Chain Drives 08 Chain Drives 08 198 Renold Transmission Chain ™ High Performance Chain Drives 18 Premier Standard All Purpose Chain Maintenance Free Stainless Steel Corrosion Resistant Hydro-Service Corrosion Resistant ™ Sovereign Abrasion Resistant Roll-Ring Chain Tensioner ™ ™ Contact Brammer on 0870 240 2100 Chain Drives 199 Unique high performance chain 8 Up to 6 times longer working life Chain Drives BS CHAIN SIZES Unbeatable wear and fatigue resistance Designed to deliver maximum return Initial wear life improved by 50% Improved fatigue resistance Plate and connecting link design optimizes stress distribution and fatigue performance. Synergy® performs, on average, 30 percent better than other brands under repeated shock loading and continual heavy loads. Better wear resistance Independent tests show Renold Synergy® performed up to six times better than the highest quality competitor’s chain. Built to perform Each component of Renold Synergy® is engineered to perfection using cutting edge design tools such as Finite Element Analysis (FEA). It all adds up to chain performance that exceeds the sum of its parts. BS CHAIN SIZES Simplex 200 Connecting links Brammer BS Order Code ISO No. Pitch inch 26 107 110038X10FT:REN 110046X10FT:REN 110056X10FT:REN 110066X10FT:REN 110088X10FT:REN 110106X10FT:REN 110127X10FT:REN 06B-1 08B-1 10B-1 12B-1 16B-1 20B-1 24B-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer BS Order Code ISO No. Pitch inch 26 107 114038X10FT:REN 114046X10FT:REN 114056X10FT:REN 114066X10FT:REN 114088X10FT:REN 114106X10FT:REN 114127X10FT:REN 06B-2 08B-2 10B-2 12B-2 16B-2 20B-2 24B-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 - Everything you need – when you need it – Tel: 0870 240 2100 S30 ANSI CHAIN SIZES Unique high performance chain Up to 6 times longer working life Unbeatable wear and fatigue resistance Designed to deliver maximum return Initial wear life improved by 50% Improved fatigue resistance Plate and connecting link design optimizes stress distribution and fatigue performance. Synergy® performs, on average, 30 percent better than other brands under repeated shock loading and continual heavy loads. Better wear resistance Independent tests show Renold Synergy® performed up to six times better than the highest quality competitor’s chain. Chain Drives 18 Built to perform Each component of Renold Synergy® is engineered to perfection using cutting edge design tools such as Finite Element Analysis (FEA). It all adds up to chain performance that exceeds the sum of its parts. ANSI CHAIN SIZES Simplex Connecting links Brammer ANSI Order Code ANSI No. Pitch inch 26 107 129037X10FT:REN 119047X10FT:REN 119057X10FT:REN 119067X10FT:REN 119087X10FT:REN 119107X10FT:REN 119127X10FT:REN 35-1 40-1 50-1 60-1 80-1 100-1 120-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer ANSI Order Code ANSI No. Pitch inch 26 107 125037X10FT:REN 115047X10FT:REN 115057X10FT:REN 115067X10FT:REN 115087X10FT:REN 115107X10FT:REN 115127X10FT:REN 35-2 40-2 50-2 60-2 80-2 100-2 120-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 - 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 Contact Brammer on 0870 240 2100 S30 Chain Drives 201 Our leading standard steel transmission chain 8 Excellent wear resistance Chain Drives BS CHAIN SIZES Wide waisted GP plate shape Fatigue performance rated as ISO + 60% Guarantee of 15,000 hours End-softened, spin riveted pin for easy cutting 3/8” to 4” pitch, simplex & duplex Renold’s unique control over pin / bush contact makes sure that wear life exceeds other brands. Little initial chain adjustment is therefore required. Renold roller chain is highly fatigue resistant, giving up to four times the life of other leading competitor chains. Breaking loads exceed the minimum requirements of the international standards. Renold’s end-softened pin and spin rivet help to minimise downtime. All you need is a Renold pin extractor and you can disassemble Renold roller chain in seconds; no need to grind the head of the pin, no need for lengthy downtime. BS CHAIN SIZES Simplex 202 Connecting links Brammer BS Order Code ISO No. Pitch inch 26 107 06B-1x10FT:REN 08B-1x10FT:REN 10B-1x10FT:REN 12B-1x10FT:REN 16B-1x10FT:REN 20B-1x10FT:REN 24B-1x10FT:REN 06B-1 08B-1 10B-1 12B-1 16B-1 20B-1 24B-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer BS Order Code ISO No. Pitch inch 26 107 06B-2x10FT:REN 08B-2x10FT:REN 10B-2x10FT:REN 12B-2x10FT:REN 16B-2x10FT:REN 20B-2x10FT:REN 24B-2x10FT:REN 06B-2 08B-2 10B-2 12B-2 16B-2 20B-2 24B-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 - Nationwide coverage, delivered locally same or next day – Tel: 0870 240 2100 S30 ANSI CHAIN SIZES Our leading standard steel transmission chain Excellent wear resistance Wide waisted GP plate shape Fatigue performance rated as ISO + 60% Guarantee of 15,000 hours End-softened, spin riveted pin for easy cutting 3/8” to 4” pitch, simplex & duplex Renold’s unique control over pin / bush contact makes sure that wear life exceeds other brands. Little initial chain adjustment is therefore required. Renold roller chain is highly fatigue resistant, giving up to four times the Chain Drives 18 life of other leading competitor chains. Breaking loads exceed the minimum requirements of the international standards. Renold’s end-softened pin and spin rivet help to minimise downtime. All you need is a Renold pin extractor and you can disassemble Renold roller chain in seconds; no need to grind the head of the pin, no need for lengthy downtime. ANSI CHAIN SIZES Simplex Connecting links Brammer ANSI Order Code ANSI No. Pitch inch 26 107 35-1X10FT:REN 40-1X10FT:REN 50-1X10FT:REN 60-1X10FT:REN 80-1X10FT:REN 100-1X10FT:REN 120-1X10FT:REN 35-1 40-1 50-1 60-1 80-1 100-1 120-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer ANSI Order Code ANSI No. Pitch inch 26 107 35-2X10FT:REN 40-2X10FT:REN 50-2X10FT:REN 60-2X10FT:REN 80-2X10FT:REN 100-2X10FT:REN 120-2X10FT:REN 35-2 40-2 50-2 60-2 80-2 100-2 120-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 Contact Brammer on 0870 240 2100 - S30 Chain Drives 203 Solid extruded bush 8 Solid extruded roller Chain Drives BS CHAIN SIZES High waisted plates Wedge riveting Hardened and shot-peened plates Comprehensive European (BS) and ANSI standard ranges Renold A&S Roller Chain Renold A&S roller chain has long been recognised for its high quality and affordable reliability. It has earned a strong reputation for its excellent wear resistance, high fatigue resistance and durability and these factors have helped A&S become the most widely used chain brand in Europe. More than just a chain With its reliability and performance, A&S roller chain significantly contributes to reduced downtime and maintenance and has the ability to meet the needs of diverse applications and the continuously increasing demands of industry. To make sure that A&S chain keeps up with these increasing demands, a series of upgrades ensure that the range now offers even more performance benefits. Available in European (BS) and ANSI standard, A&S chain is available with a choice of lubricant to meet customer’s specific requirements. BS CHAIN SIZES Simplex 204 Connecting links Brammer BS Order Code ISO No. Pitch inch 26 107 06B-1X10FT:AS 08B-1X10FT:AS 10B-1X10FT:AS 12B-1X10FT:AS 16B-1X10FT:AS 20B-1X10FT:AS 24B-1X10FT:AS 06B-1 08B-1 10B-1 12B-1 16B-1 20B-1 24B-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer BS Order Code ISO No. Pitch inch 26 107 06B-2X10FT:AS 08B-2X10FT:AS 10B-2X10FT:AS 12B-2X10FT:AS 16B-2X10FT:AS 20B-2X10FT:AS 24B-2X10FT:AS 06B-2 08B-2 10B-2 12B-2 16B-2 20B-2 24B-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 - 90 Brammer Sales & Service Centres nationwide – Tel: 0870 240 2100 S30 ANSI CHAIN SIZES Solid extruded bush Solid extruded roller High waisted plates Wedge riveting Hardened and shot-peened plates Comprehensive European (BS) and ANSI standard ranges Renold A&S Roller Chain Renold A&S roller chain has long been recognised for its high quality and affordable reliability. It has earned a strong reputation for its excellent wear resistance, high fatigue resistance and durability and these factors have helped A&S become the most widely used chain brand in Europe. Chain Drives 18 More than just a chain With its reliability and performance, A&S roller chain significantly contributes to reduced downtime and maintenance and has the ability to meet the needs of diverse applications and the continuously increasing demands of industry. To make sure that A&S chain keeps up with these increasing demands, a series of upgrades ensure that the range now offers even more performance benefits. Available in European (BS) and ANSI standard, A&S chain is available with a choice of lubricant to meet customer’s specific requirements. ANSI CHAIN SIZES Simplex Connecting links Brammer ANSI Order Code ANSI No. Pitch inch 26 107 35-1X10FT:AS 40-1X10FT:AS 50-1X10FT:AS 60-1X10FT:AS 80-1X10FT:AS 100-1X10FT:AS 120-1X10FT:AS 35-1 40-1 50-1 60-1 80-1 100-1 120-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer ANSI Order Code ANSI No. Pitch inch 26 107 35-2X10FT:AS 40-2X10FT:AS 50-2X10FT:AS 60-2X10FT:AS 80-2X10FT:AS 100-2X10FT:AS 120-2X10FT:AS 35-2 40-2 50-2 60-2 80-2 100-2 120-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 - Contact Brammer on 0870 240 2100 S30 Chain Drives 205 BS CHAIN SIZES Chain Drives 8 No lubrication normally required Outside of chain totally dry-to-the-touch Nickel-plated plates Food industry-approved lubricant within sintered bush Unique food industry-approved roller coating Dimensionally interchangeable with standard chain ISO standard pin diameter, therefore standard attachments on outer links For use in hygiene-sensitive applications or situations where contamination from lubricant is to be avoided, Renold Syno chain displays all the characteristics you need from a chain. With a food industryapproved lubricant within the sintered bush, this chain will in almost all instances not need relubricating. The roller coating is also suitable for use in the food industry; a unique feature on any chain. Available in boxed 10-foot lengths from 06B to 24B and ANSI 40 to ANSI 100, simplex and duplex with a standard pin diameter, this means that Renold Syno chain is dimensionally interchangeable with standard roller chain and is even compatible with standard sprockets. With the kind of excellent wear and fatigue resistance that you expect from a Renold chain, Syno chain outlasts any competitor product promoted as low-lube or non-lube. Already tried and tested by major companies in the food sector and elsewhere, if you have to operate with minimal lubrication but can’t compromise on performance, we can boost your productivity, cut your downtime and save you time and money. BS CHAIN SIZES Simplex 206 Connecting links Brammer BS Order Code ISO No. Pitch inch 26 107 110438X10FT:REN 110446X10FT:REN 110456X10FT:REN 110466X10FT:REN 110488X10FT:REN 110506X10FT:REN 110527X10FT:REN 06B-1 08B-1 10B-1 12B-1 16B-1 20B-1 24B-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer BS Order Code ISO No. Pitch inch 26 107 11 114438X10FT:REN 114446X10FT:REN 114456X10FT:REN 114466X10FT:REN 114488X10FT:REN 114506X10FT:REN 114527X10FT:REN 06B-2 08B-2 10B-2 12B-2 16B-2 20B-2 24B-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 S11/S58 S26 S107 S12 Duplex Connecting links We work harder to save you money and downtime – Tel: 0870 240 2100 S30 ANSI CHAIN SIZES No lubrication normally required Outside of chain totally dry-to-the-touch Nickel-plated plates Food industry-approved lubricant within sintered bush Unique food industry-approved roller coating Dimensionally interchangeable with standard chain ISO standard pin diameter, therefore standard attachments on outer links For use in hygiene-sensitive applications or situations where contamination from lubricant is to be avoided, Renold Syno chain displays all the characteristics you need from a chain. With a food industryapproved lubricant within the sintered bush, this chain will in almost all instances not need relubricating. The roller coating is also suitable for use in the food industry; a unique feature on any chain. Available in boxed 10-foot lengths from 06B to 24B and ANSI 40 to ANSI 100, simplex and duplex with a standard pin diameter, this means that Renold Syno chain is dimensionally interchangeable with standard roller chain and is even compatible with standard sprockets. With the kind of excellent wear and fatigue resistance that you expect from a Renold Chain Drives 18 chain, Syno chain outlasts any competitor product promoted as low-lube or non-lube. Already tried and tested by major companies in the food sector and elsewhere, if you have to operate with minimal lubrication but can’t compromise on performance, we can boost your productivity, cut your downtime and save you time and money. ANSI CHAIN SIZES Simplex Connecting links Brammer ANSI Order Code ANSI No. Pitch inch 26 107 11 119443X10FT:REN 119453X10FT:REN 119463X10FT:REN 119483X10FT:REN 40-1 50-1 60-1 80-1 0.500 0.625 0.750 1.000 - - Brammer ANSI Order Code ANSI No. Pitch inch 26 107 11 115443X10FT:REN 115453X10FT:REN 115463X10FT:REN 115483X10FT:REN 40-2 50-2 60-2 80-2 0.500 0.625 0.750 1.000 - 12 30 12 30 S11/S58 S26 S107 S12 Duplex Connecting links S30 Contact Brammer on 0870 240 2100 Chain Drives 207 Renold Hydro-Service® Superior corrosion resistance for chain BS CHAIN SIZES Superior corrosion resistance Last as much as 30 times longer than standard carbon steel 8 Chain Drives Hexavalent chrome free 350 hours corrosion protection during salt spray tests to DIN 50021 Cold extruded, solid bush and roller delivering maximum Renold performance Plates and rollers shot peened to our exact specifications Wear and fatigue resistance that delivers maximum working life Lubrication that improves wear performance Renold Hydro-Service chain delivers superior corrosion resistance, lasting as much as 30 times longer than standard carbon steel in applications that have to deal with water or salt spray. It is ideal for wash-down environments. Hydro-Service chain is also more economical, and stronger, than stainless steel. Each component is mechanically treated prior to assembly to ensure consistent, secure protection. The surface treatment is free of hexavalent chrome, complying with legislation relating to environmental and health & safety considerations. BS CHAIN SIZES Simplex 208 Connecting links Brammer BS Order Code ISO No. Pitch inch 26 107 06B-1HSx10FT:REN 08B-1HSx10FT:REN 10B-1HSx10FT:REN 12B-1HSx10FT:REN 16B-1HSx10FT:REN 20B-1HSx10FT:REN 24B-1HSx10FT:REN 06B-1 08B-1 10B-1 12B-1 16B-1 20B-1 24B-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - Brammer BS Order Code ISO No. Pitch inch 26 107 06B-2HSx10FT:REN 08B-2HSx10FT:REN 10B-2HSx10FT:REN 12B-2HSx10FT:REN 16B-2HSx10FT:REN 20B-2HSx10FT:REN 24B-2HSx10FT:REN 06B-2 08B-2 10B-2 12B-2 16B-2 20B-2 24B-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 - 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 - FREE 24/7 technical support – Tel: 0870 240 2100 S30 Renold Hydro-Service® Superior corrosion resistance for chain ANSI CHAIN SIZES Superior corrosion resistance Last as much as 30 times longer than standard carbon steel 18 Chain Drives Hexavalent chrome free 350 hours corrosion protection during salt spray tests to DIN 50021 Cold extruded, solid bush and roller delivering maximum Renold performance Plates and rollers shot peened to our exact specifications Wear and fatigue resistance that delivers maximum working life Lubrication that improves wear performance Renold Hydro-Service chain delivers superior corrosion resistance, lasting as much as 30 times longer than standard carbon steel in applications that have to deal with water or salt spray. It is ideal for wash-down environments. Hydro-Service chain is also more economical, and stronger, than stainless steel. Each component is mechanically treated prior to assembly to ensure consistent, secure protection. The surface treatment is free of hexavalent chrome, complying with legislation relating to environmental and health & safety considerations. ANSI CHAIN SIZES Simplex Brammer ANSI Order Code ANSI No. Pitch inch 35-1HSx10FT:REN 40-1HSx10FT:REN 50-1HSx10FT:REN 60-1HSx10FT:REN 80-1HSx10FT:REN 100-1HSx10FT:REN 120-1HSx10FT:REN 35-1 40-1 50-1 60-1 80-1 100-1 120-1 0.375 0.500 0.625 0.750 1.000 1.250 1.500 Brammer ANSI Order Code ANSI No. Pitch inch 06B-2HSx10FT:REN 08B-2HSx10FT:REN 35-2HSx10FT:REN 40-2HSx10FT:REN 50-2HSx10FT:REN 60-2HSx10FT:REN 80-2HSx10FT:REN 35-2 40-2 50-2 60-2 80-2 100-2 120-2 0.375 0.500 0.625 0.750 1.000 1.250 1.500 Connecting links 26 107 26 107 11 12 30 12 30 - S11/S58 S26 S107 S12 Duplex Connecting links 11 Contact Brammer on 0870 240 2100 - S30 Chain Drives 209 Roll-Ring® Chain Tensioner Revolutionary chain tensioner 8 Installed in seconds and self adjusting Chain Drives BS CHAIN SIZES Maintenance free Works on simplex, duplex & triplex chain Available in a wide range of pitch sizes Also acts as noise damper BS CHAIN SIZES The Innovative Tensioner The innovative prize winning Roll-Ring chain tensioner is based on new principles and represents a major advance in technology. 210 Roll-Ring is an innovative chain tensioner made from a specially formulated polymer. The unique design is based upon a toothed ring that can be fitted to horizontal, vertical or diagonal drives in a matter of seconds, simply by placing it in-between the two strands of chain. When the drive is in use, the Roll-Ring deforms to an elliptical shape, due to the compression between the strands and completely absorbs any slack in the system. Roll-Ring performs the job of a tensioner and a damper in one, and is ideally suited to applications where maintenance is difficult or impossible. Part No. ISO No. Teeth Part No. ISO No. Teeth Part No. ISO No. Teeth 105 030 01 106 030 01 106 036 01 108 026 01 108 030 01 108 034 01 108 430 01 110 026 01 110 030 01 110 034 01 112 026 01 112 030 01 112 034 01 116 026 01 116 030 01 120 030 01 ISO 05 ISO 06 ISO 06 ISO 08 ISO 08 ISO 08 * ISO 10 ISO 10 ISO 10 ISO 12 ISO 12 ISO 12 ISO 16 ISO 16 ISO 20 30 30 36 26 30 34 30 26 30 34 26 30 34 26 30 30 106 030 06 108 026 06 108 030 06 108 430 06 110 026 06 110 030 06 112 026 06 112 030 06 116 026 06 116 030 06 ISO 06 ISO 08 ISO 08 * ISO 10 ISO 10 ISO 12 ISO 12 ISO 16 ISO 16 30 26 30 30 26 30 26 30 26 30 106 030 08 108 026 08 108 030 08 108 430 08 110 026 08 110 030 08 112 026 08 112 030 08 116 026 08 116 030 08 ISO 06 ISO 08 ISO 08 * ISO 10 ISO 10 ISO 12 ISO 12 ISO 16 ISO 16 30 26 30 30 26 30 26 30 26 30 Nationwide coverage, delivered locally same or next day – Tel: 0870 240 2100 Roll-Ring® Chain Tensioner ANSI CHAIN SIZES Revolutionary chain tensioner Installed in seconds and self adjusting Maintenance free Works on simplex, duplex & triplex chain Available in a wide range of pitch sizes Also acts as noise damper ANSI CHAIN SIZES The Innovative Tensioner The innovative prize winning Roll-Ring chain tensioner is based on new principles and represents a major advance in technology. Roll-Ring is an innovative chain tensioner made from a specially formulated polymer. The unique design is based upon a toothed ring that can be fitted to horizontal, vertical or diagonal drives in a matter of seconds, simply by placing it in-between the two strands of chain. Chain Drives 18 When the drive is in use, the Roll-Ring deforms to an elliptical shape, due to the compression between the strands and completely absorbs any slack in the system. Roll-Ring performs the job of a tensioner and a damper in one, and is ideally suited to applications where maintenance is difficult or impossible. Part No. ISO No. Teeth Part No. ISO No. Teeth Part No. ISO No. Teeth 106 030 01 108 026 01 108 030 01 108 034 01 108 430 01 110 026 01 110 030 01 110 034 01 112 026 01 112 030 01 112 034 01 116 026 01 116 030 01 120 030 01 ISO 35 ISO 40 ISO 40 ISO 40 * ISO 50 ISO 50 ISO 50 ISO 60 ISO 60 ISO 60 ISO 80 ISO 80 ISO 100 30 30 30 30 30 30 30 30 30 30 30 30 30 30 106 030 06 108 026 06 108 030 06 108 430 06 110 026 06 110 030 06 112 026 06 112 030 06 116 026 06 116 030 06 ISO 35 ISO 40 ISO 40 * ISO 50 ISO 50 ISO 60 ISO 60 ISO 80 ISO 80 30 26 30 30 26 30 26 30 26 30 106 030 08 108 026 08 108 030 08 108 430 08 110 026 08 110 030 08 112 026 08 112 030 08 116 026 08 116 030 08 ISO 35 ISO 40 ISO 40 * ISO 50 ISO 50 ISO 60 ISO 60 ISO 80 ISO 80 30 26 30 30 26 30 26 30 26 30 Contact Brammer on 0870 240 2100 Chain Drives 211 Renold Conveyor Chain Chain Drives 8 Standard stock range of BS conveyor chain, available ex-stock. 3,000 to 30,000lb chains produced in our dedicated UK manufacturing cell. • Fast availability of standard integral attachments 212 • Standard cast iron sprockets available ex-stock • Supporting this standard range we also have the capability to supply specials and customdesigned products. 90 Brammer Sales & Service Centres nationwide – Tel: 0870 240 2100 THE COMPREHENSIVE POWER TRANSMISSION PRODUCTS PROVIDER Chain Gears Couplings Services & Exclusive Technologies Design and Manufacturing Expertise • Technical support helpline - Advice on selection, calculations based on your application • Online chain selector • Onsite technical advice - Installation assistance / supervision • SmartProducts: unique wear and load monitoring technology exclusive to Renold • Roll-Ring chain tensioner, fit it in seconds • Attachment chain service - Quick turnaround, wide range of stock attachments • Online training information and guidance • The ability to respond to individual customer needs with bespoke designs • An unrivalled depth of knowledge and experience in chain manufacturing Check out our Chain Selector www.renoldchainselector.com 18 Chain Drives A GROUP OVERVIEW Comprehensive Range • Market-leading range of standard chain • Solution products designed with application and environmental requirements in mind – see the product listing opposite. See How to Cut Chain Easily www.renoldpinextractor.com Contact Brammer on 0870 240 2100 Chain Drives 2213 Chain Drives 8 Tsubakimoto is the world’s premier manufacturer of power transmission products including high quality ANSI and BS roller, conveyor and engineering chains and associated products such as cam clutches and linear actuators. It spends more on R&D than any other chain manufacturer in the world and offers the highest levels of engineering in all of its products. Tsubaki believes that reliability is the key to productivity and profitability, which is why it manufactures chain which is designed 214 to outperform the competition in even the harshest of industrial environments. This meets its Eco Eco philosophy of offering economical and ecological benefits to its customers with every single sale. The company has a global network of production and storage facilities which all operate on a policy of economical and ecological efficiency. This is most notable in its flagship Kyotanabe Plant in Japan which is responsible for developing new chain technologies and manufacturing product for distribution globally. Tsubaki aims to be a leading company in the global markets for its products and plans to achieve this through excellence in manufacturing for customers around the world. It offers the best value to customers around the world by capitalising on its technical strengths in power transmission products and material handling systems. We work harder to save you money and downtime – Tel: 0870 240 2100 Roller Chain Guide Start your product selection here SS Coated Steel or Stainless Steel Chain? Yes Attachment Chain Do you require corrosion resistance? CS Yes Are you able to lubricate? No No Do you require corrosion resistance? Yes Coated Steel or Stainless Steel Chain? No Chain: GT4 WINNER is the most advanced chain in the European market. Unique features are solid bushing with lubrication grooves, ring coined connecting links, and centre sink pin for easy dissassembly. Typical applications: Suitable for all general applications. CS SS 18 Chain Drives Roller Chain Chain: Tsubaki is the pioneer in developing lube free chain. Lambda features an oil impregnated bush in combination with a special coated pin for long-term internal lubrication is the secret to Lambda’s economic long life and wear resistance. This chain also comes with our standard features such as ring coined connecting links and easy break style pin head. Typical applications: Food, Packaging, Printing, Sawmill, Textile. Limitations: Max. Temp. 150degC, Max. Speed 50-160m/min * Limitations: Application specific, please contact Tsubaki * ANSI 3&&KDLQ (QJLQHHULQJSODVWLF FRPELQDWLRQFKDLQ Chain: Tsubaki G7 ANSI chain features the same benefits as our BS GT4 WINNER chain such solid bushing and lube grooves to increase chain life by reducing wear. The G7 chain also offers an increased kW rating. Chain: Plastic combination chain uses a stainless steel outer link, and a resilient plastic inner link to reduce weight and improve wear life without lubrication. A clean and long lasting alternative to stainless steel chain. Typical applications: Suitable for all general applications. Typical applications: Food, Pharmaceutical, Packaging, Healthcare. Limitations: Application specific, please contact Tsubaki * Limitations: Max. Temp. range -20 to 80degC, Max. Speed 70m/min. Need more capacity? 1(3 1HZ(QYLURQPHQWDO3ODWLQJ Chain: Tsubaki NEP chain is coated to give high corrosion protection to carbon steel chain. The chain is eco-friendly and meets RoHS requirements, whilst maintaining 100% the strength of the chain. Typical applications: Food, Packaging, Utilities. Limitations: Application specific, please contact Tsubaki * LAMBDA N.E.P. Chain: Plastic combination chain uses a stainless steel outer link, and a resilient plastic inner link to reduce weight and improve wear life without lubrication. A clean and long lasting alternative to stainless steel chain. Typical applications: Food, Packaging, Utilities. Limitations: Avoid heavy water contact. Stainless Steel Chain Chain: Tsubaki leads the stainless steel chain range with our standard SUS304 grade, a higher transmission capacity is achieved by our precipitation hardened AS grade, and special SUS316 NS grade offers the highest corrosion resistance in stainless steel chains. Typical applications: Food, Packaging, Medical. Heavy & SUPER Series Chain: Tsubaki Heavy and SUPER series chains offer increased transmission capacity, whilst remaining compatible with ANSI standard sprockets. Special treatments such as ball drifting, quad riveting, and shot peening are used to increase fatigue resistance. Typical applications: Lifting, construction and aggregate industries. Limitations: Application specific, please contact Tsubaki * Limitations: Lower transmission capacity than equivalent steel chain. * Contact Tsubaki as the application requires further investigation. Contact Brammer on 0870 240 2100 Chain Drives 215 TSUBAKI GT4 Winner: Standard Roller Chain TSUBAKI, the world’s largest and most advanced manufacturer of chain has 8 BS/DIN standard roller Chain Drives released a new 4th generation chain. The latest generation chain, branded Tsubaki GT4 Winner hosts a number of manufacturing and material developments. Repeated testing and field data indicate that wear between the bearing parts is a primary limiting factor in overall chain life, particularly in externally lubricated chain types such as BS/DIN standard roller chain. TSUBAKI has committed significant amounts of research and development to making improvements in this area, to reduce wear and chain elongation over a longer period of time-even for standard drive roller chain. Four Key Features 1. Pre Lubrication Lube Groove (LG) TSUBAKI’s new BS/DIN series roller chain utilise a new production technique to manufacture a seamless bush with grooves incorporated on the inner surface. The lubegrooved (LG) bush holds oil at the point of contact where the chain needs it most, providing an internal reservoir for lubricant. The result is a chain that lasts longer with lower maintenance costs over the lifetime of the chain. 216 2. Seamless Bush > Perfectly Cylindrical The new Tsubaki BS/DIN series chain has a seamless bush with a very precise cylindrical profile and surface finish resulting in better surface contact between the pin and bush along with improved lubricant retention. 3. Easy dis-assembly > Centre Sink Rivet With Tsubaki’s design of rivet head the chain is easily dis-assembled with an additional benefit being that in the event of the chain being overloaded, the markings on the rivet head will identify pin rotation. 4. Increased Transmission Capacity > Ring Coining The Ring Coined connecting link allows the chain to be specified up to its full kW rating. The precision and strength achieved on these components is far beyond that of competitor’s offerings. The typical standard slip-fit connecting link is usually much weaker than the other links. Tsubaki’s Ring Coin technology has overcome that. CO2 Reduction Tsubaki takes its environmental responsibility very seriously in its state-of-the-art production facilities. The new BS/DIN series chain contributes significantly to reducing CO2 emissions due to the greatly extended replacement frequency. FREE 24/7 technical support – Tel: 0870 240 2100 T L2 d1 b1 pt T d2 t L1 L2 b1 L1 t %6*7:,11(567$1'$5'52//(5&+$,1 H d2 d1 p 18 L1 pt T b1 pt L2 L1 L t Chain Drives L1 p d2 OL d1 2POL *7:LQQHU 'LPHQVLRQVLQPP 3LQ 768%$., &KDLQ1R 05B-1:TSUB 56% 05B-2:TSUB 56% 05B-3:TSUB 56% 06B-1:TSUB 5)% 06B-2:TSUB 5)% 06B-3:TSUB 5)% 08B-1:TSUB 56% 08B-2:TSUB 56% 08B-3:TSUB 56% 10B-1:TSUB 56% 10B-2:TSUB 56% 10B-3:TSUB 56% 12B-1:TSUB 56% 12B-2:TSUB 56% 12B-3:TSUB 56% 16B-1:TSUB 56% 16B-2:TSUB 56% 16B-3:TSUB 56% 20B-1:TSUB 56% 20B-2:TSUB 56% 20B-3:TSUB 56% 24B-1:TSUB 56% 24B-H-1:TSUB 56%+ 24B-2:TSUB 56% 24B-3:TSUB 56% 28B-1:TSUB 56% 28B-2:TSUB 56% 28B-3:TSUB 56% 32B-1:TSUB 56% 32B-2:TSUB 56% 32B-3:TSUB 56% 40B-1:TSUB 56% 40B-2:TSUB 56% 40B-3:TSUB 56% 48B-1:TSUB 56% 48B-2:TSUB 56% 48B-3:TSUB 56% /LQN3ODWH 3LWFK 5ROOHU 'LDPHWHU ,QQHU :LGWK 'LDPHWHU /HQJWK /HQJWK /HQJWK S G E G / / / µ µ µ µ µ µ µ µ µ µ µ µ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ontact Brammer on 0870 240 2100 Chain Drives 217 Lambda Lube Free Roller Chain Chain Drives 8 Tsubaki’s Lambda Chains were the first in the industry to use a special oil-impregnated bush. Since their launch in 1988, they have been adopted for diverse industries and applications, and their performance has been highly rated. Tsubaki has a wide line-up of lube-free, long life products that help customers reduce costs. Technical Evolution As a pioneer in the lube-free chain market, Tsubaki will reveal some of the key elements behind Lambda’s outstanding performance: Sintered Bush A special oil-impregnated sintered bush in combination with a special coated pin for long-term internal lubrication is the secret of Tsubaki Lambda’s long economic life and wear resistance. Easy Cutting BS Lambda chain can be disassembled quick and safely with an original Tsubaki Chain Tool without damaging the bushes (RS08B-LM-1 to RS16B-LM-1). For applications in the food industry, Tsubaki can supply Lambda chain with bushes impregnated with food grade lubricating oil (NSF-H1 and H3 certified). When an application needs water wash downs or is exposed to moisture, and lubrication is not possible or desirable, Lambda N.E.P. is most efficient. Advantages Tsubaki has enhanced the Lambda with the following advantages: Save Maintenance Costs No expensive labour costs as it is not required to manually lubricate this chain. Save Purchasing Costs Lower frequency of purchasing due to the high quality of the chain and it’s long economic life. No purchasing of lubricants or lubrication systems necessary. Higher Productivity No unforeseen downtime due to chain breakdown. Less time required for maintenance and therefore more time for production. Inter-Changeability Chains: • BS Lambda: BS Lambda Chains are fully interchangeable with standard BS roller chains. • ANSI Lambda: Only simplex ANSI Lambda is interchangeable with standard ANSI roller chain. However, as the pins are longer than those of the standard ANSI roller chain, please make sure that there is no interference with the machine. Sprockets: • BS Lambda: Standard BS roller chain sprockets can be used. However, due to the extended lifetime of BS Lambda chain, Tsubaki recommends to install sprockets with hardened teeth in every Lambda application. • ANSI Lambda: Only simplex ANSI roller chain sprockets are interchangeable. Multi strand sprockets need to be customised due to the thickness of the roller link plates. Due to the extended lifetime of ANSI Lambda chain, Tsubaki advises to install sprockets with hardened teeth in every Lambda application. Environmental Friendly Applications run clean thus reducing the risk of contaminating products, machines, floor etc. Patented Ring Coining Process Breakage of the chains connecting link is no issue at Tsubaki thanks to this unique feature. By applying the patented Ring Coining process, Tsubaki generates a cold deformation around the pin hole of the connecting link plate. This results in residual stress around the pin hole and thereby adds strength. By using this process transmission capacity is 100% of the base chain. Special Oil Impregnated Sintered Bush Special Coated Pin Special Environments Tsubaki Lambda has outstanding performance in temperatures up to 150°C. For temperatures above 150°C Tsubaki has a special high-temperature Lambda available. Please contact Tsubaki for more detailed information. 218 Roller Ring Coining Nationwide coverage, delivered locally same or next day – Tel: 0870 240 2100 T pt t L1 b1 d1 T L2 b1 L1 t L2 d2 H d2 d1 p L L1 p OL 2POL BS LAMBDA Chain BS LAMBDA CHAIN Chain Drives L1 18 Dimensions in mm Pin 06B-1Lambda:TSUB RF06B-LM-1 06B-2Lambda:TSUB RF06B-LM-2 08B-1Lambda:TSUB RS08B-LM-1 08B-2Lambda:TSUB RS08B-LM-2 10B-1Lambda:TSUB RS10B-LM-1 10B-2Lambda:TSUB RS10B-LM-2 12B-1Lambda:TSUB RS12B-LM-1 12B-2Lambda:TSUB RS12B-LM-2 16B-1Lambda:TSUB RS16B-LM-1 16B-2Lambda:TSUB RS16B-LM-2 20B-1Lambda:TSUB RS20B-LM-1 20B-2Lambda:TSUB RS20B-LM-2 24B-1Lambda:TSUB RS24B-LM-1 24B-2Lambda:TSUB RS24B-LM-2 Roller Diameter Pitch TSUBAKI Chain No. p 9.525 (3/8”) Inner Width Diameter d1 b1 d2 6.35 5.72 3.28 12.70 (1/2”) 8.51 7.75 4.45 15.875 (5/8”) 10.16 9.65 5.08 19.05 (3/4”) 12.07 11.68 5.72 25.40 (1”) 15.88 17.02 8.28 31.75 (1 1/4”) 19.05 19.56 10.19 38.10 (1 1/2”) 25.40 25.40 14.63 Length Link Plate Length Length L1 L2 L 6.10 11.20 8.40 15.30 9.55 17.85 11.10 20.85 17.75 33.55 19.90 38.25 26.65 50.80 7.70 12.80 10.00 16.90 11.25 19.55 13.00 22.75 19.95 35.75 23.10 41.45 31.85 56.00 15.10 25.90 18.60 34.50 20.80 39.40 24.40 45.90 39.30 73.40 46.60 84.60 61.70 112.80 Thickness Thickness Height T t H (max) 1.30 1.00 8.20 1.60 1.60 12.00 1.50 1.50 14.70 1.80 1.80 16.10 4.00 3.20 21.00 4.40 3.40 26.40 6.00 5.60 33.40 Min. Tensile Strength acc. to Transverse ISO 606 Pitch Approx. Mass pt kN kg/m 10.24 13.92 16.59 19.46 31.88 36.45 48.36 8.9 16.9 17.8 31.1 22.2 44.5 28.9 57.8 60.0 106.0 95.0 170.0 160.0 280.0 0.39 0.75 0.70 1.35 0.95 1.85 1.25 2.50 2.70 5.40 3.85 7.65 7.45 14.65 Note: 1. Connecting links are clip type for sizes up to RS16B-LM, and cotter type for sizes RS20B-LM to RS24B-LM. 2. RF06B-LM chain has flat shaped link plates. 3. Intermediate plate of RF06B-LM-2 and RS08B-LM-2 is a solid plate. 4. Centre sink riveting is applied for RS08B-LM-1 to RS16B-LM-1. Double stake riveting is applied to all other sizes including multi-strand chain. 5. Warning: previous generations of Lambda chain can not be connected with the above chains due to different dimensions. 6. When a single pitch offset link is used, please calculate a 35% reduction of the fatigue strength. 7. Also available in N.E.P. specification. Contact Brammer on 0870 240 2100 Chain Drives 219 BS Chain For Corrosive Environments BS standard roller chain) and lightweight chain (50% lighter than BS standard roller chain). Working temperature range: -20°C to +80°C. Corrosion Resistant Chain (Stainless Steel base) Corrosion Protected Chain (Carbon Steel base) BS PC Engineering Plastic Combination Chain The pins and pin link plates of these chains are made of SUS304 (spring clips SUS301). Engineering plastic (white) is used for the inner link. This combination makes it a lube-free, low noise (5 dB lower than BS N.E.P. New Environmental Plating Chain BS N.E.P. Chain is a TSUBAKI BS chain that has undergone a special surface treatment. The link plates, bushes and bearing pins have a special three stage layer applied in order to provide the maximum protection from the operating or environmental conditions. (Spring clips are SUS301). N.E.P. Rollers have a special coating designed to resist the corrosive conditions as well as the severe dynamic contact between roller and sprocket. BS SS Stainless Steel Chain All basic components of this chain are made of Stainless Steel SUS304 (except the spring clips, which are made of SUS301). This chain can be used in special environments such as underwater, acidic and alkaline applications. It can also be used in high and low temperatures (-20°C to +400°C). SUS304 is only marginally magnetic, which is the result of the coldforging process. This chain is suitable for use in environments exposed to seawater, acidrain and other adverse weather conditions. This chain does not contain any chemically hazardous substances such as Hexavalent Chromium, Lead, Cadmium and Mercury as regulated by RoHS√. The kilowatt ratings are the same as those of the corresponding BS chain with a working temperature range: -10°C to +150°C. Above +60°C a special high-temperature lubrication is required. Of course, BS LAMBDA N.E.P. chain is also available. √ RoHS= Restriction of Hazardous Substances T L2 b1 t L1 Chain Drives 8 Whether your operation requires a sanitary environment, is exposed to corrosive chemicals, is heated to extreme temperatures, runs through a freezer, is exposed to the outdoors or is affected by excessive moisture: our specially designed and tested chains will outlast your current chains and contribute to a cost effective application. d2 H d1 p p BS PC CHAIN BS PC Chain Dimensions in mm Pin TSUBAKI Chain No. 06B-1PC:TSUB RF06B-PC-1 08B-1PC:TSUB RF08B-PC-1 10B-1PC:TSUB RF10B-PC-1 12B-1PC:TSUB RF12B-PC-1 220 Pitch p 9.525 12.70 15.875 19.05 (3/8”) (1/2”) (5/8”) (3/4”) Bush Diameter d1 6.35 8.51 10.16 12.07 Inner Width b1 5.72 7.75 9.65 11.68 Diameter d2 3.28 4.45 5.08 5.72 Length L1 6.50 8.35 9.55 11.10 Link Plate Length L2 7.25 10.05 11.25 13.00 Thickness T 1.30 1.60 1.50 1.80 Thickness t 1.00 1.50 1.50 1.80 Height H (max) 8.60 12.00 14.70 16.10 Max. Allowable Load acc. to Tsubaki kN 0.20 0.46 0.53 0.70 90 Brammer Sales & Service Centres nationwide – Tel: 0870 240 2100 Approx. Mass kg/m 0.23 0.40 0.51 0.67 b1 T L2 d1 b1 T pt t L1 t L1 L2 d2 H d2 d1 p 18 Chain Drives L1 pt T b1 pt L2 L1 L t L1 p d2 OL d1 2POL BS SS CHAIN BS SS Chain Dimensions in mm Pin TSUBAKI Chain No. 06B-1SS:TSUB RF06B-SS-1 06B-2SS:TSUB RF06B-SS-2 08B-1SS:TSUB RS08B-SS-1 08B-2SS:TSUB RS08B-SS-2 08B-3SS:TSUB RS08B-SS-3 10B-1SS:TSUB RS10B-SS-1 10B-2SS:TSUB RS10B-SS-2 10B-3SS:TSUB RS10B-SS-3 12B-1SS:TSUB RS12B-SS-1 12B-2SS:TSUB RS12B-SS-2 12B-3SS:TSUB RS12B-SS-3 16B-1SS:TSUB RS16B-SS-1 16B-2SS:TSUB RS16B-SS-2 20B-1SS:TSUB RS20B-SS-1 Roller Diameter d1 Pitch p 9.525 Inner Width b1 Diameter d2 (3/8”) 6.35 5.72 3.28 12.70 (1/2”) 8.51 7.75 4.45 15.875 (5/8”) 10.16 9.65 5.08 19.05 (3/4”) 12.07 11.68 5.72 25.40 (1”) 15.88 17.02 8.28 31.75 (1 1/4”) 19.05 19.56 10.19 Length L1 6.50 11.60 8.35 15.30 22.25 9.55 17.85 26.20 11.10 20.90 30.65 17.75 33.55 20.10 Link Plate Length L2 7.25 12.30 10.05 17.00 23.95 11.25 19.55 27.80 13.00 22.70 32.60 19.95 35.75 23.10 Length L 15.45 28.85 20.05 34.60 48.60 22.90 39.40 56.00 26.70 46.10 65.60 38.90 73.80 48.40 Thickness T Thickness t Height H (max) 1.30 1.00 8.20 1.50 1.50 12.00 1.50 1.50 14.70 1.80 1.80 16.10 4.00 3.20 21.00 4.50 3.50 26.00 Transverse Pitch pt 10.24 13.92 13.92 16.59 16.59 19.46 19.46 31.88 - Max. Allowable Load acc. to Tsubaki kN 0.28 0.56 0.50 1.00 1.50 0.67 1.34 2.01 0.89 1.78 2.67 2.10 4.20 2.95 Approx. Mass kg/m 0.39 0.75 0.70 1.35 2.00 0.95 1.85 2.80 1.25 2.50 3.80 2.70 5.40 3.85 BS N.E.P. CHAIN Dimensions in mm Pin TSUBAKI Chain No. 06B-1NEP:TSUB RF06B-NEP-1 06B-2NEP:TSUB RF06B-NEP-2 08B-1NEP:TSUB RS08B-NEP-1 08B-2NEP:TSUB RS08B-NEP-2 10B-1NEP:TSUB RS10B-NEP-1 10B-2NEP:TSUB RS10B-NEP-2 12B-1NEP:TSUB RS12B-NEP-1 12B-2NEP:TSUB RS12B-NEP-2 16B-1NEP:TSUB RS16B-NEP-1 16B-2NEP:TSUB RS16B-NEP-2 20B-1NEP:TSUB RS20B-NEP-1 20B-2NEP:TSUB RS20B-NEP-2 24B-1NEP:TSUB RS24B-NEP-1 Roller Diameter d1 Inner Width b1 (3/8”) 6.35 5.72 3.28 12.70 (1/2”) 8.51 7.75 4.45 15.875 (5/8”) 10.16 9.65 5.08 19.05 (3/4”) 12.07 11.68 5.72 25.40 (1”) 15.88 17.02 8.28 31.75 (1 1/4”) 19.05 19.56 10.19 38.10 (1 1/2”) 25.40 25.40 14.63 Pitch p 9.525 Diameter d2 Length L1 6.35 11.43 8.40 15.30 9.55 17.85 11.20 20.85 17.75 33.55 19.90 38.25 26.65 Link Plate Length L2 7.65 12.57 10.00 16.90 11.25 19.55 13.10 22.75 19.95 35.75 23.10 41.45 31.85 Length L 14.20 18.40 33.60 21.10 39.40 24.80 46.30 38.90 73.80 46.95 84.85 62.00 Contact Brammer on 0870 240 2100 Thickness Thickness T t 1.30 1.00 1.60 1.60 1.50 1.50 1.80 1.80 4.00 3.20 4.40 3.40 6.00 5.60 Min. Tensile Strength Transverse acc. to Height ISO 606 Pitch H (max) pt kN 8.9 8.20 10.24 16.9 17.8 11.80 13.92 31.1 22.2 14.70 16.59 44.5 28.9 16.10 19.46 57.8 60.0 21.00 31.88 106.0 95.0 26.00 36.45 170.0 33.44 160.0 Min. Tensile Av. Tensile Strength Strength acc. to Approx. acc. to Tsubaki Mass Tsubaki kN kN kg/m 9.0 9.9 0.39 17.0 18.7 0.75 19.0 20.9 0.70 32.0 35.2 1.35 23.0 25.3 0.95 44.5 49.0 1.85 31.0 34.1 1.25 61.0 67.1 2.50 70.0 77.0 2.70 128.0 141.0 5.40 98.1 108.0 3.85 197.0 217.0 7.65 167.0 184.0 7.45 Chain Drives 221 Introduction to TSUBAKI Attachment Chain In the world of attachment chain TSUBAKI is the manufacturer you require to assure smooth operation. Whether your application requires attachments or extended pins in Carbon Steel, N.E.P., Nickel Plating or Stainless Steel, TSUBAKI is your partner. TSUBAKI’s maintenance Chain Drives 8 free solution, LAMBDA, is also available with a wide range of attachments. When starting with a completely new design, TSUBAKI can tailor make an attachment chain for you in any specification. Attachment Chain Structure k Pin Lin Fit Press Fit Press Bush r Rolle r Rolle Fit Press Pin t Link Offse it Slip F k Pin g Lin c e tin n n o C Fit Press Bush r Rolle r Rolle it Slip F p g Cli Sprin te k Pla Pin Lin it Slip F r Cotte Base Pin k g Lin ectin Conn Chain t Link Offse Standard Product Range The product range for our standard attachment chains is: • BS Single Pitch Standard chain + standard attachments • ANSI Single Pitch Standard chain + standard attachments • ANSI Single Pitch HP Hollow Pin chain • ANSI Single Pitch CU Curved chain • ANSI Double Pitch Standard chain + standard attachments • ANSI Double Pitch HP Hollow Pin chain 222 We work harder to save you money and downtime – Tel: 0870 240 2100 late Link P Link Match & Tag Service: High Accuracy, Narrow Tolerance Service Tolerances so for customers with specific application When chains have to run in parallel for conveying purposes in for instance packaging machines or when a minimum of difference in chain length is required in lifting applications (accumulator towers in the steel and carpet industry) requirements, we are able to supply chains with a specific length tolerance, or even pairs & multiple chains length matched TSUBAKI excels in quality performance. We can guarantee a maximum chain length difference of 0.50 mm independent of the total chain length demanded by our customers! and tagged in the same way for easy identification and installation. This is as 1A 2A 2B measurement equipment (the “Matchy”) kept 1B a result of the sophisticated chain length 18 Chain Drives For TSUBAKI, quality is second nature- and in house within the European headquarters with supply times for such chains kept to a minimum-ideal for distributors, final consumers and OEM customers alike. Custom Made Attachments Canning Bookbinder Packaging Tsubaki Gripper Chain New solution for the thermoforming process found with Tsubaki’s wide range of ‘Gripper’ chains. Tsubaki has launched a new range of ‘gripper’ chains to be used for thermoforming in various sectors including food, electrical and medical packaging. Whereas conventional gripping attachments often open vertically, Tsubaki’s range opens to the side as well which provides a larger opening preventing jams and making loading easier. This innovative solution is available with many variations of transmission chain, including Tsubaki’s unique Lambda lube-free chain. Offering extended chain life and minimal maintenance Tsubaki’s gripper chain offers a fresh, new option for thermoforming. Contact Brammer on 0870 240 2100 Chain Drives 223 Performance Through Innovation Chain Drives 8 Lube Free Series Drive Chain Series GT4 Winner LAMBDA Chain • Unique Lube Groove Bush • Absolutely no Lubrication Required • Longer Wear Life - Lower CO2 Emission • Longer Wear Life • High Transmission Capacity • Clean Handling & Running • Easy Disassembly • Higher Production Output • Accuracy of Chain Length Tolerance & Reduced Maintenance • ANSI LAMBDA KF Series now available (usable at high temperatures up to 230°C and suitable for food product applications) Corrosion Resistant Series Corrosion Protected Series Engineering Plastic Chain N.E.P. Chain • Lube Free Operation • Innovative Surface Treatment • Cleaner & Quieter Operation • Superior Corrosion Resistance • Easy Maintenance • Environmentally Friendly • Alternative to Stainless Steel Chain Mechanical Components Industry Specific Cam Clutches (Freewheel) TSUBAKI’s product range and service • Full European Range capabilities are amongst the best in the • For Indexing, Backstopping business, from standard attachments & Over-running Applications • From as low as 6 Nm up to 686.000 Nm Torque Capacity • Available from Stock through to specific industry applications. For example: Gripper chain - for form, fill & vacuum seal wrapping industry. Specialist attachments and specific matched length tolerance chains are available to meet your production schedules. 224 FREE 24/7 technical support – Tel: 0870 240 2100 TSUBAKI: Value Added Services Installation Training Services TSUBAKI offers technical training packages tailored to suit your needs. From a simple introduction to chain and installation basics; through to chain selection, advanced failure analysis and application specific advice; TSUBAKI can partner with apprentices, maintenance engineers, and designers to ensure its wealth of experience is available. 18 Chain Drives TSUBAKI engineers can support installation projects from initial quotation stage, through on-site support during installation and then to final sign off at commission. TSUBAKI products offer best value for money when correctly installed, hence our support during this critical stage. Surveying TSUBAKI can support chain users by providing a site survey of their entire plant. This ensures the ordering of complex chain is made simple by an easy-to-use survey database. TSUBAKI wants this to be an effective business tool so uses simple language to identify chain and attachment detail. The survey results can also help reduce your overall stock level and further reduce cost by identifying and consolidating common chain types. Chain Analysis TSUBAKI can analyse any returned chain to make a comprehensive and easy-to-follow report. We can often recommend TSUBAKI products that will offer further application benefits. Chain Selection Condition Based Monitoring Service TSUBAKI offers regular and scheduled site visits to monitor its chain’s performance. Customers receive a detailed report recommending the necessary actions to ensure best possible performance and value. Contact Brammer on 0870 240 2100 TSUBAKI has experience of many application types and unique machine designs. We can offer a full chain selection package, working directly with engineers and designers to ensure the product specified is the ‘perfect fit’ for your needs. Chain Drives 225 Complementary Products Chain Drives 8 Tsubaki’s offers the most complete and versatile selection of one-way clutches in the global industry. Cam Clutches are precision devices which lock the inner- and outer races, through a wedging action of cams, to transmit torque in one direction of rotation and overrun in the opposite direction. These units are often referred to as freewheels, sprag clutches, overrunning clutches, backstops or one-way clutches, depending upon on the application for which they are used. Tsubaki Roller Chain Coupling The Tsubaki Roller Chain Coupling is a flexible coupling of amazingly simple construction. It consists of the combination of one coupling chain and a pair of coupling sprockets. The coupling can be used over a wide range of applications. It is flexible and strong, and surpasses all others with its unique qualities. Tsubaki Overload Protection Torque Gard TGM Series are safety devices for the protection of machine equipment from overload. The Torq Gard TGM Series has many advantages compared to other safety devices such as pin type, friction type, ball type, roller type etc. Design Features Full Cam Complement The full compliment of cams provides the maximum number of load transmitting members per given diameter. The result is a higher torque capacity than other clutches. Cam Design Precision formed cams, made of special alloy steel assure extra long wear- and fatigue life. Tsubaki Echt Flex Couplings This non-backlash, lube-free coupling has high torsional stiffness, maximizing the benefit of servomotors. Based on finite element analysis, the disk is optimally designed to ensure reliable torque transmission, while absorbing misalignment smoothly. Tsubaki Sprockets Tsubaki sprockets are built from top-grade, heat-treated carbon steel to offer long wear life, resist abrasion and withstand heavy shock loads. For extra corrosion resistance and food grade applications, alloy and stainless steel sprockets are also available. You get longer service life and reliable performance, turn after turn, time after time. High Quality Components Outer- and inner races are made of high-quality alloy steel with high surface hardness and core toughness. The races are precision ground, providing excellent concentricity and surface finish to obtain cam rotation. 226 All models are RoHS compliant. Nationwide coverage, delivered locally same or next day – Tel: 0870 240 2100 Sprockets Chain Link Extractors 3/8" Simplex Sprockets - Pilot Bore Suitable for 3/8" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Quick and easy way to break a chain Can be used on all brands of chain Q Two sizes available for chains 3/8" to 5/8" and 3/4" to 1.1/4" BS/ANSI Q Q Price Each Order Code Product Code Size WX35187 CHAINEXTRNO1 3/8 - 5/8" WX35188 CHAINEXTRNO2 3/4 - 1.1/4" 1+ 5+ £50.38 £45.34 £117.44 £105.70 Part Code De Dp dm d1 A 31-17-1008:MECRO 55.3 51.83 45 1008 22 31-18-1008:MECRO 58.3 54.85 43 1008 22 31-19-1008:MECRO 61.3 57.87 45 1008 22 31-20-1008:MECRO 64.3 60.89 46 1008 22 31-21-1008:MECRO 68 63.91 46 1008 22 31-23-1210:MECRO 73.5 69.95 63 1210 25 31-24-1210:MECRO 77 72.97 62 1210 25 31-25-1210:MECRO 80 76.02 63 1210 25 31-27-1210:MECRO 86 82.02 63 1210 25 31-28-1210:MECRO 89 85.07 60 1210 25 31-30-1210:MECRO 94.7 91.12 63 1210 25 Chain Connecting Tool 3/8" Duplex Sprockets - Pilot Bore Q Q Suitable for 3/8" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A 3SR8:MECRO 28 24.89 15 8 20 3SR9:MECRO 31 27.85 18 8 20 3SR10:MECRO 34 30.82 20 8 20 3SR11:MECRO 37 33.8 22 8 25 Q 3SR12:MECRO 40 36.8 25 8 25 Q 3SR13:MECRO 43 39.79 28 10 25 3SR14:MECRO 46.3 42.8 31 10 25 3SR15:MECRO 49.3 45.81 34 10 25 3SR16:MECRO 52.3 48.82 37 10 28 3SR17:MECRO 55.3 51.83 40 10 28 3SR18:MECRO 58.3 54.85 43 10 28 3SR19:MECRO 61.3 57.87 45 10 28 3SR20:MECRO 64.3 60.89 46 10 28 3SR21:MECRO 68 63.91 48 12 28 Q 3SR22:MECRO 71 66.93 50 12 28 Q 3SR23:MECRO 73.5 69.95 52 12 28 Part Code De Dp dm d1 A 3SR24:MECRO 77 72.97 54 12 28 3DR12:MECRO 40 36.8 25 10 25 3SR25:MECRO 80 76 57 12 28 3DR13:MECRO 43 39.79 28 10 25 3SR26:MECRO 83 79.02 60 12 28 3DR14:MECRO 46.3 42.8 31 10 25 3SR30:MECRO 94.7 91.12 60 12 28 3DR15:MECRO 49.3 45.81 34 10 25 3SR32:MECRO 101.3 97.17 65 14 30 3DR16:MECRO 52.3 48.82 37 12 30 3DR17:MECRO 55.3 51.83 40 12 30 3DR18:MECRO 58.3 54.85 43 12 30 3DR19:MECRO 61.3 57.87 46 12 30 3DR20:MECRO 64.3 60.89 49 12 30 3DR21:MECRO 68 63.91 52 12 30 3DR22:MECRO 71 66.93 55 12 30 3DR23:MECRO 73.5 69.95 58 12 30 3DR25:MECRO 80 76 64 12 30 3DR30:MECRO 94.7 91.12 79 12 30 Tools designed to make roller chain connection quick and easy Can be used on all brands of chain Q Two sizes available for BS and ANSI chains from 0.375" pitch to 0.75" (CT35), and 1.00" pitch to 3.00" pitch (CT80) Price Each Order Code Product Code Chain Pitch WX38219 WX38220 CT35 1+ 0.375"-0.75" CT80 £119.28 1.00"-3.00" £269.39 5+ £107.35 £242.45 T-Max Chain Tensioners 3/8" Simplex Sprockets - Taper Bore • Automatically take up the slack with spring loaded T-Max Chain Tensioners. • Improve drive efficiency and extend component life with proper chain tension • A variety of design and size options suitable for a wide range of power transmission/motor applications. Product Code Type Chain Size Force (lbs) CT1111-L:FEND Linear-Large Arc UHMW Head 06B-1 5-30 CT1111:FEND Linear-Large Arc UHMW Head 06B-1 15-40 CT1112:FEND Linear-Large Arc UHMW Head 08B-1 15-40 CT2111:FEND Linear-Large Arc UHMW Head 10B-1 20-60 CT2109:FEND Linear-Large Arc UHMW Head 12B-1 20-60 CT3111:FEND Linear-Large Arc UHMW Head 16B-1 45-100 CT3112:FEND Linear-Large Arc UHMW Head 20B-1 45-100 CT3112-H:FEND Linear-Large Arc UHMW Head 20B-1 30-200 CT3102-H:FEND Linear-Large Arc UHMW Head 100-1 30-200 CT1113-L:FEND Linear-Large Arc UHMW Head 06B-2 5-30 CT1113:FEND Linear-Large Arc UHMW Head 06B-2 15-40 CT1114:FEND Linear-Large Arc UHMW Head 08B-2 15-40 CT3113:FEND Linear-Large Arc UHMW Head 16B-2 45-100 CT1103-L:FEND Linear-Large Arc UHMW Head 35-2 5-30 18 Chain Drives Chain Accessories Contact Brammer on 0870 240 2100 Suitable for 3/8" pitch roller chain Minimum bore allowing reworking for large bore and keyway Chain Drives 227 3/8" Duplex Sprockets - Taper Bore 1/2" Simplex Sprockets - Pilot Bore Suitable for 1/2" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Chain Drives 8 Q Q Suitable for 3/8" pitch roller chain Q Taper bore Q Last 4 digits indicates the taper bush that is required Q Suitable for 1/2" Ptich Roller Chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A 4SR10:MECRO 45.2 41.1 26 10 25 4SR11:MECRO 48.7 45.07 29 10 25 Part Code De Dp dm d1 A 4SR12:MECRO 53 49.07 33 10 28 32-17-1008:MECRO 55.3 51.83 41 1008 22 4SR13:MECRO 57.4 53.06 37 10 28 32-19-1008:MECRO 61.3 57.87 46 1008 22 4SR14:MECRO 61.8 57.07 41 10 28 32-21-1008:MECRO 68 63.91 49 1008 22 4SR15:MECRO 65.5 61.09 45 10 28 32-23-1210:MECRO 73.5 69.95 59 1210 25 4SR16:MECRO 69.5 65.1 50 12 28 32-24-1210:MECRO 77 72.97 61 1210 25 4SR17:MECRO 73.6 69.11 52 12 28 32-25-1210:MECRO 80 76.02 64 1210 25 4SR18:MECRO 77.8 73.14 56 12 28 32-27-1210:MECRO 86 82.02 70 1210 25 4SR19:MECRO 81.7 77.16 60 12 28 32-30-1210:MECRO 94.7 91.12 75 1210 75 4SR20:MECRO 85.8 81.19 64 12 28 4SR21:MECRO 89.7 85.22 68 12 28 4SR22:MECRO 93.8 89.24 70 12 28 4SR23:MECRO 98.2 93.27 70 14 28 4SR24:MECRO 101.8 97.29 70 14 28 4SR25:MECRO 105.8 101.33 70 14 28 4SR26:MECRO 110 105.36 70 16 30 4SR27:MECRO 114 109.4 70 16 30 4SR28:MECRO 118 113.42 70 16 30 4SR30:MECRO 126.1 121.5 80 16 30 4SR31:MECRO 130.2 125.54 90 16 30 4SR32:MECRO 134.3 129.56 90 16 30 4SR33:MECRO 138.4 133.6 90 16 30 4SR34:MECRO 142.6 137.64 90 16 30 3/8" Triplex Sprockets - Pilot Bore 4SR35:MECRO 4SR36:MECRO 146.7 151 141.68 145.72 90 90 1/2" Simplex Sprockets - Taper Bore Suitable for 3/8" pitch roller chain Q Minimum bore allowing reworking for large bore and keyway Q Part Code De Dp dm d1 A 3TR11:MECRO 37 33.8 22 10 35 3TR15:MECRO 49.3 45.81 34 12 35 3TR17:MECRO 55.3 51.83 40 12 35 3TR19:MECRO 61.3 57.87 46 12 35 3TR21:MECRO 68 63.91 52 14 40 3TR23:MECRO 73.5 69.95 58 14 40 3TR25:MECRO 80 76 64 14 40 228 16 16 30 35 Part Code De Dp dm d1 A 41-15-1008:MECRO 65.5 61.9 45 1008 22 41-16-1108:MECRO 69.5 65.1 50 1108 22 41-17-1210:MECRO 73.6 69.11 60 1210 25 41-18-1210:MECRO 77.8 73.14 60 1210 25 41-19-1210:MECRO 81.7 77.16 63 1210 25 41-20-1610:MECRO 85.8 81.19 71 1610 25 41-21-1610:MECRO 89.7 85.22 71 1610 25 41-22-1610:MECRO 93.8 89.24 70 1610 25 41-23-1610:MECRO 98.2 93.27 76 1610 25 41-24-1610:MECRO 101.8 97.29 70 1610 25 41-25-1610:MECRO 105.8 101.33 76 1610 25 41-26-1610:MECRO 110 105.36 70 1610 25 41-27-1610:MECRO 114 109.4 76 1610 25 41-28-2012:MECRO 118 1/2" Duplex Sprockets - Pilot Bore Q Q Suitable for 1/2" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A 4DR11:MECRO 48.7 45.07 32 12 35 4DR12:MECRO 53 49.07 35 12 35 4DR13:MECRO 57.4 53.06 38 12 35 4DR14:MECRO 61.8 57.07 42 12 35 4DR15:MECRO 65.5 61.07 46 12 35 4DR16:MECRO 69.5 65.1 50 14 35 4DR17:MECRO 73.6 69.11 54 14 35 4DR18:MECRO 77.8 73.14 58 14 35 4DR19:MECRO 81.7 77.16 62 14 35 4DR20:MECRO 85.8 81.19 66 14 35 4DR21:MECRO 89.7 85.22 70 16 40 4DR22:MECRO 93.8 89.24 70 16 40 4DR23:MECRO 98.2 93.27 70 16 40 4DR24:MECRO 101.8 97.29 75 16 40 4DR25:MECRO 105.8 101.33 80 16 40 4DR27:MECRO 114 109.4 85 16 40 4DR30:MECRO 126.1 121.5 100 16 40 90 Brammer Sales & Service Centres nationwide – Tel: 0870 240 2100 Part Code De Dp dm d1 A Part Code De Dp dm d1 A 4TR14:MECRO 61.8 57.07 42 14 50 5SR8:MECRO 47 41.8 25 10 25 4TR15:MECRO 65.5 61.09 46 14 50 5SR9:MECRO 52.6 46.42 30 10 25 4TR16:MECRO 69.5 65.1 50 16 50 5SR10:MECRO 57.5 51.37 35 10 25 4TR17:MECRO 73.6 69.11 54 16 50 5SR11:MECRO 63 56.34 37 12 30 4TR19:MECRO 81.7 77.16 62 16 50 5SR12:MECRO 68 61.34 42 12 30 4TR20:MECRO 85.8 81.19 66 16 50 5SR13:MECRO 73 66.32 47 12 30 4TR21:MECRO 89.7 85.22 70 16 55 5SR14:MECRO 78 71.34 52 12 30 4TR23:MECRO 98.2 93.27 70 16 50 5SR15:MECRO 83 76.36 57 12 30 4TR25:MECRO 105.8 101.33 80 16 55 5SR16:MECRO 88 81.37 60 12 30 4TR30:MECRO 126.1 121.5 100 20 55 5SR17:MECRO 93 86.39 60 12 30 5SR18:MECRO 98.3 91.42 70 14 30 5SR19:MECRO 103.3 96.45 70 14 30 5SR20:MECRO 108.4 101.49 75 14 30 5SR21:MECRO 113.4 106.52 75 16 30 5SR22:MECRO 118 111.55 80 16 30 5SR23:MECRO 123.5 116.58 80 16 30 5SR24:MECRO 128.3 121.62 80 16 30 5SR25:MECRO 134 126.66 80 16 30 5SR27:MECRO 144 134.75 85 20 35 5SR30:MECRO 158.8 151.87 90 20 35 1/2" Triplex Sprockets - Taper Bore Suitable for 1/2" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q 18 Chain Drives 1/2" Duplex Sprockets - Taper Bore 5/8" Simplex Sprockets - Taper Bore Q Part Code De Dp dm d1 A 42-15-1008:MECRO 65.5 61.9 46 1008 22 42-16-1108:MECRO 69.5 65.1 50 1108 22 42-17-1210:MECRO 73.6 69.11 56 1210 25 42-18-1210:MECRO 77.8 73.14 58 1210 25 42-19-1210:MECRO 81.7 77.16 62 1210 25 42-20-1610:MECRO 85.8 81.19 66 1610 25 42-21-1610:MECRO 89.7 85.22 70 1610 25 42-22-1610:MECRO 93.8 89.24 76 1610 25 42-23-1610:MECRO 98.2 93.27 79 1610 25 42-24-2012:MECRO 101.8 97.29 84 2012 32 42-25-2012:MECRO 105.8 101.33 87 2012 32 42-26-2012:MECRO 110 105.36 85 2012 32 42-27-2012:MECRO 114 109.4 87 2012 32 Part Code De Dp d1 A 42-30-2012:MECRO 126.1 121.5 87 2012 32 43-19-1210:MECRO 81.7 77.16 1210 34.9 43-21-1610:MECRO 89.7 85.22 1610 34.9 43-25-2012:MECRO 105.8 101.33 2012 34.9 43-30-2012:MECRO 126.1 121.5 2012 34.9 1/2" Triplex Sprockets - Pilot Bore Suitable for 1/2" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q dm 5/8" Simplex Sprockets - Pilot Bore Suitable for 5/8" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Q Q Suitable for 1/2" pitch roller chain Minimum bore allowing reworking for large bore and keyway Q Q Part Code De Dp dm d1 A 51-13-1008:MECRO 73 66.32 47 1008 22 51-14-1108:MECRO 78 71.34 52 1108 22 51-15-1210:MECRO 83 76.36 60 1210 25 51-16-1610:MECRO 88 81.37 70 1610 25 51-17-1610:MECRO 93 86.36 71 1610 25 51-18-1610:MECRO 98.3 91.42 75 1610 25 51-19-1610:MECRO 103.3 96.45 75 1610 25 51-20-1610:MECRO 108.4 101.49 75 1610 25 51-21-1610:MECRO 113.4 106.52 76 1610 25 51-22-1610:MECRO 118 111.55 76 1610 25 51-23-1610:MECRO 123.4 116.58 76 1610 25 51-24-2012:MECRO 128.3 121.62 90 2012 32 51-25-2012:MECRO 134 126.66 90 2012 32 51-26-2012:MECRO 139 131.7 85 2012 32 51-27-2012:MECRO 144 136.75 90 2012 32 51-28-2012:MECRO 148.7 141.78 90 2012 32 51-30-2012:MECRO 158.8 151.87 90 2012 32 Suitable for 5/8" pitch roller chain Minimum bore allowing reworking for large bore and keyway Contact Brammer on 0870 240 2100 Chain Drives 229 5/8" Duplex Sprockets - Pilot Bore Part Code De Dp d1 A 52-15-1210:MECRO 83 76.36 dm 1210 25.5 52-17-1610:MECRO 93 86.36 1610 25.5 52-18-1610:MECRO 98.3 91.42 1610 52-19-1610:MECRO 103.3 96.45 1610 25.3 52-20-1610:MECRO 108.4 101.49 1610 25.5 52-21-1610:MECRO 113.4 106.52 1610 25.5 52-23-1610:MECRO 123.4 116.58 1610 25.5 52-25-2012:MECRO 134 126.66 90 2012 32 52-27-2012:MECRO 144 136.75 90 2012 32 52-28-2012:MECRO 148.7 141.78 90 2012 32 52-30-2012:MECRO 158.8 151.87 90 2012 32 Suitable for 3/4" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Part Code De Dp dm d1 A 61-13-1210:MECRO 87.5 79.59 60 1210 25 61-14-1610:MECRO 93.6 85.61 71 1610 25 61-15-1610:MECRO 99.8 91.63 70 1610 25 61-16-1610:MECRO 105.5 97.65 75 1610 25 61-17-1610:MECRO 111.5 103.67 76 1610 25 61-18-2012:MECRO 118 109.71 90 2012 32 61-19-2012:MECRO 124.2 115.75 90 2012 32 61-20-2012:MECRO 129.7 121.78 90 2012 32 61-21-2517:MECRO 136 127.82 102 2517 45 61-22-2517:MECRO 141.8 133.86 102 2517 45 Suitable for 5/8" pitch roller chain Q Minimum bore allowing reworking for large bore and keyway 61-23-2517:MECRO 149 139.9 108 2517 45 61-24-2517:MECRO 153.9 145.94 108 2517 45 Part Code De Dp dm d1 A 61-25-2517:MECRO 160 152 108 2517 45 5DR12:MECRO 68 61.34 44 14 40 61-27-2517:MECRO 172.3 164 108 2517 45 5DR13:MECRO 73 66.32 49 14 40 61-30-2517:MECRO 190.5 182.25 108 2517 45 5DR14:MECRO 78 71.34 54 14 40 5DR15:MECRO 83 76.36 59 14 40 5DR16:MECRO 88 81.37 64 16 45 5DR17:MECRO 93 86.39 69 16 45 5DR18:MECRO 98.3 91.42 74 16 45 5DR19:MECRO 103.3 96.45 79 16 45 5DR20:MECRO 108.4 101.49 84 16 45 3/4" Simplex Sprockets - Pilot Bore Chain Drives 8 Q 3/4" Duplex Sprockets - Pilot Bore Q Q Suitable for 3/4" pitch roller chain Minimum bore allowing reworking for large bore and keyway 5DR21:MECRO 113.4 106.52 85 16 45 5DR23:MECRO 123.5 116.58 95 16 45 Part Code De Dp dm d1 A 5DR25:MECRO 134 126.66 105 16 45 6SR10:MECRO 69 61.64 42 12 30 5DR30:MECRO 158.8 151.87 120 20 45 6SR11:MECRO 75 67.61 46 14 35 6SR12:MECRO 81.5 73.61 52 14 35 6SR13:MECRO 87.5 79.59 58 14 35 6SR14:MECRO 93.6 85.61 64 14 35 6SR15:MECRO 99.8 91.63 70 14 35 6SR16:MECRO 105.5 97.65 75 16 35 6SR17:MECRO 111.5 103.67 80 16 35 6SR18:MECRO 118 109.71 80 16 35 6SR19:MECRO 124.2 115.75 80 16 35 6SR20:MECRO 129.7 121.78 80 16 35 6SR21:MECRO 136 127.82 90 20 40 6SR22:MECRO 141.8 133.86 90 20 40 6SR23:MECRO 149 139.9 90 20 40 6SR24:MECRO 153.9 145.94 90 20 40 6SR25:MECRO 160 152 90 20 40 6SR26:MECRO 165.9 158.04 95 20 40 Part Code De Dp dm d1 A 6SR27:MECRO 172.3 164.09 95 20 40 6DR11:MECRO 75 67.61 47 16 50 6SR30:MECRO 190.5 182.25 95 20 40 6DR13:MECRO 87.5 79.59 59 16 50 6DR14:MECRO 93.6 85.61 65 16 50 6DR15:MECRO 99.8 91.63 71 16 50 6DR16:MECRO 105.5 97.65 77 20 50 6DR17:MECRO 111.5 103.67 83 20 50 6DR19:MECRO 124.2 115.75 95 20 50 6DR20:MECRO 129.7 121.78 100 20 50 6DR21:MECRO 136 127.82 100 20 50 6DR23:MECRO 149 139.9 110 20 50 6DR24:MECRO 153.9 145.94 110 20 50 6DR25:MECRO 160 152 120 20 50 6DR26:MECRO 165.9 158.04 120 20 50 6DR30:MECRO 190.5 182.25 120 20 50 5/8" Duplex Sprockets - Taper Bore 3/4" Simplex Sprockets - Taper Bore Suitable for 5/8" pitch roller chain Q Taper bore Q Last 4 digits indicates the taper bush that is required Q 230 Q Q Suitable for 3/4" pitch roller chain Minimum bore allowing reworking for large bore and keyway We work harder to save you money and downtime – Tel: 0870 240 2100 3/4" Duplex Sprockets - Taper Bore 3/4" Triplex Sprockets - Taper Bore Part Code De Dp dm d1 A 8SR19:MECRO 165.2 154.33 100 20 45 8SR20:MECRO 173.2 162.38 100 20 45 8SR21:MECRO 181.2 170.43 110 20 50 8SR22:MECRO 189.3 178.48 110 20 50 8SR23:MECRO 197.5 186.53 110 20 50 8SR24:MECRO 205.5 194.59 110 20 50 8SR25:MECRO 213.5 202.66 110 20 50 8SR26:MECRO 221.6 21.72 120 20 50 8SR30:MECRO 254 243 120 20 50 1" Simplex Sprockets - Taper Bore Chain Drives 18 Suitable for 3/4" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Part Code De Dp 62-15-1610:MECRO 99.8 62-16-1610:MECRO 62-17-1610:MECRO dm d1 A 91.63 1610 30.3 105.5 97.65 1610 30.3 111.5 103.67 1610 30.3 62-19-2012:MECRO 124.2 115.75 90 2012 32 62-20-2517:MECRO 129.7 121.78 108 2517 45 62-21-2517:MECRO 136 127.82 108 2517 45 62-23-2517:MECRO 149 139.9 108 2517 45 62-24-2517:MECRO 153.9 145.94 108 2517 45 62-25-2517:MECRO 160 152 108 2517 45 62-27-2517:MECRO 172.3 164 108 2217 45 62-30-2517:MECRO 190.5 182.25 108 2517 45 Suitable for 3/4" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Part Code De Dp d1 A 63-15-1615:MECRO 99.8 91.63 dm 1615 49.8 63-17-2012:MECRO 111.5 103.67 1615 49.8 63-19-2012:MECRO 124.2 115.75 2012 49.8 63-21-2517:MECRO 136 127.82 2517 49.8 63-23-2517:MECRO 149 139.9 2517 49.8 63-25-2517:MECRO 160 152 2517 49.8 1" Simplex Sprockets - Pilot Bore Suitable for 1" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q 3/4" Triplex Sprockets - Pilot Bore Q Q Suitable for 3/4" pitch roller chain Minimum bore allowing reworking for large bore and keyway Q Q Suitable for 1" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A Part Code De Dp dm d1 A 6TR12:MECRO 81.5 73.61 53 20 70 8SR9:MECRO 85 74.27 50 16 35 6TR15:MECRO 99.8 91.63 71 20 70 8SR10:MECRO 93 82.19 55 16 35 6TR16:MECRO 105.5 97.65 77 20 70 8SR11:MECRO 101.5 90.14 61 16 40 6TR17:MECRO 111.5 103.67 83 20 70 8SR12:MECRO 109 98.14 69 16 40 6TR19:MECRO 124.2 115.75 95 20 70 8SR13:MECRO 117 106.12 78 16 40 6TR20:MECRO 129.7 121.78 100 20 70 8SR14:MECRO 125 114.15 84 16 40 6TR21:MECRO 136 127.82 100 20 70 8SR15:MECRO 133 122.17 92 16 40 6TR23:MECRO 149 139.9 110 20 70 8SR16:MECRO 141 130.2 100 20 45 6TR25:MECRO 160 152 120 20 70 8SR17:MECRO 149 138.22 100 20 45 8SR18:MECRO 157 146.28 100 20 45 Contact Brammer on 0870 240 2100 Part Code De Dp dm d1 A 81-13-1610:MECRO 117 106.12 73 1615 38 81-15-1610:MECRO 133 122.17 76 1615 38 81-16-2012:MECRO 141 130.2 90 2012 32 81-17-2012:MECRO 149 138.22 90 2012 32 81-18-2517:MECRO 157 146.28 108 2517 45 81-19-2517:MECRO 165.2 154.33 108 2517 45 81-20-2517:MECRO 173.2 162.38 108 2517 45 81-21-2517:MECRO 181.2 170.43 110 2517 45 81-23-2517:MECRO 197.5 186.53 110 2517 45 81-24-2517:MECRO 205.5 194.59 108 2517 45 81-25-2517:MECRO 213.5 202.66 110 2517 45 81-27-2517:MECRO 229.6 218.79 110 2517 45 81-28-2517:MECRO 237.7 226.85 108 2517 45 81-30-3020:MECRO 254 243 140 3020 51 For chain lubricants, see our Oils & Greases section Chain Drives 231 1" Duplex Sprockets - Pilot Bore 1" Triplex Sprockets - Pilot Bore 1 1/4" Simplex Sprockets - Pilot Bore Chain Drives 8 Q Q Suitable for 1" pitch roller chain Minimum bore allowing reworking for large bore and keyway Q Q Suitable for 1" pitch roller chain Minimum bore allowing reworking for large bore and keyway Q Q Suitable for 1 1/4" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A Part Code De Dp dm d1 A Part Code De Dp dm d1 A 8DR12:MECRO 109 98.14 72 20 70 8TR12:MECRO 109 98.14 72 25 100 10SR10:MECRO 117.9 102.74 70 20 40 8DR13:MECRO 117 106.12 80 20 70 8TR15:MECRO 133 122.17 96 25 100 10SR11:MECRO 127.8 112.68 77 20 45 8DR15:MECRO 133 122.17 96 20 70 8TR19:MECRO 165.2 154.33 128 25 100 10SR13:MECRO 147.8 132.65 98 20 45 8DR17:MECRO 149 138.22 112 20 70 8TR21:MECRO 181.2 170.43 130 25 100 10SR14:MECRO 157.8 142.68 108 20 45 8DR19:MECRO 165.2 154.33 128 20 70 10SR15:MECRO 167.9 152.720118 118 20 45 8DR20:MECRO 173.2 162.38 130 20 70 10SR16:MECRO 177.9 162.75 120 20 50 8DR21:MECRO 181.2 170.43 130 25 70 10SR17:MECRO 187.9 172.78 120 25 50 8DR23:MECRO 197.5 186.53 130 25 70 10SR18:MECRO 198 182.85 120 25 50 8DR25:MECRO 213.5 202.66 130 25 70 10SR19:MECRO 208.1 192.92 120 25 50 8DR26:MECRO 221.6 210.72 130 25 70 10SR20:MECRO 218.1 202.98 120 25 50 8DR32:MECRO 270 259.13 140 25 70 10SR23:MECRO 248.3 233.17 140 25 55 10SR25:MECRO 268.5 253.33 140 25 55 1" Triplex Sprockets - Taper Bore 1" Duplex Sprockets - Taper Bore 1 1/4" Duplex Sprockets - Pilot Bore Suitable for 1" pitch roller chain Taper bore Q Last 4 digits indicates the taper bush that is required Q Q Suitable for 1" pitch roller chain Q Taper bore Q Last 4 digits indicates the taper bush that is required Q Part Code De Dp 82-15-2012:MECRO 133 82-17-2517:MECRO 149 82-19-2517:MECRO d1 A 122.17 2012 47.7 138.22 2517 47.7 165.2 154.33 2517 47.7 82-21-3020:MECRO 181.2 170.43 140 3020 51 82-23-3020:MECRO 197.5 186.53 140 3020 51 82-25-3020:MECRO 213.5 202.66 140 3020 51 82-27-3020:MECRO 229.6 218.79 140 3020 51 82-30-3020:MECRO 254 243 140 3020 51 232 dm Part Code De Dp d1 A 83-17-2517:MECRO 149 138.22 dm 2517 79.6 83-19-3020:MECRO 165.2 154.33 3030 79.6 83-21-3020:MECRO 181.2 170.43 3030 79.6 83-23-3525:MECRO 197.5 186.53 159 3535 89 83-25-3525:MECRO 213.5 202.66 175 3535 89 Q Q Suitable for 1 1/4" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A 10DR17:MECRO 187.9 "172 78" 120 25 10DR19:MECRO 208.1 192.91 120 25 80 10DR23:MECRO 248.3 233.17 140 25 80 FREE 24/7 technical support – Tel: 0870 240 2100 80 Q Q 1 1/2" Duplex Sprockets - Pilot Bore Suitable for 1 1/4" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code Keyway Width (mm) Keyway Depth (mm) 1210-22:MECRO 6 2.8 1210-24:MECRO 8 3.3 1210-25:MECRO 8 3.3 1210-28:MECRO 8 3.3 1210-30:MECRO 8 3.3 1210-32:MECRO 10 3.3 1610-16:MECRO 5 2.3 1610-19:MECRO 6 2.8 1610-20:MECRO 6 2.8 1610-22:MECRO 6 2.8 1610-24:MECRO 8 3.3 1610-25:MECRO 8 3.3 1610-28:MECRO 8 3.3 1610-30:MECRO 8 3.3 1610-32:MECRO 10 3.3 1610-35:MECRO 10 3.3 1610-38:MECRO 10 3.3 1610-40:MECRO 12 3.3 1610-42:MECRO 12 2.2 2012-19:MECRO 6 2.8 2012-20:MECRO 6 2.8 2012-22:MECRO 6 2.8 2012-24:MECRO 8 3.3 2012-25:MECRO 8 3.3 2012-28:MECRO 8 3.3 2012-30:MECRO 8 3.3 2012-32:MECRO 10 3.3 2012-35:MECRO 10 3.3 Taper Bore Bushes 2012-38:MECRO 10 3.3 2012-40:MECRO 12 3.3 Taper Bore Bushes - Metric 2012-42:MECRO 12 3.3 2012-45:MECRO 14 3.8 2012-48:MECRO 14 3.8 2012-50:MECRO 14 3.8 2517-25:MECRO 8 3.3 2517-28:MECRO 8 3.3 2517-30:MECRO 8 3.3 2517-32:MECRO 10 3.3 2517-35:MECRO 10 3.3 2517-38:MECRO 10 3.3 2517-40:MECRO 12 3.3 2517-42:MECRO 12 3.3 2517-45:MECRO 14 3.8 2517-48:MECRO 14 3.8 2517-50:MECRO 14 3.8 2517-55:MECRO 16 4.3 2517-60:MECRO 18 4.4 3020-30:MECRO 8 3.3 3020-35:MECRO 10 3.3 3020-38:MECRO 10 3.3 3020-40:MECRO 12 3.3 3020-42:MECRO 12 3.3 3020-45:MECRO 14 3.8 3020-48:MECRO 14 3.8 3020-50:MECRO 14 3.8 3020-55:MECRO 16 4.3 3020-60:MECRO 18 4.4 3020-65:MECRO 18 4.4 3020-70:MECRO 20 4.9 3020-75:MECRO 20 4.9 3535-48:MECRO 14 3.8 3535-50:MECRO 14 3.8 3535-55:MECRO 16 4.3 3535-60:MECRO 18 4.4 3535-65:MECRO 18 4.4 3535-70:MECRO 20 4.9 3535-75:MECRO 20 4.9 3535-80:MECRO 22 5.4 Q Q Suitable for 1 1/2" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code De Dp dm d1 A Part Code De Dp dm d1 A 10TR17:MECRO 187.9 172.78 120 25 115 12DR15:MECRO 198.2 183.26 132 25 100 10TR19:MECRO 208.1 192.91 120 25 115 12DR19:MECRO 246.5 231.49 160 25 100 10TR21:MECRO 228.2 213.04 140 25 115 12DR25:MECRO 319 304 160 25 100 1 1/2" Simplex Sprockets - Pilot Bore Q Q Suitable for 1 1/2" pitch roller chain Minimum bore allowing reworking for large bore and keyway Part Code Keyway Width (mm) Keyway Depth (mm) 1008-12:MECRO 4 1.8 1008-14:MECRO 5 2.3 1008-16:MECRO 5 2.3 1008-19:MECRO 6 2.8 1008-20:MECRO 6 2.8 1008-24:MECRO 8 2 1008-25:MECRO 8 1.3 1108-10:MECRO 3 1.4 1108-11:MECRO 4 1.8 Part Code De Dp dm d1 A 1108-12:MECRO 4 1.8 12SR9:MECRO 126.4 111.4 70 20 45 1108-14:MECRO 5 2.3 12SR10:MECRO 138 123.29 80 20 45 1108-16:MECRO 5 2.3 12SR13:MECRO 174.2 159.18 114 25 50 1108-18:MECRO 6 2.8 12SR15:MECRO 198.2 183.26 132 25 50 1108-19:MECRO 6 2.8 12SR17:MECRO 222.3 207.34 136 25 55 1108-20:MECRO 6 2.8 12SR19:MECRO 246.5 231.49 136 25 55 1108-24:MECRO 8 3.3 12SR21:MECRO 270.6 255.65 150 25 60 1108-25:MECRO 8 3.3 12SR25:MECRO 319 304 150 25 60 1108-28:MECRO 8 2 12SR30:MECRO 379.5 364.5 150 30 60 1210-12:MECRO 4 1.8 1210-14:MECRO 5 2.3 1210-15:MECRO 5 2.3 1210-16:MECRO 5 2.3 1210-19:MECRO 6 2.8 1210-20:MECRO 6 2.8 Contact Brammer on 0870 240 2100 Chain Drives 18 Chain Drives 1 1/4" Triplex Sprockets - Pilot Bore 233 Part Code Keyway Width (mm) Keyway Depth (mm) Part Code Keyway Width (inch) Keyway Depth (inch) 3535-85:MECRO 22 5.4 3020-1-3/4:MECRO 0.437 0.156 3535-90:MECRO 25 5.4 3020-1-7/8:MECRO 0.5 0.156 4040-70:MECRO 20 4.9 3020-2:MECRO 0.5 0.156 4040-80:MECRO 22 5.4 3020-2-1/8:MECRO 0.625 0.218 4040-90:MECRO 25 5.4 3020-2-1/4:MECRO 0.625 0.218 4040-100:MECRO 28 6.4 3020-2-1/2:MECRO 0.625 0.218 4545-80:MECRO 22 5.4 3020-2-3/4:MECRO 0.75 0.25 4545-85:MECRO 22 5.4 3020-3:MECRO 0.75 0.218 4545-100:MECRO 28 6.4 3535-1-3/4:MECRO 0.437 0.156 5050-100:MECRO 28 6.4 3535-2:MECRO 0.5 0.156 5050-110:MECRO 28 6.4 3535-2-1/4:MECRO 0.625 0.218 5050-125:MECRO 32 7.4 3535-2-1/2:MECRO 0.625 0.218 3535-3:MECRO 0.75 0.25 4040-4:MECRO 1 0.25 8 Chain Drives Taper Bore Bushes - Imperial ETP Express Locking Bushes Trantorque Keyless Bush Locking bushes. Shafts 15-55mm ETP-EXPRESS locking bushes Q ETP locking bushes connect hubs, sprockets, pulleys and gears to shafts without keyways and collars Q Single radial fixing screw for ultra-fast fixing Q Automatic release without sticking Q Infinite axial & radial adjustment Q Shaft/hub machine tolerances h7/H7 Q High concentricity 0.03mm Q Temperature range -30 to +85°C Q Shafts up to 100mm available on request Q Min hub external diameter should be 1.5 x C if steel, 2.5 x C if aluminium Q Stainless steel & corrosion protected models on request Q Q Part Code Keyway Width (inch) Keyway Depth (inch) 1008-5/8:MECRO 0.187 0.093 1008-3/4:MECRO 0.187 0.093 1008-1:MECRO 0.25 0.125 1108-5/8:MECRO 0.187 0.093 1108-3/4:MECRO 0.187 0.093 1108-1:MECRO 0.25 0.125 1210-1/2:MECRO 0.125 0.062 1210-5/8:MECRO 0.187 0.093 1210-3/4:MECRO 0.187 0.093 1210-7/8:MECRO 0.25 0.125 1210-1:MECRO 0.25 0.125 1210-1-1/8:MECRO 0.312 0.125 1210-1-1/4:MECRO 0.312 0.125 1610-5/8:MECRO 0.187 0.093 TTQM0516 5 1610-3/4:MECRO 0.187 0.093 TTQM0616 1610-7/8:MECRO 0.25 0.125 1610-1:MECRO 0.25 1610-1-1/8:MECRO Product Code Bore mm Rated torque Nm Max radial A force kN C E Q ETP15-EXPRESS 15 46 0.5 46 18 39 Q ETP19-EXPRESS 19 85 1.0 50.5 23 42 ETP20-EXPRESS 20 110 1.0 51.5 24 44 ETP24-EXPRESS 24 190 1.4 57.5 29 47 ETP25-EXPRESS 25 230 1.5 58 30 49 ETP28-EXPRESS 28 280 1.8 63 34 52 ETP30-EXPRESS 30 380 2.0 64.5 36 54 32 440 2.2 68.5 39 56 Zero backlash - due to the shrink fit, longer life and reliability No keyway required - no weak spot in the shaft Q Single nut tightening - quick and easy installation Q Infinite postioning allowed - precise axial or radial postioning Q Highly concentric - self centering occures eliminating hub cocking during installation Trantorque Mini Component Length mm Overall length mm ETP32-EXPRESS ETP35-EXPRESS 35 640 2.5 73 42 59 16 19 10 ETP38-EXPRESS 38 890 2.8 84.5 46 72 6 16 19 10 ETP40-EXPRESS 40 1100 3.0 86.5 48 75 TTQM0720 7 20 22 11 ETP50-EXPRESS 50 1900 4.5 98.5 60 80 0.125 TTQM0820 8 20 22 11 ETP55-EXPRESS 55 2400 5.0 106 67 85 0.312 0.125 TTQM0920 9 20 22 11 1610-1-1/4:MECRO 0.312 0.125 TTQM1023 10 23 26 13 1610-1-3/8:MECRO 0.375 0.125 TTQM1123 11 23 26 13 1610-1-1/2:MECRO 0.375 0.125 TTQM1223 12 23 26 13 2012-3/4:MECRO 0.187 0.093 TTQM1426 14 26 29 16 2012-1:MECRO 0.25 0.125 TTQM1526 15 26 29 16 2012-1-1/8:MECRO 0.312 0.125 TTQM1626 16 26 29 16 2012-1-1/4:MECRO 0.312 0.125 2012-1-3/8:MECRO 0.375 0.125 2012-1-1/2:MECRO 0.375 0.125 2012-1-5/8:MECRO 0.437 0.156 Product Code Shaft mm OD mm 2012-1-3/4:MECRO 0.437 0.156 Component Length mm Overall length mm 2012-2:MECRO 0.5 0.125 TTQM1732 17 32 30 22 2517-1:MECRO 0.25 0.125 TTQM1832 18 32 30 22 2517-1-1/4:MECRO 0.312 0.125 TTQM1932 19 32 30 22 2517-1-1/2:MECRO 0.375 0.125 TTQM2035 20 35 33 24 2517-1-5/8:MECRO 0.437 0.156 TTQM2235 22 35 33 24 2517-1-3/4:MECRO 0.437 0.156 TTQM2438 24 38 35 25 2517-2:MECRO 0.5 0.156 TTQM2538 25 38 35 25 2517-2-1/4:MECRO 0.625 0.218 TTQM2845 28 45 41 29 2517-2-1/2:MECRO 0.625 0.187 TTQM3045 30 45 41 29 3020-1-1/4:MECRO 0.312 0.125 TTQM3250 32 50 44 30 3020-1-1/2:MECRO 0.375 0.125 TTQM3550 35 50 44 30 234 Product Code Shaft mm OD mm Trantorque Standard Can’t see it here, just call 0870 240 2100 Nationwide coverage, delivered locally same or next day – Tel: 0870 240 2100 ETP Classic Line Locking Bushes Chain Drives 18 ETP-CLASSIC locking bushes. Shafts 15-60mm ETP-CLASSIC locking bushes are a well known solution for fixing hubs, sprockets, pulleys and gears to shafts without the use of keyways or collars Q Easy fitting and removal with axial setting screws Q Low tightening torques Q No backlash or fretting Q Infinite axial & radial adjustment Q Radial concentricity 0.04mm Q Temperature range -30 to +85°C Q Shafts up to 100mm available on request Q Min hub external diameter should be 1.7 x C if steel, 2.7 x C if aluminium Q Stainless steel & corrosion protected models on request Q Q Product Code Bore mm Rated torque Nm Max radial A force kN C F ETP15 15 55 7.3 38 23 35 ETP19 19 100 10.6 45 28 42 ETP20 20 125 12.5 45 28 42 ETP24 24 200 16.7 49 34 45 ETP25 25 250 20.0 49 34 48 ETP28 28 300 21.4 55 39 50 ETP30 30 420 28 57 41 52 ETP32 32 420 26.3 60 43 57 ETP35 35 650 37.1 63 47 60 ETP38 38 750 39.5 65 50 64 ETP40 40 940 47 70 53 68 ETP42 42 940 44.5 70 55 70 ETP50 50 1900 76 83 65 82 ETP60 60 3400 113 95 77 96 Contact Brammer on 0870 240 2100 Chain Drives 235 Manufacture, process and supply plastic, insulation and rubber products to industry Excellence in Plastic Engineering for Industry PAR Group has over 30 years of experience serving clients in the UK, Europe and Worldwide. We have our own rubber moulding, converting, CNC machining, plastic fabrication, plastic forming, welding and stitching facilities. Additionally we also supply an extensive range of engineering plastics, insulation and rubber products. Having achieved ISO 9001 accreditation, PAR Group always strives for excellence in service and quality. With vast experience in rubber and plastics engineering, we are renowned for our ability to provide solutions to unusual and difficult applications. Engineering Plastic Materials We stock an extensive range of plastic sheet, rod and tube in various materials including machining, fabrication and specialist plastics. Our CNC saw facilities enable us to cut sheets up to 4000mm x 4000mm and up to a maximum thickness of 147mm. For rods, our automatic band saw provides a billeting service for up to 300mm diameter. Below are our most popular types of engineering plastics. $FHWDO&RSRO\PHU $FHWDO+RPRSRO\PHU $%6 $FU\OLF )RRG$SSURYHG +'3(/'3( 0HWDO'HWHFWDEOH 1\ORQ 3((. 3(7* 3RO\FDUERQDWH 3RO\HWK\OHQH 3RO\SURS\OHQH 37)( 39& 39') 8+0: 9HVSHO ® Extruded Wear Strips Wear strips are commonly used to prevent chain or belt movement and reduce vibration which can increase bearing and motor loads. We have the facilities to extrude Corrothene®8+0:ZHDUVWULSVWRDOPRVWDQ\SURILOH:HKDYHWRROV for a wide range of standard profiles along with in-house tool making facilities enabling us to extrude bespoke wear strips to your exact requirements. Nylon Casting 1\ORQFDVWLQJLVLGHDOIRUPDQXIDFWXULQJODUJHVKHHWVURGVRUWXEHVWKDWDUHQRWUHDGLO\DYDLODEOH7KLV manufacturing process is also suitable for producing the same plastic component required on a regular ® basis. At our IAC Plastics division we manufacture our own brand of CorromideFDVW1\ORQLQURGV sheets and tubes. We hold tooling for a range of standard sizes and also offer a custom Nylon casting service for specific customer requirements. We offer various Nylon grades and have ultra-sonic detection equipment enabling us to carry out inspections on all castings for any voids and porosity. www.par-group.co.uk Manufacture, process and supply plastic, insulation and rubber products to in ndustry Excellence in Plastic Engineering for Industry Plastic Machining PAR Group manufacture machined plastic components using highly advanced CNC machining technology. We have an extensive range of manufacturing facilities including CNC machining, cutting, routing, lathing, drilling and milling. We also have a team of KLJKO\ H[SHULHQFHG HQJLQHHUV DQG &$' technology, enabling us to precision engineer components to your exact requirements. Examples of our work: Machined Component Scraper Machined Wear Strips Scrolls / Wormfeeds Plastic Cover Plastic Cover Plastic Fabrication We have the facilities to fabricate, form, bend, weld, bond and polish a wide range of plastics. We commonly work with plastic PDWHULDOV VXFK DV 3RO\FDUERQDWH 3(7* Acrylic/Perspex®, 3RO\SURS\OHQH 39& DQG Polyethylene. We can flame polish the edges of certain plastic types for applications where aesthetics are an important factor. Examples of our work: Machine Guard Plastic Chute Contact Us For further details contact your nearest Brammer Sales & Service Centre on 0870 240 2100 www.par-group.co.uk