shake
LOW DRESSER
assembly hardware
12 - wood
dowels
12 - bolts
32 - screws
mounting hardware
4 - plastic 4 - small
anchors
screws
Thank you for purchasing the Shake Low Dresser. This
page lists all the contents included in the box. Please take
the time to identify the hardware as well as the individual
components to this product. As you unpack and prepare
for assembly, place the contents on a carpeted or padded
area to protect them from damage.
Note: 2 people are recommended to safely assemble this product.
4 - large
screws
4 - mounting
brackets
2 - wall
straps
Missing hardware? Please call 800.606.6387 for replacements.
tools required
phillips head screwdriver
(We recommend the use of hand tools instead of power tools)
components
1 - top panel
1 - bottom panel
1 - partition
1 - back panel
2 - side panels
(1 left, 1 right)
8 - drawer sides
(4 left, 4 right)
4 - drawer bottoms
2 - left drawer
fronts
Made in Vietnam - r03
2 - right drawer
fronts
4 - drawer backs
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 1 of 6
shake
LOW DRESSER
top
panel
1
bottom
panel
Insert 6 wood dowels into top panel as shown.
2
right side
panel
Insert 6 wood dowels into bottom panel.
Note: Do not over
tighten the bolts
partiton
left side
panel
3
With assistance of another adult, fit dowels of top panel
into corresponding holes of left/right side panels and
partition. Attach each panel with 2 bolts. Secure, but do
not over tighten, bolts with a phillips head screwdriver.
Made in Vietnam - r03
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 2 of 6
shake
LOW DRESSER
back
panel
4
Insert back panel into corresponding grooves of
assembly.
bottom
panel
5
Fit dowels of bottom panel into corresponding
holes of assembly and attach with 6 bolts.
Made in Vietnam - r03
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 3 of 6
shake
LOW DRESSER
left drawer
side
left drawer
front
6
drawer
bottom
Attach left drawer side to left drawer front with 2
screws. Secure, but do not over tighten, screws
with a screwdriver.
7
drawer
back
8
Attach drawer back to left drawer side with 2
screws.
Made in Vietnam - r03
Fit drawer bottom into corresponding grooves of
drawer assembly.
right drawer
side
9
Attach right drawer side to drawer assembly with
4 screws.
Repeat steps 6-9 for remaining left and right
drawers.
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 4 of 6
shake
LOW DRESSER
NOTE: Make sure to keep
drawer level to not damage
glides during assembly
NOTE: Make sure glides are pulled
out of the case and ball bearings are
at the front of the extended glides.
To prevent damage to glides, keep drawer
assembly level during installation.
left drawer
assembly
10
Fit drawer glides of each drawer into
corresponding drawer glides of case
assembly. Make sure drawer glides are
securely engaged.
Assembly is now complete.
right drawer
assembly
cleaning and care
Clean surfaces with a dry or damp soft cloth. Do not
use abrasive cleaners.
Made in Vietnam - r03
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 5 of 6
shake
LOW DRESSER
C
D
A
E
optional wall mounting instructions
For added safety and stability, it is recommended that the wall mounting hardware be installed. For safe
mounting, it is essential to use wall anchors appropriate to your wall type (i.e. plaster, drywall, concrete, etc.).
Mount to wood studs whenever possible.
NOTE: If you are unsure about your wall type or what mounting method you should use, consult a
qualified professional or your local hardware store.
A. Attach 2 brackets to the top of the assembled unit with 2 small screws per bracket.
B. With the assistance of another adult, place the unit in desired location against the wall. Mark the
location of the hole in the bracket on the wall. Move the unit out of the workspace.
C. Drill holes slightly smaller in diameter than the anchors. Insert 1 plastic anchor into each hole until
they are flush to the wall.
D. Insert 2 large screws through each bracket and plastic anchor. Secure, but do not over tighten
with a phillips head screwdriver.
E. Place the unit back into position against the wall and thread the wall strap through both brackets
and pull until tight.
Wall mounting assembly is now complete.
Made in Vietnam - r03
Customer Service 800.606.6252 | Latest instructions available at www.cb2.com
Page 6 of 6