2.6kg
175
82
135
A
L=300
8
5
17.3
2
15.6
2
40
28
28
A
15H8
76
23.1
15
80
R1
94
78
A-A
4- 5.5
80
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
72
3. Dimentions and Masses in the drawings are subject to change
without notice.
25W Single-phase Reversible Motor
25
RNYM Series Hollow Shaft Type
SF
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1080
1080
1080
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.00
1.50
1.20
1.00
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
110
110
110
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1080
1080
1080
1450r/min
1750r/min
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
110
110
110
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
03
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
Hollow Shaft
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
8.75
7.25
7.29
6.04
Allowable Pro
50Hz
60Hz
2
ote : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Singlephase
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.618
0.512 0.063
0.052
0.927
0.768 0.095
0.078
1.24
1.02
0.126
0.104
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.47
2.05
0.252
0.209
3.09
2.56
0.315
0.261
3.71
3.07
0.378
0.313
4.95
4.10
0.504
0.418
6.18
5.12
0.630
0.522
7.42
6.15
0.756
0.627
9.9
8.20
1.01
0.836
12.4
10.2
1.26
1.04
14.8
12.3
1.51
1.25
19.8
16.4
2.02
1.67
24.7
20.5
2.52
2.09
29.7
24.6
3.03
2.51
Motor n1
Speed
Designate model and voltage and frequency when ordering.
Fig. 2
RNYM0025–03–CC–5~240
Mass 2.7kg
175
82
135
A
L=300
8
5
17.3
2
15.6
2
40
28
28
A
15H8
76
23.1
15
80
R1
94
78
A-A
4- 5.5
80
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
73
40
40W Single-phase Reversible Motor
W
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.12
0.929 0.114
0.095
1.68
1.39
0.171
0.142
2.24
1.86
0.229
0.189
2.69
2.23
0.274
0.227
3.36
2.79
0.343
0.284
4.48
3.72
0.457
0.379
5.61
4.64
0.572
0.474
6.73
5.57
0.686
0.568
8.97
7.43
0.914
0.758
11.2
9.29
1.14
0.947
13.5
11.1
1.37
1.14
17.9
14.9
1.83
1.52
22.4
18.6
2.29
1.89
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
44.8
37.2
4.57
3.79
53.8
44.6
5.49
4.55
Motor n1
Speed
Allowable Pro
SF
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1080
1080
1080
1420
1420
1420
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.20
1.00
1.60
1.20
1.00
50Hz
55
60
65
70
75
80
85
90
100
110
110
110
110
110
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1080
1080
1080
1420
1420
1420
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
105
110
110
110
110
145
145
145
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
07
07
07
07
07
07
07
07
07
07
07
07
07
07
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
Fig. 1
RNYM004–07–CC–5~120
Mass 2.9kg
219
82
45
174
17.3
5
23.1
A
6
2
15.6
2
L=300
28
28
80
90
18
R1
104
A
15H8
78
A-A
4- 6.5
90
Fig. 2
RNYM004–17–CC–150~240
Mass 4.1kg
194
98
149
8
17.3
5
A
23.1
45
2
15.6
2
L=300
28
28
15H8
90
90
18
R1
A
104
94
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
74
4- 6.5
90
3. Dimentions and Masses in the drawings are subject to change
without notice.
40W Single-phase Reversible Motor
40
Motor n1
Speed
RNYM Series Hollow Shaft Type
Output speed n2
r/min
50Hz
60Hz
5.83
4.83
4.86
4.03
3.65
3.02
2.92
2.42
2.01
2.43
1.61
1.94
1.21
1.46
1.01
1.22
Allowable Pro
SF
N
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
50Hz
1810
1810
1810
1810
1810
1810
1810
1810
1.55
1.29
✻
✻
✻
✻
✻
✻
60Hz
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
185
185
185
185
185
185
185
185
W
60Hz
185
185
185
185
185
185
185
185
004–
004–
004–
004–
004–
004–
004–
004–
1240
1240
1240
1240
1240
1240
1240
1240
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
3
Hollow Shaft
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
63.3
52.5
6.46
5.35
76.0
62.9
7.75
6.42
98.1
83.9
10.0
8.56
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
50Hz 1450r/min
60Hz 1750r/min
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Singlephase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model, voltage, and frequency when ordering.
Fig. 3
Mass 6.9kg
RNYM004–1240–CC–300~1440
262
51
φ25H8
90
51
9
38
100
127
5
1.
R
38
40
8
1.35
φ26.2
φ78h7
φ78h7
22
211
A
65
5
76
41
28.3
41
φ25.6
5
A
9
73
82
φ14
A-A
9
4-φ9
40
65
127
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and masses in the drawings are subject to change
without notice.
75
60
60W Single-phase Reversible Motor
W
RNYM Series Hollow Shaft Type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.68
1.39
0.142
0.171
2.52
2.09
0.213
0.257
3.36
2.79
0.284
0.343
4.04
3.34
0.341
0.412
5.04
4.18
0.426
0.514
6.73
5.57
0.568
0.686
8.41
6.97
0.710
0.857
10.1
8.36
0.852
1.03
13.5
11.1
1.14
1.37
16.8
13.9
1.42
1.71
20.2
16.7
1.70
2.06
26.9
22.3
2.27
2.74
33.6
2.84
27.9
3.43
40.4
3.41
33.4
4.12
50.4
4.26
41.8
5.14
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
95.0
8.02
9.68
78.7
9.63
98.1
10.0
94.4
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
10.0
98.1
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
87.5
72.5
70.0
58.0
58.3
48.3
43.8
36.3
35.0
29.0
29.2
24.2
21.9
18.1
17.5
14.5
14.6
12.1
9.67 11.7
8.75
7.25
6.04
7.29
5.83
4.83
4.86
4.03
3.65
3.02
2.92
2.42
2.43
2.01
1.94
1.61
1.21
1.46
1.22
1.01
Motor n1
Speed
Allowable Pro
SF
N
60Hz
588
637
735
785
834
932
981
1030
1130
1230
1270
1370
1420
1420
1420
1420
1420
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
65
70
80
85
90
100
105
110
120
130
135
145
145
145
145
145
145
185
185
185
185
185
185
185
185
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
006 – 17 – CC – 5
006 – 17 – CC – 7.5
006 – 17 – CC – 10
006 – 17 – CC – 12
006 – 17 – CC – 15
006 – 17 – CC – 20
006 – 17 – CC – 25
006 – 17 – CC – 30
1
006 – 17 – CC – 40
006 – 17 – CC – 50
006 – 17 – CC – 60
006 – 17 – CC – 80
006 – 17 – CC – 100
006 – 17 – CC – 120
006 – 17 – CC – 150
006 – 17 – CC – 200
006 – 17 – CC – 240
006 –1240 – CC – 300
006 –1240 – CC – 360
006 –1240 – CC – 480
006 –1240 – CC – 600
2
006 –1240 – CC – 720
006 –1240 – CC – 900
006 –1240 – CC –1200
006 –1240 – CC –1440
kgf
50Hz
637
686
785
834
883
981
1030
1080
1180
1270
1320
1420
1420
1420
1420
1420
1420
1810
1810
1810
1810
1810
1810
1810
1810
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.34
1.07
✻
✻
1.03
✻
✻
✻
✻
✻
✻
✻
50Hz
60Hz
60Hz
60
65
75
80
85
95
100
105
115
125
130
140
145
145
145
145
145
185
185
185
185
185
185
185
185
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
Fig. 1
RNYM006–17–CC–5~240
Mass 4.4kg
231
98
186
A
17.3
5
8
15.6
2
23.1
45
2
L=300
28
28
96
90
18
R1
104
A
15H8
94
A-A
Fig. 2
4- 6.5
90
RNYM006–1240–CC–300~1440
Mass 7.2kg
280
φ25H8
90
51
9
38
100
40
1.
5
R
38
65
8
1.35
φ26.2
φ78h7
A
127
22
φ78h7
229
51
5
76
41
28.3
41
φ25.6
5
A
9
73
82
φ14
A-A
9
4-φ9
40
65
127
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
76
3. Dimentions and Masses in the drawings are subject to change
without notice.
90W Single-phase Reversible Motor
90
Output speed n2
r/min
50Hz
60Hz
290
350
193
233
145
175
121
146
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
5.83
4.83
4.86
4.03
3.65
3.02
2.92
2.42
2.43
2.01
1.94
1.61
1.46
1.21
1.22
1.01
Allowable Pro
SF
N
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
009 – 17 – CC – 5
009 – 17 – CC – 7.5
009 – 17 – CC – 10
009 – 17 – CC – 12
009 – 17 – CC – 15
009 – 17 – CC – 20
009 – 17 – CC – 25
009 – 17 – CC – 30
1
009 – 17 – CC – 40
009 – 17 – CC – 50
009 – 17 – CC – 60
009 – 17 – CC – 80
009 – 17 – CC – 100
009 – 17 – CC – 120
009 – 17 – CC – 150
009 – 17 – CC – 200
009 – 17 – CC – 240
009 – 1240–CC – 300
009 – 1240–CC – 360
009 – 1240–CC – 480
009 – 1240–CC – 600
2
009 – 1240–CC – 720
009 – 1240–CC – 900
009 – 1240–CC –1200
009 – 1240–CC –1440
kgf
50Hz
637
686
785
834
883
981
1030
1080
1180
1270
1320
1420
1420
1420
1420
1420
1420
1810
1810
1810
1810
1810
1810
1810
1810
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
✻
60Hz
588
637
735
785
834
932
981
1030
1130
1230
1270
1370
1420
1420
1420
1420
1420
1810
1810
1810
1810
1810
1810
1810
1810
50Hz
65
70
80
85
90
100
105
110
120
130
135
145
145
145
145
145
145
185
185
185
185
185
185
185
185
1450r/min
1750r/min
60Hz
60
65
75
80
85
95
100
105
115
125
130
140
145
145
145
145
145
185
185
185
185
185
185
185
185
W
Hollow Shaft
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.213
0.257
2.09
2.52
0.320
0.386
3.13
3.78
0.426
0.514
4.18
5.04
0.511
0.617
5.02
6.05
0.639
0.772
6.27
7.57
0.852
1.03
8.36
10.1
1.07
1.29
10.4
12.6
1.28
1.54
12.5
15.1
1.70
2.06
16.7
20.2
2.13
2.57
20.9
25.2
2.56
3.09
25.1
30.3
3.41
4.12
33.4
40.4
4.26
5.14
41.8
50.4
5.11
5.50
50.2
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
10.0
10.0
98.1
98.1
50Hz
60Hz
Singlephase
RNYM Series Hollow Shaft Type
Motor n1
Speed
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
Fig. 1
RNYM009–17–CC–5~240
Mass 4.9kg
231
98
186
A
17.3
5
8
15.6
2
23.1
45
2
L=300
28
28
96
90
18
R1
104
A
15H8
94
A-A
Fig. 2
4- 6.5
90
RNYM009–1240–CC–300~1440
Mass 7.7kg
280
φ25H8
90
51
9
38
100
127
5
1.
R
38
40
8
1.35
φ26.2
φ78h7
A
65
22
φ78h7
229
51
5
76
41
28.3
41
φ25.6
5
A
9
73
82
φ14
A-A
9
4-φ9
40
65
127
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
77
Light Dust Proof
RNYM Series Hollow Shaft Type
Dimension J, L and the shape of terminal box are as below.
Please refer to page 62–67 for other dimensions and selection table.
L
J
J
L
without brake, with brake
Fig. 2
Fig. 3
36
50
Motor Power
0.1kW
0.2kW
0.4kW
Model
RNYM01-1110-CB(-B)-5~10
RNYM01-1120-CB(-B)-5~30
RNYM01-1220-CB(-B)-40~60
RNYM01-1330-CB(-B)-80~240
RNYM01-1440-CB(-B)-300~1440
RNYM01-1540-CB(-B)-300~1440
RNYM02-1210-CB(-B)-5~10
RNYM02-1220-CB(-B)-5~30
RNYM02-1320-CB(-B)-40~60
RNYM02-1430-CB(-B)-80~240
RNYM02-1540-CB(-B)-300~1440
RNYM05-1310-CB(-B)-5~10
RNYM05-1320-CB(-B)-5~30
RNYM05-1420-CB(-B)-40~60
RNYM05-1530-CB(-B)-80~240
RNYM05-1640-CB(-B)-300~1440
U1
U2
Terminal box ( 0.4kW)
(A rectifier is built-in for motors with brake)
Fig.
L
J
Mass (kg)
2
6.0(7.5)
120
289(307)
2
8.0(9.5)
120
325(342)
2
8.5(11)
120
348(365)
3
11(12)
120
370(388)
3
16(17)
120
435(453)
3
25(26)
120
479(497)
2
9.0(10)
120
325(343)
2
10(12)
120
368(385)
2
12(14)
120
395(413)
3
17(18)
120
418(436)
3
26(27.5)
120
499(517)
2
13(16)
120
390(433)
2
16(18)
130
423(466)
2
19(21)
130
474(517)
3
26(29)
130
498(541)
3
68.5(70.5)
130
604(647)
Values in brakets ( ) are for motors with brake.
PF 1/2
75
V2 V1
Y X
35.5
66
78
Terminal box (0.1, 0.2kW)
(A rectifier is built-in for motors with brake)
78
93
Y
X
PF 1/2
V2 V1
116
36
33
U1
U2
73
109
50
129.5
91.5
63
Outdoor Type
0.1~0.4kW Single-phase Motor Outdoor Type Light Dust Proof
Singlephase
Hollow Shaft
79
Light Dust Proof
Outdoor Type
MEMO
0.1
0.1kW Motor for inverter
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
700 (120Hz)
350
35.0
2.32
0.237
Motor
Speed n1
SF
2.00
Allowable Pro
N
kgf
60Hz
60Hz
588
60
25.0
250
500 (120Hz)
3.25
0.332
2.00
637
65
17.5
175
350 (120Hz)
4.64
0.474
2.00
735
75
14.6
11.7
8.75
7.00
5.83
4.38
3.50
2.92
146
117
87.5
70.0
58.3
43.8
35.0
29.2
292 (120Hz)
234 (120Hz)
175 (120Hz)
140 (120Hz)
117 (120Hz)
87.6 (120Hz)
70.0 (120Hz)
58.4 (120Hz)
5.57
6.97
9.29
11.6
13.9
18.6
23.2
27.9
0.568
0.710
0.947
1.18
1.42
1.89
2.37
2.84
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
785
834
932
981
1030
1570
1670
1720
80
85
95
100
105
160
170
175
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
01
01
01
01
01
01
01
01
01
01
01
01
01
01
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1110
1120
1110
1120
1110
1120
1120
1120
1120
1120
1120
1220
1220
1220
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
5
7
7
10
10
12
15
20
25
30
40
50
60
60Hz
1750r/min
Outline
Drawing
Fig.
1
2
1
2
1
2
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1110–AV–5~10
(RNYM01–1110–AV–B–5~10)
Mass 6.0kg
(Mass 7.5kg)
275 (307)
90
37
16
A
11
37
29
1
R
30
29
6
21
30
A
82
4- 6.6
20H8
29
A-A
8
66
29
74
2
8
RNYM01–1120–AV–5~30
(RNYM01–1120–AV–B–5~30)
Fig. 2
Mass 7.0kg
(Mass 8.5kg)
90
6
128
52h7
52h7
1.15
50
74
6
37
33
22.8
33
20.6
6
124 ( 124)
Fig. 1
33
310 (342)
33
40
6
82
A
40
32
50
42
20
30
20H8
82
A
4- 6.6
A-A
32
128
30
90
R
1
22.8
6
21
52h7
52h7
1.15
42
88
8
Fig. 3
124 ( 124)
20.6
16
22
8
66
RNYM01–1220–AV–40~60
(RNYM01–1220–AV–B–40~60)
Mass 8.5kg
(Mass 10kg)
333 (365)
38
38
92
A-A
5
80
37
37
90
A
124 ( 124)
5
1.
R
96
25H8
128
25.6
8
26.2
78h7
1.35
78h7
49
22
28
9
115
66
49
57
40
74
28.3
9
A
4- 9
40
57
113
20
5
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.1kW Motor for inverter
0.1
6Hz
2.19
1.75
1.46
1.17
0.875
0.729
Output speed n2
r/min
60Hz Allowable max speed
43.8 (120Hz)
21.9
35.0 (120Hz)
17.5
29.2 (120Hz)
14.6
23.4 (120Hz)
11.7
8.75 17.5 (120Hz)
7.29 14.6 (120Hz)
Output Torque Tout
Nm
kgf m
60Hz
60Hz
3.79
37.2
4.74
46.4
5.68
55.7
7.10
69.7
9.47
92.9
111
11.4
Allowable Pro
N
kgf
60Hz
60Hz
300
2940
310
3040
315
3090
315
3090
315
3090
315
3090
SF
2.00
2.00
2.00
2.00
2.00
1.80
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
01
01
01
01
01
01
–
–
–
–
–
–
1330
1330
1330
1330
1330
1330
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
80
100
120
150
200
240
60Hz
1750r/min
kW
Outline
Drawing
Fig.
Hollow Shaft
RNYM Series Hollow Shaft Type
Motor
Speed n1
4
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Fig. 4
Motor for
inverter
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1330–AV–80~240
(RNYM01–1330–AV–B–80~240)
Mass 10kg
(Mass 11kg)
356 (388)
46
46
60
5
81
11
152
124 ( 124)
60
47
30H8
92
79
46
33.3
.5
R1
46
A
8
31.4
85h7
85h7
1.35
30.6
22
A
17.5
110
9
92
108
128
5
A-A
9
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
4- 11
47
79
152
3.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
81
Motor
1
Speed n
RNYM Series Hollow Shaft Type
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
0.58
5.83 11.7 (120Hz)
131
13.4
0.49
4.86
9.72 (120Hz)
157
16.0
0.36
3.65
7.29 (120Hz)
210
21.4
0.29
2.92
5.83 (120Hz)
262
26.7
0.24
2.43
4.86 (120Hz)
315
32.1
0.19
1.94
3.89 (120Hz)
0.15
1.46
2.92 (120Hz)
0.12
1.22
2.43 (120Hz)
390
393
390
520
390
630
39.8
40.1
39.8
53.5
39.8
64.2
Allowable Pro
N
kgf
60Hz
60Hz
4360
445
6230
635
4360
445
6230
635
4360
445
6230
635
4360
445
6230
635
4360
445
6230
635
4360
445
6230
635
4360
445
6230
635
4360
445
6230
635
SF
2.00
4.00
2.00
4.00
1.86
3.49
1.49
2.79
1.24
2.32
✻
1.86
✻
1.39
✻
1.16
Outline
Drawing
Fig.
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
01
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1440
1540
1440
1540
1440
1540
1440
1540
1440
1540
1440
1540
1440
1540
1440
1540
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
5
6
5
6
5
6
5
6
5
6
5
6
5
6
5
6
– 300
– 300
– 360
– 360
– 480
– 480
– 600
– 600
– 720
– 720
– 900
– 900
– 1200
– 1200
– 1440
– 1440
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model, voltage, and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM01–1440–300~1440
Mass 15.5kg
(RNYM01–1440–AV–B–300~1440)
(Mass 17kg)
Fig. 5
427
59
59
70
5
453
163
70
105
118
125
10
4-φ14
128
54
4-φ14
92
178
□90
11
178
108
92
φ124
70
54
□90
A
10
A
54
44
92
178
Without brake
RNYM01–1540–AV–300~1440
(RNYM01–1540–AV–B–300~1440)
Fig. 6
11
108
92
φ20
138
A-A
φ35H8
52
178
38.3
.5
R1
52
A
70
54
10
φ37
φ95h7
φ95h7
1.75
φ35.6
A
26
163
128
5
44
With brake
Mass 24.5kg
(Mass 25.5kg)
471
84
4-φ18
10
136
84
64
□112
A
64
109
213
10
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
82
4-φ18
A
64
109
213
54
128
14
φ45H8
128
67
156
A-A
213
129
109
48.8
R
67
197
A
84
64
14
1.
5
φ47.5
φ110h7
φ110h7
1.95
φ45.6
30
497
197
A
□112
84
5
14
68
213
129
109
68
φ124
5
60Hz 1750r/min
φ124
kW
0.1kW Motor for inverter
φ124
0.1
54
With brake
3. Dimensions and masses in the drawings are subject to change
without notice.
0.2kW Motor for inverter
0.2
RNYM Series Hollow Shaft Type
SF
2.00
Allowable Pro
N
kgf
60Hz
60Hz
834
85
25.0
250
500 (120Hz)
6.50
0.663
2.00
932
95
17.5
175
350 (120Hz)
9.29
0.947
2.00
1030
105
14.6
11.7
8.75
7.00
5.83
4.38
3.50
2.92
146
117
87.5
70.0
58.3
43.8
35.0
29.2
292 (120Hz)
234 (120Hz)
175 (120Hz)
140 (120Hz)
117 (120Hz)
87.6 (120Hz)
70.0 (120Hz)
58.4 (120Hz)
1.14
1.42
1.89
2.37
2.84
3.79
4.74
5.68
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
1080
1180
1320
1370
1470
2550
2750
2840
110
120
135
140
150
260
280
290
11.1
13.9
18.6
23.2
27.9
37.2
46.4
55.7
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
02
02
02
02
02
02
02
02
02
02
02
02
02
02
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1210
1220
1210
1220
1210
1220
1220
1220
1220
1220
1220
1320
1320
1320
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
5
7
7
10
10
12
15
20
25
30
40
50
60
60Hz
1750r/min
kW
Outline
Drawing
Fig.
1
2
1
2
1
2
Hollow Shaft
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
700 (120Hz)
350
35.0
4.64
0.474
Motor
Speed n1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Fig. 1
Motor for
inverter
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1210–AV–5~10
(RNYM02–1210–AV–B–5~10)
Mass 9.0kg
(Mass 10kg)
311 (343)
112
5
37
46
37
61
5
A
46
37
28.3
92
5
1.
R
124( 124)
46
37
8
14
25.6
1.35
26.2
78h8
78h8
22
25H8
38
4- 9
92
37
Fig. 2
74
37
92
A-A
9
128
A
38
1.5
9
RNYM02–1220–AV–5~30
(RNYM02–1220–AV–B–5~30)
Mass 9.5kg
(Mass 11kg)
353 (385)
49
5
1.
38
25H8
92
A
A-A
5
Fig. 3
37
37
90
28
A
R
38
96
124 ( 124)
26.2
78h7
1.35
78h7
8
4- 9
40
128
22
115
66
49
57
40
9
28.3
74
25.6
9
57
113
20
5
RNYM02–1320–AV–40~60
(RNYM02–1320–AV–B–40~60)
Mass 11kg
(Mass 13kg)
112
46
46
381 (413)
58
5
A
30.6
22
27.5
58
46
124 ( 124)
46
110
132
74
62
1.
5
R
46
33.3
8
31.4
85h7
1.35
85h7
119
30H8
128
5
A
A-A
4- 11
46
9
92
9
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
62
130
34
3. Dimentions and Masses in the drawings are subject to change
without notice.
83
0.2
0.2kW Motor for inverter
kW RNYM Series Hollow Shaft Type
6Hz
2.19
1.75
1.46
1.17
0.875
0.729
0.58
0.49
0.36
0.29
0.24
0.19
0.15
0.12
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
60Hz Allowable max speed 60Hz
60Hz
21.9
43.8 (120Hz)
74.3
7.58
17.5
35.0 (120Hz)
92.9
9.47
14.6
29.2 (120Hz)
111
11.4
11.7
23.4 (120Hz)
139
14.2
8.75 17.5 (120Hz)
186
18.9
7.29 14.6 (120Hz)
223
22.7
5.83 11.7 (120Hz) 262
26.7
4.86 9.72 (120Hz) 315
32.1
3.65 7.29 (120Hz) 420
42.8
2.92 5.83 (120Hz) 525
53.5
2.43 4.86 (120Hz) 629
64.2
1.94 3.89 (120Hz) 732
74.6
1.46 2.92 (120Hz) 732
74.6
1.22 2.43 (120Hz) 732
74.6
Motor
Speed n1
Allowable Pro
N
kgf
60Hz
60Hz
4270
435
4360
445
4360
445
4360
445
4360
445
4360
445
6230
635
6230
635
6230
635
6230
635
6230
635
6230
635
6230
635
6230
635
SF
2.00
2.00
2.00
2.00
2.00
1.80
2.00
2.00
1.74
1.39
1.16
＊
＊
＊
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1430
1430
1430
1430
1430
1430
1540
1540
1540
1540
1540
1540
1540
1540
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
1750r/min
Outline
Drawing
Fig.
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
02
02
02
02
02
02
02
02
02
02
02
02
02
02
60Hz
– 80
– 100
– 120
– 150
– 200
– 240
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
4
5
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM02–1430–AV–80~240
(RNYM02–1430–AV–B–80~240)
Fig. 4
Mass 16kg
(Mass 17kg)
404 (436)
5
130
70
A
35.6
35H8
52
124 ( 124)
128
52
178
38.3
37
.5
R1
14
70
54
10
108
92
26
1.75
20
138
10
118
A-A
4- 14
10
A
54
92
178
RNYM02–1540–AV–300~1440
(RNYM02–1540–AV–B–300~1440)
Fig. 5
8
Mass 26kg
(Mass 27.5kg)
491
84
φ45H8
84
64
84
64
A
156
A-A
4-φ18
10
136
64
109
213
10
Without brake
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
84
4-φ18
54
128
67
128
67
197
A
14
R
1.
48.8
5
14
213
129
109
φ45.6
φ47.5
φ110h7
φ110h7
1.95
□112
A
30
517
197
□112
84
5
14
68
213
129
109
68
φ124
5
φ124
95h7
59
59
105
95h7
5
A
64
109
213
54
With brake
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.4kW Motor for inverter
0.4
RNYM Series Hollow Shaft Type
1.88
Allowable Pro
N
kgf
60Hz
60Hz
1370
140
SF
25.0
250
500 (120Hz)
13.0
1.33
1.88
1570
160
17.5
175
350 (120Hz)
18.6
1.89
1.88
1720
175
14.6
11.7
8.75
7.00
5.83
4.38
3.50
2.92
146
117
87.5
70.0
58.3
43.8
35.0
29.2
292 (120Hz)
234 (120Hz)
175 (120Hz)
140 (120Hz)
117 (120Hz)
87.6 (120Hz)
70.0 (120Hz)
58.4 (120Hz)
22.3
27.9
37.2
46.4
55.7
74.3
92.9
111
2.27
2.84
3.79
4.74
5.68
7.58
9.47
11.4
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1.88
1810
1960
2160
2260
2350
3820
4020
4170
185
200
220
230
240
390
410
425
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
05
05
05
05
05
05
05
05
05
05
05
05
05
05
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1310
1320
1310
1320
1310
1320
1320
1320
1320
1320
1320
1420
1420
1420
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
5
7
7
10
10
12
15
20
25
30
40
50
60
60Hz
1750r/min
kW
Outline
Drawing
Fig.
1
2
1
2
1
2
Hollow Shaft
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
700 (120Hz)
350
35.0
9.29
0.947
Motor
Speed n1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
46
116
46
390 (433)
5
76
56
17
56
44
112
33.3
5
1.
R
85h7
56
44
8
31.4
1.35
85h7
A
30.6
22
155( 155)
5
Mass 13kg
(Mass 16kg)
113
Fig. 1
Motor for
inverter
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1310–AV–5~10
(RNYM05–1310–AV–B–5~10)
46
30H8
110
4- 11
A-A
A
44
44
138
46
2
112
92
9
RNYM05–1320–AV–5~30
(RNYM05–1320–AV–B–5~30)
Fig. 2
Mass 15kg
(Mass 17kg)
112
46
423 (466)
5
58
119
30.6
22
A
27.5
58
74
46
62
33.3
132
1.
5
R
46
46
8
31.4
85h7
85h7
1.35
30H8
110
A
4- 11
A-A
138
46
85.5
5
46
62
130
9
Fig. 3
92
155 ( 155)
9
34
9
RNYM05–1420–AV–40~60
(RNYM05–1420–AV–B–40~60)
Mass 18kg
(Mass 20kg)
474 (517)
5
70
93
20
52
35H8
A-A
A
4- 14
57
75
155
10
118
138
138
155 ( 155)
70
57
.5
R1
52
A
10
37
95h7
95h7
1.75
158
26
146
88
75
59
38.3
59
35.6
5
43
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
85
0.4
0.4kW Motor for inverter
kW RNYM Series Hollow Shaft Type
6Hz
2.19
1.75
1.46
1.17
0.875
0.729
0.583
0.486
0.365
0.292
0.243
0.194
0.146
0.122
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
60Hz Allowable max speed 60Hz
60Hz
21.9
43.8 (120Hz)
149
15.2
17.5
35.0 (120Hz)
186
18.9
14.6
29.2 (120Hz)
223
22.7
11.7
23.4 (120Hz)
279
28.4
8.75 17.5 (120Hz)
372
37.9
7.29 14.6 (120Hz)
446
45.5
5.83 11.7 (120Hz)
525
53.5
4.86 9.72 (120Hz)
630
64.2
3.65 7.29 (120Hz)
840
85.6
2.92 5.83 (120Hz)
1050
107
2.43 4.86 (120Hz)
1260
128
1.94 3.89 (120Hz)
1480
151
1.46 2.92 (120Hz)
1480
151
1.22 2.43 (120Hz)
1480
151
Motor
Speed n1
Allowable Pro
N
kgf
60Hz
60Hz
6130
625
6230
635
6230
635
6230
635
6230
635
6230
635
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
SF
1.88
1.88
1.88
1.88
1.88
1.69
2.00
2.00
1.76
1.41
1.18
＊
＊
＊
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
05
05
05
05
05
05
05
05
05
05
05
05
05
05
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1530
1530
1530
1530
1530
1530
1640
1640
1640
1640
1640
1640
1640
1640
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
60Hz
1750r/min
Outline
Drawing
Fig.
– 80
– 100
– 120
– 150
– 200
– 240
– 300
– 360
– 480
– 600
– 720
– 900
– 1200
– 1440
4
5
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM05–1530–AV–80~240
(RNYM05–1530–AV–B–80~240)
Fig. 4
Mass 25kg
(Mass 28kg)
498 (541)
84
5
A
45H8
67
4- 18
136
10
12
93
93
64
109
213
RNYM05–1640–AV–300~1440
(RNYM05–1640–AV–B–300~1440)
Fig.5
155 ( 155)
A
156
A-A
10
138
5
1.
R
67
96
14
47.5
110h7
1.95
17
30
110h7
157
213
129
84
109
64
68
48.8
68
45.6
5
9.5
Mass 68kg
(Mass 70kg)
12
604
116
160
155
85
A
224
138
280
17
55H8
145
85
170
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
113
A
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
86
3. Dimentions and Masses in the drawings are subject to change
without notice.
0.75kW Motor for inverter
0.75
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
700 (120Hz)
350
35.0
17.4
1.78
2.00
Allowable Pro
N
kgf
60Hz
60Hz
2060
210
SF
25.0
250
500 (120Hz)
24.4
2.49
2.00
2300
235
17.5
175
350 (120Hz)
34.8
3.55
2.00
2600
265
14.6
11.7
8.75
7.00
5.83
4.38
3.50
2.92
146
117
87.5
70.0
58.3
43.8
35.0
29.2
292 (120Hz)
234 (120Hz)
175 (120Hz)
140 (120Hz)
117 (120Hz)
87.6 (120Hz)
70.0 (120Hz)
58.4 (120Hz)
41.8
52.2
69.7
87.1
104
139
174
209
4.26
5.33
7.10
8.88
10.7
14.2
17.8
21.3
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2.00
2750
2940
3190
3380
3580
5540
5830
6030
280
300
325
345
365
565
595
615
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
1
1
1
1
1
1
1
1
1
1
1
1
1
1
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1410
1420
1410
1420
1410
1420
1420
1420
1420
1420
1420
1520
1520
1520
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
–
–
60Hz
1750r/min
kW
Outline
Drawing
Fig.
1
2
1
2
1
2
5
5
7
7
10
10
12
15
20
25
30
40
50
60
Hollow Shaft
RNYM Series Hollow Shaft Type
Motor
Speed n1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
5
59
150
59
Mass 22kg
(Mass 26kg)
428 (490)
5
66
90
132
A
52
35H8
138
55
4- 11
118
4
10
RNYM1–1420–AV–5~30
(RNYM1–1420–AV–B–5~30)
Fig. 2
55
132
A-A
10
143
52
66
55
38.3
.5
R1
22
66
55
35.6
10
37
95h7
95h7
1.75
118
A
26
167( 167)
Fig. 1
Motor for
inverter
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1–1410–AV–5~10
(RNYM1–1410–AV–B–5~10)
Mass 22kg
(Mass 26kg)
504 (566)
5
70
98
20
52
A-A
A
4- 14
534 (596)
84
5
45.6
14
45H8
4- 14
A
70
80
175
10
136
143
156
A-A
167 ( 167)
67
28
R
1.
5
47.5
110h7
67
91
A
30
1.95
110h7
178
84
70
150
68
178
68
43
Mass 31kg
(Mass 35kg)
94
80
5
75
155
RNYM1–1520–AV–40~60
(RNYM1–1520–AV–B–40~60)
Fig. 3
57
10
48.8
118
143
35H8
138
10
167 ( 167)
70
57
.5
R1
52
A
10
37
95h7
95h7
1.75
158
26
146
88
75
59
38.3
59
35.6
5
68
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
87
0.75
0.75kW Motor for inverter
kW RNYM Series Hollow Shaft Type
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
2.19
21.9 43.8 (120Hz)
279
28.4
1.75
17.5 35.0 (120Hz)
348
35.5
1.46
14.6 29.2 (120Hz)
418
42.6
1.17
11.7 23.3 (120Hz)
522
53.3
0.875
8.75 17.5 (120Hz)
697
71.0
0.729
7.29 14.6 (120Hz)
836
85.2
Motor
Speed n1
SF
2.00
2.93
2.93
2.83
2.13
1.77
Allowable Pro
N
kgf
60Hz
60Hz
6130
625
9810
1000
9810
1000
9810
1000
9810
1000
9810
1000
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
1
1
1
1
1
1
–
–
–
–
–
–
1531
1630
1630
1631
1631
1631
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
60Hz
1750r/min
Outline
Drawing
Fig.
4
80
100
120
150
200
240
5
6
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM1–1531–AV–80
(RNYM1–1531–AV–B–80)
Fig. 4
Mass 30kg
(Mass 34kg)
528 (590)
84
5
84
64
A
156
A-A
4- 18
136
12
93
93
64
10
RNYM1–1630–AV–100~120
(RNYM1–1630–AV–B–100~120)
Fig. 5
143
45H8
67
17
5
1.
R
67
167 ( 167)
45.6
14
47.5
110h7
110h7
1.95
101
A
30
10
157
213
68
129
109
68
48.8
5
109
213
9.5
Mass 52kg
(Mass 56kg)
12
593
A
55.6
160
167
164
85
143
27
55H8
145
85
170
85
280
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
118
40
A
224
A-A
19
186
4- 22
19
85
145
110
170
280
RNYM1–1631–AV–150~240
(RNYM1–1631–AV–B–150~240)
Fig. 6
12
93
93
Mass 53kg
(Mass 57kg)
12
605
118
A
160
143
27
A
224
167
164
85
145
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
88
3. Dimentions and Masses in the drawings are subject to change
without notice.
1.5kW Motor for inverter
1.5
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
700 (120Hz)
350
35.0
34.8
3.55
SF
25.0
250
500 (120Hz)
48.8
4.97
17.5
175
350 (120Hz)
69.7
7.10
3.67
1.47
2.47
1.47
1.47
14.6
11.7
8.75
7.00
5.83
4.38
3.50
2.92
146
117
87.5
70.0
58.3
43.8
35.0
29.2
292 (120Hz)
234 (120Hz)
175 (120Hz)
140 (120Hz)
117 (120Hz)
87.6 (120Hz)
70.0 (120Hz)
58.4 (120Hz)
83.6
104
139
174
209
279
348
418
8.52
10.7
14.2
17.8
21.3
28.4
35.5
42.6
1.47
1.47
1.47
1.47
1.47
1.47
1.47
1.47
Allowable Pro
N
kgf
60Hz
60Hz
2940
300
3330
340
3730
380
3970
4220
4610
4900
5150
5540
5830
6030
405
430
470
500
525
565
595
615
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
2
2
2
2
2
2
2
2
2
2
2
2
2
2
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1510
1520
1510
1520
1510
1520
1520
1520
1520
1520
1520
1531
1531
1531
–
–
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
5
7
7
10
10
12
15
20
25
30
40
50
60
60Hz
1750r/min
kW
Outline
Drawing
Fig.
1
2
1
2
1
2
Hollow Shaft
RNYM Series Hollow Shaft Type
Motor
Speed n1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
478 (541)
77
30
156
4- 11
A-A
A
65
65
154
136
RNYM2–1520–AV–5~30
(RNYM2–1520–AV–B–5~30)
553 (616)
5
84
45.6
14
R
45H8
67
180 ( 180)
1.
5
47.5
110h7
67
96
A
30
1.95
110h7
178
28
150
68
84
70
68
178
5
Mass 34kg
(Mass 39kg)
94
80
Fig. 2
3
10
48.8
10
180( 180)
154
45H8
67
27
5
1.
R
67
77
65
124
14
47.5
110h7
110h7
1.95
100
A
150
5
77
65
164
68
68
48.8
5
Mass 29kg
(Mass 35kg)
45.6
Fig. 1
4- 14
A-A
150
156
A
70
80
175
10
136
68
10
RNYM2–1531–AV–40~60
(RNYM2–1531–AV–B–40~60)
Fig. 3
Motor for
inverter
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM2–1510–AV–5~10
(RNYM2–1510–AV–B–5~10)
Mass 34kg
(Mass 39kg)
548 (611)
84
5
45H8
4- 18
136
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
180 ( 180)
17
A
156
A-A
64
109
213
150
67
213
5
1.
R
67
84
64
14
47.5
110h7
110h7
1.95
124
A
30
10
157
129
109
68
48.8
68
45.6
5
9.5
3. Dimentions and Masses in the drawings are subject to change
without notice.
89
1.5
1.5kW Motor for inverter
kW RNYM Series Hollow Shaft Type
Motor
Speed n1
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
6Hz
60Hz Allowable max speed 60Hz
60Hz
2.19
21.9 43.8 (120Hz) 557
56.8
1.47
Allowable Pro
N
kgf
60Hz
60Hz
9660
985
1.75
17.5
35.0 (120Hz)
697
71.0
1.47
9810
1000
1.46
14.6
29.2 (120Hz)
836
85.2
1.47
9810
1000
1.17
0.875
0.729
11.7 23.3 (120Hz) 1040
8.75 17.5 (120Hz) 1390
7.29 14.6 (120Hz) 1480
1.42
1.06
*
9810
9810
9810
1000
1000
1000
SF
107
142
151
–
–
–
–
–
–
–
–
–
60
1630
60
1630
60
1630
1631
1631
1631
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
1750r/min
Outline
Drawing
Fig.
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
2
2
2
2
2
2
2
2
2
60Hz
4
5
4
5
4
5
80
80
100
100
120
120
150
200
240
6
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM2–60–AV–80~120
(RNYM2–60–AV–B–80~120)
Fig. 4
12
93
93
Mass 90kg
(Mass 97kg)
624 (687)
12
85
4- 22
A-A
180 ( 180)
27
160
55H8
32
19
A
150
85
224
186
280
170
110
145
85
.5
R2
85
19
A
16
58
150h7
150h7
2.2
59.3
40
45.6
164
145
110
170
280
RNYM2–1630–AV–80~120
(RNYM2–1630–AV–B–80~120)
Fig. 5
12
93
93
Mass 57kg
(Mass 63kg)
624
12
124
A
160
180
164
85
280
150
55H8
27
85
145
85
170
R
2.
5
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A
224
A-A
19
186
19
85
4- 22
145
110
170
280
RNYM2–1631–AV–150~240
(RNYM2–1631–AV–B–150~240)
Fig. 6
12
93
93
Mass 57kg
(Mass 63kg)
624
12
124
A
160
150
27
A
224
180
164
85
145
55H8
170
85
280
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
90
3. Dimentions and Masses in the drawings are subject to change
without notice.
2.2kW Motor for inverter
2.2
RNYM Series Hollow Shaft Type
14.6
11.7
8.75
7.00
5.83
4.38
3.50
Allowable Pro
N
kgf
60Hz
60Hz
2940
300
3330
340
5930
605
3730
380
6330
645
3970
405
6670
680
4220
430
7350
750
4610
470
7750
790
4900
500
8090
825
8480
865
8880
905
SF
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
1.68
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
3
3
3
3
3
3
3
3
3
3
3
3
3
3
3
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1521 –
1521 –
63 –
1521 –
63 –
1521 –
63 –
1521 –
63 –
1521 –
63 –
1521 –
63 –
63 –
63 –
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7
10
10
12
12
15
15
20
20
25
25
30
40
50
60Hz
1750r/min
kW
Outline
Drawing
Fig.
2
1
2
1
2
1
2
1
2
1
2
Hollow Shaft
6Hz
35.0
25.0
17.5
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
60Hz Allowable max speed 60Hz
60Hz
350
350 (60Hz)
5.21
51.1
250
250 (60Hz)
7.29
71.5
175
350 (120Hz)
10.4
102.2
10.4
175 (60Hz)
102
146
12.5
292 (120Hz)
123
12.5
146 (60Hz)
123
117
15.6
234 (120Hz)
153
15.6
117 (60Hz)
153
87.5 175 (120Hz)
20.8
204
20.8
204
87.5 (60Hz)
26.0
70.0 140 (120Hz)
255
26.0
255
70.0 (60Hz)
31.3
58.3 117 (120Hz)
307
41.7
43.8 87.6 (120Hz) 409
52.1
35.0 70.0 (120Hz) 511
Motor
Speed n1
1
Motor for
inverter
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM3–63–AV–10~50
(RNYM3–63–AV–B–10~50)
12
677 (749)
32
68
27
612
84
178
84
70
80
28
178
94
45H8
167
R1
.5
67
156
48.8
14
47.5
110h7
110h7
67
150
45.6
A
A
A-A
4- 14
70
80
175
10
160
Mass 50kg
(Mass 61kg)
5
30
1.95
150
136
145
170
280
222
68
85
110
144
5
4- 22
A-A
19
RNYM3–1521–AV–5~25
(RNYM3–1521–AV–B–5~25)
Fig. 2
A
55H8
224
186
222 ( 222)
85
166
.5
R1
85
19
A
16
58
150h7
150h7
2.2
110
85
40
280
170
145
93
93
164
59.3
12
Mass 102kg
(Mass 111kg)
55.6
Fig. 1
68
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
91
2.2
2.2kW Motor for inverter
kW RNYM Series Hollow Shaft Type
6Hz
5.83
4.38
3.50
2.92
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
60Hz Allowable max speed 60Hz
60Hz
31.3
307
117 (120Hz)
58.3
41.7
409
43.8 87.5 (120Hz)
52.1
511
35.0 70.0 (120Hz)
62.5
613
29.2 58.3 (120Hz)
SF
1.68
1.68
1.68
1.68
Motor
Speed n1
Allowable Pro
N
kgf
60Hz
60Hz
825
8090
865
8480
905
8880
945
9270
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
3
3
3
3
–
–
–
–
1632 –
1632 –
1632 –
1632 –
AV
AV
AV
AV
–
–
–
–
60Hz
1750r/min
Outline
Drawing
Fig.
30
40
50
60
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM3–1632–AV–30~60
(RNYM3–1632–AV–B–30~60)
Fig. 3
12
93
93
Mass 69kg
(Mass 80kg)
12
677
144
A
160
222
164
85
280
27
A
224
166
55H8
145
85
170
5
2.
R
85
59.3
110
16
58
150h7
150h7
2.2
55.6
40
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
92
3. Dimentions and Masses in the drawings are subject to change
without notice.
3.7kW Motor for inverter
3.7
RNYM Series Hollow Shaft Type
14.6
11.7
8.75
7.00
5.83
4.38
Allowable Pro
N
kgf
60Hz
60Hz
2940
300
3330
340
5930
605
3730
380
6330
645
3970
405
6670
680
4220
430
7350
750
7750
790
8090
825
8480
865
SF
1.49
1.49
1.49
1.49
1.49
1.49
1.49
1.49
1.49
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
5
5
5
5
5
5
5
5
5
5
5
5
– 1522
– 1522
– 64
– 1522
– 64
– 1522
– 64
– 1522
– 64
– 64
– 64
– 64
–
–
–
–
–
–
–
–
–
–
–
–
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
AV
–
–
–
–
–
–
–
–
–
–
–
–
5
7
10
10
12
12
15
15
20
25
30
40
60Hz
1750r/min
kW
Outline
Drawing
Fig.
2
1
2
1
2
1
2
Hollow Shaft
6Hz
35.0
25.0
17.5
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
60Hz Allowable max speed 60Hz
60Hz
350
350 (60Hz)
85.9
8.76
250
250 (60Hz)
120
12.3
175
233 (80Hz)
172
17.5
175 (60Hz)
146
195 (80Hz)
206
21.0
146 (60Hz)
117
156 (80Hz)
258
26.3
117 (60Hz)
87.5
117 (80Hz)
344
35.0
70.0
93.4 (80Hz)
430
43.8
58.3
77.8 (80Hz)
516
52.6
43.8
58.4 (80Hz)
687
70.1
Motor
Speed n1
1
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
721 (793)
12
85
85
19
32
186
27
55H8
224
19
A
166
.5
R2
4- 22
A-A
85
110
222 ( 222)
16
58
150h7
2.2
A
160
40
280
170
110
145
85
93
93
164
59.3
12
Mass 110kg
(Mass 119kg)
55.6
Fig. 1
Motor for
inverter
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNYM5–64–AV–10~40
(RNYM5–64–AV–B–10~40)
145
170
280
RNYM5–1522–AV–5~15
(RNYM5–1522–AV–B–5~15)
68
68
656
5
178
84
84
70
80
28
178
45H8
166
156
94
.5
R1
67
67
48.8
14
47.5
110h7
110h7
30
1.95
150
45.6
A
222
5
Mass 57kg
(Mass 68kg)
144
Fig. 2
A
A-A
4- 14
70
80
175
68
150
10
136
10
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
93
3.7
3.7kW Motor for inverter
kW RNYM Series Hollow Shaft Type
6Hz
8.75
7.00
5.83
4.38
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
60Hz Allowable max speed 60Hz
60Hz
35.0
344
117 (80Hz)
87.5
43.8
430
93.4 (80Hz)
70.0
52.6
516
77.8 (80Hz)
58.3
70.1
687
58.3 (80Hz)
43.8
SF
1.49
1.49
1.49
1.49
Motor
Speed n1
Allowable Pro
N
kgf
60Hz
60Hz
750
7350
790
7750
825
8090
865
8480
Capacity Frame
Reduction
Symbol – Size –Suffix – Ratio
5
5
5
5
– 1633
– 1633
– 1633
– 1633
–
–
–
–
AV
AV
AV
AV
–
–
–
–
20
25
30
40
60Hz
1750r/min
Outline
Drawing
Fig.
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow shaft end to the point of radial load is 20 mm.
3. Usage of motor for inverters enables constant torque operation (continuous operation) within range of 6-60Hz.
4. Sensorless operation using our inverter (HF-320) enables constant torque operation using general-purpose motors.
Refer to page A223 for details.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
Fig. 3
12
RNYM5–1633–AV–20~40
(RNYM5–1633–AV–B–20~40)
93
93
Mass 77kg
(Mass 88kg)
12
793
144
160
222
164
85
280
A
166
55H8
27
85
224
145
85
170
R
2.
5
59.3
110
16
58
150h7
150h7
40
2.2
55.6
A
A-A
19
186
19
4- 22
85
145
110
170
280
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
94
3. Dimentions and Masses in the drawings are subject to change
without notice.
Solid Shaft
15W-90W
95
Singlephase
3-phase
Solid Shaft
15
15W 3-phase Motor
W
RNFM Series Solid shaft Flange mount type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.371
0.307 0.038
0.031
0.556
0.461 0.057
0.047
0.742
0.615 0.076
0.063
0.890
0.738 0.091
0.075
1.11
0.922 0.113
0.094
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.23
1.84
0.227
0.188
2.97
2.46
0.303
0.251
3.71
3.07
0.378
0.313
4.45
3.69
0.454
0.376
5.93
4.92
0.605
0.501
7.42
6.15
0.756
0.627
8.90
7.38
0.908
0.752
11.9
9.83
1.21
1.00
14.8
12.3
1.51
1.25
17.8
14.8
1.82
1.50
Motor
Speed n1
Allowable Pro
N
SF
4.00
4.00
4.00
4.00
4.00
4.00
4.00
3.53
2.64
2.12
1.76
1.32
1.06
3.34
2.50
2.00
1.67
50Hz
343
343
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
50Hz
35
35
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
343
343
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
50Hz
60Hz
60Hz
35
35
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
01
01
01
01
01
01
01
01
01
01
01
01
01
03
03
03
03
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM0015–01 RL –5~100
Mass 2.7kg
• Use hex socket head cap screws (M5) for installation.
(RNFM0015–01 RL –B–5~100)
(Mass 3.3kg)
175 (214)
175 (214)
22
A
4
A
15
94
4
94
76 (
80)
76 (
80
15
A
L=300
L=300
80)
8
A
40
135 (174)
8
135 (174)
80
40
23.1
22
23.1
Fig. 1
3
32
4- 5.5
80
3
32
4- 5.5
2.5
82
80
82
10h6
A-A
175 (214)
135 (174)
L=300
94
4- 5.5
7
38
80
15h6
A
15
80)
76 (
A
3
80
15
80)
5
22
40
8
L=300
5
8
A
82
• Use hex socket head cap screws (M5) for installation.
175 (214)
135 (174)
40
76 (
22
Mass 2.7kg
(Mass 3.3kg)
23.1
RNFM0015–03 RL –120~240
(RNFM0015–03 RL –B–120~240)
23.1
Fig. 2
R
80
L
A
94
7
38
4- 5.5
80
82
A-A
L
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
96
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
25W 3-phase Motor
25
Motor
Speed n1
RNFM Series Solid shaft Flange mount type
Allowable Pro
N
SF
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.12
1.59
1.27
1.06
2.40
2.40
2.00
1.50
1.20
1.00
50Hz
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
1080
1080
50Hz
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
110
110
W
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
1080
1080
1450r/min
1750r/min
60Hz
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
110
110
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
01
01
01
01
01
01
01
01
01
01
01
03
03
03
03
03
03
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
3
4
3-phase
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Solid Shaft
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
87.5
72.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.618
0.512 0.063
0.052
0.927
0.768 0.095
0.078
1.24
1.02
0.126
0.104
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.47
2.05
0.252
0.209
3.09
2.56
0.315
0.261
3.71
3.07
0.378
0.313
4.95
4.10
0.504
0.418
6.18
5.12
0.630
0.522
7.42
6.15
0.756
0.627
9.9
8.20
1.01
0.836
12.4
10.2
1.26
1.04
14.8
12.3
1.51
1.25
19.8
16.4
2.02
1.67
24.7
20.5
2.52
2.09
29.7
24.6
3.03
2.51
50Hz
60Hz
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM0025–01 RL –5~60
Mass 2.8kg
• Use hex socket head cap screws (M5) for installation.
(RNFM0025–01 RL –B–5~60)
(Mass 3.4kg)
175 (214)
175 (214)
22
A
4
A
15
94
4
94
76 (
80)
76 (
80
15
A
L=300
L=300
80)
8
A
40
135 (174)
8
135 (174)
80
40
23.1
22
23.1
Fig. 3
3
32
4- 5.5
80
3
32
4- 5.5
2.5
82
80
82
10h6
A-A
175 (214)
135 (174)
L=300
94
4- 5.5
7
38
80
15h6
A
15
80)
76 (
A
3
80
15
80)
5
22
40
8
L=300
5
8
A
82
• Use hex socket head cap screws (M5) for installation.
175 (214)
135 (174)
40
76 (
22
Mass 2.9kg
(Mass 3.5kg)
23.1
RNFM0025–03 RL –80~240
(RNFM0025–03 RL –B–80~240)
23.1
Fig. 4
R
80
L
A
94
7
38
4- 5.5
80
82
A-A
L
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
97
40
40W 3-phase Motor
W
RNFM Series Solid shaft Flange mount type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
48.3
58.3
43.8
36.3
29.0
35.0
29.2
24.2
18.1
21.9
17.5
14.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.12
0.929 0.114
0.095
1.68
1.39
0.171
0.142
2.24
1.86
0.229
0.189
2.69
2.23
0.274
0.227
3.36
2.79
0.343
0.284
4.48
3.72
0.457
0.379
5.61
4.64
0.572
0.474
6.73
5.57
0.686
0.568
8.97
7.43
0.914
0.758
11.2
9.29
1.14
0.947
13.5
11.1
1.37
1.14
17.9
14.9
1.83
1.52
22.4
18.6
2.29
1.89
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
44.8
37.2
4.57
3.79
53.8
44.6
5.49
4.55
Motor
Speed n1
Allowable Pro
SF
N
50Hz
441
490
539
588
588
588
588
588
588
588
1080
1080
1080
1080
1420
1420
1420
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.31
1.05
1.50
1.50
1.20
1.00
1.50
1.20
1.00
50Hz
45
50
55
60
60
60
60
60
60
60
110
110
110
110
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
392
441
490
539
588
588
588
588
588
588
1080
1080
1080
1080
1420
1420
1420
50Hz
60Hz
60Hz
40
45
50
55
60
60
60
60
60
60
110
110
110
110
145
145
145
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
05
05
05
05
05
05
05
05
05
05
07
07
07
07
17
17
17
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM004–05 RL –5~50
Mass 3.0kg
• Use hex socket head cap screws (M6) for installation.
Fig. 1
(RNFM004–05 RL –B–5~50)
(Mass 3.6kg)
180 (219)
180 (219)
6
45
135 (174)
L=300
L=300
22
6
135 (174)
23.1
45
23.1
22
A
18
104
90
80)
4
A
4
104
76 (
80)
76 (
A
18
90
A
3
4- 6.5
32
90
4- 6.5
2.5
82
3
90
32
82
12h6
L
RNFM004–07 RL –60~120
(RNFM004–07 RL –B–60~120)
Mass 3.1kg
(Mass 3.7kg)
• Use hex socket head cap screws (M6) for installation.
180 (219)
135 (174)
6
23.1
45
135 (174)
L=300
L=300
A
18
76 (
3
7
82
104
4- 6.5
90
38
A
5
76 (
5
104
90
80)
18
80)
A
90
A
22
45
6
180 (219)
22
23.1
Fig. 2
R
A-A
7
4- 6.5
90
38
82
15h6
A-A
L
RNFM004–17 RL –150~240
(RNFM004–17 RL –B–150~240)
Mass 3.8kg
(Mass 4.2kg)
• Use hex socket head cap screws (M6) for installation.
L=300
90 (
8
104
3.5
6
22
18
96)
96)
23.1
8
18
45
149 (208)
L=300
104
7
98
194 (253)
149 (208)
90 (
4- 6.5
90
38
6
A
90
A
45
90
194 (253)
22
23.1
Fig. 3
R
A
A
7
4- 6.5
90
38
98
18h6
L
98
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
60W 3-phase Motor
60
Motor
Speed n1
RNFM Series Solid shaft Flange mount type
Allowable Pro
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.50
1.50
1.34
1.07
✻
✻
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1420
1420
1420
1420
1420
1420
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1370
1420
1420
1420
1420
1420
50Hz
55
60
65
70
75
80
85
90
100
110
110
145
145
145
145
145
145
60Hz
50
55
60
65
70
75
80
85
95
105
110
140
145
145
145
145
145
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
07
07
07
07
07
07
07
07
07
07
07
17
17
17
17
17
17
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
4
5
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
W
Solid Shaft
SF
1450r/min
1750r/min
3-phase
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.68
1.39
0.171
0.142
2.52
2.09
0.257
0.213
3.36
2.79
0.343
0.284
4.04
3.34
0.412
0.341
5.04
4.18
0.514
0.426
6.73
5.57
0.686
0.568
8.41
6.97
0.857
0.710
10.1
8.36
1.03
0.852
13.5
11.1
1.37
1.14
16.8
13.9
1.71
1.42
20.2
16.7
2.06
1.70
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
50Hz
60Hz
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM006–07 RL –5~60
Mass 3.1kg
• Use hex socket head cap screws (M6) for installation.
(RNFM006–07 RL –B–5~60)
(Mass 3.6kg)
180 (219)
135 (174)
6
23.1
45
135 (174)
L=300
L=300
A
18
76 (
3
7
82
104
4- 6.5
90
38
A
5
76 (
5
104
90
80)
18
80)
A
90
A
22
45
6
180 (219)
22
23.1
Fig. 4
7
4- 6.5
90
38
82
15h6
A-A
L
RNFM006–17 RL –80~240
(RNFM006–17 RL –B–80~240)
Mass 4.0kg
(Mass 4.4kg)
• Use hex socket head cap screws (M6) for installation.
L=300
90 (
8
104
3.5
6
22
18
96)
96)
23.1
8
18
45
149 (208)
L=300
104
7
98
194 (253)
149 (208)
90 (
4- 6.5
90
38
6
A
90
A
45
90
194 (253)
22
23.1
Fig. 5
R
A
A
7
4- 6.5
90
38
98
18h6
L
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
99
90
90W 3-phase Motor
W
RNFM Series Solid shaft Flange mount type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
43.8
36.3
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.257
2.09
2.52
0.213
0.386
3.13
3.78
0.320
0.514
4.18
5.04
0.426
0.617
5.02
6.05
0.511
0.772
6.27
7.57
0.639
1.03
8.36
10.1
0.852
1.29
10.4
12.6
1.07
12.5
1.54
15.1
1.28
16.7
2.06
20.2
1.70
20.9
25.2
2.57
2.13
25.1
30.3
3.09
2.56
33.4
40.4
4.12
3.41
41.8
50.4
5.14
4.26
50.2
53.9
5.50
5.11
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
Motor
Speed n1
Allowable Pro
SF
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
✻
✻
✻
✻
N
50Hz
539
588
637
686
735
785
834
883
981
1270
1320
1420
1420
1420
1420
1420
1420
50Hz
55
60
65
70
75
80
85
90
100
130
135
145
145
145
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame Reduction
Drawing
–
–
Symbol
Size
Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1230
1270
1370
1420
1420
1420
1420
1420
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
125
130
140
145
145
145
145
145
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
15
15
15
15
15
15
15
15
15
15
15
17
17
17
17
17
17
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
—
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM009–15 RL –5~60
Mass 4.3kg
• Use hex socket head cap screws (M6) for installation.
(RNFM009–15 RL –B–5~60)
(Mass 4.7kg)
L=300
8
104
A
A
5
3
76 (
5
22
18
80)
18
104
45
80)
L=300
23.1
8
149 (208)
76 (
A
90
A
194 (253)
149 (208)
45
90
194 (253)
22
23.1
Fig. 1
7
98
4- 6.5
90
38
7
4- 6.5
90
38
98
15h6
A-A
L
R
RNFM009–17 RL –80~240
(RNFM009–17 RL –B–80~240)
Mass 4.3kg
(Mass 4.7kg)
• Use hex socket head cap screws (M6) for installation.
L=300
90 (
8
104
3.5
6
22
18
96)
96)
23.1
8
18
45
149 (208)
L=300
104
7
98
194 (253)
149 (208)
90 (
4- 6.5
90
38
6
A
90
A
45
90
194 (253)
22
23.1
Fig. 2
A
A
7
4- 6.5
90
38
98
18h6
L
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
100
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
Solid Shaft
MEMO
3-phase
90
W
101
15
15W Single-phase Motor
W
RNFM Series Solid shaft Flange mount type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
17.5
14.5
14.6
12.1
9.06 10.9
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.371
0.307 0.038
0.031
0.556
0.461 0.057
0.047
0.742
0.615 0.076
0.063
0.890
0.738 0.091
0.075
1.11
0.922 0.113
0.094
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.23
1.84
0.227
0.188
2.97
2.46
0.303
0.251
3.71
3.07
0.378
0.313
4.45
3.69
0.454
0.376
5.93
4.92
0.605
0.501
7.42
6.15
0.756
0.627
8.90
7.38
0.908
0.752
11.9
9.83
1.21
1.00
14.8
12.3
1.51
1.25
17.8
14.8
1.82
1.50
Motor
Speed n1
Allowable Pro
SF
4.00
4.00
4.00
4.00
4.00
4.00
4.00
3.53
2.64
2.12
1.76
1.32
1.06
3.34
2.50
2.00
1.67
N
50Hz
343
343
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
50Hz
35
35
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
343
343
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
50Hz
60Hz
60Hz
35
35
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
01 –
01 –
01 –
01 –
01 –
01 –
01 –
01 –
01 –
01 –
01 –
01 –
01 –
03 –
03 –
03 –
03 –
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM0015–01 RL –CA–5~100
Mass 2.7kg
• Use hex socket head cap screws (M5) for installation.
(RNFM0015–01 RL –CA–B–5~100)
(Mass 3.3kg)
A
80
15
80)
4
76 (
A
94
82
3
32
2.5
4
94
76 (
80
15
A
22
40
23.1
L=300
L=300
80)
A
175 (214)
135 (174)
8
175 (214)
135 (174)
40
8
22
23.1
Fig. 1
4- 5.5
80
4- 5.5
3
32
80
L
10h6
82
R
A-A
Mass 2.7kg
(Mass 3.3kg)
• Use hex socket head cap screws (M5) for installation.
A
80)
5
4- 5.5
80
5
3
7
38
76 (
80)
94
76 (
80
15
A
82
L=300
L=300
L
22
40
135 (174)
8
23.1
8
A
175 (214)
135 (174)
15
40
80
175 (214)
22
23.1
RNFM0015–03 RL –CA–120~240
(RNFM0015–03 RL –CA–B–120~240)
Fig. 2
A
94
7
38
4- 5.5
80
82
R
15h6
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
102
3. Dimentions and Masses in the drawings are subject to change
without notice.
25W Single-phase Motor
25
Motor
Speed n1
RNFM Series Solid shaft Flange mount type
Allowable Pro
SF
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.12
1.59
1.27
1.06
2.40
2.40
2.00
1.50
1.20
1.00
N
50Hz
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
1080
1080
50Hz
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
110
110
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
1080
1080
1450r/min
1750r/min
60Hz
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
110
110
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
01
01
01
01
01
01
01
01
01
01
01
03
03
03
03
03
03
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
3
4
Solid Shaft
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
87.5
72.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
7.25
8.75
6.04
7.29
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.618
0.512 0.063
0.052
0.927
0.768 0.095
0.078
1.24
1.02
0.126
0.104
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.47
2.05
0.252
0.209
3.09
2.56
0.315
0.261
3.71
3.07
0.378
0.313
4.95
4.10
0.504
0.418
6.18
5.12
0.630
0.522
7.42
6.15
0.756
0.627
9.9
8.20
1.01
0.836
12.4
10.2
1.26
1.04
14.8
12.3
1.51
1.25
19.8
16.4
2.02
1.67
24.7
20.5
2.52
2.09
29.7
24.6
3.03
2.51
50Hz
60Hz
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
A
80
15
80)
4
76 (
A
94
82
3
32
2.5
4
94
76 (
80
15
A
22
40
23.1
L=300
L=300
80)
A
175 (214)
135 (174)
8
175 (214)
135 (174)
40
8
22
23.1
Fig. 3
Singlephase
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM0025–01 RL –CA–5~60
Mass 2.8kg
• Use hex socket head cap screws (M5) for installation.
(RNFM0025–01 RL –CA–B–5~60)
(Mass 3.4kg)
4- 5.5
80
4- 5.5
3
32
80
L
10h6
82
R
A-A
Mass 2.9kg
(Mass 3.5kg)
• Use hex socket head cap screws (M5) for installation.
A
80)
5
4- 5.5
80
5
3
7
38
76 (
80)
94
76 (
80
15
A
82
L=300
L=300
L
22
40
135 (174)
8
23.1
8
A
175 (214)
135 (174)
15
40
80
175 (214)
22
23.1
RNFM0025–03 RL –CA–80~240
(RNFM0025–03 RL –CA–B–80~240)
Fig. 4
A
94
7
38
4- 5.5
80
82
R
15h6
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimentions and Masses in the drawings are subject to change
without notice.
103
40
40W Single-phase Motor
W
RNFM Series Solid shaft Flange mount type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.12
0.929 0.114
0.095
1.68
1.39
0.171
0.142
2.24
1.86
0.229
0.189
2.69
2.23
0.274
0.227
3.36
2.79
0.343
0.284
4.48
3.72
0.457
0.379
5.61
4.64
0.572
0.474
6.73
5.57
0.686
0.568
8.97
7.43
0.914
0.758
11.2
9.29
1.14
0.947
13.5
11.1
1.37
1.14
17.9
14.9
1.83
1.52
22.4
18.6
2.29
1.89
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
44.8
37.2
4.57
3.79
53.8
44.6
5.49
4.55
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
17.5
14.5
14.6
12.1
9.67 11.7
8.75
7.25
7.29
6.04
Motor
Speed n1
Allowable Pro
SF
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.31
1.05
1.50
1.50
1.20
1.00
1.60
1.20
1.00
N
50Hz
441
490
539
588
588
588
588
588
588
588
1080
1080
1080
1080
1420
1420
1420
50Hz
45
50
55
60
60
60
60
60
60
60
110
110
110
110
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
392
441
490
539
588
588
588
588
588
588
1080
1080
1080
1080
1420
1420
1420
50Hz
60Hz
60Hz
40
45
50
55
60
60
60
60
60
60
110
110
110
110
145
145
145
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
05
05
05
05
05
05
05
05
05
05
07
07
07
07
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM004–05 RL –CA–5~50
Mass 3.0kg
• Use hex socket head cap screws (M6) for installation.
Fig. 1
(RNFM004–05 RL –CA–B–5~50)
(Mass 3.6kg)
219(219)
219 (219)
L=300
22
45
L=300
6
6
174
23.1
174
45
23.1
22
A
18
4
104
A
82
3
4- 6.5
32
90
2.5
4
104
90
80
80
A
18
90
A
4- 6.5
3
32
90
82
12h6
L
R
A-A
RNFM004–07 RL –CA–60~120
(RNFM004–07 RL –CA–B–60~120)
Mass 3.1kg
(Mass 3.7kg)
• Use hex socket head cap screws (M6) for installation.
219 (219)
219 (219)
6
174
L=300
22
45
L=300
6
174
45
23.1
22
23.1
Fig. 2
A
82
7
4- 6.5
38
90
18
90
104
A
5
5
3
104
80
18
80
A
90
A
4- 6.5
7
90
38
82
15h6
L
R
A-A
RNFM004–17 RL –CA–150~240
(RNFM004–17 RL –CA–B–150~240)
Mass 4.3kg
(Mass 4.7kg)
• Use hex socket head cap screws (M6) for installation.
90
45
22
8
18
96)
3.5
4- 6.5
38
90 (
96)
18
6
6
23.1
8
L=300
L=300
104
7
98
149 (208)
90 (
A
90
A
194 (253)
149 (208)
45
A
90
194 (253)
22
23.1
Fig. 3
A
104
4- 6.5
7
90
38
98
18h6
L
104
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
60W Single-phase Motor
60
Motor
Speed n1
RNFM Series Solid shaft Flange mount type
Allowable Pro
SF
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.34
1.07
✻
✻
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1420
1420
1420
1420
1420
1420
50Hz
55
60
65
70
75
80
85
90
100
110
110
145
145
145
145
145
145
60Hz
50
55
60
65
70
75
80
85
95
105
110
140
145
145
145
145
145
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
15
15
15
15
15
15
15
15
15
15
15
17
17
17
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
4
5
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
18
8
23.1
104
3
5
5
4- 6.5
90
38
22
45
96
23.1
18
8
L=300
L=300
104
7
98
186 (226)
96
A
90
A
231 (271)
186 (226)
45
A
A
4- 6.5
7
90
38
15h6
L
90
231 (271)
22
Singlephase
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM006–15 RL –CA–5~60
Mass 4.3kg
• Use hex socket head cap screws (M6) for installation.
(RNFM006–15 RL –CA–B–5~60)
(Mass 4.7kg)
Fig. 4
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1370
1420
1420
1420
1420
1420
1450r/min
1750r/min
Solid Shaft
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
87.5
72.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.68
1.39
0.171
0.142
2.52
2.09
0.257
0.213
3.36
2.79
0.343
0.284
4.04
3.34
0.412
0.341
5.04
4.18
0.514
0.426
6.73
5.57
0.686
0.568
8.41
6.97
0.857
0.710
10.1
8.36
1.03
0.852
13.5
11.1
1.37
1.14
16.8
13.9
1.71
1.42
20.2
16.7
2.06
1.70
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
50Hz
60Hz
98
R
A-A
Mass 4.5kg
(Mass 4.9kg)
• Use hex socket head cap screws (M6) for installation.
L=300
6
22
8
18
104
A
A
6
3.5
104
45
96
23.1
L=300
18
8
186 (226)
96
A
90
A
231 (271)
186 (226)
45
90
231 (271)
22
23.1
RNFM006–17 RL –CA–80~240
(RNFM006–17 RL –CA–B–80~240)
Fig. 5
7
98
4- 6.5
90
38
7
4- 6.5
90
38
98
18h6
L
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
105
90
90W Single-phase Motor
W
RNFM Series Solid shaft Flange mount type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
43.8
36.3
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
2.09
2.52
0.257
0.213
3.13
3.78
0.386
0.320
4.18
5.04
0.514
0.426
5.02
6.05
0.617
0.511
6.27
7.57
0.772
0.639
8.36
10.1
1.03
0.852
10.4
12.6
1.29
1.07
15.1
12.5
1.54
1.28
20.2
16.7
2.06
1.70
25.2
20.9
2.57
2.13
30.3
25.1
3.09
2.56
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
50.2
5.50
5.11
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
Motor
Speed n1
Allowable Pro
SF
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
✻
✻
✻
✻
N
50Hz
539
588
637
686
735
785
834
883
981
1270
1320
1420
1420
1420
1420
1420
1420
50Hz
55
60
65
70
75
80
85
90
100
130
135
145
145
145
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
490
539
588
637
686
735
785
834
932
1230
1270
1370
1420
1420
1420
1420
1420
50Hz
60Hz
60Hz
50
55
60
65
70
75
80
85
95
125
130
140
145
145
145
145
145
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
15
15
15
15
15
15
15
15
15
15
15
17
17
17
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
CA
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering. Brankets contain dimension, model, or mass of type with brakes.
RNFM009–15 RL –CA–5~60
Mass 5.0kg
• Use hex socket head cap screws (M6) for installation.
(RNFM009–15 RL –CA–B–5~60)
(Mass 5.4kg)
8
18
104
3
5
5
4- 6.5
90
38
22
45
96
23.1
18
8
L=300
L=300
104
7
98
186 (226)
96
A
90
A
231 (271)
186 (226)
45
A
A
4- 6.5
7
90
38
15h6
L
90
231 (271)
22
23.1
Fig. 1
98
R
A-A
Mass 5.0kg
(Mass 5.4kg)
• Use hex socket head cap screws (M6) for installation.
L=300
6
22
8
18
104
A
A
6
3.5
104
45
96
23.1
L=300
18
8
186 (226)
96
A
90
A
231 (271)
186 (226)
45
90
231 (271)
22
23.1
RNFM009–17 RL –CA–80~240
(RNFM009–17 RL –CA–B–80~240)
Fig. 2
7
98
4- 6.5
90
38
7
4- 6.5
90
38
98
18h6
L
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
106
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
Solid Shaft
MEMO
Singlephase
90
W
107
15
15W Single-plase Reversible Motor
W
RNFM Series Solid shaft Flange mount type
Output Torque Tout
Output speed n2
r/min
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
50Hz
60Hz
0.371
350
290
0.307
0.038
0.031
0.556
233
193
0.461
0.057
0.047
0.742
175
145
0.615
0.076
0.063
0.890
146
121
0.738
0.091
0.075
1.11
96.7 117
0.922
0.113
0.094
72.5
87.5
1.48
1.23
0.151
0.125
58.0
70.0
1.85
1.54
0.189
0.157
58.3
48.3
2.23
1.84
0.227
0.188
36.3
43.8
2.97
2.46
0.303
0.251
29.0
35.0
3.71
3.07
0.378
0.313
29.2
24.2
4.45
3.69
0.454
0.376
18.1
21.9
5.93
4.92
0.605
0.501
17.5
14.5
7.42
6.15
0.756
0.627
14.6
12.1
8.90
7.38
0.908
0.752
9.06 10.9
11.9
9.83
1.21
1.00
8.75 14.8
7.25
12.3
1.51
1.25
7.29 17.8
6.04
14.8
1.82
1.50
Motor
Speed n1
Allowable Pro
SF
N
4.00
4.00
4.00
4.00
4.00
4.00
4.00
3.53
2.64
2.12
1.76
1.32
1.06
3.34
2.50
2.00
1.67
50Hz
343
343
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
50Hz
35
35
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
343
343
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
50Hz
60Hz
60Hz
35
35
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
0015
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
01
01
01
01
01
01
01
01
01
01
01
01
01
03
03
03
03
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
1
2
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
RNFM0015–01 RL –CC–5~100
• Use hex socket head cap screws (M5) for installation.
Mass 2.7kg
175
175
135
94
80
8
15
4- 5.5
4
4- 5.5
3
32
A
94
4
L
3
32
80
2.5
82
22
A
76
76
A
40
L=300
L=300
80
15
A
135
23.1
23.1
40
8
22
80
Fig. 1
82
R
10h6
A-A
RNFM0015–03 RL –CC–120~240
Mass 2.7kg
• Use hex socket head cap screws (M5) for installation.
175
135
76
76
A
5
5
3
7
38
A
94
94
82
A
15
23.1
8
80
15
A
22
40
L=300
L=300
8
135
40
80
175
22
23.1
Fig. 2
4- 5.5
4- 5.5
80
80
7
38
82
15h6
L
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
108
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
25W Single-plase Reversible Motor
25
Motor
Speed n1
RNFM Series Solid shaft Flange mount type
Allowable Pro
SF
N
2.40
2.40
2.40
2.40
2.40
2.40
2.40
2.12
1.59
1.27
1.06
2.40
2.40
2.00
1.50
1.20
1.00
50Hz
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
1080
1080
50Hz
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
110
110
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
343
343
343
343
343
343
343
343
343
343
343
1080
1080
1080
1080
1080
1080
1450r/min
1750r/min
60Hz
35
35
35
35
35
35
35
35
35
35
35
110
110
110
110
110
110
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
0025
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
01
01
01
01
01
01
01
01
01
01
01
03
03
03
03
03
03
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
160
200
240
3
4
Solid Shaft
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
36.3
43.8
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.06 10.9
7.25
8.75
6.04
7.29
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
0.618
0.512 0.063
0.052
0.927
0.768 0.095
0.078
1.24
1.02
0.126
0.104
1.48
1.23
0.151
0.125
1.85
1.54
0.189
0.157
2.47
2.05
0.252
0.209
3.09
2.56
0.315
0.261
3.71
3.07
0.378
0.313
4.95
4.10
0.504
0.418
6.18
5.12
0.630
0.522
7.42
6.15
0.756
0.627
9.89
8.20
1.01
0.836
12.4
10.2
1.26
1.04
14.8
12.3
1.51
1.25
19.8
16.4
2.02
1.67
24.7
20.5
2.52
2.09
29.7
24.6
3.03
2.51
50Hz
60Hz
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
• Use hex socket head cap screws (M5) for installation.
Mass 2.8kg
175
175
135
94
80
8
15
4- 5.5
4
4- 5.5
3
32
A
94
4
L
3
32
80
2.5
82
22
A
76
76
A
40
L=300
L=300
80
15
A
135
23.1
23.1
40
8
22
Singlephase
RNFM0025–01 RL –CC–5~60
80
Fig. 3
82
R
10h6
A-A
RNFM0025–03 RL –CC–80~240
Mass 2.9kg
• Use hex socket head cap screws (M5) for installation.
175
135
76
76
A
5
5
3
7
38
A
94
94
82
A
15
23.1
8
80
15
A
22
40
L=300
L=300
8
135
40
80
175
22
23.1
Fig. 4
4- 5.5
4- 5.5
80
80
7
38
82
15h6
L
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
109
40
40W Single-plase Reversible Motor
W
RNFM Series Solid shaft Flange mount type
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.12
0.929 0.114
0.095
1.68
1.39
0.171
0.142
2.24
1.86
0.229
0.189
2.69
2.23
0.274
0.227
3.36
2.79
0.343
0.284
4.48
3.72
0.457
0.379
5.61
4.64
0.572
0.474
6.73
5.57
0.686
0.568
8.97
7.43
0.914
0.758
11.2
9.29
1.14
0.947
13.5
11.1
1.37
1.14
17.9
14.9
1.83
1.52
22.4
18.6
2.29
1.89
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
44.8
37.2
4.57
3.79
53.8
44.6
5.49
4.55
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
17.5
14.5
14.6
12.1
9.67 11.7
8.75
7.25
7.29
6.04
Motor
Speed n1
Allowable Pro
SF
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.31
1.05
1.50
1.50
1.20
1.00
1.60
1.20
1.00
N
50Hz
441
490
539
588
588
588
588
588
588
588
1080
1080
1080
1080
1420
1420
1420
50Hz
45
50
55
60
60
60
60
60
60
60
110
110
110
110
145
145
145
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
kgf
60Hz
392
441
490
539
588
588
588
588
588
588
1080
1080
1080
1080
1420
1420
1420
50Hz
60Hz
60Hz
40
45
50
55
60
60
60
60
60
60
110
110
110
110
145
145
145
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
004
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
05
05
05
05
05
05
05
05
05
05
07
07
07
07
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
3
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
RNFM004–05 RL –CC–5~50
• Use hex socket head cap screws (M6) for installation.
Mass 3.0kg
219
219
6
174
L=300
22
45
23.1
174
45
23.1
22
L=300
6
Fig. 1
A
18
90
104
A
82
3
4- 6.5
32
90
2.5
4
104
80
4
80
A
18
90
A
4- 6.5
3
90
32
82
12h6
L
RNFM004–07 RL –CC–60~120
• Use hex socket head cap screws (M6) for installation.
Mass 3.1kg
219
219
6
174
L=300
22
45
23.1
174
45
23.1
22
L=300
6
Fig. 2
R
A-A
A
82
18
104
90
80
3
104
A
5
18
5
80
A
90
A
7
4- 6.5
4- 6.5
7
38
90
90
38
82
15h6
L
R
A-A
RNFM004–17 RL –CC–150~240
• Use hex socket head cap screws (M6) for installation.
Mass 4.3kg
194
8
18
90
22
104
A
A
6
104
3.5
18
6
4- 6.5
90
38
45
23.1
8
7
98
L=300
L=300
90
A
90
A
194
149
149
45
23.1
22
90
Fig. 3
7
4- 6.5
90
38
98
18h6
L
110
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
A-A
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
60W Single-plase Reversible Motor
60
Motor
Speed n1
RNFM Series Solid shaft Flange mount type
Allowable Pro
SF
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.50
1.34
1.07
✻
✻
N
50Hz
539
588
637
686
735
785
834
883
981
1080
1080
1420
1420
1420
1420
1420
1420
kgf
60Hz
490
539
588
637
686
735
785
834
932
1030
1080
1370
1420
1420
1420
1420
1420
50Hz
55
60
65
70
75
80
85
90
100
110
110
145
145
145
145
145
145
60Hz
50
55
60
65
70
75
80
85
95
105
110
140
145
145
145
145
145
1450r/min
1750r/min
W
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
006
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
15
15
15
15
15
15
15
15
15
15
15
17
17
17
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
4
5
Solid Shaft
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
87.5
72.5
58.0
70.0
48.3
58.3
36.3
43.8
29.0
35.0
29.2
24.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
1.68
1.39
0.171
0.142
2.52
2.09
0.257
0.213
3.36
2.79
0.343
0.284
4.04
3.34
0.412
0.341
5.04
4.18
0.514
0.426
6.73
5.57
0.686
0.568
8.41
6.97
0.857
0.710
10.1
8.36
1.03
0.852
13.5
11.1
1.37
1.14
16.8
13.9
1.71
1.42
20.2
16.7
2.06
1.70
26.9
22.3
2.74
2.27
33.6
27.9
3.43
2.84
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
50Hz
60Hz
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
• Use hex socket head cap screws (M6) for installation.
MassA 4.5kg
231
3
38
8
104
4- 6.5
7
98
18
5
22
23.1
96
23.1
104
45
L=300
L=300
18
8
186
96
A
90
A
231
186
45
A
A
5
22
Singlephase
RNFM006–15 RL –CC–5~60
90
Fig. 4
90
4- 6.5
7
90
38
98
15h6
A-A
L
RNFM006–17 RL –CC–80~120
• Use hex socket head cap screws (M6) for installation.
Mass 4.9kg
22
8
18
96
6
104
A
A
6
3.5
23.1
104
45
L=300
L=300
18
8
186
96
A
90
A
231
186
45
90
231
22
23.1
Fig. 5
R
7
98
4- 6.5
90
38
7
4- 6.5
90
38
98
18h6
L
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
111
90
90W Single-plase Reversible Motor
W
RNFM Series Solid shaft Flange mount type
Output speed n2
r/min
50Hz
60Hz
350
290
233
193
175
145
146
121
96.7 117
72.5
87.5
58.0
70.0
58.3
48.3
43.8
36.3
29.0
35.0
24.2
29.2
18.1
21.9
14.5
17.5
12.1
14.6
9.67 11.7
8.75
7.25
7.29
6.04
Output Torque Tout
Nm
kgf m
50Hz
60Hz
50Hz
60Hz
2.09
2.52
0.257
0.213
3.13
3.78
0.386
0.320
4.18
5.04
0.514
0.426
5.02
6.05
0.617
0.511
6.27
7.57
0.772
0.639
8.36
10.1
1.03
0.852
10.4
12.6
1.29
1.07
15.1
12.5
1.54
1.28
20.2
16.7
2.06
1.70
25.2
20.9
2.57
2.13
30.3
25.1
3.09
2.56
40.4
33.4
4.12
3.41
50.4
41.8
5.14
4.26
53.9
50.2
5.50
5.11
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
53.9
53.9
5.50
5.50
Motor
Speed n1
Allowable Pro
SF
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
1.00
✻
✻
✻
✻
N
50Hz
539
588
637
686
735
785
834
883
981
1270
1320
1420
1420
1420
1420
1420
1420
kgf
60Hz
490
539
588
637
686
735
785
834
932
1230
1270
1370
1420
1420
1420
1420
1420
50Hz
55
60
65
70
75
80
85
90
100
130
135
145
145
145
145
145
145
60Hz
50
55
60
65
70
75
80
85
95
125
130
140
145
145
145
145
145
50Hz
60Hz
1450r/min
1750r/min
Outline
Capacity Frame
Reduction
Drawing
Symbol – Size –Suffix – Ratio
Fig.
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
009
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
15
15
15
15
15
15
15
15
15
15
15
17
17
17
17
17
17
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
CC
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
5
7.5
10
12
15
20
25
30
40
50
60
80
100
120
150
200
240
1
2
3. Output torque is limited when SF is ✻. It must be used within the value
stipulated in the table as overload may occur if the motor is loaded to its full
capacity.
Note : 1. Motor slippage may affect n1 and n2.
2. Allowable radial load shows the value when the distance from hollow
shaft end to the point of radial load is 20 mm.
Designate model and voltage and frequency when ordering.
RNFM009–15 RL –CC–5~60
• Use hex socket head cap screws (M6) for installation.
Mass 5.0kg
231
3
38
8
104
4- 6.5
7
98
18
5
22
23.1
96
23.1
104
45
L=300
L=300
18
8
186
96
A
90
A
231
186
45
A
A
5
22
90
Fig. 1
90
4- 6.5
7
90
38
98
15h6
A-A
L
RNFM009–17 RL –CC–80~120
• Use hex socket head cap screws (M6) for installation.
Mass 5.4kg
22
8
18
96
6
104
A
A
6
3.5
23.1
104
45
L=300
L=300
18
8
186
96
A
90
A
231
186
45
90
231
22
23.1
Fig. 2
R
7
98
4- 6.5
90
38
7
4- 6.5
90
38
98
18h6
L
A-A
Note : 1. Output shaft diameter dimensions : Dimension tolerance in
accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in
accordance with JIS B 1301-1996 parallel key (Normal Grade).
112
R
3. Dimentions and Masses in the drawings are subject to change
without notice.
Option
Option
113
15
0.1
W
kW
OPTION Dimension sheet
~
RNFM Series Solid Shaft Flange Mount Type (1) 3-phase Motor
Please refer to page 24-50 for selection table
N
W
O
P
L
L
B
A
Q
P
E
C
E
C
A
Q
K
J
W
A
B
C
E
DM
DM
N
O
R
K
B
A
C
E
V
Dh7
R
B
V
J
Dh7
90
2.2
W
kW
X
X
4–
4–
M
M
S
U
T
L
X
R
dh6
p
p
X
A-A
Fig.1
Reduction
A
B
C
E
J
K
M
D
N
O
V
model
Ratio
0.1kW
32
40
42
50 128 20 6.6 52
33
6
56
5-60
RNFM01– 1120 RL –X1(–B)–Ratio
40
49
57
66 128 28
9
78
37
5
59
40-60
RNFM01– 1220 RL –X1(–B)–Ratio
40
51
65
76 128 13
9
78
42
5
59
80-240
RNFM01– 1230 RL –X1(–B)–Ratio
47
60
79
92 128 11
11
85
46
5
67
80-240
RNFM01– 1330 RL –X1(–B)–Ratio
0.2kW
32
40
42
50 128 20 6.6 52
33
6
56
5-30
RNFM02– 1120 RL –X1(–B)–Ratio
40
49
57
66 128 28
9
78
37
5
59
5-60
RNFM02– 1220 RL –X1(–B)–Ratio
46
58
62
74 128 27.5 11
85
46
5
67
40-60
RNFM02– 1320 RL –X1(–B)–Ratio
47
60
79
92 128 11
11
85
46
5
67
80-240
RNFM02– 1330 RL –X1(–B)–Ratio
54
70
92 108 128 14
14
95
59
5
77
80-240
RNFM02– 1430 RL –X1(–B)–Ratio
0.25kW
40
49
57
66 128 28
9
78
37
5
59
5-30
RNFM03– 1220 RL –X1(–B)–Ratio
46
58
62
74 128 27.5 11
85
46
5
67
40-60
RNFM03– 1320 RL –X1(–B)–Ratio
54
70
92 108 128 14
14
95
59
5
77
80-240
RNFM03– 1430 RL –X1(–B)–Ratio
0.4kW
40
49
57
66 128 28
9
78
37
5
59
5-30
RNFM05– 1220 RL –X1(–B)–Ratio
46
58
62
72 128 27.5 11
85
46
5
67
5-60
RNFM05– 1320 RL –X1(–B)–Ratio
57
70
75
88 128 20
14
95
59
5
77
40-60
RNFM05– 1420 RL –X1(–B)–Ratio
54
70
92 108 128 14
14
95
59
5
77
80-240
RNFM05– 1430 RL –X1(–B)–Ratio
64
84 109 129 128 17
18 110 68
5
90
80-240
RNFM05– 1530 RL –X1(–B)–Ratio
0.55kW
46
58
62
74 138 27.5 11
85
46
5
67
5-30
RNFM08– 1320 RL –X1(–B)–Ratio
57
70
75
88 138 20
14
95
59
5
77
40-60
RNFM08– 1420 RL –X1(–B)–Ratio
64
84 109 129 138 17
18 110 68
5
90
80-240
RNFM08– 1530 RL –X1(–B)–Ratio
0.75kW
46
58
62
74 138 27.5 11
85
46
5
67
5-30
RNFM1– 1320 RL –X1(–B)–Ratio
57
70
75
88 138 20
14
95
59
5
77
5-60
RNFM1– 1420 RL –X1(–B)–Ratio
70
84
80
94 138 28
14 110 68
5
90
40-60
RNFM1– 1520 RL –X1(–B)–Ratio
64
84 109 129 138 17
18 110 68
5
90
80-240
RNFM1– 1530 RL –X1(–B)–Ratio
64
84 109 129 138 17
18 110 68
5
90
80
RNFM1– 1531 RL –X1(–B)–Ratio
1.1kW
57
70
75
88 143 20
14
95
59
5
77
5-30
RNFM1H– 1420 RL –X1(–B)–Ratio
70
84
80
94 143 28
14 110 68
5
90
40-60
RNFM1H– 1520 RL –X1(–B)–Ratio
64
84 109 129 143 17
18 110 68
5
90
80
RNFM1H– 1531 RL –X1(–B)–Ratio
1.5kW
57
70
75
88 143 20
14
95
59
5
77
5-30
RNFM2– 1420 RL –X1(–B)–Ratio
70
84
80
94 143 28
14 110 68
5
90
5-60
RNFM2– 1520 RL –X1(–B)–Ratio
64
84 109 129 143 17
18 110 68
5
90
40-80
RNFM2– 1531 RL –X1(–B)–Ratio
2.2kW
70
84
80
94 150 28
14 110 68
5
90
5-30
RNFM3– 1520 RL –X1(–B)–Ratio
64
84 109 129 150 17
18 110 68
5
90
40-60
RNFM3– 1531 RL –X1(–B)–Ratio
Note: 1. This type is consisit of RNYM type and plug-in shaft.
2. The dimensions of right side shaft type are the same as left side shaft type except for the shaft and safety cover direction.
3. Values in brackets ( ) are for motors with brake.
Power
114
W
20
32
32
32
20
32
32
32
42
32
32
42
32
32
42
42
42
32
42
42
32
42
42
42
42
42
42
42
42
42
42
42
42
0.1
15
kW
W
~
2.2
90
kW
W
L
P
B
E
A
Q
K
K
C
E
DM
DM
A
B
B
A
Dh7
T
4–
U
M
S
4–
Q
N
O
J
W
R
E
C
X
P
A
C
R
V
B
E
C
L
V
N
O
Dh7
L
J
W
X
M
R
X
dh6
p
p
A-A
X
d
18
22
22
28
18
22
28
28
32
22
28
32
22
28
32
32
40
28
32
40
28
32
40
40
40
32
40
40
32
40
40
40
40
P
50
63.5
63.5
71
50
63.5
71
71
91
63.5
71
91
63.5
71
91
91
120
71
91
120
71
91
120
120
120
91
120
120
91
120
120
120
120
Q
28
36
36
42
28
36
42
42
58
36
42
58
36
42
58
58
82
42
58
82
42
58
82
82
82
58
82
82
58
82
82
82
82
Output Shaft
R
S
M6 × 12
6
M6 × 12
6
M6 × 12
6
M8 × 16
7
M6 × 12
6
M6 × 12
6
M8 × 16
7
M8 × 16
7
M8 × 16
8
M6 × 12
6
M8 × 16
7
M8 × 16
8
M6 × 12
6
M8 × 16
7
M8 × 16
8
M8 × 16
8
M10 × 18
8
M8 × 16
7
M8 × 16
8
M10 × 18
8
M8 × 16
7
M8 × 16
8
M10 × 18
8
M10 × 18
8
M10 × 18
8
M8 × 16
8
M10 × 18
8
M10 × 18
8
M8 × 16
8
M10 × 18
8
M10 × 18
8
M10 × 18
8
M10 × 18
8
T
6
6
6
8
6
6
8
8
10
6
8
10
6
8
10
10
12
8
10
12
8
10
12
12
12
10
12
12
10
12
12
12
12
U
3.5
3.5
3.5
4
3.5
3.5
4
4
5
3.5
4
5
3.5
4
5
5
5
4
5
5
4
5
5
5
5
5
5
5
5
5
5
5
5
r
1
1
1
2
1
1
2
2
2
1
2
2
1
2
2
2
3
2
2
3
2
2
3
3
3
2
3
3
2
3
3
3
3
Without brake
J
DM Mass
268 119 6.5 kg
291 119 7.5 kg
292 119 8.0 kg
314 119 10 kg
310 124 7.5 kg
333 124 9.0 kg
361 124 11 kg
356 124 11 kg
384 124 16 kg
353 124 10 kg
381 124 12 kg
404 124 17 kg
353 124 10 kg
381 124 12 kg
412 124 16 kg
404 124 17 kg
437 124 25 kg
423 155 14 kg
474 155 19 kg
498 155 27 kg
423 155 14 kg
474 155 19 kg
498 155 28 kg
498 155 27 kg
498 155 28 kg
504 167 23 kg
534 167 33 kg
528 167 32 kg
504 167 23 kg
534 167 33 kg
528 167 32 kg
553 180 36 kg
548 180 36 kg
J
303
326
327
349
342
365
393
388
416
385
413
436
385
413
444
436
469
466
517
541
466
517
541
541
541
566
596
590
566
596
590
616
611
With brake
DM Mass
124 8.0 kg
124 9.0 kg
124 9.5 kg
124 11 kg
124 9.0 kg
124 10.5 kg
124 12 kg
124 12 kg
124 17 kg
124 12 kg
124 14 kg
124 18 kg
124 12 kg
124 14 kg
124 17 kg
124 18 kg
124 26 kg
155 17 kg
155 21 kg
155 30 kg
155 17 kg
155 21 kg
155 30 kg
155 30 kg
155 30 kg
167 27 kg
167 37 kg
167 36 kg
167 27 kg
167 37 kg
167 36 kg
180 41 kg
180 41 kg
Fig.
1
1
2
2
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
2
1
1
2
1
2
Option
Fig.2
115
15
0.1
W
kW
OPTION Dimension sheet
~
RNFM Series Solid Shaft Flange Mount Type (2) 3-phase Motor
Please refer to page 24-50 for selection table
L
E
C
B
A
R
N
O
J
W
X
X
4–
M
T
S
L
X
M
R
U
4–
Q
A
B
Dh7
V
Dh7
B
A
R
P
E
C
C
E
Q
L
E
C
K
B
A
V
P
O
DM
N
W
DM
J
K
90
2.2
W
kW
p
dh6
p
X
Fig.1
Reduction
model
M
V
D
N
O
K
E
C
J
B
A
Ratio
P1
RNFM01– 1120 RL – Q1
(–B)–Ratio
5-60
56
50 128 20 6.6 60 63.5 3
42
40
0.1kW
32
P1
RNFM01– 1220 RL – Q1
(–B)–Ratio
40-60
9
59
85 82.5 3
66 128 28
57
49
40
P1
RNFM01– 1230 RL – Q1
(–B)–Ratio
80-240
9
59
85 63.5 3
76 128 13
65
51
40
P1
RNFM01– 1330 RL – Q1
(–B)–Ratio
80-240
11
67
94 63.5 3
92 128 11
79
60
47
P1
RNFM02– 1120 RL – Q1
(–B)–Ratio
5-30
56
50 128 20 6.6 60 63.5 3
42
40
32
0.2kW
P1
RNFM02– 1220 RL – Q1
(–B)–Ratio
5-60
9
59
85 82.5 3
66 128 28
57
49
40
P1
RNFM02– 1320 RL – Q1
(–B)–Ratio
40-60
67
94 88.5 3
74 128 27.5 11
62
58
46
P1
RNFM02– 1330 RL – Q1
(–B)–Ratio
80-240
11
67
94 63.5 3
92 128 11
79
60
47
P1
RNFM02– 1430 RL – Q1
(–B)–Ratio
80-240
14 105 82.5 3
77
92 108 128 14
70
54
P1
RNFM03– 1220 RL – Q1
(–B)–Ratio
5-30
9
59
85 82.5 3
57
66 128 28
49
40
0.25kW
P1
RNFM03– 1320 RL – Q1
(–B)–Ratio
40-60
67
94 88.5 3
62
74 128 27.5 11
58
46
P1
RNFM03– 1430 RL – Q1
(–B)–Ratio
80-240
14 105 82.5 3
77
92 108 128 14
70
54
P1
RNFM05– 1220 RL – Q1
(–B)–Ratio
5-30
59
9
85 82.5 3
57
66 128 28
49
40
0.4kW
P1
RNFM05– 1320 RL – Q1
(–B)–Ratio
5-60
67
94 88.5 3
62
74 128 27.5 11
58
46
P1
RNFM05– 1420 RL – Q1
(–B)–Ratio
40-60
77
14 105 95
3
75
88 128 20
70
57
P1
RNFM05– 1430 RL – Q1
(–B)–Ratio
80-240
77
14 105 82.5 3
92 108 128 14
70
54
P1
RNFM05– 1530 RL – Q1
(–B)–Ratio
80-240
90
18 120 95
3
84 109 129 128 17
64
P1
RNFM08– 1320 RL – Q1
(–B)–Ratio
5-30
67
94 88.5 3
62
74 138 27.5 11
58
46
0.55kW
P1
RNFM08– 1420 RL – Q1
(–B)–Ratio
40-60
77
14 105 95
3
75
88 138 20
70
57
P1
RNFM08– 1530 RL – Q1
(–B)–Ratio
80-240
90
18 120 95
3
84 109 129 138 17
64
P1
RNFM1– 1320 RL – Q1
(–B)–Ratio
5-30
67
94 88.5 3
62
74 138 27.5 11
58
46
0.75kW
P1
RNFM1– 1420 RL – Q1
(–B)–Ratio
5-60
77
14 105 95
3
75
88 138 20
70
57
P1
RNFM1– 1520 RL – Q1
(–B)–Ratio
40-60
90
14 120 95
3
80
94 138 28
84
70
P1
RNFM1– 1530 RL – Q1
(–B)–Ratio
80-240
90
18 120 95
3
84 109 129 138 17
64
P1
RNFM1– 1531 RL – Q1
(–B)–Ratio
80
90
18 120 95
3
84 109 129 138 17
64
P1
RNFM1H– 1420 RL – Q1
(–B)–Ratio
5-30
77
14 105 95
3
75
88 143 20
70
57
1.1kW
P1
RNFM1H– 1520 RL – Q1
(–B)–Ratio
40-60
90
3
14 120 95
80
94 143 28
84
70
P1
RNFM1H– 1531 RL – Q1
(–B)–Ratio
80
90
3
18 120 95
84 109 129 143 17
64
P1
RNFM2– 1420 RL – Q1
(–B)–Ratio
5-30
77
3
14 105 95
75
88 143 20
70
57
1.5kW
P1
RNFM2– 1520 RL – Q1
(–B)–Ratio
5-60
90
3
14 120 95
80
84
94 143 28
70
P1
RNFM2– 1531 RL – Q1
(–B)–Ratio
40-80
90
3
18 120 95
84 109 129 143 17
64
P1
RNFM3– 1520 RL – Q1
(–B)–Ratio
5-30
90
3
14 120 95
80
84
94 150 28
70
2.2kW
P1
RNFM3– 1531 RL – Q1
(–B)–Ratio
40-60
90
3
18 120 95
84 109 129 150 17
64
Note: 1. This type is consisit of RNYM type, plug-in shaft and bolt-on flange.
2. The dimensions of right side shaft type are the same as left side shaft type except for the shaft and safety cover direction.
Power
116
W
20
32
32
32
20
32
32
32
42
32
32
42
32
32
42
42
42
32
42
42
32
42
42
42
42
42
42
42
42
42
42
42
42
0.1
15
kW
W
~
2.2
90
kW
W
L
B
A
L
E
C
E
C
J
W
Q
V
A
B
C
E
DM
DM
E
C
V
N
O
R
B
A
R
P
B
A
K
N
P
O
Q
K
J
W
X
X
T
4–
M
U
M
S
4–
L
R
dh6
X
p
p
X
d
18
22
22
28
18
22
28
28
32
22
28
32
22
28
32
32
40
28
32
40
28
32
40
40
40
32
40
40
32
40
40
40
40
P
33
41
41
47
33
41
47
47
63
41
47
63
41
47
63
63
87
47
63
87
47
63
87
87
87
63
87
87
63
87
87
87
87
Q
28
36
36
42
28
36
42
42
58
36
42
58
36
42
58
58
82
42
58
82
42
58
82
82
82
58
82
82
58
82
82
82
82
Output Shaft
R
M6 × 12
M6 × 12
M6 × 12
M8 × 16
M6 × 12
M6 × 12
M8 × 16
M8 × 16
M8 × 16
M6 × 12
M8 × 16
M8 × 16
M6 × 12
M8 × 16
M8 × 16
M8 × 16
M10 × 18
M8 × 16
M8 × 16
M10 × 18
M8 × 16
M8 × 16
M10 × 18
M10 × 18
M10 × 18
M8 × 16
M10 × 18
M10 × 18
M8 × 16
M10 × 18
M10 × 18
M10 × 18
M10 × 18
S
6
6
6
7
6
6
7
7
8
6
7
8
6
7
8
8
8
7
8
8
7
8
8
8
8
8
8
8
8
8
8
8
8
T
6
6
6
8
6
6
8
8
10
6
8
10
6
8
10
10
12
8
10
12
8
10
12
12
12
10
12
12
10
12
12
12
12
U
3.5
3.5
3.5
4
3.5
3.5
4
4
5
3.5
4
5
3.5
4
5
5
5
4
5
5
4
5
5
5
5
5
5
5
5
5
5
5
5
r
1
1
1
2
1
1
2
2
2
1
2
2
1
2
2
2
3
2
2
3
2
2
3
3
3
2
3
3
2
3
3
3
3
Without brake
J
DM Mass
268 119 7.0 kg
291 119 9.0 kg
292 119 9.0 kg
314 119 11 kg
310 124 8.0 kg
333 124 10.5 kg
361 124 12 kg
356 124 12 kg
384 124 18 kg
353 124 12 kg
381 124 14 kg
404 124 19 kg
353 124 12 kg
381 124 14 kg
412 124 18 kg
404 124 19 kg
437 124 29 kg
423 155 16 kg
474 155 21 kg
498 155 31 kg
423 155 16 kg
474 155 21 kg
498 155 30 kg
498 155 31 kg
498 155 32 kg
504 167 25 kg
534 167 35 kg
528 167 36 kg
504 167 25 kg
534 167 35 kg
528 167 36 kg
553 180 38 kg
548 180 40 kg
J
303
326
327
349
342
365
393
388
416
385
413
436
385
413
444
436
469
466
517
541
466
517
541
541
541
566
596
590
566
596
590
616
611
With brake
DM Mass
124 8.5 kg
124 10.5 kg
124 10.5 kg
124 12 kg
124 9.5 kg
124 12 kg
124 14 kg
124 13 kg
124 19 kg
124 14 kg
124 16 kg
124 20 kg
124 14 kg
124 16 kg
124 19 kg
124 20 kg
124 30 kg
155 19 kg
155 23 kg
155 34 kg
155 19 kg
155 23 kg
155 32 kg
155 34 kg
155 34 kg
167 29 kg
167 39 kg
167 40 kg
167 29 kg
167 39 kg
167 40 kg
180 43 kg
180 45 kg
Fig.
1
1
2
2
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
2
1
1
2
1
2
Option
Fig.2
117
15
0.1
W
kW
OPTION Dimension sheet
~
RNHM Series Solid Shaft Foot Mount Type 3-phase Motor
Please refer to page 24-50 for selection table
J
D
J
C
C
Q
Q
L
Q
N
R
R
X
X
R
X
E
R
X
B
A
L
B
B
A
T
U
P
B
S
P
B
G
T
P
O
DM
V
V
Q
C
C
K
J
F
90
2.2
W
kW
H
A
B
M
4–
I
M
M
dh6
R
A-A
X
p
Fig.1
Reduction
A
B
C
D
E
F
G
H
I
J
K
M
model
Ratio
L
0.1kW
83
66
90
40
10
30
70 128 70
10
5-60
RNHM01– 1120 RT –J1(–B)–Ratio 120 10
L
10
40 105 128 82
11
40-60
RNHM01– 1220 RT –J1(–B)–Ratio 136 15 100.5 69 110 51
L
10
40 105 128 97
11
80-240
RNHM01– 1230 RT –J1(–B)–Ratio 144 15 104.5 73 110 51
L
12
47 126 128 101 13
80-240
RNHM01– 1330 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
0.2kW
83
66
90
40
10
30
70 128 70
10
5-30
RNHM02– 1120 RT –J1(–B)–Ratio 120 10
L
10
40 105 128 82
11
5-60
RNHM02– 1220 RT –J1(–B)–Ratio 136 15 100.5 69 110 51
L
12
47 126 128 84.5 13
40-60
RNHM02– 1320 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
12
47 126 128 101 13
80-240
RNHM02– 1330 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
12
51 140 128 118 19
80-240
RNHM02– 1430 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
0.25kW
10
40 105 128 82
11
5-30
RNHM03– 1220 RT –J1(–B)–Ratio 136 15 100.5 69 110 51
L
12
47 126 128 84.5 13
40-60
RNHM03– 1320 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
12
51 140 128 118 19
80-240
RNHM03– 1430 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
0.4kW
10
40 105 128 82
11
5-30
RNHM05– 1220 RT –J1(–B)–Ratio 136 15 100.5 69 110 51
L
12
47 126 128 84.5 13
5-60
RNHM05– 1320 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
12
51 140 128 112 19
40-60
RNHM05– 1420 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
12
51 140 128 118 19
80-240
RNHM05– 1430 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
15
64 173 128 143 20
80-240
RNHM05– 1530 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
0.55kW
12
47 126 138 84.5 13
5-30
RNHM08– 1320 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
12
51 140 138 112 19
40-60
RNHM08– 1420 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
15
64 173 138 143 20
80-240
RNHM08– 1530 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
0.75kW
12
47 126 138 84.5 13
5-30
RNHM1– 1320 RT –J1(–B)–Ratio 164 15 117 78 112 60
L
12
51 140 138 112 19
5-60
RNHM1– 1420 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
15
64 173 138 132 20
40-60
RNHM1– 1520 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
15
64 173 138 143 20
80-240
RNHM1– 1530 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
15
64 173 138 143 20
80
RNHM1– 1531 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
1.1kW
12
51 140 143 112 19
5-30
RNHM1H– 1420 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
15
64 173 143 132 20
40-60
RNHM1H– 1520 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
15
64 173 143 143 20
80
RNHM1H– 1531 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
1.5kW
12
51 140 143 112 19
5-30
RNHM2– 1420 RT –J1(–B)–Ratio 204 20 150 101 132 70
L
15
64 173 143 132 20
5-60
RNHM2– 1520 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
15
64 173 143 143 20
40-80
RNHM2– 1531 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
2.2kW
15
64 173 150 132 20
5-30
RNHM3– 1520 RT –J1(–B)–Ratio 244 20 188 110 160 84
L
15
64 173 150 143 20
40-60
RNHM3– 1531 RT –J1(–B)–Ratio 244 20 188 110 160 84
Note: 1. This type is consisit of RNYM type, plug-in shaft and bolt-on foot.
2. The dimensions of right side shaft type are the same as left side shaft direction except for the shaft and safety cover direction.
There are no safety cover on twin shaft type.
Power
118
0.1
15
kW
W
~
2.2
90
kW
W
J
D
C
C
N
D
O
Q
Q
R
T
B
P
B
A
B
L
P
B
A
P
B
T
U
K
X
E
R
X
X
G
R
S
R
X
DM
V
V
F
Q
L
J
J
C
C
H
A
M
B
4–
I
M
M
dh6
R
A-A
X
p
N
O
V
X
40
51
51
60
40
51
60
60
70
51
60
70
51
60
70
70
84
60
70
84
60
70
84
84
84
70
84
84
70
84
84
84
84
82
96
95
108
82
96
114
108
130
96
114
130
96
114
146
130
157
114
146
157
114
146
178
157
157
146
178
157
146
178
157
178
157
59
59
59
67
59
59
67
67
77
59
67
77
59
67
77
77
90
67
77
90
67
77
90
90
90
77
90
90
77
90
90
90
90
9
9
9
11
9
9
11
11
14
9
11
14
9
11
14
14
18
11
14
18
11
14
18
18
18
14
18
18
14
18
18
18
18
d
18
22
22
28
18
22
28
28
32
22
28
32
22
28
32
32
40
28
32
40
28
32
40
40
40
32
40
40
32
40
40
40
40
P
23
32.5
32.5
35
23
32.5
35
35
48
32.5
35
48
32.5
35
48
48
66
35
48
66
35
48
66
66
66
48
66
66
48
66
66
66
66
Q
28
36
36
42
28
36
42
42
58
36
42
58
36
42
58
58
82
42
58
82
42
58
82
82
82
58
82
82
58
82
82
82
82
Output Shaft
R
M6 × 12
M6 × 12
M6 × 12
M8 × 16
M6 × 12
M6 × 12
M8 × 16
M8 × 16
M8 × 16
M6 × 12
M8 × 16
M8 × 16
M6 × 12
M8 × 16
M8 × 16
M8 × 16
M10 × 18
M8 × 16
M8 × 16
M10 × 18
M8 × 16
M8 × 16
M10 × 18
M10 × 18
M10 × 18
M8 × 16
M10 × 18
M10 × 18
M8 × 16
M10 × 18
M10 × 18
M10 × 18
M10 × 18
S
6
6
6
7
6
6
7
7
8
6
7
8
6
7
8
8
8
7
8
8
7
8
8
8
8
8
8
8
8
8
8
8
8
T
6
6
6
8
6
6
8
8
10
6
8
10
6
8
10
10
12
8
10
12
8
10
12
12
12
10
12
12
10
12
12
12
12
U
3.5
3.5
3.5
4
3.5
3.5
4
4
5
3.5
4
5
3.5
4
5
5
5
4
5
5
4
5
5
5
5
5
5
5
5
5
5
5
5
r
1
1
1
2
1
1
2
2
2
1
2
2
1
2
2
2
3
2
2
3
2
2
3
3
3
2
3
3
2
3
3
3
3
Without brake
J
DM Mass
268 119 6.5kg
293 119 7.5kg
292 119 8.0kg
314 119 10 kg
310 124 7.5kg
335 124 9.0kg
363 124 11 kg
356 124 11 kg
384 124 16 kg
355 124 10 kg
383 124 12 kg
404 124 17 kg
355 124 10 kg
383 124 12 kg
412 124 16 kg
404 124 17 kg
437 124 25 kg
425 155 14 kg
474 155 19 kg
498 155 27 kg
425 155 14 kg
474 155 19 kg
498 155 28 kg
498 155 27 kg
498 155 28 kg
504 167 23 kg
534 167 33 kg
528 167 32 kg
504 167 23 kg
534 167 33 kg
528 167 32 kg
553 180 36 kg
548 180 36 kg
J
303
328
327
349
342
367
395
388
416
387
415
436
387
415
444
436
469
468
517
541
468
517
541
541
541
566
596
590
566
596
590
616
611
With brake
DM Mass
124 8.0 kg
124 9.0 kg
124 9.5 kg
124 11 kg
124 9.0 kg
124 10.5 kg
124 12 kg
124 12 kg
124 17 kg
124 12 kg
124 14 kg
124 18 kg
124 12 kg
124 14 kg
124 17 kg
124 18 kg
124 26 kg
155 17 kg
155 21 kg
155 30 kg
155 17 kg
155 21 kg
155 30 kg
155 30 kg
155 30 kg
167 27 kg
167 37 kg
167 36 kg
167 27 kg
167 37 kg
167 36 kg
180 41 kg
180 41 kg
Fig.
1
1
2
2
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
2
1
1
1
2
2
1
1
2
1
1
2
1
2
Option
Fig.2
119
15
0.1
W
kW
OPTION Dimension sheet
~
IEC Flange Type
90
2.2
W
kW
Please refer to page 24-50 for selection table and other dimensions
K
I
L
Z1–
s1
G
F
V
X
U
a
b
T
A
E
B
s
Q
a
m
d1k6
a-a
F
C
b–
Fig.1
Power
0.1kW
0.2kW
0.25kW
0.4kW
0.55kW
0.75kW
1.1kW
1.5kW
2.2kW
120
Reduction
Ratio
5~60
80~240
5~30
40~60
80~240
5~30
40~60
80~120
150~240
5~30
40~60
80~120
150~240
5~30
40~60
80~120
150~240
5~30
40~60
80~120
150~240
5~30
40~60
80
5~30
40~60
80
5~30
40~60
model
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
RNYJ
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
1120
1230
1120
1220
1330
1220
1320
1430
1430
1220
1320
1430
1430
1320
1420
1530
1530
1320
1420
1530
1530
1420
1520
1531
1420
1520
1531
1520
1531
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
–
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Ratio
Motor Flange
Size
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
71/A160
80/A200
80/A200
80/A200
80/A200
80/A200
80/A200
80/A200
80/A200
90/A200
80/A200
90/A200
90/A200
80/A200
90/A200
100/A250
100/A250
A
B
Q
E
Z
S
C1
F1
I
D
160
160
160
160
160
160
160
160
160
160
160
160
160
200
200
200
200
200
200
200
200
200
200
200
200
200
200
250
250
110H8
110H8
110H8
110H8
110H8
110H8
110H8
110H8
110H8
110H8
110H8
110H8
110H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
130H8
180H8
180H8
65
65
65
65
65
65
90
90
90
65
90
90
90
90
90
90
90
90
90
90
90
90
110
110
90
110
110
150
150
130
130
130
130
130
130
130
130
130
130
130
130
130
165
165
165
165
165
165
165
165
165
165
165
165
165
165
215
215
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
4
9
9
9
9
9
9
9
9
9
9
9
9
9
12
12
12
12
12
12
12
12
12
11
11
12
11
11
14
14
11
11
11
11
11
11
10
10
10
11
10
10
10
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12.5
12
12
12.5
12
12
15
15
4.5
4.5
4.5
4.5
4.5
4.5
5
5
5
4.5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
5
6
6
35
35
35
35
35
35
33
33
33
35
33
33
33
43
43
43
43
43
43
43
43
43
53
53
43
53
53
63
63
12k6
12k6
12k6
12k6
12k6
12k6
14k6
14k6
14k6
12k6
14k6
14k6
14k6
14k6
14k6
14k6
14k6
14k6
14k6
14k6
14k6
14k6
19k6
19k6
14k6
19k6
19k6
19k6
19k6
0.1
15
kW
W
~
L
U
T
V
s1
m1
G
F
X
K
Mass
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
25
35
35
25
35
35
35
35
4
4
4
4
4
4
5
5
5
4
5
5
5
5
5
5
5
5
5
5
5
5
6
6
5
6
6
6
6
13.5
13.5
13.5
13.5
13.5
13.5
16
16
16
13.5
16
16
16
16
16
16
16
16
16
16
16
16
21.5
21.5
16
21.5
21.5
21.5
21.5
18
18
18
18
18
18
16
16
16
18
16
16
16
16
16
16
16
16
16
16
16
16
25
25
16
25
25
25
25
M4
M4
M4
M4
M4
M4
M5
M5
M5
M4
M5
M5
M5
M5
M5
M5
M5
M5
M5
M5
M5
M5
M6
M6
M5
M6
M6
M6
M6
8
8
8
8
8
8
10
10
10
8
10
10
10
10
10
10
10
10
10
10
10
10
12
12
10
12
12
12
12
110
110
110
110
110
110
150
150
150
110
150
150
150
150
150
150
150
150
150
150
150
150
200
200
150
200
200
200
200
90
90
90
90
90
90
112
112
112
90
112
112
112
112
116
116
116
112
116
116
116
116
150
116
116
150
116
150
116
–
–
–
–
–
–
115
115
115
–
115
115
115
115
115
115
115
115
115
115
115
115
130
130
115
130
130
130
130
227
251
227
260
283
260
302
325
326
260
302
325
326
302
338
363
370
302
338
363
370
347
421
388
347
421
388
421
388
6.2 kg
7.7 kg
6.2 kg
7.7 kg
9.4 kg
7.7 kg
12.6 kg
16.8 kg
16.8 kg
7.7 kg
12.6 kg
16.8 kg
16.8 kg
13.3 kg
16.5 kg
23.5 kg
23.5 kg
13.3 kg
16.5 kg
23.5 kg
23.5 kg
16.5 kg
31.6 kg
26.6 kg
16.5 kg
31.6 kg
26.6 kg
33.5 kg
31.5 kg
Option
2.2
90
kW
W
121
90
W
122
MEMO
Water proof type
IP65
IP65
Water proof type IP65
123
135
IEC Standard IP65 Water proof/dust proof.
It is ideal for places exposed to water
splashes or places that are washed
periodically.
IP65: The IP indication that represents dust-proofing and water-proofing grades is prescribed by IEC529 and
IEC34-5. "6" of IP65 represents a "perfect dust-proofing structure" that is the highest-grade protection from
contact or entry of solids, while "5" represents protection from water, ensuring protection from water jets in
all directions.
The motor has a structure that permits motor operation without any trouble even if it is exposed to water
jets in all directions from a nozzle.
Test conditions: A nozzle of 6.3 mm in I.D. is placed at a distance of 3 m from the test piece and water jetted out of the
nozzle under pressure of 30 kPa at the flow rate of 12.5 l/min is directed at the test piece in all directions
for three minutes. After that, there should be no abnormality. The motor cannot be used underwater or in
places exposed to high-pressure water jets.
Hollow shaft type
Cabtyre cable
7.7×2m
Steinless steel shaft
bolts
Steinless steel
Cabtyre cable
7.7×2m
Solid shaft type
Steinless steel shaft
(Shaft direction L)
Steinless steel shaft
Cabtyre cable
7.7×2m
(Shaft direction R)
124
15~90W 3-phase Motor Water Proof Type (IP65)
15
W
~
RNYM Series Hollow Shaft Type
90
W
Dimensions of waterproof types (IP65) are as below.
Please refer to page 18–22 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
Cabtyre cable
7.7✕2m
X
L
N
M
Z
G
K
F
A
J
E
B
B
P
P
4- d
I
C
Without brake
t
D1
b
R
W
W
D
U
A-A
L
Cabtyre cable
7.7✕2m
X
N
M
G
K
F
A
J
E
IP65
B
P
P
I
Z
B
C
4- d
With brake
3-phase motor
Motor Power
15W
25W
40W
60W
90W
Motor Power
15W
25W
40W
60W
90W
Model
RNYM0015-03(-B)-5~240
RNYM0025-03(-B)-5~240
RNYM004-07(-B)-5~120
RNYM004-17(-B)-150~240
RNYM006-07(-B)-5~60
RNYM006-17(-B)-80~240
RNYM009-17(-B)-5~240
Model
RNYM0015-03(-B)-5~240
RNYM0025-03(-B)-5~240
RNYM004-07(-B)-5~120
RNYM004-17(-B)-150~240
RNYM006-07(-B)-5~60
RNYM006-17(-B)-80~240
RNYM009-17(-B)-5~240
A
C
E
F
G
I
J
K
M
P
Z
d
80
80
90
90
90
90
90
76
76
76
90
76
90
90
8
8
6
8
6
8
8
15
15
18
18
18
18
18
94
94
104
104
104
104
104
82
82
82
98
82
98
98
78
78
78
86
78
86
86
23
23
23
23
23
23
23
40
40
45
45
45
45
45
2
2
2
2
2
2
2
38
38
38
45
38
45
45
5.5
5.5
6.5
6.5
6.5
6.5
6.5
D
15H8
15H8
15H8
15H8
15H8
15H8
15H8
b
5
5
5
5
5
5
5
Output Hollow Shaft
t
D1
U
17.3 15.6
78
17.3 15.6
78
17.3 15.6
78
17.3 15.6
94
17.3 15.6
78
17.3 15.6
94
17.3 15.6
94
W
28
28
28
28
28
28
28
R
1
1
1
1
1
1
1
Without Brake
With Brake
Mass
L
N
X
L
N
X
(kg)
189
141
29
212
172
6
2.8(3.1)
189
141
29
212
172
6
2.9(3.2)
194
141
29
217
172
6
3.1(3.4)
229
176
29
255
210
3
4.7(5.1)
194
141
29
217
172
6
3.1(3.4)
229
176
29
255
210
3
4.7(5.1)
229
176
29
255
210
3
4.7(5.1)
Values in bracket ( ) are for motors with brake.
Note : 1. Output shaft diameter dimensions : Dimension tolerance in accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and Masses in the drawings are subject to change without notice.
125
15
W
~
40
W
15~40W Single-phase Motor Water Proof Type (IP65)
RNYM Series Hollow Shaft Type
Dimensions of waterproof types (IP65) are as below.
Please refer to page 56–60 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
Cabtyre cable
7.7✕2m
X
L
N
M
Z
G
K
F
A
J
E
B
B
P
P
4- d
I
C
Without brake
t
D1
b
R
W
W
D
U
A-A
L
Cabtyre cable
7.7✕2m
X
N
M
G
K
F
A
J
E
B
P
P
I
Z
B
C
4- d
With brake
Single-phase motor
Motor Power
15W
25W
40W
Motor Power
15W
25W
40W
Model
RNYM0015-03-CA(-B)-5~240
RNYM0025-03-CA(-B)-5~240
RNYM004-17-CA(-B)-5~240
Model
RNYM0015-03-CA(-B)-5~240
RNYM0025-03-CA(-B)-5~240
RNYM004-17-CA(-B)-5~240
A
C
E
F
G
I
J
K
M
P
Z
d
80
80
90
76
76
90
8
8
8
15
15
18
94
94
104
82
82
98
78
78
86
23
23
23
40
40
45
2
2
2
38
38
45
5.5
5.5
6.5
D
15H8
15H8
15H8
b
5
5
5
Output Hollow Shaft
t
D1
U
17.3 15.6
78
17.3 15.6
78
17.3 15.6
94
W
28
28
28
R
1
1
1
Without Brake
With Brake
Mass
L
N
X
L
N
X
(kg)
189
141
29
212
172
6
2.8(3.1)
189
141
29
212
172
6
2.9(3.2)
229
176
29
255
210
3
4.7(5.1)
Values in bracket ( ) are for motors with brake.
Note : 1. Output shaft diameter dimensions : Dimension tolerance in accordance with JIS B 0401-1976 "H8".
2. Output shaft keyway dimensions : Dimension torerance in accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and Masses in the drawings are subject to change without notice.
126
15~90W 3-phase Motor Water Proof Type (IP65)
15
W
~
RNFM Series Solid Shaft Flange Mount Type Shaft Direction L
90
W
Dimensions of waterproof types (IP65) are as below.
Please refer to page 88–92 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
L
Cabtyre cable
7.7✕2m
X
M
N
L1
E
b
K
A
R
F
t
h
J
B
G
D
B
H
I
Z
B-B
P
Q
C
4- d
L
Without brake
L
M
X
Cabtyre cable
7.7✕2m
N
L2
E
b
K
F
R
A
t
h
J
B
Z
G
D
B
B-B
H
I
P
Q
C
4- d
L
3-phase motor
Motor Power
15W
25W
40W
60W
90W
Motor Power
15W
25W
40W
60W
90W
Model
RNFM0015-01L(-B)-5~100
RNFM0015-03L(-B)-120~240
RNFM0025-01L(-B)-5~60
RNFM0025-03L(-B)-80~240
RNFM004-05L(-B)-5~50
RNFM004-07L(-B)-60~120
RNFM004-17L(-B)-150~240
RNFM006-07L(-B)-5~60
RNFM006-17L(-B)-80~240
RNFM009-15L(-B)-5~60
RNFM009-17L(-B)-80~240
Model
RNFM0015-01L(-B)-5~100
RNFM0015-03L(-B)-120~240
RNFM0025-01L(-B)-5~60
RNFM0025-03L(-B)-80~240
RNFM004-05L(-B)-5~50
RNFM004-07L(-B)-60~120
RNFM004-17L(-B)-150~240
RNFM006-07L(-B)-5~60
RNFM006-17L(-B)-80~240
RNFM009-15L(-B)-5~60
RNFM009-17L(-B)-80~240
A
C
E
F
G
H
I
J
K
M
P
Q
Z
d
80
80
80
80
90
90
90
90
90
90
90
76
76
76
76
76
76
90
76
90
90
90
8
8
8
8
6
6
8
6
8
8
8
15
15
15
15
18
18
18
18
18
18
18
94
94
94
94
104
104
104
104
104
104
104
41
41
41
41
41
41
49
41
49
49
49
82
82
82
82
82
82
98
82
98
98
98
78
78
78
78
78
78
86
78
86
86
86
23
23
23
23
23
23
23
23
23
23
23
40
40
40
40
45
45
45
45
45
45
45
3
7
3
7
3
7
7
7
7
7
7
32
38
32
38
32
38
38
38
38
38
38
38
38
38
38
38
38
45
38
45
45
45
5.5
5.5
5.5
5.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
D
10h6
15h6
10h6
15h6
12h6
15h6
18h6
15h6
18h6
15h6
18h6
b
4
5
4
5
4
5
6
5
6
6
6
Output Hollow Shaft
t
h
2.5
4
3
5
2.5
4
3
5
2.5
4
3
5
3.5
6
3
5
3.5
6
3.5
6
3.5
6
R
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
L1
22
22
22
22
22
22
22
22
22
22
22
Without Brake
L
N
X
189
141
29
189
141
29
189
141
29
189
141
29
194
141
29
194
141
29
229
176
29
194
141
29
229
176
29
229
176
29
229
176
29
L
212
212
212
212
217
217
255
217
255
255
255
With Brake
N
172
172
172
172
172
172
210
172
210
210
210
X
6
6
6
6
6
6
3
6
3
3
3
IP65
With brake
Mass
(kg)
2.9(3.2)
2.9(3.2)
3.0(3.3)
3.1(3.4)
3.2(3.5)
3.3(3.6)
4.8(5.2)
3.3(3.6)
4.8(5.2)
4.8(5.2)
4.8(5.2)
Values in bracket ( ) are for motors with brake.
Note : 1. Output shaft diameter dimensions : Dimension tolerance in accordance with JIS B 0401-1976 "h6".
2. Output shaft keyway dimensions : Dimension torerance in accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and Masses in the drawings are subject to change without notice.
127
15
W
~
90
W
15~90W 3-phase Motor Water Proof Type (IP65)
RNFM Series Solid Shaft Flange Mount Type Shaft Direction R
Dimensions of waterproof types (IP65) are as below.
Please refer to page 88–92 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
Cabtyre cable
7.7✕2m
X
L
M
N
E
L1
J
B
Z
F
R
A
G
t
K
h
b
B
D
B-B
C
Cabtyre cable
7.7✕2m
H
P
4- d
I
Q
R
Without brake
L
X
N
M
E
L1
J
B
R
A
F
K
h
b
Z
G
t
B
D
B-B
C
P
4- d
H
I
Q
R
With brake
3-phase motor
Motor Power
15W
25W
40W
60W
90W
Motor Power
15W
25W
40W
60W
90W
Model
RNFM0015-01R(-B)-5~100
RNFM0015-03R(-B)-120~240
RNFM0025-01R(-B)-5~60
RNFM0025-03R(-B)-80~240
RNFM004-05R(-B)-5~50
RNFM004-07R(-B)-60~120
RNFM004-17R(-B)-150~240
RNFM006-07R(-B)-5~60
RNFM006-17R(-B)-80~240
RNFM009-15R(-B)-5~60
RNFM009-17R(-B)-80~240
Model
RNFM0015-01R(-B)-5~100
RNFM0015-03R(-B)-120~240
RNFM0025-01R(-B)-5~60
RNFM0025-03R(-B)-80~240
RNFM004-05R(-B)-5~50
RNFM004-07R(-B)-60~120
RNFM004-17R(-B)-150~240
RNFM006-07R(-B)-5~60
RNFM006-17R(-B)-80~240
RNFM009-15R(-B)-5~60
RNFM009-17R(-B)-80~240
A
C
E
F
G
H
I
J
K
M
P
Q
Z
d
80
80
80
80
90
90
90
90
90
90
90
76
76
76
76
76
76
90
76
90
90
90
8
8
8
8
6
6
8
6
8
8
8
15
15
15
15
18
18
18
18
18
18
18
94
94
94
94
104
104
104
104
104
104
104
41
41
41
41
41
41
49
41
49
49
49
82
82
82
82
82
82
98
82
98
98
98
78
78
78
78
78
78
86
78
86
86
86
23
23
23
23
23
23
23
23
23
23
23
40
40
40
40
45
45
45
45
45
45
45
3
7
3
7
3
7
7
7
7
7
7
32
38
32
38
32
38
38
38
38
38
38
38
38
38
38
38
38
45
38
45
45
45
5.5
5.5
5.5
5.5
6.5
6.5
6.5
6.5
6.5
6.5
6.5
D
10h6
15h6
10h6
15h6
12h6
15h6
18h6
15h6
18h6
15h6
18h6
b
4
5
4
5
4
5
6
5
6
6
6
Output Hollow Shaft
t
h
2.5
4
3
5
2.5
4
3
5
2.5
4
3
5
3.5
6
3
5
3.5
6
3.5
6
3.5
6
R
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
L1
22
22
22
22
22
22
22
22
22
22
22
Without Brake
With Brake
Mass
L
N
X
L
N
X
(kg)
189
141
29
212
172
6
2.9(3.2)
189
141
29
212
172
6
2.9(3.2)
189
141
29
212
172
6
3.0(3.3)
189
141
29
212
172
6
3.1(3.4)
194
141
29
217
172
6
3.2(3.5)
194
141
29
217
172
6
3.3(3.6)
229
176
29
255
210
3
4.8(5.2)
194
141
29
217
172
6
3.3(3.6)
229
176
29
255
210
3
4.8(5.2)
229
176
29
255
210
3
4.8(5.2)
229
176
29
255
210
3
4.8(5.2)
Values in bracket ( ) are for motors with brake.
Note : 1. Output shaft diameter dimensions : Dimension tolerance in accordance with JIS B 0401-1976 "h6".
2. Output shaft keyway dimensions : Dimension torerance in accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and Masses in the drawings are subject to change without notice.
128
15~40W Single-phase Motor Water Proof Type (IP65)
15
W
~
RNFM Series Solid Shaft Flange Mount Type Shaft Direction L
40
90
W
Dimensions of waterproof types (IP65) are as below.
Please refer to page 94–96 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
L
Cabtyre cable
7.7✕2m
X
M
N
L1
E
b
K
A
R
F
t
h
J
B
G
D
B
H
I
Z
B-B
P
Q
C
4- d
L
Without brake
L
M
X
Cabtyre cable
7.7✕2m
N
L2
E
b
K
F
R
A
t
h
J
B
Z
G
D
B
B-B
H
I
P
Q
C
4- d
L
Motor Power
15W
25W
40W
Motor Power
15W
25W
40W
Model
RNFM0015-01L-CA(-B)-5~100
RNFM0015-03L-CA(-B)-120~240
RNFM0025-01L-CA(-B)-5~60
RNFM0025-03L-CA(-B)-80~240
RNFM004-17L-CA(-B)-80~240
Model
RNFM0015-01L-CA(-B)-5~100
RNFM0015-03L-CA(-B)-120~240
RNFM0025-01L-CA(-B)-5~60
RNFM0025-03L-CA(-B)-80~240
RNFM004-17L-CA(-B)-80~240
A
C
E
F
G
H
I
J
K
M
P
Q
Z
d
80
80
80
80
90
76
76
76
76
90
8
8
8
8
8
15
15
15
15
18
94
94
94
94
104
41
41
41
41
49
82
82
82
82
98
78
78
78
78
86
23
23
23
23
23
40
40
40
40
45
3
7
3
7
7
32
32
32
32
38
38
38
38
38
45
5.5
5.5
5.5
5.5
6.5
D
10h6
15h6
10h6
15h6
18h6
b
4
4
4
4
6
Output Hollow Shaft
t
h
2.5
4
2.5
4
2.5
4
2.5
4
3.5
6
R
0.4
0.4
0.4
0.4
0.4
L1
22
22
22
22
22
IP65
With brake
Single-phase motor
Without Brake
With Brake
Mass
(kg)
L
N
X
L
N
X
189
141
29
212
172
6
2.9(3.2)
189
141
29
212
172
6
2.9(3.2)
189
141
29
212
172
6
3.0(3.3)
189
141
29
212
172
6
3.1(3.4)
229
176
29
255
210
3
4.8(5.2)
Values in bracket ( ) are for motors with brake.
Note : 1. Output shaft diameter dimensions : Dimension tolerance in accordance with JIS B 0401-1976 "h6".
2. Output shaft keyway dimensions : Dimension torerance in accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and Masses in the drawings are subject to change without notice.
129
15
W
~
40
90
W
15~40W Single-phase Motor Water Proof Type (IP65)
RNFM Series Solid Shaft Flange Mount Type Shaft Direction R
Dimensions of waterproof types (IP65) are as below.
Please refer to page 94–96 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
Cabtyre cable
7.7✕2m
X
L
M
N
E
L1
J
B
Z
F
R
A
G
t
K
h
b
B
D
B-B
C
Cabtyre cable
7.7✕2m
H
P
4- d
I
Q
R
Without brake
L
X
N
M
E
L1
J
B
R
A
F
K
h
b
Z
G
t
B
D
B-B
C
P
4- d
H
I
Q
R
With brake
Single-phase motor
Motor Power
15W
25W
40W
Motor Power
15W
25W
40W
Model
RNFM0015-01R-CA(-B)-5~100
RNFM0015-03R-CA(-B)-120~240
RNFM0025-01R-CA(-B)-5~60
RNFM0025-03R-CA-(-B)-80~240
RNFM004-17R-CA-(-B)-80~240
Model
RNFM0015-01R-CA(-B)-5~100
RNFM0015-03R-CA(-B)-120~240
RNFM0025-01R-CA(-B)-5~60
RNFM0025-03R-CA(-B)-80~240
RNFM004-17R-CA(-B)-80~240
A
C
E
F
G
H
I
J
K
M
P
Q
Z
d
80
80
80
80
90
76
76
76
76
90
8
8
8
8
8
15
15
15
15
18
94
94
94
94
104
41
41
41
41
49
82
82
82
82
98
78
78
78
78
86
23
23
23
23
23
40
40
40
40
45
3
7
3
7
7
32
32
32
32
38
38
38
38
38
45
5.5
5.5
5.5
5.5
6.5
D
10h6
15h6
10h6
15h6
18h6
b
4
4
4
4
6
Output Hollow Shaft
t
h
2.5
4
2.5
4
2.5
4
2.5
4
3.5
6
R
0.4
0.4
0.4
0.4
0.4
L1
22
22
22
22
22
Without Brake
With Brake
Mass
(kg)
L
N
X
L
N
X
189
141
29
212
172
6
2.9(3.2)
189
141
29
212
172
6
2.9(3.2)
189
141
29
212
172
6
3.0(3.3)
189
141
29
212
172
6
3.1(3.4)
229
176
29
255
210
3
4.8(5.2)
Values in bracket ( ) are for motors with brake.
Note : 1. Output shaft diameter dimensions : Dimension tolerance in accordance with JIS B 0401-1976 "h6".
2. Output shaft keyway dimensions : Dimension torerance in accordance with JIS B 1301-1996 parallel key (Normal Grade).
3. Dimensions and Masses in the drawings are subject to change without notice.
130
0.1~2.2kW 3-phase Motor Water Proof Type (IP65)
0.1
kW
~
RNYM Series Hollow Shaft Type
Motors without brake ore available for the water proof type of 0.1kW or more. Dimensions of waterproof
types (IP65) are as below.
Please refer to page 24–51 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
2.2
kW
L
Motor Power
J
0.1kW
Fig. 1
0.1kW Without brake
L
J
0.2kW
Fig. 2
0.2~0.4kW Without brake
L
J
0.25kW
Fig. 3 0.1kW Without brake
0.4kW
L
258
303
326
327
349
377
419
286
321
344
372
367
395
437
481
322
364
392
415
501
322
364
392
423
415
448
501
559
J
149
149
149
149
149
147
147
149
149
149
149
149
149
147
147
149
149
149
149
147
149
149
149
149
149
149
147
147
Mass(kg)
5.5
7.0
7.5
8.5
10
11
15.5
6.5
8.0
9.5
11
10
16
16.5
24.5
9.5
10.5
12
17
27
9.5
10.5
12
16
17
24
27
64
Fig.
1
1
1
3
3
3
3
2
2
2
2
4
4
4
4
2
2
2
4
4
2
2
2
2
4
4
4
4
Model
RNYM08-1310-5~10
RNYM08-1320-7~30
RNYM08-1420-40~60
RNYM08-1530-80~240
RNYM08-1640-300~1440
RNYM1-1310-5~10
RNYM1-1320-7~30
RNYM1-1420-5~60
RNYM1-1520-40~60
RNYM1-1530-80~240
RNYM1-1531-80
RNYM1-1631-150~240
RNYM1-1640-300~1440
RNYM1H-1410-5~10
RNYM1H-1420-7~30
RNYM1H-1520-40~60
RNYM1H-1531-80
RNYM1H-1630-100~120
RNYM1H-1631-150~240
RNYM2-1410-5~10
RNYM2-1420-7~30
RNYM2-1520-5~60
RNYM2-1531-40~80
RNYM2-1630-80~120
RNYM2-1631-150~240
RNYM3-1510-5~10
RNYM3-1520-7~30
RNYM3-1531-40~80
RNYM3-1630-80~120
RNYM3-1631-150~240
L
J
153
153
153
153
152
153
153
153
153
153
153
152
152
158
158
158
158
158
158
158
158
158
158
158
158
165
165
165
164
164
Mass(kg)
12.5
14
18
25
68
13.5
14
18
27
26
27
47
69
20.5
22
30
30
53
54
22.5
22
32
31
53
54
29.5
35
35
58
58
Fig.
5
5
5
6
6
5
5
5
5
6
6
6
6
5
5
5
6
6
6
5
5
5
6
6
6
5
5
6
6
6
J
L
Model
RNYM01-1010-5~10
RNYM01-1120-7~60
RNYM01-1220-40~60
RNYM01-1230-80~240
RNYM01-1330-80~240
RNYM01-1340-300~1440
RNYM01-1440-300~1440
RNYM02-1110-5~10
RNYM02-1120-7~30
RNYM02-1220-5~60
RNYM02-1320-40~60
RNYM02-1330-80~240
RNYM02-1430-80~240
RNYM02-1440-300~1440
RNYM02-1540-300~1440
RNYM03-1210-5~10
RNYM03-1220-7~30
RNYM03-1320-40~60
RNYM03-1430-80~240
RNYM03-1540-300~1440
RNYM05-1210-5~10
RNYM05-1220-7~30
RNYM05-1320-5~60
RNYM05-1420-40~60
RNYM05-1430-80~240
RNYM05-1530-80~240
RNYM05-1540-300~1440
RNYM05-1640-300~1440
IP65
0.1~0.4kW
Fig. 4
0.2~0.4kW Without brake
0.55~2.2kW
Motor Power
J
0.55kW
Fig. 5
0.55~2.2kW Without brake
J
0.75kW
Fig. 6
0.55~2.2kW Without brake
1.1kW
1.5kW
2.2kW
604
558
604
593
605
593
605
624
624
131
0.1
kW
~
2.2
90
kW
W
0.1~1.5kW Motor for inverter Water Proof Type (IP65)
RNYM Series Hollow Shaft Type
Motors without brake ore available for the water proof type of 0.1kW or more. Dimensions of waterproof
types (IP65) are as below.
Please refer to page 74–83 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is waterproof (IP65) when ordering or
inquiring.
0.1~0.2kW
L
J
J
L
Fig. 1
0.1~0.2kW Without brake
Fig. 2
Motor Power
0.1kW
0.2kW
0.1~0.2kW Without brake
Model
RNYM01-1110-AV-5~10
RNYM01-1120-AV-7~30
RNYM01-1220-AV-5~60
RNYM01-1320-AV-40~60
RNYM01-1330-AV-80~240
RNYM01-1430-AV-80~240
RNYM02-1440-AV-300~1440
RNYM02-1540-AV-300~1440
RNYM02-1210-AV-5~10
RNYM02-1220-AV-7~30
RNYM02-1320-AV-5~60
RNYM02-1420-AV-40~60
RNYM02-1430-AV-80~240
RNYM02-1530-AV-80~240
RNYM05-1540-AV-300~1440
RNYM05-1640-AV-300~1440
L
286
321
344
372
367
395
437
481
322
364
392
423
415
448
501
559
J
149
149
149
149
149
149
147
147
149
149
149
149
149
149
147
147
Mass(kg)
6.5
8.0
9.5
11
10
16
16.5
24.5
9.5
10.5
12
16
17
24
27
64
Fig.
1
1
1
1
2
2
2
2
1
1
1
1
2
2
2
2
J
153
153
153
153
153
153
152
152
158
158
158
158
158
158
165
165
165
164
164
Mass(kg)
13.5
14
18
27
26
27
47
69
22.5
22
32
31
53
54
29.5
35
35
58
58
Fig.
3
3
3
3
4
4
4
4
3
3
3
4
4
4
3
3
4
4
4
J
J
0.4~1.5kW
Fig. 3
0.4~1.5kW Without brake
Motor Power
0.4kW
0.75kW
1.5kW
132
Fig. 4
0.4~1.5kW Without brake
Model
RNYM05-1310-AV-5~10
RNYM05-1320-AV-7~30
RNYM05-1420-AV-5~60
RNYM05-1520-AV-40~60
RNYM05-1530-AV-80~240
RNYM05-1531-AV-80
RNYM1-1631-AV-150~240
RNYM1-1640-AV-300~1440
RNYM1-1410-AV-5~10
RNYM1-1420-AV-7~30
RNYM1-1520-AV-5~60
RNYM1-1531-AV-40~80
RNYM2-1630-AV-80~120
RNYM2-1631-AV-150~240
RNYM2-1510-AV-5~10
RNYM2-1520-AV-7~30
RNYM2-1531-AV-40~80
RNYM3-1630-AV-80~120
RNYM3-1631-AV-150~240
L
558
604
593
605
624
624
IP65
eG3
Increased safety type eG3
133
125
0.1
kW
~
0.4
90
kW
W
0.1~0.4kW 3-phase Motor Increased Safety Type (eG3)
RNYM Series Hollow Shaft Type
Motors without brake are available for the Increased safety type. Dimensions of Increased safety types
(eG3) are as below.
Please refer to page 24–37 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is Increased safety (eG3) when ordering
or inquiring.
Increased safety motors conform to eG3 of Japanese Industrial Standards (JIS).
0.1~0.4kW
L
0.1kW Without brake
33
Fig. 2
0.2~0.4kW Without brake
Motor Power
52
M4-earth bolt
0.1kW
48
60
24
PF 1/2
V
W
U
0.2kW
Terminal box
0.4kW
134
J
J
J
Fig. 1
L
J
L
L
Fig. 3
0.1kW Without brake
Model
RNYM01-1010-5~10
RNYM01-1120-5~60
RNYM01-1220-40~60
RNYM01-1230-80~240
RNYM01-1330-80~240
RNYM01-1340-300~1440
RNYM01-1440-300~1440
RNYM02-1110-5~10
RNYM02-1120-5~30
RNYM02-1220-5~60
RNYM02-1320-40~60
RNYM02-1330-80~240
RNYM02-1430-80~240
RNYM02-1440-300~1440
RNYM02-1540-300~1440
RNYM05-1210-5~10
RNYM05-1220-5~30
RNYM05-1320-5~60
RNYM05-1420-40~60
RNYM05-1430-80~240
RNYM05-1530-80~240
RNYM05-1540-300~1440
RNYM05-1640-300~1440
Fig. 4
L
240
285
308
309
331
354
396
275
310
333
361
356
384
421
465
311
353
381
412
404
437
485
543
0.2~0.4kW Without brake
J
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
105
Mass(kg)
5.5
7.0
8.0
8.5
10
10.5
15
6.5
8.0
9.5
11
10
16
16
25
9.5
10.5
12
16
17
24
26.5
63.5
Fig.
1
1
1
3
3
3
3
2
2
2
2
4
4
4
4
2
2
2
2
4
4
4
4
0.75~5.5kW 3-phase Motor Increased Safety Type (eG3)
0.75
kW
~
RNYM Series Hollow Shaft Type
5.5
90
kW
W
Motors without brake are available for the Increased safety type. Dimensions of Increased safety types
(eG3) are as below.
Please refer to page 40–54 for selection tables.
Please let us know the nomenclature, valtage, frequency, and that it is Increased safety (eG3) when ordering
or inquiring.
Increased safety motors conform to eG3 of Japanese Industrial Standards (JIS).
J
J
W
PF 3/4
(5.5kW : PF1)
S
E
Fig. 6
Without brake
M5 earth bolt
Without brake
A
Fig. 5
Motor Power
0.75kW
1.5kW
2.2kW
3.7kW
5.5kW
Model
RNYM1-1310-5~10
RNYM1-1320-5~30
RNYM1-1420-5~60
RNYM1-1520-40~60
RNYM1-1530-80~240
RNYM1-1531-80
RNYM1-1631-150~240
RNYM1-1640-300~1440
RNYM2-1410-5~10
RNYM2-1420-5~30
RNYM2-1520-5~60
RNYM2-1531-40~80
RNYM2-1630-80~120
RNYM2-1631-150~240
RNYM3-1510-5~10
RNYM3-1520-5~30
RNYM3-1531-40~80
RNYM3-1630-80~120
RNYM3-1631-150~240
RNYM5-1521-5~25
RNYM5-1522-5~15
RNYM5-1632-30~60
RNYM5-1633-20~60
RNYM8-1522-5~15
RNYM8-1633-20~40
J
136
136
136
136
136
136
136
136
141
141
141
141
141
141
148
148
148
148
148
183
183
183
183
183
183
A
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
100
123
123
123
123
123
123
E
57
57
57
57
57
57
57
57
57
57
57
57
57
57
57
57
57
57
57
65
65
65
65
65
65
R
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
75
87
87
87
87
87
87
W
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
72
90
90
90
90
90
90
S
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
35.5
45
45
45
45
45
45
Mass(kg)
13.5
14
18
27
26
27
47
69
22.5
22
32
31
53
54
29.5
35
35
58
58
51
51
70
71
58
78
Fig.
5
5
5
5
6
6
6
6
5
5
5
6
6
6
5
5
6
6
6
6
6
6
6
6
6
eG3
Terminal box
135
90
W
136
MEMO
IP65
Technical Data
Technical Data
137
129
Selection procedure
1. Hollow shaft type (RNYM series)
TR : Actual transmitted torque on slow speed
shaft of a gear motor [N . m]
Tout : Allowable output torque of a gear motor
[N . m]
Te : Equivalent transmitted torque [N . m]
Pr : Actual radial load [N]
Selection
procedure
Determine equivalent transmitted
torque [Te]
Te=TR✕load factor of gear motor [N·m]
Pro
Lf
Cf
Fs
AR
ARO
: Allowable radial load [N]
: Location factor
: Coupling factor
: Shock factor
: Torque arm length [mm]
: Standard torque arm length [mm]
TR (50 N.m)
Actual transmitted torque
SF (1.0)
(50=50✕1.0)
Load conditions,
Operation time
Table 9
Page 134
Reduction ratio and output speed
Output speed n2
r/min
50Hz
60Hz
290
350
207
250
145
175
121
146
96.7
117
72.5
87.5
58.0
70.0
48.3
58.3
Te
(50N.m)
*Motor slippage is
not accounted for in
output speed
Output speed, Power
supply frequency
Selection
Example
TR=50 [N-m]
Chain conveyor
(uniform load)
10 hrs/day
50 [r/min]
50 [Hz]
3-phase motor
Indoor type
Hollow shaft type
Reduction ratio (30)
> Te
*In case SF is ✽, select the model Tout =
Determine Model (input power, frame size
and reduction ratio)
Tout
servise factor
Select model Tout✕SF( of gear motor )=> Te
*
Selectin tables
[Flange/foot mount]
Page 18–54
●Pr=1500 [N]
(67.3✕1.00 => 50)
Model (RNYM05-1220–
–
●Load point : L=20 [mm]
–30)
●Shock: negligible
●Coupling: chain
Flange mount /
foot mount
Check radial load
Shaft top mount
Pr (1500N)
Actual radial load
Note 2
Pr =<
Pro
Lf5Cf5Fs
Lf (1.0)
Table 1
Location factor
Cf (1.0)
<
(1500 =
1520
)
1.051.051.0
Table 2
Fs (1.0)
Page 18–54
AR (200A)
Check torque
arm length (AR)
Lf (1.0)
AR => ARO✕Lf✕Fs
Fs (1.0)
Torque arm length
(200 => 100✕1✕1)
Coupling factor
Shock factor
Table 3
When the load is out
of allowable range,
use one bigger input Pro (1520N)
power or frame size
and check it again.
Selection tables
coupling
Check driven
shaft strength
Note 1
Table 1
Location factor
Table 3
Shock factor
Table 4
Standard torque
arm length
ARO
(100A)
[Shaft mount ]
●AR: 200 [mm]
●Load point: 20 [mm]
away from output shaft
end
●Shock: negligible
Check strength of
driven shaft, bearings
and torque arms.
(Refer
to
page
150–151)
AR
Determine a model
Refer to 15 for nomenclature
Model (RNYM05-1220–
–
–30)
Confirm specifications and dimensions
●Confirm specifications: Refer to page 14.
*Specify supply voltage and outdoor/indoor usage
when placing your order.
●Confirm dimensions: Refer to page 18–54.
Model (RNYM05–1220–30)
138
3-phase
Without brake
Motor type
Brake
Note 1: Torque arm length is a distance between the center of driven shaft and the torque arm whirl stop.
Note 2: Refer to page 144 for the formula in case of axial load
Table 1 Location factor [Lf]
Frame size
03, 07
17
60, 63, 64
1010
1120
1210, 1220, 1230, 1240
1310, 1320, 1330, 1340
1410, 1420, 1430, 1440
1510,1520,1521,1522,1530,1531,1540
1630, 1631, 1632, 1633, 1640
10
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
20
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
30
1.2
1.2
1.1
1.2
1.2
1.2
1.1
1.1
1.1
1.1
40
1.3
1.3
1.2
1.3
1.3
1.3
1.2
1.2
1.2
1.2
L (mm)
50
1.4
1.4
1.2
1.4
1.4
1.4
1.3
1.3
1.3
1.2
60
1.5
1.5
1.3
1.5
1.5
1.5
1.4
1.4
1.3
1.3
70
1.7
1.6
1.3
1.7
1.6
1.6
1.5
1.4
1.4
1.3
80
1.8
1.7
1.4
1.8
1.8
1.7
1.6
1.5
1.5
1.4
90
1.9
1.8
1.4
1.9
1.9
1.8
1.7
1.6
1.5
1.4
)
Flange mount
Foot mount
L
( )
Shaft
mount
(
Pr
L
Note: "L" indicates the distance from hollow shaft end to the point of redial load.
Table 3 Shock factor [Fs]
Table 2 Coupling factor [Cf]
Coupling method
Cf
Degree of shock
Fs
Chain
1
Negligible shock
1
Gear
1.25
Moderate shock
1~1.2
V-belt
1.5
Heavy shock
1.4~1.6
Table 4 Standard torque arm length [ARO]
AR0
Frame size
50
80
100
120
1410,1420
1510,1520
1230
1330
AR0
140
150
100
130
Frame size
1430
1530,1531
1630,1631,1632,1633
AR0
160
200
280
AR
Technical Data
Frame size
03,07,17,1010
1110,1120
1210,1220
1310,1320
139
Selection procedure
Flange mount type (RNFM series)
Foot mount type (RNHM series)
2. Solid shaft type
Pro
Lf
Cf
Fs
TR : Actual transmitted torque on slow speed
shaft of a gear motor [N.m]
Tout : Allowable output torque of a gear motor
[N.m]
Te : Equivalent transmitted torque [N.m]
Pr : Actual radial load [N]
Selection
procedure
: Allowable radial load [N]
: Location factor
: Coupling factor
: Shock factor
TR (50 N.m)
Determine equivalent transmitted
torque [Te]
Te=TR✕load factor of gear motor [N·m]
SF (1.0)
Selection
Example
Actual transmitted torque
Load conditions,
Operation time
Table 9
(50=50✕1.0)
Reduction ratio and output speed
Output speed n2
r/min
50Hz
60Hz
290
350
207
250
145
175
121
146
96.7
117
72.5
87.5
58.0
70.0
48.3
58.3
Te
(50N.m)
*Motor slippage is
not accounted for in
output speed
Select model Tout✕SF
(
)
Selectin tables
Tout
Te
●Sprocket pitch circle
Page 88–92
dia.90 [mm]
Radius R=0.045 [m]
(67.3✕1.00 => 50)
Model (05-1220
-30)
●Pr = TR =
Check radial load
Note.1
Pr =<
<
(1110 =
R
Pr (1110N)
Pro
Lf✕Cf✕Fs
Actual radial load
Lf (1.0)
Table 5,6
Radial load location
Table 7
Coupling
Table 8
Shock factor
Cf (1.0)
1520
)
1.1✕1.0✕1.0
When the load is out of allowable range, use
a bigger input power or frame size and check
it again.
Fs (1.0)
50
0.045
·=1110N
·
●Load point: L=20 [mm]
●Coupling: chain
coupling
●Shock: negligible
Selection tables
Pro
(1520N)
Model (05-1220
50 [r/min]
50 [Hz]
3-phase motor
Indoor type
Flange mount type
> Te
*In case SF is ✽, select the model Tout =
Determine Model (input power, frame size
and reduction ratio)
servise factor >
of gear motor =
Chain conveyor
(uniform load)
10 hrs/day
Regarding selection of
0.1kW–5.5kW please refer
to page 24–54 for selection table
Reduction ratio (30)
*
Output speed, Power
supply frequency
TR=50 [N·m]
Page 88–92
-30)
Determine a model
Refer to 15 and 16–111 for nomenclature
Model (RNFM05-1220L–✕1–
(RNFM-Flange mount)
(L-left)
Mounting
Shaft direction
–30)
●Left (Viewed from
motor)
Confirm specifications and dimensions
●Confirm specifications: Refer to page 14.
*Specify supply voltage and outdoor/indoor usage
when placing your order.
●Confirm dimensions: Refer to page 106–111.
●Flange mount
3-phase
Without brake
Motor type
Brake
Model (RNFM05–1220L–✕1–30)
Note 1: Values and models in bracket ( ) for the selection example.
Note 2: Refer to page 144 for the formula in case of axial load.
140
(1) 15W–90W, 3.0kW–5.5kW, 0.1kW–0.75kW Ratio 1/300–1/1440, Frame size 60, 63,
Table 5 Location factor [Lf]
Load location
Lf
Shaft root
0.8
Shaft center
1.0
Shaft end
1.4
(2) 0.1kW–2.2kW (Ratio 1/5–1/240) (Without frame size 60, 63, 64)
Table 6 Location factor [Lf]
RNFM-X1 RNHM-J1
Flame Size
1120
1220
1320
1420
1520
1230
1330
1430
1530, 1531
10
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
1.0
20
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
1.1
30
1.2
1.2
1.1
1.1
1.1
1.3
1.2
1.3
1.1
40
1.3
1.3
1.2
1.2
1.2
1.7
1.2
1.7
1.2
L (mm)
50
1.4
1.5
1.3
1.3
1.3
2.2
1.3
2.2
1.3
60
1.6
1.8
1.4
1.4
1.3
2.6
1.4
2.6
1.3
70
1.8
2.1
1.5
1.6
1.4
3.0
1.7
3.0
1.4
80
2.1
2.4
1.6
1.8
1.5
3.5
1.9
3.5
1.5
90
1.2
1.2
1.3
1.3
1.5
1.6
1.3
2.5
1.6
20
1.3
1.5
1.4
1.2
1.1
1.2
1.1
1.1
1.1
30
1.4
1.6
1.5
1.3
1.2
1.3
1.2
1.3
1.2
40
1.6
1.7
1.5
1.4
1.3
1.7
1.3
1.7
1.3
L (mm)
50
1.7
1.8
1.6
1.5
1.4
2.2
1.4
2.2
1.4
60
1.8
1.9
1.7
1.5
1.4
2.6
1.5
2.6
1.4
70
1.9
2.1
1.8
1.6
1.5
3.0
1.7
3.0
1.5
80
2.0
2.4
1.9
1.8
1.6
3.5
1.9
3.5
1.6
90
1.4
1.6
1.6
1.5
1.6
1.6
1.3
2.5
1.6
L
L
Pr
Pr
RNHM–J1
RNFM–X1
RNFM-P1, Q1
1120
1220
1320
1420
1520
1230
1330
1430
1530, 1531
10
1.2
1.3
1.3
1.2
1.1
1.1
1.0
1.1
1.1
Table 7 Coupling factor [Cf]
L
Pr
RNFM–P1
Table 8 Shock factor [Fs]
Coupling method
Cf
Degree of shock
Fs
Chain
1
Negligible shock
1
Gear
1.25
V-belt
L
Moderate shock
1~1.2
Heavy shock
1.4~1.6
Pr
RNFM–Q1
Technical Data
Flame Size
1.5
141
Selection procedure
3. Selection of load factor
The Load Factor is rated for the characteristics of the driven machine.
The tabulated ratings are based on a running time of 10 hours per day with uniform load.
For your reference, please see method 1 and 2 shown below.
1 Recommended Load Factor by the Driven Application.
Table 9 Service Factor [S.F.]
Operation time
Load conditions
10 hrs/
day max.
10~24hrs/
day max.
Uniform
1
1.25
Conveyors (uniform load), Pumps (centrifugal), Food processing machine (rice
polishers, canning machines), Elevators (uniform load), Plastic extruders,
Agitators (pure liquid), Bar screens
Applications
Moderate shock
1.25
1.5
Conveyors (variable speed and heavy duty), Food processing machine (peat
slicer, dough mixer, meat grinder), Elevators (heavy duty), Agitators (liquid and
solid, variable-density liquid), Feeders (belts, aprons, screws), Thickeners,
Flocculators, Machine tools
Heavy shock
1.75
2.0
Punching presses, Tapping machine, Crushers (crusher mills), Hoists (heavy
duty), Drum barkers, Log hauls, Cutters, Platers
Note 1: The service factors and applications in the above table are only for your relerence. Actual applications and their characteristics may be variable.
2Recommended Load Factor Modifications for Frequent Start-Stop Operation.
Please select a model using Table 8 and check the motor thermal rating (Table 10)
Table 10 Number of Starts-Stops and Load Factor.
~10 hours/day
24 hours/day
Number of starts-stops
(Times/hour)
I
II
III
I
II
III
~10
1.00
1.15
1.50
1.20
1.30
1.65
~200
1.10
1.35
1.65
1.30
1.50
1.85
~500
1.15
1.50
1.80
1.40
1.65
2.00
The ratio of Moment of Inertia (The ratio of GD2) =
Total Moment of Inertia (GD2) as seen from the motor shaft
Moment of Inertia (GD2) of motor
I : Allowable ratio of Moment of Inertia (GD2) =< 0.3
II : Allowable ratio of Moment of Inertia (GD2) =< 3
III : Allowable ratio of Moment of Inertia (GD2) =< 10
Note : 1. The number of starts-stops includes brake or clutch operation times.
Note : 2. Consult us when starting under loaded conditions.
142
Table 11 Motor thermal rating (C✕Z)
Note : Contact us regarding a motor for inverters and a single-phase motor.
Output Motor Allowable C×Z Allowable C×Z Allowable C×Z Allowable C×Z Motor moment of inertia kgf . m2
kW
(35%ED)
(35%ED~50ED%) (50%ED~80ED%) (80%ED~100ED%)
Standard
With brake
Motor GD2
kgf.m2
Standard
With brake
0.1
3200
3000
2000
1200
0.00033
0.00035
0.0013
0.0014
0.2
2200
2800
2800
2500
0.00050
0.00055
0.002
0.0022
0.25
2200
2800
2800
2500
0.00050
0.00055
0.002
0.0022
0.4
1800
2200
1500
1500
0.00065
0.00068
0.0026
0.0027
0.55
1800
2200
1500
1500
0.00101
0.00111
0.00405
0.00445
0.75
1400
1400
800
500
0.00120
0.00130
0.0048
0.0052
1.1
1400
1400
800
500
0.00185
0.00208
0.0074
0.0083
1.5
1200
1200
500
400
0.00213
0.00235
0.0085
0.0094
2.2
1000
900
400
200
0.00333
0.00373
0.0133
0.0149
3.0
1000
900
400
200
0.00700
0.00810
0.0281
0.0325
3.7
800
800
800
700
0.00848
0.00958
0.0339
0.0383
5.5
300
300
200
150
0.01143
0.01253
0.0457
0.0501
C✕Z calculated below 1 to 3 should be less than allowable C✕Z listed in Table 10.
(1) Obtain the C value.
GDM2 + GDL2
GDM2 : Moment of inertia (kgf·m2) or GD2 (kg·m2) of motor.
C=
GDL2 : Total moment of inertia (kgf·m2) or GD2 (kg·m2) of load as seen from the motor.
GDM2
(2) Obtain the Z value, number of starts per hour.
(a) Assume that one operating period consists of "on time" ta (sec), "off time" tb (sec)
and the motor is started nr (times/cycle)
3600nr
(times/hr)
ta+tb
(b) When inching, ni (times/cycle) is included in 1 cycle (ta+tb), the number of inching times per hour Zi,
and then included in the number of starts.
Zi=
3600ni
(times/hr)
ta+tb
(c) Calculate Z (times/hr) by (a) and (b).
Z =Z r+1/2 · Z i =
3600
ta+tb
(nr+
Technical Data
Zr=
1
ni) (times/hr)
2
(3) Calculate C multiplied by Z.
Use the C obtained in step 1 and Z in step 2.
(4) Obtain the duty cycle %ED and check with table above.
%ED =
ta
✕100
ta+tb
143
Construction
Hollow shaft type example (RNYM1-1530-120)
Part No.
144
Description
Part No.
Description
Part No.
Description
Part No.
Description
1
Casing (1)
4
Gear
7
Bearing
10
Output shaft
2
Gear
5
Pinion shaft
8
Bearing
11
Oil seal
3
Pinion shaft
6
Hypoid pinion shaft
9
Hypoid gear
12
Casing (2)
Moment of inertia
(1) Moment of inertia of rotating motion
Rotating motion on the center of gravity
Rotating motion off the center of gravity
R dmf
D dmf
1
J= 8 MD2 [kg.m2]
D [m]
M [kg]
M
J=
4
( 12 D +4R ) [kg.m ]
2
2
2
M dkgf
R dmf
D [m]
1
J= 8 M (D2+d2) [kg.m2]
d [m]
a dmf
M [kg]
M dkgf
bdmf
a [m]
J=
4
c dmf
1
J= 12 M (a2+b2) [kg.m2]
b [m] M [kg]
M a2+b2
2
. 2
3 +4R [kg m ]
(
)
1
J= 12 M (4L2+C2) [kg.m2]
L dmf M dkgf
(2) Moment of inertia of rectilinear motion
V [m/min]
D [m]
J= M
4
General application
(
V
›·Ns
2
) = M4 D
[kg.m2]
2
Ns [r/min]
V [m/min]
M3 [kg]
Horizontal motion
by conveyor
D [m]
M1 [kgf]
M1+M2
J= M
+M3+M4 5D2
2
4
M2 [kg]
(
Ns [r/min]
D [m]
)
[kg.m2]
M4 [kgf]
V [m/min]
Horizontal motion
M [kg]
V
M
J= 4 ›·Ns
(
Ns [r/min]
by lead screw
2
) = M4 ( P› )
2
[kg.m2]
Lead wire : P [m/rev]
Ns [r/min]
M2 [kg]
Vertical motion
by hoist
D [m]
M1 D 2 1
J= 4 + M2D2
8
V [m/min]
[kg.m2]
M1 [kgf
(3) Calculation of moment of inertia at different rotating speeds
Ns1(r/min)
Ns2 (r/min)
Moment of inertia J
Ns2
JR= Ns1
(
2
)J
Technical Data
JR
145
GD2
(1) GD2 of rotating motion
Rotating motion on the center of gravity
Rotating motion off the center of gravity
R [m]
D [m]
1
GD = 2 WD2
[kg.m ]
2
D [m]
W [kgf]
2
a [m]
[kg.m ]
2
b [m]
.
( a +b
3 +4R ) [kg m ]
W [kgf]
b [m]
W [kgf]
W [kgf]
GD2=W
2
2
2
R [m]
1
GD = 2 W (D2+d2)
2
a [m]
( 12 D +4R ) [kg.m ]
W [kgf]
D [m]
d [m]
GD2=W
1
GD2= 3 W (a2+b2)
c [m]
[kg.m2]
2
2
2
1
GD2= 3 W (4L2+C2) [kg.m2]
L [m]
W [kgf]
(2) GD2 of rectilinear motion
V [m/min]
D [m]
2
GD2=W
General application
( › V· N ) =WD
[kg.m2]
2
N [rpm]
V [m/min]
W3 [kgf]
Horizontal motion
by conveyor
W1 [kgf]
D [m]
W2 [kgf]
N [rpm]
D [m]
GD2=
+W +W ) ✕D
( W +W
2
1
2
3
4
2
[kg.m2]
W4 [kgf]
V [m/min]
Horizontal motion
2
W [kgf]
N [rpm]
by lead screw
GD2=W
( › V· N ) =W ( P› )
2
[kg.m2]
Lead wire : P [m/rev]
N [rpm]
W2 [kgf]
Vertical motion by hoist
D [m]
GD2=W1D2+
V [m/min]
1
W 2D 2
2
W1〔kgf]
(3) Calculation of GD2 at different rotation speeds
GDR2
N1(rpm)
N2(rpm)
146
Load GD2
2
N2
GDR2= N1
2
( ) GD
2
[kg.m2]
Moment of inertia and GD2 of geamotors
Table 12
15W
3-phase
In door
Water
proof
Single-phase
Single-phase reversible
3-phase
Single-phase
Single-phase reversible
Motor Flame size
Without brake
With brake
Without brake
With brake
Without brake
With brake
Without brake
With brake
25W
40W
Moment of inertia
GD2
Moment of inertia
GD2
Moment of inertia
GD2
Moment of inertia
GD2
kg·m2
kgf·m2
kg·m2
kgf·m2
kg·m2
kgf·m2
kg·m2
kgf·m2
01#, 03#
0.000050
0.00020
0.000070
0.00028
0.000050
0.00020
0.000070
0.00028
0.000050
0.00020
0.000070
0.00028
0.000050
0.00020
0.000070
0.00028
01#, 03#
0.000058
0.00023
0.000078
0.00031
0.000058
0.00023
0.000078
0.00031
0.000058
0.00023
0.000078
0.00031
0.000058
0.00023
0.000078
0.00031
05#, 07#
0.000070
0.00028
0.000090
0.00036
0.000070
0.00028
0.000090
0.00036
0.000070
0.00028
0.000090
0.00036
0.000070
0.00028
0.000090
0.00036
60W
Motor type
3-phase
In door
Water
proof
Single-phase
Single-phase reversible
3-phase
Single-phase
Single-phase reversible
Motor Flame size
Without brake
With brake
Without brake
With brake
Without brake
With brake
Without brake
With brake
90W
GD2
Moment of inertia
GD2
Moment of inertia
GD2
Moment of inertia
GD2
kg·m2
kgf·m2
kg·m2
kgf·m2
kg·m2
kgf·m2
kg·m2
kgf·m2
07#
0.000070
0.00028
0.000090
0.00036
0.000070
0.00028
0.000090
0.00036
0.000070
0.00028
0.000090
0.00036
0.000070
0.00028
0.000090
0.00036
17#
0.00012
0.00013
0.00016
0.00017
0.00012
0.00013
0.00016
0.00017
0.00049
0.00052
0.00065
0.00068
0.00049
0.00052
0.00065
0.00068
0.2kW
Without brake
With brake for FB
Single-phase Without brake
In door
With brake for FB
For inverter Without brake
With brake for FB
3-phase
Without brake
With brake forFB
Out door
Single-phase Without brake
Light dust
With brake for FB
proof
For inverter Without brake
With brake for FB
Protected
Without brake
explosion proof 3-phase
kg·m
0.00033
0.00035
0.00050
0.00055
0.00050
0.00055
0.00033
0.00035
0.00050
0.00055
0.00050
0.00055
0.00033
kgf·m
0.0013
0.0014
0.0020
0.0022
0.0020
0.0022
0.0013
0.0014
0.0020
0.0022
0.0020
0.0022
0.0013
Motor type
Moment of inertia
GD2
Moment of inertia
GD2
Moment of inertia
kg·m2
0.00120
0.00130
0.00213
0.00235
0.00120
0.00130
0.00213
0.00235
0.00120
kgf·m2
0.0048
0.0052
0.0085
0.0094
0.0048
0.0052
0.0085
0.0094
0.0048
kg·m2
0.00185
0.00208
–
–
0.00185
0.00208
–
–
–
kgf·m2
0.0074
0.0083
–
–
0.0074
0.0083
–
–
–
kg·m2
0.00213
0.00235
0.00333
0.00373
0.00213
0.00235
0.00333
0.00373
0.00213
2
kg·m
0.00050
0.00055
0.00065
0.00068
0.00065
0.00068
0.00050
0.00055
0.00065
0.00068
0.00065
0.00068
0.00050
2
0.75kW
3-phase
In door
For inverter
3-phase
Out door
Light dust
For inverter
proof
Protected
explosion proof
3-phase
Without brake
With brake for FB
Without brake
With brake for FB
Without brake
With brake for FB
Without brake
With brake for FB
Without brake
3-phase
In door
For inverter
3-phase
Out door
Light dust
For inverter
proof
Protected
explosion proof
3-phase
Without brake
With brake for FB
Without brake
With brake for FB
Without brake
With brake for FB
Without brake
With brake for FB
Without brake
Moment of inertia
kgf·m
0.0020
0.0022
0.0026
0.0027
0.0026
0.0027
0.0020
0.0022
0.0026
0.0027
0.0026
0.0027
0.0020
2
kg·m
0.00065
0.00068
–
–
–
–
0.00065
0.00068
–
–
–
–
–
2
0.4kW
GD2
kgf·m
0.0026
0.0027
–
–
–
–
0.0026
0.0027
–
–
–
–
–
2
1.5kW
0.55kW
Moment of inertia
GD2
kg·m
0.00065
0.00068
0.00120
0.00130
0.00120
0.00130
0.00065
0.00068
0.00120
0.00130
0.00120
0.00130
0.00065
kgf·m
0.0026
0.0027
0.0048
0.0052
0.0048
0.0052
0.0026
0.0027
0.0048
0.0052
0.0048
0.0052
0.0026
2
Moment of inertia
2
2.2kW
GD2
kgf·m2
0.0085
0.0094
0.0133
0.0149
0.0085
0.0094
0.0133
0.0149
0.0085
kg·m
0.00101
0.00111
–
–
–
–
0.00101
0.00111
–
–
–
–
–
2
GD2
kgf·m2
0.00405
0.00445
–
–
–
–
0.00405
0.00445
–
–
–
–
–
3.0kW
Moment of inertia
GD2
Moment of inertia
GD2
kg·m2
0.00333
0.00373
0.00848
0.00958
0.00333
0.00373
0.00848
0.00958
0.00333
kgf·m2
0.0133
0.0149
0.0339
0.0383
0.0133
0.0149
0.0339
0.0383
0.0133
kg·m2
0.00703
0.00813
–
–
0.00703
0.00813
–
–
–
kgf·m2
0.0281
0.0325
–
–
0.0281
0.0325
–
–
–
5.5kW
Moment of inertia
GD2
kg·m
0.00848
0.00958
0.0114
0.0125
0.00848
0.00958
0.0114
0.0125
0.00848
kgf·m
0.0339
0.0383
0.0457
0.0501
0.0339
0.0383
0.0457
0.0501
0.0339
2
GD2
1.1kW
3.7kW
Motor type
36#, 361#
0.00033
0.0013
0.00035
0.0014
–
–
–
–
–
–
–
–
–
–
–
–
0.25kW
GD2
2
Moment of inertia
15#,17#
0.00015
0.00058
0.00016
0.00062
0.00021
0.00083
0.00022
0.00086
0.00015
0.00058
0.00016
0.00062
0.00021
0.00083
0.00022
0.00086
Moment of inertia
3-phase
0.00043
0.00047
0.00058
0.00061
0.00043
0.00047
0.00058
0.00061
Moment of inertia
0.1kW
Motor type
17#
0.00011
0.00012
0.00015
0.00015
0.00011
0.00012
0.00015
0.00015
2
Moment of inertia
GD2
kg·m
0.0114
0.0125
–
–
0.0114
0.0125
–
–
0.0114
kgf·m2
0.0457
0.0501
–
–
0.0457
0.0501
–
–
0.0457
2
Technical Data
Motor type
Note 1. Moment of inertia/GD2 on reducer and motor accounted for in
the value stipulated in the tables.
Note 2. The values in the tables are subject to change without notice.
147
Rotating direction & Reduction ratio
a. 3-phase motor (15W–90W)
Motor shaft will be rotating clockwise looking from the fan cover side when wire is connented as shown in connection figure in page
168–169.
The direction of output shaft rotation will be as in the arrows of diagrams below.
Frame size
01,03,05,07
15,17
1240
148
Reduction ratio
5, 80, 100, 120, 160, 200, 240
5, 7.5, 10, 12, 80, 100, 120, 150, 200, 240
300, 360, 480, 600, 720, 900, 1200, 1440
Frame size
01,03,05,07
15,17
1240
Reduction ratio
7.5, 10, 12, 15, 20, 25, 30, 40, 50, 60
15, 20, 25, 30, 40, 50, 60
—
RNYM series
RNYM series
RNFM series
RNFM series
b. 3-phase motor and motor for inverter (0.1kW–5.5kW)
Motor shaft will be rotating counter clockwise looking from the fan cover side when wire is connented as shown in connection figure in
page 168–173.
The direction of output shaft rotation will be as in the arrows of diagrams below.
Reduction ratio
—
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
300, 360, 480, 600, 720, 900, 1200, 1440
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
300, 360, 480, 600, 720, 900, 1200, 1440
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
300, 360, 480, 600, 720, 900, 1200, 1440
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
5, 7, 10, 12, 15, 20, 25
5, 7, 10, 12, 15
—
—
300, 360, 480, 600, 720, 900, 1200, 1440
—
—
30
20, 25
300, 360, 480, 600, 720, 900, 1200, 1440
Frame size
1010
1110
1120
1210
1220
1230
Reduction ratio
5, 7, 10
5, 7, 10
—
5, 7, 10
—
80, 100, 120, 150, 200, 240
1310
1320
1330
5, 7, 10
1410
1420
1430
5, 7, 10
1510
1520
5, 7, 10
1530
1531
80, 100, 120, 150, 200, 240
40, 50, 60, 80
1630
1631
1632
1633
1640
80, 100, 120
150, 200, 240
40, 50, 60
30, 40
—
80, 100, 120, 150, 200, 240
—
80, 100, 120, 150, 200, 240
—
—
RNYM series
RNYM series
RNFM series
RNFM series
RNHM series
RNHM series
R type
L type
T type
Technical Data
Frame size
1010
1110
1120
1210
1220
1230
1240
1310
1320
1330
1340
1410
1420
1430
1440
1510
1520
1521
1522
1530
1531
1540
1630
1631
1632
1633
1640
R type
L type
T type
149
c. Single-phase motor
Motor shaft will be rotating clockwise looking from the fan cover side when wire is connented as shown in connection figure in page
163–167.
The direction of output shaft rotation will be as in the arrows of diagrams below.
Frame size
01,03,05,07
15,17
1110
1120
1210
1220
1240
1310
1320
1330
1340
1420
1430
1440
1530
1540
1640
Reduction ratio
5, 80, 100, 120, 160, 200, 240
5, 7.5, 10, 12, 80, 100, 120, 150, 200, 240
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
300, 360, 480, 600, 720, 900, 1200, 1440
—
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
300, 360, 480, 600, 720, 900, 1200, 1440
5, 7, 10, 12, 15, 20, 25, 30, 40, 50, 60
—
300, 360, 480, 600, 720, 900, 1200, 1440
—
300, 360, 480, 600, 720, 900, 1200, 1440
300, 360, 480, 600, 720, 900, 1200, 1440
Reduction ratio
7.5, 10, 12, 15, 20, 25, 30, 40, 50, 60
15, 20, 25, 30, 40, 50, 60
5, 7, 10
—
5, 7, 10
—
1310
1320
1330
5, 7, 10
1420
1430
—
80, 100, 120, 150, 200, 240
1530
80, 100, 120, 150, 200, 240
—
80, 100, 120, 150, 200, 240
—
1640
RNYM series
RNYM series
RNFM series
RNFM series
RNHM series
RNHM series
R type
L type
T type
150
Frame size
01,03,05,07
15,17
1110
1120
1210
1220
R type
L type
T type
Actual reduction ratio
Table 13 Actual reduction ratio RNYM, RNFM, RNHM series (Reduction raito: 5~240)
Frame size
03
17
1010
1110
1210
1310
1410
1510
1120
1220
1320
1420
1520
1521
1522
1230
1330
1430
1530
1531
1630
1631
1632
1633
07
Reduction ratio
5
5.01
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.00
5.06
7
7.00
7.00
7.00
7.00
7.00
7.00
7.03
7.03
7.03
6.97
7.03
7.03
7.00
7.5
10
12
7.50 10.00 12.27
7.50 10.18 12.00
10.00
10.00
10.00
10.00
10.00
10.00
9.81 11.74
9.81 11.74
9.81 11.74
10.00 11.96
9.81 11.74
9.81 11.74
10.00 12.21
15
20
25
30
40
50
60
80
100 120 150 160 200 240
160.0 200.00 243.64
15.00 20.00 24.55 30.00 40.00 50.00 60.91 80.00 100.00 121.82
195.61 234.64
15.00 20.36 25.42 30.48 40.00 50.71 60.83 80.00 103.16 120.00 152.14
15.26
15.26
15.26
14.75
15.26
15.26
15.25
20.67
20.67
20.67
19.69
20.67
20.67
24.62
24.62
24.62
25.00
24.62
24.62
30.00
30.00
30.00
30.45
30.00
41.33
41.33
41.33
39.38
41.33
49.23
49.23
49.23
50.00
49.23
60.00
60.00
60.00
60.91
60.00
81.45 101.01 120.15 151.51
81.94 102.27 122.54 153.40
80.37 102.35 122.64 153.52
79.63 101.32 119.17 149.65
39.20 49.88 57.60 77.42
80.50 102.94 119.00
154.41
29.24 41.16 49.00 56.35
20.88 24.33 29.40 40.25 51.47 59.50
200.39 231.27
199.13 232.50
199.29 240.00
188.57 232.25
195.42 244.07
Note: The values in the tables are subject to change without notice.
Table 14 Actual reduction ratio RNYM series (Reduction raito: 300~1440)
1240
1340
1440
1540
1640
Reduction ratio
300 360 480 600 720 900 1200
297.57 346.15 485.71 626.32 728.57 923.72 1159.41
302.72 360.10 479.79 595.00 707.78 892.50 1180.45
301.12 360.81 498.18 621.72 744.97 932.59 1210.57
311.59 373.36 502.52 602.13 753.78 903.20 1194.57
297.68 350.10 475.66 605.28 711.87 907.91 1144.07
1440
1424.62
1382.22
1413.28
1403.08
1396.15
Technical Data
Frame size
151
Allowable axial load on output shaft (Pao) [N/kgf]
When radial and axial loads are posed simultaneously.
( PrPro· Lf
Pa
+ Pao
) · Cf · Fs
<
=1
Check your selection to be within the formula.
Pr
Pro
Pa
Pao
Lf
Cf
Fs
: Actual radial load
: Allowable radial load
: Actual axial load
: Allowable axial load
: Load location factor
: Coupling factor
: Sock factor
(refer to selection tables)
(refer to Table 1 of page 131, Table 5, 6 of page 133 )
(refer to Table 2 of page 131, Table 7 of page 133)
(refer to Table 3 of page 131, Table 8 of page 133)
Table 15 Allowable axial load on output shaft (3/single-phase)
Frame size
N/kgf
01, 03, 05, 07
294N/30kgf
15, 17
294N/30kgf
1010, 1110, 1210, 1310, 1410, 1510
0N/0kgf
1120
294N/30kgf
1220, 1230
784N/80kgf
1320, 1330
980N/100kgf
1420, 1430
1470N/150kgf
1520, 1521, 1522, 1530, 1531
2940N/300kgf
1630, 1631, 1632, 1633, 1640
5390N/550kgf
Note: Radial load on output shaft not accounted for in the calculation above.
Lubrication
• As Hyponic Drives are sealed with long-life grease, replenishment is practically unnecessary, but overhaul in approximately
20,000 hours or 3~5 years of operation will provide longer service life.
• The durability of oil seals is subject to operating conditions. It may be required to change them in less than 20,000 hours or
three years of operation under severe conditions.
• Overhaul of gear motors must be performed at our specified sites with professional knowledge and technique.
152
Detail dimensions
Hollow shaft type (RNYM series) output shaft bore size
Bore (mm)
Frame size
15
20
25
30
35
38
40
45
50
55
●
03, 07, 17, 1010
●
1110, 1120
●
1210, 1220, 1230, 1240
●
1310, 1320, 1330, 1340
1410, 1420, 1440
●
1430
●
●
1510, 1520, 1521, 1522, 1530, 1531, 1540
●
1630, 1631, 1632, 1633, 1640
● Standard
Semi-standard
(Contact us for price and delivery.)
Output shaft dimensions
L (Recommended length
of driven shaft)
L (Recommended length
of driven shaft)
D
H
J
C
F
E
A
G
B
B
A
A
Bore diameter
A-A
Frame size
03, 07
17
1010
1110, 1120
1210, 1220
1230, 1240
1310, 1320, 1330,
1340
1410, 1420, 1440
1430
1510, 1520, 1521,
1522, 1530, 1531,
1540
1630, 1631, 1632,
1633, 1640
Bore
A
B
15
15
15
20
20
25
20
25
20
25
30
25
30
35
25
30
35
38
30
35
38
40
45
40
45
50
55
78
94
82
82
92
92
100
100
110
110
110
138
138
138
138
138
138
138
156 (160)
156 (160)
156 (160)
156 (160)
156 (160)
224
224
224
224
28
28
28
30
31
38
31
38
31
38
46
38
46
52
38
46
52
58
46
52
58
60
67
60
67
76
85
C
D
E
F
G
H
J
L
—
—
—
—
—
—
15.6
15.6
15.6
20.6
20.6
25.6
20.6
25.6
20.6
25.6
30.6
25.6
30.6
35.6
25.6
30.6
35.6
38.6
30.6
35.6
38.6
40.6
45.6
40.6
45.6
50.6
55.6
R1.0
R1.0
R1.0
R1.0
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R1.5
R2.5
5
5
5
6
6
8
6
8
6
8
8
8
8
10
8
8
10
10
8
10
10
12
14
12
14
14
16
17.3
17.3
17.3
22.8
22.8
28.3
22.8
28.3
22.8
28.3
33.3
28.3
33.3
38.3
28.3
33.3
38.3
41.3
33.3
38.3
41.3
43.3
48.8
43.3
48.8
53.8
59.3
55
70
60
60
65
60
75
65
85
80
70
105
95
90
105
95
90
90
130 (135)
115 (120)
110 (115)
105 (110)
100 (105)
180
175
165
155
—
—
—
21
21
26.2
21
26.2
21
26.2
31.4
26.2
31.4
37
26.2
31.4
37
40
31.4
37
40
42.5
47.5
42.5
47.5
53
58
16
15
22
15
22
15
22
22
22
22
26
22
22
26
26
22
26
26
30
30
30
30
30
40
1.15
1.15
1.35
1.15
1.35
1.15
1.35
1.35
1.35
1.35
1.75
1.35
1.35
1.75
1.75
1.35
1.75
1.75
1.95
1.95
1.95
1.95
2.2
2.2
Technical Data
(mm)
Effective
length of
driven shaft
20
35
20
20
55
40
55
40
75
55
45
80
65
50
80
65
50
50
115
100
90
85
70
155
120
110
90
Keyway dimensions in accordance with JIS B 1301-1996 parallel key (Normal Grade). Bore dimension tolerance in accordance with JIS B 0401-1976 "H8".
153
Hollow shaft type (RNYM series) handling precautions
1. Mounting torque arm
a
(1) Mounting on driven shaft
● Apply molybdenum disulfide to the
surface of the driven shaft and the
inside of the hollow shaft, and insert
Hyponic Drive onto the driven shaft.
● When engagement is too tight, lightly
Fig. 1
strike on the end of the hollow output
shaft with a mallet. Never strike on the
casing. It is recommended to make a
jig shown on the right for smooth
insertion.
● The hollow shaft dimension tolerance is in accordance with JIS "H8".
shaft is :
uniform load without impact..............................JIS h6 or js6
shock load or large radial load..........................JIS js6 or k6
●
b
d
a......Retaining ring
b......Spacer
c......Thrust bearing
c
e
d......Nut
e......Double-end
threaded bolt
The recommended tolerance for the driven
Snap ring size is in accordance with JIS B2804C.
(2) Hyponic Drive must be secured to driven shaft.
a) How to secure Hyponic Drive not to move to the machine side (Ex.: Figs.2~4)
Fig. 2 secured by staged shaft
154
Fig.3 secured by spacer
(stageless driven shaft)
Set screw
Stopper ring
Machine side
Spacer
Machine side
Machine side
Bearing unit
Fig. 4 secured by a set screw and a
stopper (stageless driven shaft)
b) How to secure Hyponic Drive not to move off from the machine side (Figs. C5-C7)
Stopper ring
Set screw
End plate
Fig. 5 secured by a spacer and a snap ring
Machine side
Machine side
Spacer
Machine side
Snap ring
Fig. 6 secured by an end plate
Fig. 7 secured by a set screw and a stopper
ring
(3) Torque arm whirl stop
Attach the torque arm to Hyponic Drive casing on the machine side with hex socket head cap screws. (Refer to the table below
for sizes of the bolts.).
Leave some allowance in the section of torque arm whirl stop so that excessive force will not be applied between Hyponic Drive
and the driven shaft. Don't secure the torque arm with the whirl stop bolt. Or it may damage the whirl stop bolt, the torque arm,
Hyponic Drive, or the machine.
In case of frequent start/stop operations, or repeated normal/reverse operations, use a rubber bush between the torque arm and
mounting bolt (or spacer) to absorb the shock.
Torque arm
Plain washer
Keep some
allowance
No allowance
between the
torque arm and
the machine
Rubber bush
Special bolt
(or pin)
A
(Adjust the allowance according to
the movement of the machine.)
(Excessive force on the whirl stop
bolt. machine, and Hyponic may
cause damage.)
Good
Bad
Technical Data
Spacer
Machine side
Fig. 8 Example of whirl stop mounting (Section A)
Frame size
Bolt
03
M5
07, 17
M6
1010, 1110, 1120,1230, 1240
M8
1210, 1220, 1330, 1340
M10
1310, 1320, 1430, 1440
M12
1410, 1420, 1510, 1530,1531,1540
M16
1520, 1521, 1522, 1630, 1631, 1632, 1633, 1640
M20
155
Hollow shaft type (RNYM series) handling precautions
f......Spacer
g......Upper bolt
h......Disc
i......Snap ring
i
(4) Removal from a driven shaft
Handle with care so that excessive force will not be applied
between the casing and the
hollow shaft. It is recommended
to make a jig as shown on the
right for easy removal.
Fig. 9
A
h
f
g
Note:
Parts for mounting,
securing, and removal
should be provided by
the customer.
A~
2. Flange mounting and casing bottom mounting (optional)
Handle with care in order not to
apply excessive force to driven
shaft or hollow shaft by twisting
the Hyponic casing.
Good
Bearing unit
Hollow shaft type
Hyponic Drive
Fig. 10 Flange mounting surface
Bad
Bearing unit
Bad
Bearing unit
Hollow shaft type
Hyponic Drive
Hollow shaft type
Hyponic Drive
(Poor concentricity of the driven
shaft and mounting foucet)
(Poor perpendicularity of the driven shaft
center and mounting flange surface)
(Excessive force on Hyponic and the bearing
unit may cause damage on inner parts.)
156
Torque arm (Option)
· There is an option for attaching torque arms. They can be used for continuous operations and cases where there are infrequent
startup and stops.
· Refer to "Hollow shaft type handling precautions (146–148)" when mounting.
· Torque arm cannot be attached between hollow shaft and motor.
· Refer to "Torque arm designs (150)" and "Examples of torque arm designs (151)" when designing for cases when customers are
preparing their own torque are, when startup and stop is frequent, or torque arm is going to be attached on the motor side. Mount
torque arm to reducer casing using 4 bolts.
Torque arm shape
R2
H
b
R3
R1
a
L
D
R2
D
2- d
C
T
AR
Dimensions
a
b
C
D
H
L
d1
d2
R1
R2
R3
T
03
Frame size
33.2
33.2
46.8
–
61.8
78.4
6
6
–
6
9
3.2
07, 17
36.8
36.8
53.2
18.8
70.7
87.6
7
7
26
7
10.5
3.2
1010
25
25
25
25
45.5
64
7
9
26
7
13.5
3.2
1110
29
29
51
29
72.5
74
7
9
28
8
13.5
3.2
1210
37
37
63
37
88.5
92
9
11
41
9
16.5
4.5
1310
44
44
76
44
108
110
11
14
44.5
11
21
4.5
1410
55
55
85
55
123
132
11
18
49.5
11
27
6
1510
65
65
85
65
130
154
11
22
57
12
33
9
1120
42
32
48
32
69.5
90
7
9
28
8
13.5
3.2
1220
57
40
60
40
85.5
115
9
11
41
9
16.5
4.5
1320
62
46
74
46
107
132
11
14
44.5
12
21
4.5
1420
75
57
83
57
123
158
14
18
49.5
13
27
6
1520, 1521, 1522
80
70
80
–
127
178
14
22
–
14
33
9
1230, 1240
65
40
60
40
82.5
123
9
9
41
9
13.5
3.2
1330, 1340
79
47
83
47
110.5
148
11
11
45
11
21
6
1430, 1440
92
54
106
54
141
174
14
14
50
14
21
6
1530, 1531, 1540
109
64
136
64
181
209
18
18
60
18
27
9
1630, 1631, 1632, 1633, 1640
145
85
195
85
250
274
22
22
80
22
33
12
b
H
a
L
a
C
b
D
AR
AR
H
a
D
b
L
L
C
H
C
Technical Data
Assenbly Example
Note:
· Use torque arm only for whirl stop function.
· Fasten reducer at driven shaft for fixing in axial direction.
157
Torque arm designs
Check the strength of torque arm and driven shaft and the life time of the bearing.
(m)
Brg1
Driven shaft
Brg2
YR
Y
m
Sec. B
G
Torque arm
AG
rotation
AR
rotation
Frame size
AG
03, 07, 17
0.05
1010, 1110, 1230, 1240
0.1
1120, 1210, 1220, 1310, 1330, 1340 ,1430, 1440 0.15
1320, 1410, 1430, 1510, 1540
0.2
1420, 1520, 1530, 1531, 1640
0.25
1630, 1631, 1632, 1633
0.30
approximate values
G
R
1. Torque arm load : R = T+AG·G
AR
2. Brg.1 load
: B1=
m (R–G) –YR·R
R
3. Brg.2 load
: B2=
(R+m) (R–G) –YR·R
R
R
T
G
R
AG
AR
YR
m
R
Y
: Output torque [N·m]
: Hyponic Drive gravity [N]
: Torque arm load [N]
: Distance between the centers of the driven shaft and gravity [m]
: Distance from driven shaft center to torque arm whirl stop [m]
: Distance from the center of Hyponic Drive to torque arm whirl stop [m]
: Distance from the center of Hyponic Drive to Brg 2 [m]
: Distance between Brg.1 and Brg.2 [m]
: Distance between the center of Hyponic Drive and Sec. B [m]
4. Sec. B of driven shaft
<m
: M=YR·R–Y (R–G) 0<Y =
158
Note: Output torque is (+) on the shown rotation, and (-) on the opposite rotation.
Fig. 11 Torque arm mountings and designs
2
3
4
Mounting examples
1
a
a
D
D
c
c
b
b
b
AR
D
03
07
17
d
c
H
d
a
D
d
d
H
a
b
b
b
a
a
D
d
a
b
1120
1220
1230
1320
1331, 361
1420
1430, 461
1520
1530, 1531, 56
60, 63, 64
H
c
AR
H
d
H
AR
a
b
a
a
a
Drawing examples
Drawing examples
a
AR
D
H
AR
AR
Macine side
Attach the torque arm to the
casing on the machine side.
Table. 17 Recommended dimensions of torque arm design
(mm)
Length
Bore
Whirl stop bore
AR
H
D
a
b
c
d
03
80
37
6
33
18
48
6
3.2
07
90
37
7
37
19
55
7
3.2
17
90
37
7
37
19
55
7
4.5
1010
50
50
9
25
25
—
7
3.2
1110
80
54
9
29
29
—
7
3.2
1120
80
54
9
42
32
—
7
3.2
1210
100
80
11
37
37
—
9
3.2
1220
100
80
11
57
40
—
9
4.5
1230, 1240
100
80
9
65
40
—
9
6
1310
120
87
14
44
44
—
11
4.5
1320
120
87
14
62
46
—
11
4.5
1330, 1340
130
87
11
79
47
—
11
9
1410
140
97
18
55
55
—
11
6
1420
140
97
18
75
57
—
14
6
1430, 1440
160
97
14
92
54
—
14
9
1510
150
112
18
65
65
—
11
9
1520
150
112
22
80
70
—
14
9
1530, 1531, 1540
200
112
18
109
64
—
18
9
1630,1631,1632,1633,1640
280
152
22
145
85
—
22
12
Frame size
Mounting bore
Mounting pitches
Thickness
Technical Data
Macine side
159
Detail dimensions of output shaft safety cover (separate
shipment)
● It may be mounted on either the left or right side.
● Made of plastics
A
D
t
A
E
E
B
E
B
C°
A
t
φP.C.D
B
C°
C°
t
D
D
Fig. 12
Fig. 13
Fig. 14
(mm)
Dimensions
Frame size
03, 07, 17
1010
1110, 1120
1210, 1220, 1230, 1240
1310, 1320, 1330, 1340
1410, 1420, 1430, 1440
1510, 1520, 1521, 1522, 1530, 1531, 1540
1630, 1631, 1632, 1633, 1640
A
10
10
10
21
21
30
30
40
B
72
52
56
59
67
77
90
114
Safety cover
C°
D
t
28
R5
2
45
R3
2
45
R3
2
5
R5
2
5
R5
2
5
R5
2
5
R5
2
5
R5
2
M : Screw size
P : Thread pitch
L : Thread length
P.C.D : Mounting pitch
Note 1: The values are subject to change without notice.
Note 2: No screw is required for safety cover for frame size 03, 07, 17, 1010 and 1120.
Note 3: Contact us when safety covers are required.
160
P.C.D
—
—
—
70
78
88
103
135
N : Q'ty
N
—
—
—
2
2
2
2
2
M✕P✕L
—
—
—
M3✕0.5✕6
M3✕0.5✕6
M3✕0.5✕6
M3✕0.5✕6
M3✕0.8✕10
Output shaft end
E
25
25
30
40
45
55
65
95
Fig.
13
12
14
Detail dimensions of output shaft (X1, J1)
R3
b
Ｄ2
S
t
h
R2
R1
D1
Dimensions
Frame size
D1
01
10
03
15
05
12
07
15
15
15
17
18
1120
18
1220, 1230
22
1320, 1330
28
1420, 1430
32
1520, 1530, 1531
40
Tolerance
(h6)
0
-0.009
0
-0.011
0
-0.011
0
-0.011
0
-0.011
0
-0.011
0
-0.011
0
-0.013
0
-0.013
0
-0.016
0
-0.016
R
S
R1
t
29
—
—
2.5
31
—
—
3
29
—
—
2.5
31
—
—
3
31
—
—
3
31
—
—
3.5
28
M6
12
3.5
36
M6
12
3.5
42
M8
16
4
58
M8
16
5
82
M10
18
5
h
Tolerance
Tolerance b (Key)
(Key)
(h9)
+0.1
0
4
4
0
-0.030
+0.1
0
5
5
0
-0.030
+0.1
0
4
4
0
-0.030
+0.1
0
5
5
0
-0.030
+0.1
0
5
5
0
-0.030
+0.1
0
6
6
0
-0.030
+0.1
0
6
6
0
-0.030
+0.1
0
6
6
0
-0.030
+0.2
0
8
7
0
-0.036
+0.2
0
10
8
0
-0.036
+0.2
0
12
8
0
-0.043
R2
Tolerance (Key)
0
22
-0.030
0
22
-0.030
0
22
-0.030
0
22
-0.030
0
22
-0.030
0
22
-0.030
0
22
-0.030
0
32
-0.030
0
35
-0.090
0
50
-0.090
0
70
-0.090
R3
D2
25
25
25
25
25
25
25
25
25
25
25
25
25
25
35
30
39
35
55
45
76
55
Technical Data
Note: Keyway dimensions in accordance with JIS B 1301-1996 parallel keyway (Normal Grade).
Name plate
1Model name of
gear motor
(refer to page 15)
MODEL
2Reduction ratio
· Input power
· Input features
4Motor type
R
RATIO
1
2
kW
VOLTS
Hz
M.AMP
r/min
B.AMP
SERIAL NO.
P φ
5Brake type
TYPE 4
5
FRAME
M/B INS.CLASS
TIME RATING
JISC4004 JP
B.TORQUE
N •m
· Brake features
3
JAPAN
AM446516
3Manufacturing
serial No.
161
Motor characteristics
1. 3-phase motor characteristics
(1) Non-explosion Proof
4 poles
Pole
Motor
frame
size
Reducer
frame
size
Power
F-50S
01#,03#
0.015
0.11
250
240
0.31 1350
0.11
319
319
0.37
1680
0.11
275
260
0.32 1360
F-50M
01#,03#
0.025
0.16
232
221
0.41 1330
0.17
279
272
0.54
1670
0.16
259
248
0.51 1350
F-50L
05#, 07#
0.04
0.23
201
200
0.61 1260
0.24
248
248
0.74
1630
0.23
220
219
0.63 1290
F-56S
17#, 1240#
0.04
0.26
217
215
0.80 1400
0.28
274
266
0.90
1710
0.27
239
242
0.80 1410
F-50L
07#
0.06
0.35
150
148
0.80 1200
0.35
197
197
0.92
1590
0.35
165
164
0.81 1230
F-56M
17#, 1240# 0.06
0.37
208
211
1.1
1380
0.39
268
261
1.4
1690
0.38
229
236
1.2
1390
F-56L
15#, 17#, 1240# 0.09
0.55
214
223
1.7
1370
0.57
269
271
2.1
1690
0.56
235
251
1.8
1380
200V-50Hz
220V-60Hz
220V-50Hz
Power
230V-50Hz
Speed
(r/min)
220V-60Hz
Output Full load Largest Starting Starting Speed Full load Largest Starting Starting Speed Full load Largest Starting Starting
power current torque torque current (r/min) current torque torque current (r/min) current torque torque current
(A)
(%)
(%)
(A)
(A)
(%)
(%)
(A)
(A)
(kW)
(A)
(%)
(%)
Speed
(r/min)
F-63S
0.1
0.60
235
230
2.3
1420
0.62
261
261
2.3
1430
0.53
220
202
2.1
1700
F-63M
0.2
1.0
210
206
3.8
1410
1.0
231
236
4.0
1420
0.95
186
191
3.5
1690
F-71M
0.25
1.6
332
334
7.3
1460
1.8
365
379
7.8
1460
1.4
311
287
6.6
1750
F-71M
0.4
2.0
200
201
7.3
1410
2.1
221
229
7.8
1420
1.8
188
185
6.6
1680
F-80S
0.55
2.4
182
206
9.2
1410
2.4
200
225
9.6
1420
2.3
164
166
8.6
1680
F-80M
0.75
3.3
211
193
13.1
1420
3.3
219
215
13.8
1430
3.1
189
180
12.3
1720
F-90S
1.1
4.7
215
200
21.7
1420
4.6
236
223
22.8
1420
4.4
189
170
19.9
1690
F-90L
1.5
6.1
204
192
27.9
1420
6.0
228
224
28.9
1430
5.7
196
175
25.5
1700
F-100L
2.2
8.7
203
213
42.1
1420
8.3
231
255
45.0
1430
8.1
207
185
38.0
1690
F-112S
3.0
11.2
205
213
61
1420 11.1
224
237
64
1420 10.8
189
155
54
1690
F-112M
3.7
13.4
219
218
80
1410 13.0
231
236
81
1420 12.9
207
178
70
1700
Motor
frame
size
Power
4 poles
Pole
380V-50Hz
400V-50Hz
415V-50Hz
Output Full load Largest Starting Starting Speed Full load Largest Starting Starting Speed Full load Largest Starting Starting
power current torque torque current (r/min) current torque torque current (r/min) current torque torque current
(A)
(%)
(%)
(A)
(%)
(%)
(A)
(kW)
(A)
(A)
(%)
(%)
(A)
Speed
(r/min)
F-63S
0.1
0.34
235
230
1.3
1420
0.36
261
261
1.3
1430
0.37
281
286
1.4
1430
F-63M
0.2
0.61
210
206
2.2
1410
0.62
233
236
2.3
1420
0.63
251
260
2.4
1420
F-71M
0.25
0.95
332
334
4.2
1460
1.0
365
379
4.5
1460
1.1
389
413
4.7
1460
F-71M
0.4
1.2
200
201
4.2
1410
1.2
221
229
4.5
1420
1.3
236
250
4.7
1420
F-80S
0.55
1.4
182
206
5.3
1410
1.4
200
225
5.5
1420
1.4
218
248
5.8
1420
F-80M
0.75
1.9
211
193
7.6
1420
1.9
219
215
8.0
1430
2.0
237
232
8.4
1440
F-90S
1.1
2.7
215
200
12.5
1420
2.7
236
223
13.2
1420
2.7
256
243
14.3
1430
F-90L
1.5
3.5
204
192
16.1
1420
3.5
228
224
17.1
1430
3.6
242
236
17.8
1430
F-100L
2.2
5.0
203
213
24.3
1420
4.8
231
255
26.0
1430
5.0
240
263
26.8
1430
F-112S
3.0
6.5
205
213
35.1
1420
6.4
224
237
37.0
1420
6.2
241
255
35.7
1420
F-112M
3.7
7.8
219
218
45.9
1410
7.5
231
236
46.9
1420
7.7
259
269
51
1430
F-132S
5.5
11.3
215
227
69.0
1410 11.1
237
256
73
1420 11.0
256
281
76
1430
*The values shown in the above tables are subject to change without notice. Contact us for confirmed values.
162
Full load Largest Starting Starting
current torque torque current
(A)
(%)
(%)
(A)
4 poles
Pole
Motor
frame
size
230V-50Hz
Output Full load Largest Starting Starting Speed Full load Largest Starting Starting Speed
power current torque torque current (r/min) current torque torque current (r/min)
(kW)
(A)
(%)
(%)
(A)
(A)
(%)
(%)
(A)
Pole
4 poles
Power
440V-60Hz
Output Full load Largest Starting Starting Speed
power current torque torque current (r/min)
(A)
(kW)
(%)
(%)
(A)
F-63S
0.1
0.32
300
289
1.4
1730
F-63M
0.2
0.54
268
266
2.4
1720
F-71M
0.25
0.87
420
429
4.6
1780
F-71M
0.4
1.0
256
262
4.6
1730
F-80S
0.55
1.2
224
240
5.9
1720
F-80M
0.75
1.7
247
242
8.4
1740
F-90S
1.1
2.3
257
246
13.6
1720
F-90L
1.5
3.0
250
243
17.5
1740
F-100L
2.2
4.2
248
260
26.2
1720
F-112S
3.0
5.5
238
225
27.0
1720
F-112M
3.7
6.6
246
238
46.4
1720
F-132S
5.5
9.6
254
263
73
1720
(2) Increased safety motors
Increased safety motors conform to eG3
of Japanese Industrial Standards (JIS).
a. 200V class
Motor
frame
size
4 poles
Pole
200V-50Hz
Power
200V-60Hz
Output Full load Largest Starting Starting Speed
power current torque torque current (r/min)
(%)
(kW)
(A)
(A)
(%)
220V-60Hz
Full load Largest Starting Starting
current torque torque current
(%)
(%)
(A)
(A)
load Largest Starting Starting
Speed Full
torque torque current
(r/min) current
(A)
(%)
(%)
(A)
Speed
(r/min)
F-63S
F-63M
0.1
0.69
274
281
2.7
1430
0.60
255
245
2.5
1710
0.62
311
297
2.8
1730
0.2
1.2
238
233
4.6
1420
1.1
223
207
4.2
1700
1.1
273
250
4.8
1720
F-71M
F-80M
0.4
2.3
221
237
9.1
1410
2.0
203
210
8.3
1700
2.0
249
257
9.4
1730
0.75
3.9
219
215
16.0
1430
3.4
203
190
15.1
1730
3.3
247
242
16.8
1740
F-90L
1.5
7.0
228
224
34.1
1430
6.3
206
192
31.2
1720
6.0
250
243
34.9
1740
F-100L
F-112M
2.2
9.6
231
255
52
1430
8.8
204
204
46.9
1710
8.3
248
260
52
1720
3.7
15.1
231
236
94
1420
14.2
202
188
83
1700
13.1
246
238
93
1720
F-132S
5.5
22.9
243
286
158
1420
21.1
209
229
139
1700
19.7
254
291
156
1720
b. 400V class
Motor
frame
size
F-63S
4 poles
Pole
Power
400V-50Hz
400V-60Hz
440V-60Hz
Output Full load Largest Starting Starting Speed Full load Largest Starting Starting
power current torque torque current (r/min) current torque torque current
(%)
(%)
(%)
(A)
(A)
(A)
(kW)
(A)
(%)
load Largest Starting Starting
Speed Full
torque torque current
(r/min) current
(%)
(A)
(A)
(%)
Speed
(r/min)
0.1
1710
1730
0.36
261
261
1.3
1430
0.31
246
224
1.2
0.32
300
289
1.4
F-63M
0.2
0.62
233
236
2.3
1420
0.54
219
202
2.1
1700
0.54
268
266
2.4
1720
F-71M
0.4
1.2
221
229
4.5
1420
1.0
209
201
4.1
1700
1.0
256
262
4.6
1730
F-80M
0.75
1.9
219
215
8.0
1430
1.7
203
190
7.6
1730
1.7
247
242
8.4
1740
F-90L
1.5
3.5
228
224
17.1
1430
3.1
206
192
15.6
1720
3.0
250
243
17.5
1740
F-100L
F-112M
2.2
4.8
231
255
26.0
1430
4.4
204
204
23.5
1710
4.2
248
260
26.2
1720
3.7
7.5
231
236
46.9
1420
7.1
202
188
41.4
1700
6.6
246
238
46.4
1720
F-132S
5.5
11.4
233
286
79
1420
10.5
209
229
70
1700
9.9
254
291
78
1720
Technical Data
Motor
frame
size
*The values shown in the above tables are subject to change without notice. Contact us for confirmed values.
163
Motor characteristics
2. Single-phase motor characteristics
a. Induction motors
4 poles
Pole
Motor
frame
size
Reducer
frame
size
FS-50S
FS-50M
FS-50L
FS-56S
FS-56M
FS-56L
FS-63M
FS-71M
FS-80M
01#, 03#
01#, 03#
05#, 07#
17#, 1240#
15#,17#,1240#
15#,17#,1240#
—
—
—
230V-50Hz
Power
Output
power
(kW)
Largest
Starting
Starting
Full load
current (A) torque (%) torque (%) current (A)
Speed
(r/min)
0.015
0.18
225
115
0.37
1390
0.025
0.23
145
82
0.38
1320
0.04
0.36
131
81
0.53
1300
0.04
0.32
206
105
0.85
1380
0.06
0.46
166
83
1.1
1330
0.09
0.70
172
96
1.5
1360
0.1
1.1
254
254
4.8
1450
0.2
1.6
201
224
6.9
1440
0.4
2.9
219
205
15.1
1450
b. Reversible motors
Motor
frame
size
Reducer
frame
size
FS-50S
FS-50M
FS-50L
FS-56S
FS-56M
FS-56L
01#, 03#
01#, 03#
05#, 07#
17#, 1240#
15#,17#,1240#
15#,17#,1240#
Pole
4 poles
4 poles
Power
100V-50Hz
100V-60Hz
Output
power
(kW)
Largest
Starting
Starting
Full load
current (A) torque (%) torque (%) current (A)
Speed
(r/min)
Largest
Starting
Starting
Full load
current (A) torque (%) torque (%) current (A)
0.015
0.41
175
104
0.69
1290
0.38
158
103
0.67
1630
0.025
0.57
162
105
0.92
1310
0.66
190
133
0.93
1620
0.04
0.84
136
89
1.22
1270
0.97
145
106
1.24
1580
0.04
0.78
217
114
1.9
1370
0.92
240
150
1.8
1670
0.06
1.1
195
112
2.5
1370
1.4
220
140
2.4
1660
0.09
1.6
185
104
3.5
1360
2.10
206
138
3.3
1660
*The values shown in the above tables are subject to change without notice. Contact us for confirmed values.
3. Characteristics of motors for inverters
4 poles
4 poles
4 poles
Pole
Motor
220V-60Hz
380V-60Hz
415V-60Hz
Power
frame
Frequency Voltage Full load Speed Frequency Voltage Full load Speed Frequency Voltage Full load Speed
size Output
power
current
current
current
(kW)
FA63S
FA63M
FA71M
FA80M
FA90L
FA100L
FA112M
0.1
0.2
0.4
0.75
1.5
2.2
3.7
(Hz)
(V)
(Hz)
(V)
(Hz)
(V)
1765
60
380
(A)
0.38
(r/min)
220
(A)
0.85
(r/min)
60
1755
60
415
(A)
0.40
6
34
0.75
120
6
68
0.37
125
6
68
0.37
125
60
220
1.6
1760
60
380
0.69
1750
60
415
0.75
1760
(r/min)
1760
6
34
1.5
130
6
68
0.75
130
6
68
0.75
130
60
220
2.4
1745
60
380
1.1
1725
60
415
1.1
1740
6
35
2.2
115
6
70
1.1
115
6
70
1.1
115
60
220
4.0
1755
60
380
1.9
1735
60
415
1.9
1745
6
31
3.9
120
6
62
1.9
120
6
62
1.9
120
60
220
6.4
1735
60
380
3.3
1705
60
415
3.1
1725
6
33
6.5
105
6
66
3.2
110
6
66
3.2
110
60
220
9.1
1755
60
380
4.7
1740
60
415
4.4
1750
6
31
9.3
140
6
62
4.6
135
6
62
4.6
135
60
220
14.0
1750
60
380
7.7
1730
60
415
7.2
1745
6
30
14.8
125
6
60
7.4
120
6
60
7.4
120
*The values shown in the above tables are subject to change without notice.
Contact us for confirmed values.
164
Speed
(r/min)
Dimensions of a terminal box
3-phase
Standard motors 0.1kW~5.5kW and motors for inverters 0.1~3.7kW
(mm)
S0
T0
T/
U/
62
U0
S/
63
125
2-M25✕P1.5
Single-phase
0.1kW~0.4kW
Electronic governor switch
Ａ
T
23
Ｌ
Ｅ
(mm)
kW
RNFM and RNHM Series of solid shaft
type do not come with electronic
governor switch.
0.1
0.2
0.4
With/without brake
A
116
116
109
E
L
91.5 55.5
91.5 55.5
129.5 75.5
T
72
72
69
3-phase, Single-phase
15W~90W
１ ２ ３
Ｕ Ｖ Ｗ
｜ ｜ ｜
(mm)
White
B B
Red
62
Black
Technical Data
Terminal box with a terminal plate (option)Terminal boxes are optional for 15-90W
M3.5
81.5
Terminal Plate
Reversible motors Induction motors
Applicable motors
5
12.
28
49.5
38
13.5
32
Without brake
With brake
Without brake
165
Mounting direction of a terminal box
Mounting direction of a terminal box may be changed by 90˚. Specify a direction according to the Figs below. The
direction must be changed by Sumitomo.
(Terminal boxes are optional for 15-90W. Refer to the outline drawings for lead wire opening direction. The direction
cannot be changed after shipment.)
(1) 3-phase (Standard motors and motors for inverters)
(N35)
Up
Hollow shaft type
Left
(N33)
(RNYM series)
Right
(N34)
Standard
Up
Up
(N35)
(N35)
Solid shaft
Flange mount type
Standard
(RNFM series)
Down
(N36)
Up
(N35)
Up
(RNHM series)
(N35)
(N34)
Right Left
(N33)
Standard
Down
L type
Up
Standard
(N35)
Right
(N34)
Standard
Down
Down
(N36)
R type
(N36)
Standard
Down
R type (N36)
L type
Solid shaft
Foot mount type
Left
(N34)
Right
(N34)
T type
(N36)
The directions indicated as above are viewed from the opposite side of motor fan cover.
Arrows indicate lead wire opening direction.
(2) Single-phase
(N35)
Up
Hollow shaft type
Left
(N33)
(RNYM series)
Right
(N34)
Standard
(N35)
Solid shaft
Flange mount type
(N35)
Up
Up
Right
(N34)
Standard
(RNFM series)
Left
(N37)
Down
Down
R type
L type
(N36)
(N36)
(N35)
(N35)
(N35)
Up
Up
Up
Solid shaft
Foot mount type
(RNHM series)
Right Left
(N34) (N33)
Standard
Down
L type
(N36)
Down
Standard
Right
Standard
(N34)
Down
(N36)
R type
The directions indicated as above are viewed from the opposite side of motor fan cover.
Arrows indicate lead wire opening direction.
166
Standard
T type
(N36)
Specifications and construction of built-in
(1) Specifications
a. Brake specifications of 3-phase motors (standard)
Brake
type
SB-004
FB-003
SB-004
Output
power
(4 poles)
15W
25W
40W
40W
60W
60W
90W
FB-01A1 90W
FB-01A 0.1kW
FB-02A1 0.2kW
0.25kW
FB-05A1
0.4kW
0.55kW
FB-1B
0.75kW
1.1kW
FB-2B1
1.5kW
FB-3B
2.2kW
3.0kW
FB-5B
3.7kW
FB-8B
5.5kW
FB-005
Reducer Standard torque Moment of inertia
frame
(1✕10-4kg·m2)
(Nm)
size
01#, 03#
01#, 03#
0.4
0.135
05#, 07#
1.1
0.3
17#
0.135
07#
0.4
1.2
17#
0.5
1.5
15#, 17#,
3.6
1.0
361#, 36#
3.6
1.0
—
5.6
2.0
—
Total braking energy
Motion delay (Sec)
(✕107J)
Standard control Quick braking
circuit
circuit
Brake current (A)
220V50Hz 230V50Hz 220V60Hz 380V50Hz 400V50Hz 415V50Hz 440V60Hz
1.1
0.1~0.2 0.005~0.015
0.06
—
0.05
—
—
—
—
1.0
1.1
0.1~0.12 0.05~0.06
0.1~0.2 0.005~0.015
0.03
0.06
—
—
0.04
0.05
—
—
—
—
—
—
—
—
1.0
0.1~0.12 0.05~0.06
0.03
—
0.04
—
—
—
—
12
12
12
0.15~0.2 0.015~0.02
0.08
0.08
0.1
0.08
0.08
0.1
0.08
0.08
0.1
0.03
0.04
0.04
0.04
0.1~0.15 0.01~0.015
0.1
0.1
0.1
0.1
0.1
0.1
0.3
0.3
0.3
0.3
0.3
0.3
0.6
0.6
0.6
—
—
—
0.15~0.2 0.015~0.02
—
4.0
6.9
12
—
7.5
13
33
—
15
24
38
—
22
38
45
0.3~0.4
—
37
98
235
0.4~0.5
—
55
128
235
0.3~0.4
0.2~0.3
0.01~0.02
0.01~0.02
Brakes are available only for
200V class.
Refer to the brake current at
200V classs
0.3
0.3
0.3
0.3
b. Brake specifications of 3-phase motors (water-proof)
Brake
type
SB-004
FB-003
SB-004
FB-005
Output
power
(4 poles)
15W
25W
40W
40W
60W
60W
90W
Reducer Standard torque Moment of inertia
frame
(1✕10-4kg·m2)
(Nm)
size
01#, 03#
01#, 03#
0.4
0.135
05#, 07#
17#
1.1
0.3
07#
0.135
0.4
17#
1.2
0.5
15#, 17#,
1.5
Total braking energy
(✕107J)
Motion delay (Sec)
Standard control Quick braking
circuit
circuit
Brake current (A)
220V50Hz 220V60Hz 230V50Hz
1.1
0.1~0.2
0.005~0.015
0.05
0.05
—
1.0
1.1
0.1~0.12
0.1~0.2
0.05~0.06
0.005~0.015
0.04
0.05
0.04
0.05
—
—
1.0
0.1~0.12
0.05~0.06
0.04
0.04
—
Brake
type
SB-004
FB-003
FB-005
Output
power
(4 poles)
15W
25W
40W
40W
60W
90W
FB-01A1 0.1kW
FB-02A1 0.2kW
FB-1B 0.4kW
Reducer Standard torque Moment of inertia
frame
(1✕10-4kg·m2)
(Nm)
size
01#, 03#
01#, 03#
0.4
0.135
05#, 07#
1.4
17#
0.3
1.2
15#, 17#
0.5
1.5
15#, 17#
5.6
—
1.0
6.9
2.0
—
13
—
4.0
Total braking energy
Motion delay (Sec)
Quick braking
circuit
(✕10 J)
Standard control Quick braking
circuit
circuit
230V50Hz
7
1.1
0.1~0.2
0.005~0.015
—
1.0
0.1~0.12
0.05~0.06
—
0.15~0.2
0.015~0.02
0.2
0.3~0.4
0.01~0.02
0.2
12
12
33
Technical Data
c. Brake specifications of single-phase motors (standard)
167
Specifications and construction of built-in brake
d. Brake specifications of single-phase motors (water-proof)
Output
power
(4 poles)
Reducer Standard torque Moment of inertia
frame
(1✕10-4kg·m2)
(Nm)
size
15W 01#, 03#
0.4
0.074
25W 01#, 03#
40W 05#, 07#
Brake
type
SB-004
Motion delay (Sec)
Total braking energy
(✕107J)
Standard control Quick braking
circuit
circuit
1.1
0.1~0.2
Brake current (A)
230V50Hz
0.005~0.015
—
e. Brake specifications of 3-phase motors for inverter
Output Standard torque Moment of inertia Total braking energy
power
(1✕10-4kg·m2)
(Nm)
(✕107J)
(4 poles)
Brake
type
FB-02A2
FB-05A1
FB-1B
FB-2B1
FB-3B
FB-5B
FB-8B
0.1kW
0.2kW
0.4kW
0.75kW
1.5kW
2.2kW
3.7kW
2.0
4.0
7.5
15
22
37
55
5.6
6.9
13
24
38
98
128
12
12
33
38
45
235
235
Motion delay (Sec)
Standard control Quick braking
circuit
circuit
0.15~0.2
0.03~0.07
0.1~0.15
0.15~0.2
0.2~0.25
0.1~0.15
0.015~0.02
0.01~0.015
0.01~0.02
0.01~0.02
Brake Current (A)
200V60Hz 380V60Hz 415V60Hz
0.1
0.1
Brakes are available
0.1
only for 200V class.
0.3
Refer to the brake
0.3
current at 200V class
0.6
—
. Low-noise type FB brake is available optionally.
(FB-01A2-FB-8B)
. FB brake is direct current and spring braking type
(non-electrical braking).
. The above standard torque indicate the value of
dynamic friction torque.
. Continuous time rating for Motor as well as brake.
. Non-asbestos lining is used for brake.
. Mechanical life time of brake is as long as 2 million times under normal
usage conditions.
. Rectifiers of FB brake is built in the brake for 40-90W and in the terminal
box for 0.1kW and above. Rectifiers of SB brake is supplied separately.
. To improve the elevating device and stopping accuracy, use the quick
braking circuit.
Output power of a rectifier in
3-phase brake
Input voltage Output voltage
AC200V
DC90V
AC220V
DC99V
AC400V
DC180V
AC440V
DC198V
Why quick braking circuit shortens braking time.
See Fig 15 and Fig 16 for differences between standard braking circuit and quick braking circuit.
See Fig 17 and Fig 18 for current curves of standard braking circuit and quick braking circuit.
V
V
Circuit in the rectifier
Current
Current
tb
U
W
W
U
2
Remaining
current
2
(3)
4
Fig. 15 standard circuit
OFF
1
Time
OFF
Time
(3)
M
Fig. 16 quick braking circuit
Fig. 17 current curve of
standard braking circuit
In the standard circuit as Fig 15, some current remains after the power
is turned off due to the saved energy in the inductance L of brake coil.
The current curve is shown in the Fig. 17.
When it is connected to quick braking circuit as the Fig 16 and S is
released at the same time, no current remains as there is no closed
168
2
Holding
current
S
N
4
4
M
1
VR
(Varistor)
(3)
N
1
Fig. 18 current curve
or quick braking
circuit
circuit with the brake coil. (See the Fig. 18)
Therefore, it shortens the braking time by tb in the Fig 17. Quick
braking circuit is to release all current by ON/OFF of brake coil at the
same time with power ON/OFF.
(VR varistor must be used to protect the rectifier and connection S.)
2. Construction
Fig. 19 SB-004 (Indoor) (15W~60W×4 Poles)
Fig. 20 SB-004 (water-proof) (15W~90W×4 Poles)
G
G
Part No.
1
2
3
4
Description
Assembling bolt
Stationary core
Armature plate
Lining with fan
8
9
10
11
Set bolt
Retaining ring
Cover
Torque spring
1
2
3
4
Description
Assembling bolt
Stationary core
Armature plate
Lining with fan
8
9
10
11
Set bolt
Retaining ring
Cover
Torque spring
Fig. 22 FB-01A1,02A1,05A1 (0.1kW ~ 0.4kW × 4
Poles) (FB-01A1 Without Fan)
Technical Data
Fig. 21 FB-003,005 (40W~90W×4 Poles)
Part No.
G
Part No.
Part No.
1
2
3
4
5
6
7
Description
Assembling bolt
Stationary core
Brake lining
Armature plate
Leaf spring
Rectifier
Stationary core
8
9
10
11
12
13
14
15
Cover
Fan (only for single-phase 60 and 90W)
Gap adjusting shim
Torque spring
Stud bolt
Supporting spring
Boss
Boss set bolt
1
2
3
4
5
6
7
Description
Stationary core
Spacer
Brake lining
Assembling bolt
Boss
Shaft retaining C-ring
Cove
8
9
10
11
12
13
14
15
Fan (except for 0.1kw ×4 poles)
Leaf spring
Fixed plate
Armature plate
Spring
Electromagnetic coil
Ball bearing
Motor shaft
*Brake releasing unit is optionally available.
169
Specifications and construction of built-in brake
Fig.23 FB-1B,2B1,3B (0.75~2.2kW×4 poles)
Fig. 24 FB-5B, 8B (3.0~5.5kW×4 poles)
G
G
Part No.
1
2
3
4
5
6
7
8
9
10
Description
Stationary core
Release fitting
Manual release protection spacer
Brake release bolt
Spacer
Gap adjusting shim
Assembling bolt
Brake lining
Leaf spring
Boss
11
12
13
14
15
16
17
18
19
20
Shaft retaining C-ring
Cover
Fan set bolt
Fan
Fixed plate
Armature plate
Spring
Electromagnetic coil
Ball bearing
Motor shaft
Part No.
1
2
3
4
5
6
7
8
9
10
Description
Stationary core
Release fitting
Stud bolt
Adjusting washer
Manual release protection spacer
Brake release bolt
Spring washer
Gap adjusting nut
Brake lining
Boss
Manual releasing of FB brake
To release the brake manually, follow the steps as below.
11
12
13
14
15
16
17
18
19
20
21
Shaft retaining C-ring
Cover
Spring pin
Fan
Leaf spring
Fixed plate
Armature plate
Spring
Electromagnetic coil
Ball bearing
Motor shaft
Brake releasing bolt
Brake releasing bolt
(1) Release two of the brake releasing bolts diagonally and remove the
spacer. Then put back the bolts with a hexagon wrench until the brake
will be released. Carefully screw the releasing bolts as the brake is
being released.
(2) After the brake is released, put back the spacer in place for safety.
Spacer
Note that brake releasing unit is optional for FB-01A1, FB-02A1 and FB05A1 while it is supplied as standard specifications to FB-1B and
above.
Released
170
In operation
Wiring diagram
1. Single-phase motor
Wiring diagram for standard motors
15W~90W
Operation in one direction
100V Class
R
200V Class
S
MC
MC
OLR
OLR
SW
Black
Black
White
Terminal
box
Brown
Control
panel
C
Terminal
box
Brown
C
White
SW
Control
panel
Motor
Operating in both directions
S
R
Motor
Note 1: Turn the switch SW to change the Note 1: Turn the switch SW to change the
current to the opposite direction.
current to the opposite direction.
When instant switching is required,
When instant switching is required,
use a reversible motor.
use reversible motor.
Note 2: Capacitor attached to the motor must Note 2: Capacitor attached to the motor must
be connected. (Refer to page 164 for
be connected. (Refer to page 164 for
a capacitor.)
a capacitor.)
Note 3: Single-phase 200V class motors for
15–90W are available by request.
0.1kW~0.4kW
R
S
MC
MC
OLR
OLR
S
Control
panel
Control
panel
Terminal
box
V1
U1
U2
V2
X
Y
Motor
Terminal
box
U1
V2
U 2 X V1 Y
Motor
R S
R
OLR
S
Normal
Reverse
Normal
OLR
Reverse
Operating in both directions
Operation in one direction
R
200V Class
Technical Data
100V Class
Control
panel
U1 V1 X Y
U2 V2
Motor
Terminal
box
Control
panel
U1 V2 X Y
Motor
V1
U2
Terminal
box
Note: When operating in the reversed direction, exchange X
and Y in the above diagrams .
MC: Electromagnetic contactor, OLR: Overload relay (thermal
relay), SW: switch and C: capacitor are not supplied by
Sumitomo.
171
Wiring diagram
Specifications and dimensions of capacitors for 15-90W single-phase motor
4.3
10
20
4
H
95
T
Vinyl wire UL (1015)
0.53mm2 (black)
E
W
Motor Capacitor
voltage voltage
D
Motor Input power Frame size of
reducer
(W)
type
Induction
100V
220V
Reversible
Induction
200V
440V
Reversible
Note: Contact us for 200V motors.
172
15
25
40
40
60
90
15
25
40
40
60
90
40
60
90
40
60
90
01#,03#
01#,03#
05#,07#
17#, 1240#
17#, 1240#
15#,17#, 1240#
01#,03#
01#,03#
05#,07#
17#, 1240#
17#, 1240#
15#,17#, 1240#
17#, 1240#
17#, 1240#
15#,17#, 1240#
17#, 1240#
17#, 1240#
15#,17#
Capacitor
capacity
(μF)
5
7
12
14
18
25
6
10
14
16
22
32
3.5
4.5
6.5
4
5.5
8
apacitor dimension (mm)
W
H
T
D
E
31
37
48
58
58
58
37
48
58
58
58
58
58
58
58
58
58
58
27
27
29
31
31
37
27
29
31
31
37
41
35
37
41
35
37
50
17
18
19
21
21
23.5
18
19
21
21
23.5
29
22
23.5
29
22
23.5
35
27
28
29
31
31
38.5
28
29
31
31
38.5
44
32
38.5
44
32
38.5
50
4.5
4.5
4.5
4.5
4.5
7
4.5
4.5
4.5
4.5
7
7
4.5
7
7
4.5
7
7
2. Single-phase motor with brake
a.Connections when operating in one direction
· For the elevating device or to improve stopping accuracy, use the quick braking
circuit.
· Connection capacity for quick braking circuit is recommended to have more than five
times of braking capacity (direct current coil load) of the brake current.
15W~40W (SB-004)
For frame size #01, 03, 05 and 07
R
S
R
Rectifier
S
Rectifier
MC
1 2 4
1 2 4
OLR
OLR
SW
Control
panel
C
Control
panel
SW
C
S
R
1 2 4
Yellow
Black
Motor
Rectifier
MC
Brown
White
Brake
Motor
Yellow
Motor
Grey
Black
Blue
Grey
Motor
R
Brake
S
Rectifier
MC
1 2 4
VR
VR
OLR
OLR
SW
Control
panel
SW
Control
panel
C
Motor
Brake
Motor
Yellow
Yellow
Brown
Black
Motor
White
Grey
Grey
Motor
Blue
Black
C
White
Quick braking circuit
200V Class
MC
White
Standard braking circuit
100V Class
Brake
40~90W (FB-003~FB-005)
For frame size #15 and 17
R
S
S
MC
MC
OLR
OLR
SW
SW
Control
panel
C
Control
panel
C
Motor
S
R
Yellow
Yellow
Brown
Brake
Motor
Brake
Motor
Black
White
Yellow
Blue
Yellow
Black
Motor
R
MC
OLR
OLR
SW
Control
panel
Control
panel
C
Motor
Brake
Motor
Yellow
Yellow
Brown
Black
White
Yellow
Yellow
Blue
Black
Motor
Motor
MC: Electromagnetic contactor, OLR: Overload
relay (thermal relay), SW: switch, VR: varistor and
C: capacitor are not supplied by Sumitomo.
S
SW
C
Note 1: A rectifier is supplied separately for motors
of 15~40W for frame size #01, 03, 05 and
07.
Note 2:A rectifier is built in the brake of motors of
40~90W for frame size #15 and 17. (FB003~005)
Note 3: Turn the switch SW to change the current
of 15~90W motors to the opposite
direction. When instant switching is
required, use a reversible motor.
Note 4: Contact us for motors of 40~90W 200V.
Note 5: Capacitor
Use the capacitor attached to the product.
MC
White
Quick braking circuit
200V Class
Brake
Technical Data
R
White
Standard braking circuit
100V Class
Capacity of varistor (VR)
Input power
Rated voltage of varistor
Voltage of varistor
Rated capacity of motor
AC100V, 200V
AC260V~300V
430V~470V
0.2Watt or more
Varistor is optionally available at Sumitomo.
173
Wiring diagram
0.1kW~0.2kW (FB-01A1~FB-02A1)
Standard braking circuit
200V Class
R
S
MC
Control
panel
OLR
Terminal
box
U1
U2 X V1
V2
Y
4
M N
Rectifier
Brake
Motor
R
Quick braking circuit
1 2
S
MC
VR
Control
panel
OLR
Terminal
box
U1
U2 X V1
V2
Y
1 2
4
M N
Rectifier
Brake
Motor
0.4kW (FB-1B)
200V Class
Standard braking circuit
R
S
MC
Control
panel
OLR
Terminal
box
U1
U2 X V1
1 2 3 4
M N
Rectifier
Brake
Motor
R
Quick braking circuit
V2
Y
Note: When reverse 0.1~0.4kW motor, change X
to Y (or Y to X) after the motor has stopped.
S
MC
MC: Electromagnetic contactor, OLR: Overload
relay (thermal relay), SW: switch and VR: varistor
are not supplied by Sumitomo.
VR
Control
panel
OLR
Terminal
box
U1
U2 X V1
Motor
V2
Y
1 23 4
M N
Rectifier
Brake
Capacity of varistor (VR)
Input power
Rated voltage of varistor
Voltage of varistor
Rated
capacity of
varistor
FB-01A1, 02A1
FB-1B
AC100V, 200V
AC260V~300V
430V~470V
0.2Watt or more
0.4Watt or more
Varistor is optionally available at Sumitomo.
174
b. Connections when operating in both directions (0.1~0.4kW single-motor)
0.1kW~0.2kW (FB-01A1~FB-02A1)
Standard
R S
OLR
U1 V2 X Y V1
Motor U2
12 4
M N
Rectifier
Brake
R S
OLR
Standard
Reverse
Terminal Control
box
panel
Reverse
Quick braking circuit
Terminal Control
box
panel
Standard braking circuit
200V Class
R S
VR
U1 V2 X Y V1 1 2 4
Motor U2 Rectifier
M N
Brake
0.4kW (FB-1B)
U1 V2 X Y V1
U2
Motor
1234
M N
Rectifier
Brake
Technical Data
Standard
Terminal Control
box
panel Reverse
R S
OLR
R S
OLR
Standard
Quick braking circuit
Terminal Control
box
panel Reverse
Standard braking circuit
200V Class
R S
U1 V2 X Y V1 1 2 3 4
Motor U2 Rectifier
VR
M N
Brake
•
Reversible electromagnetic contactor and
OLR: Overload relay are not supplied by
Sumitomo. VR: varistor is optionally available
at Sumitomo.
175
Wiring diagram
3. 3-phase motors
Wiring diagram for standard motors
15–90W
0.1–3.7kW
Operation one direction
R S T
L1 L2 L3
MC
Forward
W2 U2 V2
Motor
L1 L2 L3
Forward
L1 L2 L3
Reverse
Control panel
Control panel
Motor
Terminal Box
Black
Red
White
U1 V1 W1
W2 U2 V2
Motor
Reverse
Forward
U1 V1 W1
Terminal Box
W2 U2 V2
Motor
Note:
MC: Electromagnetic contactor
OLR: Overload relay or thermal relay
These should be furnished by
the customer
Example of wiring
0.1–3.7kW
176
400V Class
0.1–3.7kW
5,5kW
Reverse
Control panel
U1 V1 W1
W2 U2 V2
Motor
Motor
Control panel
Terminal Box
U1 V1 W1
T
S
OLR
Control panel
Terminal Box
Black
Red
White
Motor
Motor
Operation in both direction
MC
OLR
Control panel
200V Class
400V Class
L1 L2 L3
MC
OLR
R
0.1–3.7kW
5,5kW
400V Class
200V Class
400V Class
4. 3-phase motor with brake
a.Connections when operating in one direction
R
S
T
40~90W (FB-003~FB-005) for
frame size #15 and 17
Rectifier
R
MC
1 2 4
S
T
MC
OLR
Control
panel
OLR
Control
panel
Motor
Motor
R
S
Brake
R
S
Black
Yellow
Brake
T
MC
1 2 4
MC
Yellow
Motor
Rectifier
T
White
Red
Yellow
Yellow
Black
Red
White
Motor
VR
OLR
Motor
Yellow
Yellow
Motor
Black
Motor
Red
Control
panel
White
Yellow
Yellow
Brake
Control
panel
Brake
Note 1: A rectifier is supplied separately for
15~40W motors for frame size #01,
03, 05 and 07.
Note 2: A rectifier is built in the brake of
40~90W motors for frame size #15, 17
and 19.
(FB-003~005)
Technical Data
Motor
Black
OLR
White
Red
Quick braking circuit
Standard braking circuit
15~60W(SB-004) for
frame size #01, 03, 05 and 07
177
Wiring diagram
3-Phase Motor with Brake : 0.1kW✕4P–3.7kW✕4P (FB-01A–FB-5B)
200V Class 3 Source with
200V Class FB Brake
Standard braking circuit
L1 L2 L3 (200V Class 3
L1 L2 L3 (200V Class 3
Source)
Source)
MC
MC
OLR
OLR
1
U1 V1 W1
2
Control panel
Control panel
Terminal Box
Terminal Box
4
3
M N
Rectifier
W2 U2 V2
Motor
L1 L2 L3 (200V Class 3
Quick braking circuit
400V Class 3 Source with
200V Class FB Brake
U1 V1 W1
Brake
2
4
3
L1 L2 L3 (400V Class 3
Brake
Source)
VR
MC
VR
M N
Rectifier
W2 U2 V2
Motor
Source)
MC
1
OLR
OLR
U1 V1 W1
1
2
Control panel
Control panel
Terminal Box
Terminal Box
3
M N
4
Rectifier
W2 U2 V2
Motor
Brake
U1 V1 W1
1
2
M N
4
3
Rectifier
W2 U2 V2
Motor
Brake
3-Phase Motor with Brake(Inverter Driven Connection) :
0.1kW✕4P–3.7kW✕4P (FB-01A–FB-5B)
200V Class 3 Source with
200V Class FB Brake
Standard braking circuit
L1 L2 L3 (200V Class 3
Source)
400V Class 3 Source with
200V Class FB Brake
L1 L2 L3 (400V Class 3
L1 N (200V Class 3
Source)
MCB
Source)
MCB
MC
Inverter
U1 V1 W1
Source)
L1 N (200V Class 3
1
2
Control panel
Terminal Box
Terminal Box
U1 V1 W1
4
3
Rectifier
W2 U2 V2
Motor
MC
Inverter
Control panel
Brake
1
2
4
3
M N
Rectifier
W2 U2 V2
Motor
•
Electromagnetic contactor and OLR: Overload
relay are not supplied by Sumitomo.
VR: varistor is optionally available at Sumitomo.
Brake
Brake input power
Source)
L1 L2 L3 (400V Class 3
Quick braking circuit
L1 N (200V Class 3
L1 N (200V Class 3
MCB
VR
VR
AC510V
820V
FB-01A1,02A1,05A1 0.2Watt and above 0.4Watt and above
FB-1B
0.4Watt and above 0.6Watt and above
FB-2B,3B,5B,8B
0.6Watt and above 1.5Watt and above
Inverter
1
2
Control panel
Control panel
Terminal Box
Terminal Box
3
Rectifier
4
M N
Brake
U1 V1 W1
W2 U2 V2
Motor
1
2
3
Rectifier
4
To improve the elevating device and
stopping accuracy, use the quick braking
circuit.
• Connection capacity of quick braking circuit
is recommended to have more than five
times of braking capacity (direct current coil
load) of the brake current shown on the table
in page 159.
•
MC
Inverter
U1 V1 W1
Source)
430V~470V
AC380V~460V
MCB
MC
W2 U2 V2
Motor
178
Source)
Source)
Rated
capacity of
varistor
Varistor voltage
L1 L2 L3 (200V Class 3
AC200V~230V
Rated voltage of varistor AC260~AC300V
M N
Brake
c. Connections when operating a brake motor by an inverter
3-Phase Motor with Brake : 5.5kW✕4P (FB-8B)
400V Class 3 Source with
400V Class FB Brake (Direct Starting Method)
L1 L2 L3 (400V Class
3 Source)
Source)
OLR
MC
MCM
MC
MC
OLR
Control panel
Control panel
Terminal Box
2
1
4
3
M N
Rectifier
L1 L2 L3 (400V Class 3
Brake
Terminal Box
U1V1 W1
OLR
MC
M N
Rectifier
Brake
W2U2 V2
Motor
L1 L2 L3 (400V Class
3 Source)
Source)
1 2 3 4
VR
MCM
For Starting
MC MC
M M
ONON
(Star Connection) MC OFF
MC
ON
After Completion MC M ON
of Loading
MC ON
(Delta Connection) MC
OFF
MC
Y
MC
OLR
Control panel
2
1
Rectifier
W2 U2 V2
Motor
Terminal Box
M N
4
3
Note 1: Refer to instruction manuals and
guide manual of inverter for
interlocking with inverter required
in MC ON/OFF.
Note 2: Connection capacity for quick
braking circuit is recommended to
have more than five times of
braking capacity (direct current coil
load) of the brake current shown
on the table in page 159.
Control panel
Terminal Box
U1 V1 W1
VR
Brake
U1 V1 W1
W2 U2 V2
Motor
1 2 3 4
M N
Rectifier
Brake
3-Phase Motor with Brake (Inverter Driven Connection) :
3.7kW✕4P (FB-8B)
·
400V Class 3 Source with
400V Class FB Brake
Source)
L1 L3 (400V Class 3
Source)
MCB
MC
Inverter
Control panel
Terminal Box
U1 V1 W1
1
2
M N
4
3
Rectifier
W2 U2 V2
Motor
L1 L2 L3 (400V Class 3
Brake
AC200V~230V
AC380V~460V
AC260~AC300V
AC510V
Varistor voltage
430V~470V
820V
FB-01A1,02A1,05A1 0.2Watt and above
0.4Watt and above
FB-1B
0.4Watt and above
0.6Watt and above
FB-2B, 3B, 5B, 8B
0.6Watt and above
1.5Watt and above
Source)
L1 L3 (400V Class 3
Quick braking circuit
Brake input power
Rated voltage of varistor
Rated
capacity of
varistor
Standard braking circuit
L1 L2 L3 (400V Class 3
VR: varistor is optionally available
at Sumitomo.
Technical Data
U1 V1 W1
W2 U2 V2
Motor
Quick braking circuit
For Starting
MC MC
M M
ONON
(Star Connection) MC OFF
MC
ON
After Completion MC M ON
of Loading
MC ON
(Delta Connection) MC
OFF
Y
Standard braking circuit
L1 L2 L3 (400V Class 3
400V Class 3 Source with
400V Class FB Brake (
Starting Method)
Source)
MCB
VR
MC
Inverter
Control panel
Terminal Box
U1 V1 W1
W2 U2 V2
Motor
1
2
3
Rectifier
4
M N
Brake
179
Wiring diagram
b. Connections when operating in both directions
15W-60W (SB-004) for
frame size #01, 03, 05 and 07
Rectifier
OLR
S
T
Standard
Reverse
1 2 4
Control
panel
OLR
Control
panel
Motor
R
S
Brake
T
124
S R
OLR
Reverse
Standard
Reverse
Rectifier
VR
Control
panel
OLR
Motor
Motor
Yellow
Yellow
Black
White
Red
Yellow
Black
White
Red
Yellow
Brake
S R
Control
panel
Motor
Motor
Yellow
Black
Yellow
White
Red
Motor
Brake
R S T
Standard
Yellow
Yellow
Black
White
Motor
Motor
Quick braking circuit
R
Reverse
T
Standard
S
Red
Standard braking circuit
R
40W-90W(FB-003, FB-005) for
frame size #15 and 17
Brake
Note 1: A rectifier is supplied separately for
15W-40W (SB-004) motors for frame
size #01, 03, 05 and 07.
Note 2: A rectifier is built in the brake of 4090W motors for frame size #15 and 17
(FB-003-005)
•
Electromagnetic contactor and OLR: Overload
relay are not supplied by Sumitomo.
VR: varistor is optionally available at Sumitomo.
180
3-Phase Motor with Brake : 0.1kW✕4P–3.7kW✕4P (FB-01A–FB-5B)
(Forward & Reverse Mode Connection)
200V Class 3 Source with
200V Class FB Brake
Forward
Reverse
OLR
OLR
Control panel
U1 V1 W1
1234
Control panel
Terminal Box
Forward
Reverse
L1 L2 L3 (200V Class 3
N
U1 V1 W1
1234
M
Brake
W2 U2 V2
Motor
Rectifier
Brake
M
Rectifier
Source)
L1 L2 L3 (400V Class 3
Forward
FOR REV VR
Control panel
Terminal Box
U1 V1 W1
N
Source)
FOR REV VR
OLR
OLR
W2 U2 V2
Motor
Source)
Reverse
Forward
Terminal Box
W2 U2 V2
Motor
Quick braking circuit
L1 L2 L3 (400V Class 3
Source)
Reverse
Standard braking circuit
L1 L2 L3 (200V Class 3
400V Class 3 Source with
200V Class FB Brake
1234
N
U1 V1 W1
1234
M
Brake
W2 U2 V2
Motor
Rectifier
Brake
M
Rectifier
Control panel
Terminal Box
N
3-Phase Motor with Brake : 5.5kW✕4P (FB-8B)
(Forward & Reverse Mode Connection)
ON
ON
ON
OFF
OLR
MC
Control panel
MC
Terminal Box
Control panel
Terminal Box
U1 V1 W1
1234
M
W2 U2 V2
Motor
Rectifier
Brake
U1 V1 W1 W2 U2 V2
Motor
Source)
(400V Class
L1 L2 L3 3 Source) For Starting
MC MC
M M
ONON
(Star Connection) MC OFF
Reverse
Forward
Reverse
FOR REV VR
1 2 3 4
Rectifier
MC
After Completion MC M
of Loading
MC
(Delta Connection) MC
MCM
W2 U2 V2
Motor
Rectifier
M
MC
MC
FOR. REV. VR
Control panel
Terminal Box
N
Brake
U1 V1 W1 W2 U2 V2
Motor
·
VR: varistor is optionally available
at Sumitomo.
Brake input power
AC200V~230V
Rated voltage of varistor
AC260~AC300V
Varistor voltage
Control panel
Terminal Box
1234
ON
ON
ON
OFF
OLR
OLR
U1 V1 W1
M N
Brake
Y
Forward
N
1 2 3 4
Rectifier
M N
Brake
Rated
capacity of
varistor
MCM
OLR
Note 1: Refer to instruction manuals and
guide manual of inverter for
interlocking with inverter required
in MC ON/OFF.
Note 2: Connection capacity for quick
braking circuit is recommended to
have more than five times of
braking capacity (direct current coil
load) of the brake current shown
on the table in page 159.
Technical Data
MC
After Completion MC M
of Loading
MC
(Delta Connection) MC
430V~470V
FB-01A1,02A1,05A1
0.2Watt and above
FB-1B
0.4Watt and above
FB-2B, 3B, 5B, 8B
0.6Watt and above
Brake input power
AC380V~460V
Rated voltage of varistor
AC510V
Varistor voltage
Rated
capacity of
varistor
Reverse
L1 L2 L3 (400V Class 3
Quick braking circuit
(400V Class
L1 L2 L3 3 Source) For Starting
MC MC
M M
ONON
(Star Connection) MC OFF
Forward
Forward
Source)
Y
Standard braking circuit
L1 L2 L3 (400V Class 3
400V Class 3 Source with
Starting Method)
400V Class FB Brake (
Reverse
400V Class 3 Source with
400V Class FB Brake (Direct Starting Method)
820V
FB-01A1,02A1,05A1
0.4Watt and above
FB-1B
0.6Watt and above
FB-2B, 3B, 5B, 8B
1.5Watt and above
181
Construction of terminal plate for brake motors (optional)
frame size 01#,03#,05# and 07#
(Motor frame F-50S, F-50M, F-50L, FS-50S, FS-50M, FS-50L)
Single-phase motor 15~40W 100V Class
Standard braking circuit
SW
MC
MC
C
Brake
S
2V
R
1U
B
B
Yellow
3W
Black
White
Motor
Blue
Yellow
Grey
Grey
Motor
Brake
3-phase motor 15~60W 200V Class
Standard braking circuit
3W
Black
White
Red
1U
Connection bar
Connection bar
4 2 1
Rectifier
Quick braking circuit
SW
Quick braking circuit
MC
MC
C
S
2V
R
1U
Yellow
3W
Black
White
Motor
Brake
Yellow
Grey
Grey
Motor
Blue
S
R
B
B
4 2 1
Rectifier
Brake
T
2V
Black
White
Red
2V
R
1U
B
B
B
B
4 2 1
Rectifier
T
S
3W
4 2 1
Rectifier
VR
VR
Connection of terminal plate for brake motors (optional)
for frame size 15# and 17#
(Motor frame F-56S, F-56M, F-56L, FS-56S, FS-56M, FS-56L)
2 3
V W
1
U
Red
B
Standard braking (at shipment)
Release
connection
conductor
White
Red
Release connection cnductor
Change connections of the
motor side
400V Class
Quick braking
Black
Yellow
White
Red
Yellow
2 3
V W
Black
Change connections of
the motor side
Black
1
U
Black
Yellow
White
Red
Yellow
White
0.1kW~0.4kW
White
B
3
W
Black
Red
B
1
U
Red
B
Yellow
3-phase
Note 1: Refer to page 163–173 for the connections shown above.
Note 2: Connect brake to primary power supply of inverter when the motor is driven by an inverter.
Note 3: Symbols and colors of lead wire are different when a motor is driven in the reversed
direction (standard: clock-wise rotation viewed from the fan cover.)
182
Red
B
Brown
Yellow
Black
Yellow
White
B
2 3
V W
Red
B
Black
White
White
Yellow
Black
B
Yellow
Quick braking
2 3
V W
Brown
200V Class
Black
B
White
Yellow
Black
Quick braking
Same as shipment
1
U
Standard braking (at shipment)
200V Class
B
40W~90W
Red
3
W
Single-phase
White
2
V
B
B
Yellow
Black
2
V
Red
Black
Yellow
White
Red
Yellow
White
1
U
Blue
B
Yellow
Black
40W~90W
1
U
1
U
Red
White
Yellow
Black
3-phase
Standard braking (at shipment)
B
Blue
White
2 3
V W
2 3
V W
Black
1
U
White
Yellow
Black
100V Class
Quick braking
B
40W~90W
B
Single-phase
Standard braking (at shipment)
White
Release connection cnductor
Change connections of the
motor side
Dimensions of separate rectifier
(15W~60W for frame size #01, 03, 05 and 07)
84
20
2.5
1
2
4
70
4
10
5
16
5
6 4 4 6
34
29
25.5
9.5
5
1
1.5
Technical Data
65
183
Protection of motor
No.1 Symbol form of protection of humans and solid foreign substances
s
Classified according to combination.
No.2 Symbol form of protection against water permeation
Table 16 Protection Method of Motors
No.2 Symbol
No.1 Symbol
No.2 Form
No.1 Form
0
2
3
Non-protected type
Drip-proof type
Spray-proof type
4
5
✕
0 (Non-protected type)
IP00
1 (Semi-protected type)
IP10
IP12S
2 (Protected type)
IP20
IP22S
7
✕
✕
✕
✕
✕
✕
✕
✕
IP24
✕
4 (Totally enclosed type)
✕
IP44
IP45
5 (Dust-proof type)
✕
IP54
IP55
6 (Complete dust-proof type)
✕
IP23S
6
Splash-proof type Water-jet-proof type Sea-wave-proof type Immersion-proof type
8
Submersible type
IP56
IP65
Note 1: ✕ mark denotes difficulty in forming the combination.
Note 2:
Outlined columns denotes the manufacturing range of Sumitomo.
Note 3: Contact us for motors of JP45 and JP55.
Table 17 Class of No.1 Symbol
Type
Symbol
Description
Non-protected
0
Constructed without special protection against human contact and penetration of solid foreign substances.
Semi-protected
1
Constructed to prevent inadvertent contact with rotating and conductive parts inside the machine, by hand or other critical
parts of human body. Constructed to prevent penetration of solid foreign substances over 50 mm in diameter.
Protected
2
Constructed to prevent contact with rotating and conductive parts inside the machine, by hand or other critical parts of the
human body. Constructed to prevent penetration by solid substances over 12mm in diameter.
Totally enclosed
4
Constructed to prevent contact with the rotating and conductive parts inside the machine, by tools, electric wires, etc., with minimum width and thickness over 1mm.
Constructed to prevent penetration of solid foreign substances over 1mm diameter. However, water drainage outlet and exhaust outlet may be of Symbol 2 construction.
Dust-proof type
5
Constructed to prevent contact with rotating and conductive parts inside the machine by and form of object. Constructed for
maximum protection against dust particles penetration, but will not interfere with normal operation, despite of such penetration.
Table 18 Class of No.2 Symbol
Type
Symbol
Description
Non-protected
0
Constructed without special protection against water permeation.
Drip-proof
2
Constructed to prevent harmful effect from dripping water falling from within 15° direction from vertical.
Spray-proof
3
Constructed to prevent harmful effect from dripping water falling from within 60° direction from vertical.
Splash-proof
4
Constructed to prevent harmful effect from dripping water falling from any direction.
Water-jet-proof
5
Constructed to prevent harmful effect from spray from any direction.
Sea-wave-proof
6
Constructed to prevent harmful effect from strong spray from any direction.
Immersion-proof
7
Constructed for submersion into water of prescribed depth and time, but not having any harmful effect in spite of water permeation.
Submersible
8
Constructed to assure normal operations under water.
Example:
IP – 5 4
S································ Test of form of protection against water permeation, conducted
SM
Form of protection against water permeation:
Splash-proof type
Form of protection against bodily injury and solid
foreign substances penetration: Dust-proof type
JEC Standards abbreviation (IP in case of IEC
Standards)
Cooling
184
Enclosure Construction
IEC Standards
Totally enclosed, non-ventilated (TENV)
IC410
Totally enclosed, fan-cooled (TEFC)
IC411
when motor is stopped.
M································ Test of form of protection against water permeation, conducted
while motor is operating.
When no S or M stipulated··· Test conducted when motor stopped and when operating
International Standards and corresponding Sumitomo standards for a motor
UL Standards (Underwriters Laboratories)
UL Standards are established for safety by a commercial testing institute in the US to prevent harmful effect to human life, fire
and disaster based on a series of scientific study, research and experiment. It is not regulated to comply with the standards by
Federal Government, but it is regulated by some states or cities. Approved products by UL standards are highly appreciated in
the US to represent your reliability.
Motor
Non-explosion proof singlephase induction motor ✻1
Non-explosion proof
3-phase induction motor
3-phase induction motor
with brake ✻1
1/50~8HP✕4P
1/50~8HP✕4P
Power
1/50~1HP✕4P
Voltage
115V, 230V ✻4
208V, 230V, 460V, 575V ✻4
Frequency
60Hz ✻4
60Hz
Insulation
Class A
2
1
✻3 Class A (Class B, Class F)
3
Class F
Indoor type ✻2
Ambient conditions
✻1. Single-phase motor or motor w/brake is manufactured in the range of 1/50 through 1/9 HP.
✻2. Outdoor type is available. Please consult us.
✻3. F-class insulation type is available. Please consult us.
✻4. For other voltages or frequencies, please consult us.
3-Phase indoor terminal box
UL mark
Differences from Sumitomo standard models
· Terminal symbol: 1,2,3
· Name plate with UL mark and measurement in HP
· Opposite rotating direction
· Copper terminal box
· UL standard motor coil and brake coil
HP
P
TYPE
VOLTS
Hz
AMP
RPM
CODE
SER. NO.
Remarks
· Manufacturing and repair work may be conducted only at authorized factories.
· Motor for inverter is excluded from UL approval. Sumitomo supplies UL compliant
AF motor. (UL mark is not fixed on a nameplate of UL compliant products.)
FRAME
INS. CLASS
TIME RATING
SERVICE FACTOR
MAX AMB
SUMITOMO
˚C
MACHINERY CORP. OF AMERICA
CHESAPEAKE, VIRGINIA
UL nameplate
CSA Standards (Canadian Standard Association)
National standards established by a semi-governmental organization in Canada. Most states in Canada require
electronic products to be approved by CSA. CSA is considered equivalent in some states in the US.
Motor
3-phase induction motor
3-phase induction motor
with brake
High efficiency 3-phase
induction motor ✻1
Power
1/8~1HP✕4P
1/8~1HP✕4P
1.5~5HP✕4P
208V, 230V, 460V, 575V
230V, 460V, 575V
Frequency
60Hz
Insulation
Class B (and Class F)
Ambient conditions
✻1
1.5~5HP✕4P
Indoor type
✻2
Technical Data
Voltage
High efficiency 3-phase
induction motor with brake
✻1: Contact us for manufacture of a single-phase motor or a high-efficiency motor with brake. ✻2: Outdoor type not supplied
✻3: Some 1/50 through 1/9HP¥4P are CUL approved products which are permitted for us in Canada.
Differences from Sumitomo standard models
· Terminal symbol: 1,2,3 (with Brake type, T1, T2, T3)
· The frame size of a high-efficiency motor is specil.
· Name plate with CSA mark and measurement in HP
· Opposite rotating direction
· Copper terminal box
· CSA standard motor coil
2
1
3-Phase indoor terminal box
Remarks
· If exporting to Canada, it should be CSA approved motor and if above 1HP, High efficiency
motor is needed.
· Manufacturing and repair work may be conducted only at authorized factories.
· Motor for inverter is excluded from CSA approval. Sumitomo supplies CSA compliant AF
motor. (CSA mark is not fixed on a nameplate of CSA compliant products.)
NRCan established the energy efficiency act (EEACT) in 1992 and the energy efficiency regulations
(EER) in 1995, and additional regulations were applied to gearmotors imported on November 27, 1999
or later. Import of gearmotors that do not meet the efficiency standards has been banned. This rule
applies to the following motors : 1-200HP, IEC frame 90 and larger, 600V or less, constant speed.
3
HP
VOLTS
Hz
M.AMP
RPM
B.AMP
B.TORQUE
MANUF. No.
P
FT-LB
TYPE
FRAME
M / B INS. CLASS ／
TIME RATING
SERVICE FACTOR
MAX.AMB
˚C
ENCLOSURE
TE
SM CYCLO OF CANADA, LTD
TORONTO, MONTREAL, VANCOUVER
CSA nameplate
185
International Standards and corresponding Sumitomo standards for a motor
NEMA Standards (National Electrical Manufacturers Association)
Established by a manufacturers' association to provide standards of most
electrical products for both manufacturers and consumers.
2
1
3
Differences from Sumitomo standard models
· Terminal symbol: 1,2,3
· Name plate marked with NEMA DESIGN and measurement in HP
· Opposite rotating direction
· Copper terminal box
3-Phase indoor terminal box
NEMA standard motor coil
HP
VOLTS
Hz
M. AMP
RPM
CODE
B. AMP
SERIAL NO.
Remarks
· No approval is required to state NEMA compliance
· NEMA is also applicable for inverter motor, but limited to terminal symbols,
measurement in HP, rotating direction and terminal box.
P TYPE
FRAME
M B INS. CLASS
TIME RATING
SERVICE FACTOR
MAX. AMB.
B. TORQUE
NEMA DESIGN
˚C
FT LB
J A PA N
NEMA nameplate
Other standards
Application of International
Standards (Example)
Country/Standards
● : Sumitomo standards
■ : Manufactured to special specification on customer's request
JIS
Japan · JEM
JEC
International·IEC
UK · BS
Germany· VDE
DIN
■ : 4kwmax.
● : 5.5kwmin.
■ : 4kwmax.
● : 5.5kwmin.
Standard output
●
●
Applicable output frame
size
●
—
■
■
Motor mounting dimension of
corresponding frame size
●
●
●
●
Shaft end dimension
●
●
■
■
Dimension tolerance of shaft
end key and key groove
●
●
■
■
Insulation class
●
●
●
—
Lead wire code
●
●
●
●
Standard direction of
rotation
●
■
■
■
Description on nameplate
●
■
■
■
●
●
■
■
Standard voltage
200V · 220V
400V · 440V
■
415V
220V
380V
Standard frequency
50Hz · 60Hz
50Hz · 60Hz
50Hz
50Hz
Characteristic testing
method
IEC–nternational Electrotechnical Commission.
BS–British Standards.
(Note): Dimensions of flanges and shafts
are suitable for Sumitomo products
only. For other dimensions, consult
factory.
Major Japanese Standards
(1) General rotating electrical machines
JIS C 4004 (1992) : General rules for rotating electrical machines
JEC-200
(1993) : Rotating machinery in general
JEM 1188 (1969) : Rated output values of electric motors
(2) General 3-phase induction motors
JIS C 4210 (1983) : Low-voltage 3-phase squirrel cage induction motors
for general purpose
JIS C4212 (2000) : High efficiency low-voltage 3-phase squirrel cage
induction motors.
JEC-37
(1979) : Induction machines
(3) Methods of testing and calculating characteristics
JEC-37
(1979) : Induction machines
JIS C 4207 (1995) :Calculating method of 3-phase induction motors
characteristics
(4) Dimensions
JEM 1400 (1991) : Dimension of low-voltage 3-phase squirrel cage
induction motors for general purpose
JEM 1401 (1991) : Dimensions of flange-mounted low-voltage 3-phase
squirrel cage induction motors for general purposes
(5) Explosion-proof construction
JIS C 0903 (1983) : Electrical apparatus for explosive atmospheres in
general industries
186
JIS C 0904 (1983) : Test methods on electrical apparatus for explosive
gas atmospheres in general industries
JIS C 0905 (1983) : Supplementary requirements for construction of
electrical apparatus for explosive atmosphere in
general industries
Recommended practices for explosion-protected electrical installations in
general industries (1979)
Rules for authorization of explosion-proof construction of electrical
machine tools (1981)
(6) Others
JIS C 4003 (1977) : Classification of materials for insulation of electrical
machinery and apparatus
JEC-147
(1960) : Classification of materials for insulation of electrical
machinery and apparatus
JEM 1313 (1983) : Noise levels for low-voltage 3-phase squirrel-cage
induction motors for general purpose
Remarks: JEC Japanese Electrotechnical Committee Standards
JIS Japanese Industrial Standard
JEM Japan Electrical Manufacturers' Association
International Standards and Compliance of Sumitomo Products
CCC
CCC Standards
Standards (China Compulsory Certification)
China had implemented the China Compulsory Certification (CCC) system since May 1, 2002 as becoming the full
member of World Trade Organization (WTO). They have moved on to compulsory licensing on August 1, 2003.
Motor capacity 1.1kW and below are subject to this certification, and requires CCC Mark for sales in China. Below table
is our motor with CCC.
Motor
Single Phase Motor
Three Phase Motor
Capacity
15~90W
0.1~0.75kW
Voltage
220V
Frequency
50Hz
Thermal class Class E
Class B
Usage
Indoor (IP44), Outdoor (IP55)
40~90W
AF Motor
AF Motor (Foot Mount)
0.1~1.1kW
0.1~0.75kW
220 or 380V
50Hz
Class F
Indoor (IP44), Outdoor (IP55)
Class E
0.4~0.75kW
AF motor: 3 Phase Motor for inverter
Difference with standard items
- CCC Mark as in the right is applied on the nameplate.
- Aluminum terminal box is the standard for three phase motor (except indoor
specification for 40~90W).
- Terminal block type (6 terminals, European system) is the standard for three
phase motor (for 0.1kW or more).
- Rotational direction is the opposite from Japanese domestic specification
(in CCW direction looking from the anti-load side).
- CCC correspondence motor coil is used.
China Compulsory Certificate
Remarks
Remarks
· CCC Mark is necessary when exporting small size motor (or gearmotor) units
of 1.1kW or below to China.
· Subject service products and spare parts without certification may be permitted
for import to China by applying for exemption.
Consult us for any clarification.
GOST-R Standard
(Russian Gosstandard)
GOST-R Standard is a national certification system determined by State Committee of Russian Federation for
Standardization and Metrology.
Any product distributed in the Russian Federation is requires certification. Especially products subject to compulsory
certification are not allowed to export to Russian Federation without this certification.
Sumitomo offers motors conforming to GOST-R specification for export to Russia, because motors are subject to
compulsory certification.
Our Certified Motor Specification (Range other than the below is the same as CE Marking of Europe)
Capacity x 4P
General motor
Without brake
Inverter motor (AF motor)
With brake Without brake With brake
Without brake With brake
Without brake
With brake
0.1~3.7kW
5.5kW
0.1~3.7kW
5.5kW
0.1~2.2kW
3.7kW
0.1~2.2kW
3.7kW
Motor voltage 220/380V
380V
220/380V
380V
220/380V
380V
220/380V
380V
220V
380V
-
-
220V
380V
Brake voltage
-
-
Frequency
50Hz
Thermal class
F
Rating
Construction
Starting
60Hz
F
S1 (continuous)
Indoor (IP44), Outdoor (IP55)
Dual voltage inline
S1 (continuous)
Technical Data
Motor
Indoor (IP44), Outdoor (IP55)
Dual voltage inline
-
AF motor: 3 Phase Motor for inverter
Difference Compared to Standard Japanese Product
- Nameplate is marked with GOST-R Mark (as shown in the right).
- Standard terminal box is made of Aluminum
- The motor has terminal block (European type with 6 terminals).
- Rotation direction is counterclockwise view from fan cover side
(opposite from Japanese specification).
- Motor coil is certified for GOST-R.
GOST-R Mark
Cautions
· Uncertified products can not pass through customs when exported to Russia.
(No specific certification is necessary when the unit is exported to Russia as a
part of the machine.)
-A verified copy of the certification is necessary when exporting the individual
unit for each case (each ship).
Let us know when ordering the units which are not included in an apparatus or
not built into the exported aparatus.
187
EC directives and CE marking
The CE mark is to be affixed to products that conform to EC directives, in order to certify the quality and safety of products and
ensure free distribution of products across borders within the region of the EU (European Union).
EC directives applicable to machine products and implementation period
The following three directives apply to ordinary machine products.
EC directives
Details
Machinery directive
Machinery
Directive
Low Voltage Directive
Low Voiage
Directive
EMC Directives
Electromagnetic
Compatibility
Directive
Electromagnetic
Compatibility
Objects
Aggregates of parts, which are movable
(Industrial machines, primarily)
Products driven by power of 50-1,000 VAC or
75-15,000 VDC
All types of products that may cause jamming
(electromagnetic radiation) or have their
functions impeded by nearby radio waves
Details of directive
Essential matters related to safety of machines
are stipulated. Machines that are electrically
dangerous shall fulfill the requirements for low
voltage.
Products not conforming to standards cannot
be put on the market.
EMI : Not to cause external electromagnetic
interference
EMS : To withstand external electromagnetic
interference
Transition period and time limit for enforcement of CE marking for major directives
EC Directiv
Year
1990
1991
1992
Machinery Directive
89/392/EEC Original
91/368/EEC Revision I
93/44/EEC
Revision II
EMC Directives
89/336/EEC Original
92/31/EEC
Revision I
Low Voltage Directive
73/23/EEC
Original
93/68/EEC
Revision I
1993
1994
1/1
1995
1996
1997
1998
1999
2000
2001
1/1
Transition
Enforcement
1/1
1/1
Transition
Enforcement
1/1
1/1
Transition
Enforcement
Measures to take for EC directives and CE marking related to gear motors
Among EC directives, the machinery directive (issued in January 1995)
concerning induction motors and low voltage directive (issued in January
1997) are applicable.
The EMC directive (issued in January 1996) does not apply to induction
motors.
188
CE marking logo shown
on nameplates
2002
2003
EC directives and CE marking
Standard Specifications of CE Marking Motors
Input power
Insulation
Rated time
Characteristics
Protection
Terminal box
Shaft rotating direction
Insulation
External dimensions
TÜV test report
Declaration of Conformity
: 15W~90W 200V 50Hz Direct start-up
0.1kW~4kW 230/400V 50Hz Dual voltage direct starting
Y
5.5kW or more 400V 50Hz –
Start
: 15W~0.4kW Class E
0.75kW or more Class B
: Continuous
: IEC34-1
: P54 (without brake), IP44 (with brake) 15W~90W : Aluminum (M20 bolts(P1.5)✕1pcs)
: (Material)
5.5kw or less : Aluminum (PG16 bolts✕2pcs or M25 bolts (P1.5)✕2pcs)
7.5kw or more : cast iron (PG21 bolts✕2pcs or M32 bolts (P1.5)✕2pcs)
(specification) Terminal plate (six terminals European style)
with grounding terminal
Conduit tube in European size (*PG thread or M thread) *different from
Japanese standard of conduit tube PF thread.
Models of 15W~90W contain M thread and cable ground (applicable lead
diameter P6.0~12)
: Rotating direction is reverse to Japanese standard direction.
: Distances between insulated surfaces and spaces in accordance with IEC standards.
: Same as standard except for the terminal box Length night vary in some cases for models
90W or less.
: Acquired for a representative model 0.75kW✕4p, 230V/400V (Oct 1996)
CE marking motors are manufactured in accordance with the model.
: Declaration of Conformity is available when necessary for CE marking
97
81
50
5.5kw or less
59
49
56
terminal box example
Terminal plate
(six terminals
in European
style)
16
16
30.5
2-PG16
(2-M25 P1.5)
Manufacturing range of CE Marking motors
3-phase induction motor
004
Input power symbol 0015 0025
(0.015) (0.025)
(0.04)
kW✕4P
F50S F50M F50L or F56S
Frame
Input power symbol 1H
kW✕4P
1.1
Frame
F90S
006
(0.06)
F50L or F56M
230/400V dual voltage
2
3
4
5
6
1.5
2.2
3
(3.7)
4
F90L F100L F112S
F112M
230/400V dual voltage
009
01
012
018
(0.09) (0.1)
0.12
0.18
F56L
F63S
02
(0.2)
F63M
03
0.25
04
05
0.37
(0.4)
F71M
08
0.55
F80S
1
0.75
F80M
Technical Data
Connection
bar
400V
8
5.5
F132S
· Motors of kWs without brackets ( ) in the above table are standard in Europe while motors of kWs with brackets ( ) are
used only in Japan and other countries.
· European standard kW motors are recommended. Motors of kWs with brackets ( ) are also available.
3-phase
200V/50Hz, 200V/60Hz, 220V/60Hz
3-phase
400V/50Hz, 400V/60Hz, 440V/60Hz
3-phase
380V/50Hz, 3P 415V/50Hz
Contact us when motors of kW and voltage not shown in the above table are required
· Consult us when M bolt (Metric bolt) is needed for conduit tube.
189
Precautions for Inverter Driving
1. Constant torque operation
Constant torque operation needs a special motor for the inverter. Contact us especially when operation is in the frequency range
less than 6 Hz.
The sensorless operation mode of our inverter HF-320 permits constant torque operation of general-purpose motors at 3.7 kW or
less.
2. Operation in frequency range exceeding the base frequency (60 Hz)
Rated output operation will be carried out in the frequency range exceeding the base frequency. Therefore, the torque will
decrease as the speed increases. Select an appropriate motor capacity according to the machine load characteristics. (See Fig.
25.)
The frequency exceeding 60 Hz is regarded as the base frequency. The output torque is lower than that at 60 Hz, which is the
standard base frequency, also when V/f is set for constant torque operation.
When such adjustment is made, insufficient torque may result at low frequency or during start-up.
Do not change the base frequency figure for cases other than reduction load characteristics.
3. V/f mode operation of general-purpose inverter
In the case of multiple operation of motors or V/f operation with an inverter that has no sensorless function, it is necessary to adjust
the boost value in compensation for the start-up torque and slow-speed torque. Standard values are usually set before shipment
from manufacturer's factory but overcurrent may result depending on the load condition and acceleration/deceleration. In such a
case, change values appropriately as follows :
a. In the case of a small capacity motor and a small load, a large boost setting may
cause overexcitation of a motor, leading to overcurrent. In that case, lower the
boost to return to a normal value.
b. In cases where a load is large and overcurrent during start-up and slow-speed
operation easily causes tripping, increase the boost to lower the current value. If
no improvement is observed after boost adjustment, it is necessary to examine
the motor capacity.
Output frequency (Hz)
Base frequency
Boost
4. Operation by sensorless vector inverter
Base voltage
Output voltage (V)
Some high-performance inverters of a newest type are equipped with a
sensorless vector operation function. This function is basically valid only when a motor and an inverter are operated in one-to-one
correspondence. The function does not apply to multiple operation or pole-change operation. Products to which the auto-tuning
method is applied do not need adjustment as in the case of V/f operation due to automatic control of the motor characteristics.
Vector operation is carried out on the basis of the motor data read by the inverter, and operation is controlled instantaneously in
accordance with the load condition to continue optimal operation.
When the wiring distance between the motor and inverter becomes long (20 m or more), compensation may be necessary
according to the drop in the line impedance. Select sufficiently thick cables when the wiring distance is long.
5.Output torque characteristics of motor
● Total output/torque characteristics curve when motor for
inverter and SUMITOMO inverter are operated in combination
● Continuous operation characteristics when a generalpurpose motor is driven by an inverter
When a general-purpose motor is
driven by an inverter, the reduction
torque operation characteristics
shown below will appear.
(%) (%)
Output Torque
80
Torque (%)
100
95∼100
80∼90
Torque curve
100
Output curve
Motor for
inverter
50
50
220V (440V)
200V (400V)
General-purpose motor
40∼60
35∼45
20
0 6
60
120
6
Output frequency (Hz)
Note: Constant torque operation is possible from 1 Hz when an
axial fan type is used.
Fig. 25
20∼30
60
120
Output frequency (Hz)
6. Motor temperature rise
When a general-purpose motor is combined with an inverter for variable-speed operation, the motor temperature rise may be
slightly greater than if the motor is operated by a commercial power supply.
Possible causes are shown below :
Influence of output waveform ・・・・Unlike a commercial power supply, the output waveform of an inverter is not a complete sine
wave but includes harmonics; therefore, motor damage will increase, raising the temperature
slightly higher.
Decrease in motor cooling effect during slow-speed
operation ・・・・・・・・・・・・・・・A motor is cooled by its own fan. Therefore, when the motor speed is decreased by an
inverter, the quantity of cooling air decreases, reducing the cooling effect.
When a motor is to be operated at frequencies lower than the frequency of a commercial power supply, reduce the load torque to
hold down the temperature rise or use a special motor designed for inverter operation.
190
Constant Torque Operation of General-Purpose Motors
Operation with the following characteristics is possible when our inverter HF-320 series is used for sensorless control in combination
with our general-purpose motors (3.7 kW or less).
A combination with a motor of standard frame size can be used for constant torque operation where an inverter motor with a reducer of
a larger frame size has conventionally been used.
Notes : 1. Contact us for 400V class model because insulation selection is necessary for inverter operation.
2. When a motor with brakes is to be operated for a long time at slow speed, the cooling effect of the fan will decrease and the
brake temperature will rise substantially.
Contact us for details.
3 Contact us for details when a general-purpose motor is to be operated under V/F control. (Contact us also when SF-320
series is to be used.)
kW
Motor frame
size
0.1
F63S
0.2
F63M
0.4
F71M
0.75
F80M
1.5
F90L
2.2
F100L
3.7
F112M
Insulation
Frequency
range
Series of
inverter
6~120Hz
Class F
HF-320_
(Base frequency
60HZ)
Series
HF-320_ Output Torque Characteristics during Operation in
Sensorless Mode
Torque (%)
Torque (%)
150
Continuous operation
torque
100
150
80
50
40
50
40
6
20
40
60
120
Continuous operation
torque
100
80
0
Short time maximum torque
200
0
6
20
40
60
Frequency (Hz)
0.2~0.4kW
120
Frequency (Hz)
0.75~3.7kW
● The combination-output torque presupposes that the rating is 100% when the frequency of motor power
is 60 Hz. Use an inverter motor when constant torque is required at the power exceeding 5.5 kW.
Technical Data
Short time maximum torque
200
191
Painting specifications
1. Painting Quality and color
0.1kW~5.5kW
Indoor, Outdoor type
3-phase, single-phase
and for inverters
Cast iron :
Near White
blast cleaning
Steel plate :
Power tool
cleaning
Cast iron :
Near White
blast cleaning
Steel plate :
Power tool
cleaning
Brand
Etching
Primer
Shinto wash #20
0
1
Under
coating (5~10)
Acrylic resin
0
Acrylic resin
1
Finish
coating (15~25) baking top coat
Saglan 33
1
Under
Modified alkyd UNIGROUND
PTC PRIMER
coating (20~40)
resin
Acrylic
Acrylic
Finish
1
0
SUPIKA #3000
coating (15~30) modified phtalic
modified phtalic
—
✕
0
✕
Acid
resistance
Alkali
resistance
Quality
Oil-proof
Layers
(μm)
—
Standard
Standard
Type
Applied paint
Submersible
Paint of
Classification finish coat
Painting specifications
Heat
resistance(˚C)
15W~90W
Indoor type
Water-proof type
3-phase, single-phase
Treatment
Weather
resistance
Kind of painting
Model
Additional
leadtime(days)
1-1. Standard Painting Quality
Application
100
Standard
under coat
100
Standard
finish coat
100
Standard
under coat
100
Standard
finish coat
: Appropriate
: Caution in selection
✕ : Inapproprlate
1-2. Standard Painting Color
Model
15W~90W
Indoor type
3-phase, single-phase
0.1kW~5.5kW
Indoor, Outdoor type
3-phase, single-phase
and for inverters
192
Painting Color
Gear case and motor : Warm silver
Terminal box, Safety cover, Brake cover : Warm beige
Equivalent to Muncell 6.5PB 3.6/8.2
Painting specifications
Modified
epoxy
3
Long oil phtalic
(synthetic resin
type)
7
Chloride
rubber
1
Under
coating (30~60)
Modified alkyd resin
UNIGROUND PTC PRIMER
1
Finish
coating (15~30)
Acrylic modified
alkyd resin
SUPIKA #3000
1
Under
coating (20~40)
Vinyl modified
epoxy paint
NEO-GOSE #500
Red lead primer
1
Finish
coating (30~60)
Acrylic modified
alkyd resin
Acron #300
2
Under
coating (40~70)
Lead rust
preventive paint
SSD MARINE
PRIMER (rust)
2
Finish
coating (30~60)
Synthetics
resin paint
PENFORTE #600
2
Under
coating (40~70)
Lead rust
preventive paint
SD MARINE PRIMER
(rust)
Phenol M.I.O. pain
SHINTOH M10
1
10 Second
coating (20~40)
Heat-proof
silver
Epoxy
7
7
Lead rust preventive SD MARINE PRIMER
(rust)
paint
2
Finish
coating (30~60)
Phenol resin enamel
1
Under
coating (20~40)
Lead rust preventive SD MARINE PRIMER
(rust)
paint
1
Finish
coating (15~30)
10
Epoxy
10
Thick film
epoxy
12
✕ ✕
Ocean-going
vessel & boat,
100
✕
bridge, sea side,
outdoor humid
atmosphere, etc.
80
Ocean-going
vessel & boat,
bridge, sea side,
outdoor humid
atmosphere, etc.
✕
100
In-and-out door
of acid treating
plant and chemical
plant, etc.
NEW AKNON
SILVER TOP (heat
resisting)
✕ ✕ ✕ ✕ 120 Heating furnace
(120°C), etc.
Chemical contact
area, chemical
150
plant, anticorrosion plant,
etc.
NEO-GOSE #200
1
Under
Special permeability
coating (50~60) epoxy aluminum paint CARBOMASTIC #15 ✻
150
Nuclear power
plant, etc.
150
Nuclear power
plant, etc.
NEO-GOSE
#2300CW
Polyamide epoxy
1
Under
Special permeability
coating (50~60) epoxy aluminum paint CARBOMASTIC #15
3
Finish
coating (45~90)
Extra rustpreventive painting
(sand blast
undercoating)
Polyamide epoxy
Export
Moderate corrosive
atmosphere, sea
side,
outdoor humid
100
atmosphere,
chemical plant area,
etc.
1
Under
Special permeability
coating (50~60) epoxy aluminum paint CARBOMASTIC #15 ✻
3
Finish
coating (120~240)
Polyurethane 10
Aluminum paint
✕ 100
Application
RUBBER #100
2
Under
coating (40–70)
3
Finish
coating (30~90)
Extra rust-proof
painting
✕
2
Finish
coating (40~70) Chloride rubber paint
Phenol
Steel plate :
Power tool
cleaning
Brand
Polyisocianate
urethane resin paint
NY POLIN K finish
coat
5
Thick film type modified
epoxy resin paint
(250~350)
NEO-GOSE #2300
NTHB
Notes : 1. Additional lead time for coating refers to the number of days required for special
coating compared to standard painting.
2. Coating may be substituted.
3. The coatings marked with ✻ may fade from the sun's ray.
4. Consult us when ambient temperature is above the heat resistance temperature.
(The above heat resistance temperature is only for the painting and not for gearmotor.
5. Consult us when ambient temperature varies widely in a short period.
Submersible
100 equipment, marine
structure, etc.
✕
: Appropriate
: Caution in selection
: Inappropriate
Technical Data
Special painting
(including rust-proof
and heat resisting
painting)
Cast iron :
one layer of
Near White Uniground PTC
blast
Primer as the first
cleaning
primer
2
Quality
Heat
resistance(˚C)
Acrylic
modified
phtalic
Layers
(μm)
Acid
resistance
Alkali
resistance
Standard export
painting
Type
Oil-proof
Paint of
finish coat
Applied paint
Submersible
Classification
Painting specifications
Weather
resistance
Kind of painting
Treatment
Additional
leadtime(days)
1-3.Painting Specifications except Standard
193
Painting specifications & Rust proof
2. Surface conditioning
Standards
Treatment
Surface condition after treatment
Methods
Class 1
Near white
blast
cleaning
Surface to be completely free of mill scales, rust, corrosive substances,
dirt and other foreign substances. However, solidly embedded residues
(mill scales, rust, slight smears or discoloration of oxide substances) may
be excepted, provided that a minimum of 95% of the surface area is
visually free of any residues and the remaining area is limited to smears,
stains and other minute loose particles.
Near White
Blast Cleaning
●Shot blast
Class 2
Power tool
cleaning
Except for solidly embedded mill scales, the surface shall be completely
free of loose mill scales, rust, corrosive substances, oil & grease, dirt and
other foreign matters. However, solidly embedded residue (mill scales,
rust, slight smears or stains of oxide substances) may be excepted. If
there is any porous corrosion in the surface, residual rust and coating
peelings may remain in such pores, but a minimum of two-thirds of the
surface shall be visually free of such residues, with the remaining area
being limited to minor smears, stains and other loose minute particles.
Commercial Blast Cleaning
Power Tool Cleaning
●Disk sander
Class 3
Hand tool
cleaning
Remove the loose scale, rust, coating peelings, oil & grease and other
foreign matters, with a wire brush, scrapper, etc. The surface shall have
a slight metallic luster.
SSPC
SIS
SP-10
Sa-2 1/2
SP-6
(SP-3)
Sa-2
(St-3)
SP-2
St-2
●Sand blast, etc.
●Wire wheel
●Grinder, etc.
Hand Tool Cleaning
●Wire brush
●Scrapper, etc.
Ref. SSPC (U.S.A. Steel Structural Painting Councils) and SIS (Sweeden, Svensk Standard, S.I.S 055900)
Rust Proof Standards
Rust proof treatment is applied to all completely assembled models, prior to shipment.
1. Standard specifications of rust proof
(1) External treatment
Rust-proof oil is applied prior to shipment. Check the condition every six months and reapply the oil if necessary.
(2) Internal treatment
Rust-proofing period
One year
Storage condition
To be stored inside the shop or warehouse, relatively free of humidity, dust, extreme variation of temperature,
corrosive gas and similar atmosphere.
2. Export specifications of rust-proof
Contact us for export rust-proof when special treatment is required or goods are exported.
194
Warranty
Warranty
Condition
Warranty
Exclusions
The warranty period for the Products shall be 18 months after the commencement of delivery or 18 months after the shipment of
the Products from the seller's works or 12 months from the Products coming into operation, whether comes first.
In the event that any problem or damage to the Product arises during the "Warranty Period" from defects in the Product
whenever the Product is properly installed and combined with the Buyer's equipment or machines, maintained as specified in
the maintenance manual, and properly operated under the conditions described in the catalog or as otherwise agree upon in
writing between the Seller and the Buyer or its customers; the Seller will provide, at its sole discretion, appropriate repair or
replacement of the Product, without charge, at a designted facility, except as stipulated in the "Warranty Exclusions" described
below.
However, if the Product is installed or integrated into the Buyer's equipment or machines, the Seller shall not reimburse the cost
of: removal or re-installation of the Product or other incidental costs related thereto, any lost opportunity, any profit loss or other
incidental or consequential losses or damages incurred by the Buyer or its customers.
Not withstanding the above warranty, the warranty as set forth herein shall not apply to any problem or damage to the Product
that is caused by :
1. installation, connection, combination or integration of the Product in or to the other equipment or machine that is rendered by
any person or entity other than the Seller ;
2. insufficient maintenance or improper operation by the Buyer or its customers, such that the Product is not maintained in
accordance with the maintenance manual provided or designated by the Seller ;
3. improper use or operation of the Product by the Buyer or its customers that is not informed to the Seller, including, without
limitation, the Buyer's or its customers' operation of the Product not in conformity with the specifications, or use of
lubricating oil in the Product that is not recommended by the Seller ;
4. any problem or damage to any equipment or machine to which the Product is installed, connected or combined, or on any
specifications particular to the Buyer or its customers ;
5. any changes, modifications, improvements or alterations to the Product or those functions that are rendered on the Product
by any person or entity other than the Seller ;
6. any parts in the Product that are supplied or designated by the Buyer or its customers ;
7. earthquake, fire, flood, sea-breeze, gas, thunder, acts of God or any other reasons beyond the control of the Seller ;
8. normal wear and tear, or deterioration of the Product's parts, such as bearings, oil-seals ;
9. any other troubles, problems or damage to the Product that are not attributable to the Seller.
Technical Data
Warranty
Period
195