POSITIONING CHAIR
™
JUMBO
ASSEMBLY MANUAL
JUMBO – Assembly manual
CAUTION! Manufacturer takes responsibility for proper usage
of the device only when the product was purchased from
qualified Akces-Med employee or at specialized medical store.
Medical product first class according to the Regulation 93/42/EWG
of European Parliament and Council regarding medical products.
For this product the producer issued relevant declaration of conformity.
Producer's identification number in the Registration Department of Healing
Products, Medical Products and Biocide Products:
PL/CA01 04088/W
Akces-Med Sp. z o.o. Company introduced quality management system ISO 9001 and ISO
13485 regarding production, sales and service. The system is certified by Det Norske Veritas.
2
JUMBO – Assembly manual
LIST OF ELEMENTS:
a) right side
f)
b) left side
back bottom board
g) castor
h) backrest's arm
c) seat
i)
d) rib
e)
front bottom board
backrest
j) footrest
3
JUMBO – Assembly manual
k) abduction block
q) washer for tray
w) steel washer
l) tray
r) sleeve nut
x) knob
m) headrest
s) steel washer
y) screw M6x35
n) barrel nut L-16mm
t) cup square bolt
z) knob
o) screw M6x45
u) washer
aa) machine screw
p) cup washer
v) bush
bb) washer
cc) barrel nut L-13mm
4
JUMBO – Assembly manual
Stage I - Assembly of frame
1. Place right side (a) and seat's board (c) as it is presented in the picture below.
!
CAUTION! Stabilize elements e.g. put stabilizing elements thanks to which
elements cannot move lower- it prevents boards from damages. This rule
should be especially applied for points 1-11.
2. Insert barrel nuts (n) as it is shown in the picture below.
5
JUMBO – Assembly manual
!
CAUTION! Barrel nuts (n) should be inserted in a way that groove is situated
towards the bottom of seat.
3. Screw both elements (a) and (c) with the aid of screws (o) and cup washers (p) like it is
shown in the picture below. It is highly important to place firmly both elements (a) and (c)
either before or after they are tightened. This activity is useful because only then
elements do not move lower!
6
JUMBO – Assembly manual
4. Place left side (b) as it is presented in the pictures below.
5. Insert barrel nuts (n) as it is shown in the picture below. It should be done similarly as in
point 2.
7
JUMBO – Assembly manual
!
CAUTION! Barrel nuts (n) should be inserted in a way that groove is situated
towards the bottom of seat.
6. Screw elements with the aid of screws (o) and cup washers (p) like it is shown in the picture
below. It is highly important to place firmly elements either before or after they are
tightened. This activity is useful because only then elements do not move lower!
7. Place rib (d) as it is presented in the pictures below.
8
JUMBO – Assembly manual
8. Insert barrel nuts (n) from the left side of rib (d) as it is shown in the picture below.
.
!
CAUTION! Barrel nuts (n) should be inserted in a way that cut is placed
inwards to the chair
9
JUMBO – Assembly manual
9. Tighten rib (d) from the left side with the aid of screws (o) and cup washers (p) like it is
presented in the pictures below. CAUTION - hold rib firmly from both sides either before or
after it is tightened. This step is really important because it prevents rib from damages.
10
JUMBO – Assembly manual
10. Insert barrel nuts (n) from the right side of rib.
!
CAUTION! Barrel nuts (n) should be inserted in a way that groove is placed
inwards to the chair.
11
JUMBO – Assembly manual
11. Przykręcić żebro z prawej strony za pomocą śrub (o) z nakrętkami miseczkowymi (p), jak na
rysunkach poniżej. UWAGA – Przed przykręceniem żebra z obu stron cały czas
podtrzymywać je w celu zapobiegnięciu jego uszczerbania.
12
JUMBO – Assembly manual
12. Place front bottom board (e) as it is presented in the pictures below.
13. Insert barrel nuts (n) into Jumbo's side like it is shown in the picture below.
!
CAUTION! Barrel nuts (n) should be inserted in a way that groove is
placed inwards to the chair.
13
JUMBO – Assembly manual
14. Tighten first bottom board with the aid of screws (o) and cup washers (p) like it is shown in
the pictures below.
14
JUMBO – Assembly manual
!
CAUTION! Points 13 as well as 14 should be repeated for the second side.
15. Place back bottom board (f) like it is shown in the pictures below.
15
JUMBO – Assembly manual
16. Insert barrel nuts (n) like it is shown in the pictures below.
!
CAUTION! Barrel nuts (n) should be inserted in a way that groove is placed
inwards to the chair.
17. Tighten bottom board (f) with the aid of screws (o) and cup washers (p) like it is presented in
the pictures below.
16
JUMBO – Assembly manual
17
JUMBO – Assembly manual
!
CAUTION! Points 16 as well as 17 should be repeated for the second side of
back bottom board (f)
18. Place castors (g) and washers (s) as it is shown in the picture below.
18
JUMBO – Assembly manual
19. Tighten castors upwards like it is shown in the pictures below. Do it with the aid of sleeve
nuts (r).
19
JUMBO – Assembly manual
20. Place front castors (g) and washers (s) like it is presented in the pictures below.
20
JUMBO – Assembly manual
21. Tighten castors upwards like it is shown in the pictures below. Do it with the aid of sleeve
nuts (r).
22. The picture below shows how chair's frame
should be assembled.
Stage II - Assembly of backrest
1. Mount backrest's arm (h) from the left side as it is presented in the pictures below. Do it
with the aid of cup square bolt (t) and two washers (u) in two places (altogether 4).
21
JUMBO – Assembly manual
2. Tighten lightly bracket by means of knobs (x), steel washers (w) and washers (u).
22
JUMBO – Assembly manual
3. Mount backrest's arm (h) from the right side. It should be done similarly as for the left
side (point 1).
23
JUMBO – Assembly manual
4. Tighten lightly bracket (h). It should be done similarly as in point 2.
24
JUMBO – Assembly manual
5.
!
Place backrest (i) as it is presented in the picture below
CAUTION! Remember to adjust angles regarding turning of arms (h). It is
also important to adjust backrest in a way that holes in backrest (i) match
holes in arms (h).
25
JUMBO – Assembly manual
6. Insert barrel nuts (cc) as it is shown in the pictures below.
7. Tighten backrest with the aid of screws (y) and cup washers (p) from the front as it is
presented in the pictures below.
26
JUMBO – Assembly manual
!
CAUTION! Steps 6 and 7 should be repeated for the second side.
27
JUMBO – Assembly manual
8. The picture below shows how backrest should be assembled.
28
JUMBO – Assembly manual
Stage III - Assembly of footrest
1. Place footrest (j) as it is shown in the picture below.
2. Insert barrel nut (n) as it is presented in the picture below.
!
CAUTION! Barrel nuts should be inserted in a way that groove is placed
towards the bottom.
29
JUMBO – Assembly manual
3. Tighten footrest (j) from the left side with the aid of knob (z), steel washer (w) and washer
(u).
30
JUMBO – Assembly manual
4. Points 2 as well as 3 should be repeated for the right side. The picture below shows how
footrest should be tightened.
Stage IV - Assembly of abduction block
1.Place abduction block (k) like it is shown in the pictures below
31
JUMBO – Assembly manual
2. Tighten abduction block from the bottom as it is presented in the pictures below. Do it
with the aid of knob (x), steel washer (w) and washer (u).
32
JUMBO – Assembly manual
The picture below shows how abduction block should be mounted.
Stage V - Assembly of tray
1. Place tray (l) as it is shown in the picture below.
33
JUMBO – Assembly manual
2. Insert cup square bolt (t), washer (u) and bush (v) under the tray (l).
34
JUMBO – Assembly manual
3. Tighten tray with the aid of knob (x) and washer (q) like it is presented in the picture below.
35
JUMBO – Assembly manual
4. Point 2 and 3 should be repeated for the second side.
5. The picture below shows how tray should be mounted.
36
JUMBO – Assembly manual
Stage VI - Assembly of headrest
1. Place headrest (m) like it is shown in the pictures below.
2. Tighten headrest with the aid of machine screw (aa) and washers (bb)
37
JUMBO – Assembly manual
3. The picture below shows how headrest should be mounted.
38
JUMBO – Assembly manual
39
JUMBO – Assembly manual
MANUFACTURER OF ORTHOPEDIC DEVICES
Akces-MED. Sp. z o.o.
ul. Leszka Czarnego 3
35-615 Rzeszów
ph. (17) 864 04 70
www.akces-med.com
e-mail: akces-med@akces-med.com
Date of issue: 26.11.2014
The last update: 27.11.2014
AKCES-MED Ltd. reserve the right to introduce technical and trading changes
in the content of the instruction without warning.
40