Pg 1 - Standard shipment with power cord attached to fixture. Pg 2 - Sail Installation Pg 3 - General Maintenance features - access to internal components. Pg 4 - If mounting hardware is shipped ahead for installation before fixture arrives. 4" OCTAGONAL ELECTRICAL JUNCTION BOX (BY OTHERS) CEILIN G MA POWER CORD STRAIN RELIEF TERIAL JUNCTION BOX MOUNTING SCREWS MOUNTING CROSSBAR ASSEMBLY STAINLESS STEEL SUPPORT CABLE STAINLESS STEEL CABLE CANOPY SCREWS (SUPPLIED) CANOPY (STYLE MAY VARY) DMX CONTROL CABLE (ONLY FOR FIXTURES WITH RGB LAMPING BUT WITHOUT THE RMB OPTION) FIXTURE POWER CORD DMX CONTROL CABLE GRIPPER JAM NUT 1717 West Civic Drive Milwaukee, WI 53209 414-354-6600 Design Modification Rights Reserved © Visa Lighting 2015 TOP OF FIXTURE BODY INSTALLATION INSTRUCTIONS: CP2072 Fixture family name: Sequence Sail LED 8" Dia Body Description: FIELD INSTALLATION INSTRUCTIONS Cable Hung Fixtures Drawing : 762037XX Rev: B Page 1 of 4 Eng: AJM Date drawn: 7/20/2015 Drawing : 762037XX Rev: B Page 1 of 4 1) Fasten Mounting Cross-Bar Assembly to junction box with junction box screws. 2) Making sure Stainless Steel Cable and power cord are passing through their respective holes in the canopy, lift Fixture up and insert Stainless Steel Cable into Cable Gripper at top of Fixture Body. (See detail at right) 3) At the mounting Cross-Bar Assembly, insert Fixture Power Cord. 4) Make final adjustments to the fixture height and secure the Power Cord with strain relief and secure Stainless Steel Cable at Cable Gripper by tightening Jam Nut. 5) Make all wire connections per local and national codes. (see page 3 for typical wire color scheme) 6) Lift canopy in place and secure with screws provided. 7) If your installation requires the DMX control cable, it must be routed outside the junction box due to the low voltage class of the cable. ! Instructions - Standard shipment with cord attached to fixture. POWER CORD When using electrical equipment, basic safety precautions should always be followed, including the following: 1) Read all instructions carefully before installing and save for future use. Make sure all connections are in accordance with the National Electrical Code and local regulations. 2) To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture. Service should be performed by qualified personnel. 3) These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. SPECIAL NOTE: INSTRUCTION PACKET HAS MULTIPLE PAGES, READ CAREFULLY AS INSTRUCTIONS MAY DIFFER DEPENDING ON OPTIONS ORDERED A 1.8" 9.5" DETAIL A FIGURE 1 SAIL 1/4-20 STUDS TOGGLE BOLT 512 CADDY CLIP SUSPENDED DRYWALL TRIM WASHER GRIPLOCK 1/16 STAINLESS STEEL CABLE FIGURE 3 FIGURE 4 ! FIGURE 2 3. 4. The sail requires two mounting locations next to the junction box as dimensioned in figure 1. Suspended ceilings: Install 512 HD Caddy Clip (by others), install mounting kit as shown in figure 2. Drywall ceilings: install mounting kit as shown in figure 3. (keep trimwasher to the ceiling side) With the 1/16" dia cables installed in the sail (figure 4), lift the sail up to the Griplocks and insert cable. Center the position of the sail on the fixture and trim off the excess cable near the ceiling. 1717 West Civic Drive Milwaukee, WI 53209 414-354-6600 Design Modification Rights Reserved © Visa Lighting 2015 INSTALLATION INSTRUCTIONS: CP2072 Fixture family name: Sequence Sail LED 8" Dia Body Description: FIELD INSTALLATION INSTRUCTIONS Cable Hung Fixtures Drawing : 762037XX Rev: B Page 2 of 4 Eng: AJM Date drawn: 7/20/2015 Drawing : 762037XX Rev: B Page 2 of 4 INSTRUCTIONS 1. 2. When using electrical equipment, basic safety precautions should always be followed, including the following: 1) Read all instructions carefully before installing and save for future use. Make sure all connections are in accordance with the National Electrical Code and local regulations. 2) To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture. Service should be performed by qualified personnel. 3) These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. SAIL INSTALLATION ACRYLIC TUBE TUBE HOOK DMX512 INTERFACE CHANNEL SETTING DIALS (RGB ONLY) THUMB SCREWS (2) TUBE HOOK / DMX PORT To support the Acrylic Tube for maintenance lift the Acrylic Tube to access the Tube Hook. Swing the Tube Hook up and rest the Acrylic Tube on the Hook. DOOR OF WIRE BODY HEX NUTS (4) DOWNLIGHT REFLECTOR INSTRUCTIONS TO ACCESS INTERNAL COMPONENTS 1) See Tube Hook detail for supporting Acrylic Tube 2) Remove Thumb Screws to remove Downlight Bezel 3) Twist Downlight Reflector counter clockwise to remove it 4) Remove (4) Hex Nuts to remove Tube Support 5) Remove (2) Phillips Screws attaching the door of wire body and pivot it open INSTALLATION INSTRUCTIONS: CP2072 Fixture family name: Sequence Sail LED 8" Dia Body Description: FIELD INSTALLATION INSTRUCTIONS Cable Hung Fixtures Drawing : 762037XX Rev: B Page 3 of 4 Eng: AJM Date drawn: 7/20/2015 Drawing : 762037XX Rev: B Page 3 of 4 1717 West Civic Drive Milwaukee, WI 53209 414-354-6600 Design Modification Rights Reserved © Visa Lighting 2015 DOWNLIGHT BEZEL (FLAT DISK IF NO DOWNLIGHT) ! PHILLIPS SCREWS (2) TUBE SUPPORT When using electrical equipment, basic safety precautions should always be followed, including the following: 1) Read all instructions carefully before installing and save for future use. Make sure all connections are in accordance with the National Electrical Code and local regulations. 2) To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture. Service should be performed by qualified personnel. 3) These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. MAINTENANCE FEATURES INSTRUCTIONS POWER CORD DMX CABLE (RGB ONLY) GRIPPER JAM NUT 1) Preparation: Determine the height the Fixture will hang by holding Fixture along side Stainless Steel Cable. Stainless Steel Cable may be inserted into Cable Gripper up to 12", cut excess if needed. The cut end must not have stray-strands, tin the cut end. 2) Follow instructions on page 2 to gain access to the interior components. 3) Instert the Stainless Steel Cable so Fixture hangs at the intended height. Secure with Gripper Jam Nut. 4) Slide Power Cord thru Cord Grip. 5) Leaving enough cord for splices, trim Power Cord if needed. 6) Strip Power Cord and make appropriate splice connections. 7) If your installation requires the DMX Control Cable, it must be routed outside the junction box due to the voltage class of the cable. 8) Test, then reassemble Fixture. ELECTRICAL CONNECTION PANEL CORD GRIP Power Cord Connections ! GREEN: GROUND Lead WHITE: COMMON Line Voltage Lead BLACK: HOT Line Voltage Lead for White LED Body Light BLACK/WHITE: HOT Line Voltage Lead for Optional Downlight BROWN: HOT Line Voltage Lead for Optional RGB LED Body Light VIOLET: 0-10V DIM for Body Light GREY: 0-10V DIM for Body Light VIOLET/WHITE: 0-10V DIM for Downlight GREY/WHITE: 0-10V DIM for Downlight When using electrical equipment, basic safety precautions should always be followed, including the following: 1) Read all instructions carefully before installing and save for future use. Make sure all connections are in accordance with the National Electrical Code and local regulations. 2) To avoid possible electric shock, be sure the power supply is turned off before servicing or installing the fixture. Service should be performed by qualified personnel. 3) These instructions may not cover all details or variations. If additional information is needed, please contact Visa Lighting. PRE-INSTALLED CABLE AND CORDS 1717 West Civic Drive Milwaukee, WI 53209 414-354-6600 Design Modification Rights Reserved © Visa Lighting 2015 INSTALLATION INSTRUCTIONS: CP2072 Fixture family name: Sequence Sail LED 8" Dia Body Description: FIELD INSTALLATION INSTRUCTIONS Cable Hung Fixtures Drawing : 762037XX Rev: B Page 4 of 4 Eng: AJM Date drawn: 7/20/2015 Drawing : 762037XX Rev: B Page 4 of 4 WIRE BODY DOOR ASSEMBLY