Installation Manual (English)

advertisement

User's Guide

Ergotron LX

Wall Mount

USA 1-800-888-8458

Europe +31 20 312.29.39

1

1x

A

1x

B

2

2x

3

1x

1/8"

1x

1x

2.5mm

1x

4x

C

75-100mm

D

4x

4x

#8-32

4x

M4 x 10mm

1x

M4 x 10mm

3/32"

1x

10-24 x 1/2"

1x

For optimum ergonomic viewing, set top of monitor screen

1″ below eye height of operator.

4mm

888-45-041-00 rev.D • 11/05

1 of 8

1

Determine Ergonomic Mounting Height

(for wall mounted applications)

Monitor

Size

15"

16"

18.1"

20"

21"

22"

Mounting Heights

Screen Aspect Ratios

Sitting

4 x 3

Standing

34.8"

(883 mm)

50.8"

(1289 mm)

Sitting

35.6"

16 x 9

(904 mm)

Standing

51.6"

(1310 mm)

34.5"

(875 mm)

33.8"

(859 mm)

33.3"

(845 mm)

33"

(837 mm)

32.7"

(829 mm)

50.5"

(1281 mm)

49.8"

(1265 mm)

49.3"

(1251 mm)

49"

(1243 mm)

48.7"

(1236 mm)

35.3"

(897 mm)

34.8"

(884 mm)

34.4"

(872 mm)

34.1"

(866mm)

33.9"

(860 mm)

51.3"

(1304 mm)

50.8"

(1291 mm)

50.45"

(1279 mm)

50.1"

(1273 mm)

49.9"

(1266 mm)

These mounting heights assume your monitor mounting holes are located in the center, relative to the monitor screen. If your monitor's mounting holes are located off center (vertically), you can adjust your mounting height accordingly.

ie. (Back of Monitor)

#

,

Subtract 1" (25 mm) from the Mounting Height.

h

MM

#

, h

MM

Add 1" (25 mm) from the Mounting Height.

!RMINFULLUPPOSITION

!RMINFULLUPPOSITION

For confi gurations without extension, add

3.5" (89 mm) to the mounting height from the table above.

-OUNTING

(EIGHT

-OUNTING

(EIGHT v

MM

888-45-041-00 rev.D • 11/05

2 of 8

2

4x

10-24 x 1/2"

4x

10-24 x 1/2"

4x

10-24 x 1/2"

4x

10-24 x 1/2"

4x

10-24 x 1/2"

4x

10-24 x 5/8" when attaching to Pole Clamps, use 10-24 x 5/8" screws, Do NOT use 10-24 x 1/2" screws

4x

10-24 x 1/2"

4x

10-24 x 1/2"

1/8"

!

WARNING

Because surfaces vary widely and the ultimate mounting method is out of Ergotron’s control, it is imperative that you consult with appropriate engineering, architectural or construction professional to ensure that your Ergotron mounting solution is mounted properly to handle applied loads.

1.125"

(28.6mm)

4.1"

(104mm)

888-45-041-00 rev.D • 11/05

3 of 8

3

!

If your monitor uses a screw size other than M4 x 10mm, DO NOT use the M4 x 10mm screws or knob provided as they could result in damage to the monitor.

4x

#8-32

3/32"

a

4x

M4 x 10 mm M4 x 10 mm

b

4x

M4 x 10 mm M4 x 10 mm

P

4O

P

4O

888-45-041-00 rev.D • 11/05

4 of 8

4

• With Extension • Without Extension

5

Leave enough slack in cable to pivot arm and monitor

888-45-041-00 rev.D • 11/05

5 of 8

6

Range of Motion

The Ergotron LX Monitor Arm is designed to adjust quickly and easily according to your needs - refer to following steps for adjustment and page 8 for Ergonomic

Ground Rules.

Lift - Up & Down

±50˚

Tilt - Back & Forth

75˚

Pan/Arm Swing

- Side-to-side

up to 360˚ up to 360˚ up to 180˚

Rotate - P/L

(Portrait/Landscape)

90˚

13"

(330 mm)

7

Lift Motion

Move monitor up and down through entire range of motion. If it does not stay in place at any point it will need adjustment - see below. Adjust so upward and downward moving forces are equal. Once this is achieved turn adjustment screw 2-4 turns clockwise to give slight upward bias to lift system.

±50˚

Adjust Lift

To Increase Lifting Force: Turn screw clockwise.

To Decrease Lifting Force: Turn screw counterclockwise.

13"

(330 mm)

4mm

!

CAUTION

DO NOT overtighten fasteners.

Overtightening may cause damage to your equipment.

888-45-041-00 rev.D • 11/05

6 of 8

8

Tilt Motion

75˚

Tilt monitor back and forth through entire pivot range of motion. If it does not stay in place or movement in one direction is stiff, pivot needs adjustment - see below. Adjust until monitor stays in place and tilting forces, up or down, are equal.

Adjust Tilt

To Increase Tilt Lifting Force: Turn screw clockwise.

To Decrease Tilt Lifting Force: Turn screw counterclockwise.

!

CAUTION

Never remove this adjustment screw! Removing adjustment screw will cause damage to the arm and possible damage to equipment.

9 up to 360˚

Arm Swing

Swing arms from side-to-side at both pivot points through entire range of motion. If it does not stay in place or movement in one direction is stiff, tension needs adjustment - see below.

Adjust until arms stay in place and tension, side-to-side, is equal.

up to 360˚

Adjust Arm Swing

2.5mm

To Increase Tension: Turn screw clockwise.

To Decrease Tension: Turn screw counterclockwise.

888-45-041-00 rev.D • 11/05

7 of 8

?

Troubleshooting

Lift - Up & Down Tilt - Back & Forth

75˚ up to 360˚

Arm Swing

- Side-to-side

up to 360˚

±50˚

13"

(330 mm)

Symptom

Monitor lifts up and down too easily or with diffi culty.

Probable Cause

Lifting force needs adjustment.

Solution

7

Lift Motion

USA 1-800-888-8458

Europe +31 20 312.29.39

6

Monitor exceeds weight capacity*.

Monitor tilts back and forth too easily or with diffi culty.

Tilt lifting force needs adjustment.

8

Tilt Motion

7

Arm swings from side-to-side too easily or with diffi culty.

Side-to-side tension needs adustment.

9

Arm Swing

7

*Weight Capacity

:

5 - 20 lbs. (2.27 - 9.1 kg).

Warranty

%RGOTRONWARRANTSTHATITSPRODUCTSWILLREMAINFREEOFDEFECTSINMATERIAL

ANDWORKMANSHIPFOR YEARS

%XCLUSIVE 2EMEDY )F ANY %RGOTRON EQUIPMENT IS OR BECOMES DEFECTIVE IN MATERIAL OR

WORKMANSHIPDURINGTHEWARRANTYPERIOD0URCHASERMUSTRETURNTHEITEMTO%RGOTRON

WITHAWRITTENEXPLANATIONOFTHEDEFECT%RGOTRONWILLPROMPTLYREPAIRORREPLACETHE

ITEM AND SHIP IT TO 0URCHASER WITHOUT CHARGE TO 0URCHASER 0ERFORMANCE OF REPAIR OR

REPLACEMENTDOESNOTRENEWOREXTENDTHEWARRANTYPERIOD

4()32%-%$9)34(%%8#,53)6%2%-%$9&/2"2%!#(/&7!22!.49!34/4(%%15)0

-%.4 EXCEPT IN RESPECT TO PERSONAL INJURY 0URCHASER SHALL GIVE %RGOTRON IMMEDIATE

WRITTENNOTICEOFANYPERSONALINJURYRESULTINGFROMUSEOF%RGOTRONEQUIPMENT

%XCLUSIONSAND,IMITATIONS%RGOTRONDISCLAIMSLIABILITYFORINJURIESORLOSSESCAUSEDBYOR

ASSOCIATEDWITHINSTALLATIONORUSEOFITSEQUIPMENTINANYMANNEROTHERTHANINSTRICT

CONFORMANCEWITHTHEINSTRUCTIONSHEETSTECHNICALBULLETINSORPRODUCTLITERATUREORBY

EQUIPMENTTHATHASBEENALTEREDDAMAGEDORMISUSED

0URCHASERHASNOTRELIEDUPONAND%RGOTRONDISCLAIMSANYANDALLWARRANTIESOTHERTHAN

THEEXPRESSEDWARRANTYSTATEDABOVESUBJECTTOTHEEXCLUSIONSANDLIMITATIONSPROVIDED

HEREIN%RGOTRONDISCLAIMSALLOTHERWARRANTIESEXPRESSEDORIMPLIEDINCLUDINGBUTNOT

LIMITEDTOTHEWARRANTIESOFMERCHANTABILITYANDFITNESSFORAPARTICULARPURPOSE

%RGOTRON FURTHER DISCLAIMS LIABILITY TO PURCHASER AND ALL OTHERS FOR ALL CONSEQUENTIAL

INCIDENTALANDSPECIALDAMAGESCAUSEDBYORINCONNECTIONWITHTHEPRODUCTSTHEIRUSE

ORMISUSEANDTHEIRPERFORMANCEORNONPERFORMANCE

© 2005 Ergotron, Inc. All rights reserved.

Patents Pending and Patented U.S. & Foreign. Ergotron is a registered trademark of Ergotron, Inc. Reproduction of this material in whole or part for any purpose other than that authorized by Ergotron, Inc. is prohibited.

8 of 8

888-45-041-00 rev.D • 11/05

Download