E
L
C
I
H
E
V
R
A
P
O
S
M
N
G
A
L
N
I
P
L
L
N
SE ROTECTIO SOR
P H WIADVI
WIT
Maintenance
Menu
Previous
Current
$149.99
Next
1
Note: Before your dealership can begin to sell Mopar Vehicle Protection Plans with wiADVISOR, you must first
perform some administrative steps as outlined in the document titled: “Selling Mopar Vehicle Protection Plans
with wiADVISOR – Dealer Setup.” This document is attached with the 1.7 Release Notes, and is available in the
KnowledgeBase.
Once your dealership has completed the required setup, you will be able to use this feature to sell MVP Plans
with wiADVISOR. Additionally, wiADVISOR will handle the processing of the MVP Plan application for you! Your
dealership will no longer need to apply the contract to a VIN in DealerCONNECT.
On the “Build RO” Tab, you will see a new section on the left-hand pane titled “Eligible Mopar Vehicle Protection
Plans” located below the Triage section and above Dealer Recommended Maintenance.
Eligible MVP Plans are not immediately displayed; the user must initiate the displaying of eligible plans by clicking
the “Display” button.
Maintenance
Menu
Previous
Current
$149.99
Next
2
Once the user clicks “Display,” the status bar will momentarily display a message indicating that the list of eligible
Plans is being created.
Maintenance
Menu
Previous
Current
Next
$149.99
After a few seconds the eligible offers for the VIN, Customer Name and Mileage that are currently entered in
wiADVISOR will display in the section below the header box.
3
To select an eligible MVP Plan to be added to the RO, the user simply clicks the check box next to the contract
plan, just like any other service in wiADVISOR. The Plan will then be added to the right-hand pane.
A “Promo Code” box will be available for those dealers participating in any special promotions or contests
pertaining to the sale on MVP Plans. This code will be added to the contract application when wiADVISOR
attempts to add the new Plan to the VIN.
Maintenance
Menu
Previous
Current
$149.99
Next
4
In addition to the Eligible MVP Plans being displayed on the left-hand pane of the “Build RO” tab, the user can
also generate a new PDF document which will contain the Eligible Offers and Plan details by clicking the button at
the top of the screen labeled “MVP Plans”.
(This report is also available at the end of the wiADVISOR Push with the other documents, but ONLY if the user
clicked the “Display” button while on the “Build RO” tab, or clicked the “MVP Plans” button at the top of the
screen. The link to the report will not appear after the wiADVISOR push if neither of these actions were taken
during the write-up process.)
Maintenance
Menu
Previous
Current
$149.99
Next
5
Example of the Eligible MVP Plans PDF document:
Maintenance
Menu
Previous
Current
$149.99
Next
6
Once the user completes the write-up process and pushes the RO, wiADVISOR will attempt to add the selected
contract(s) to the VIN. If successful, no error message will be displayed on the final screen.
Maintenance
Menu
Previous
Current
$149.99
Next
7
ERROR MESSAGES AND SPECIAL CASES
Vehicle Not Eligible for a Service Contract: If the vehicle is not eligible for a service contract, the message
below will be shown when the user clicks “Display”:
Maintenance
Menu
Previous
Current
Next
$149.99
Mileage Discrepancy Error: If a user attempts to view the Eligible MVP Plans but has a mileage currently entered
that is less than a previously recorded mileage, the error message below will display. The user will not be able
to view or select any contracts in this case. If the original mileage entered was an error, updating to a higher
mileage and then re-clicking “Display” will show the Eligible Contracts, if any apply.
8
Application Rejected Error Message: In some rare cases a contract application may be rejected. This is typically
seen if a user attempts to add 2 or more contracts to a VIN on the same RO that are not compatible together.
It is important to note that if a user sees this message after completing the push, the contracts that were selected
were NOT applied to the VIN. Dealers will need to use DealerCONNECT to add the contract(s), and may need to
adjust the RO in your DMS accordingly. All contracts that were selected will push into your DMS (if applicable)
regardless of whether or not the contract application is successful. This is a limitation of the system and cannot
be changed.
Also it should be noted that in this rare circumstance, wiADVISOR Reporting may be inaccurate in cases where
contracts are pushed to an RO but are not actually sold to the customer. The Reporting will not account for
contracts failing to be applied to a VIN.
Maintenance
Menu
Previous
Current
Next
$149.99
If you have any questions, please contact us at 855-wiADVISOR (855-942-3847) or support@wiADVISOR.com.
For assistance with MVP Plan Eligibility, please contact the MVP Dealer Sales Hotline at 800-541-4612.