RF full touch wall panel HX-SWB

advertisement
RF full touch wall panel
HX-SWB
Smart Wireless Series
HX-SWB is a series of full touch wall panel which
designed for LED lamps. Adopt RF wireless remote
control technology, more fixable and convenient for
installation, its compatibility with a wide variety of LED
arrays and numerous control options will enable it to be
widely used in LED intelligent lighting. Will form constant
current control system for LED interior lamps when
configured with HX-SWA series, such as LED
DOWNLIGHT, LED CEILING LIGHT, LED PANEL LIGHT,
etc. Will form constant voltage control system for
corresponding
product
when
configured
with
HX-SZ100/HX-SZ600 series, such as LED STRIP, LED
MODULES, etc.
Features










Groundbreaking use of the wireless RF remote control technology,do not need to make changes to the original
wiring, the installation is more flexible and convenient.
The work voltage is: AC90-265V, do not need to configure the adapter.
Intuitive panel allowing intelligent lighting with brilliant simplicity.
RF signal sender, RF frequency: 433.92MHz。
Unique encoding avoids signal interference and maintains system’s stability.
Transmission Distance:up to 30m,no need line-of-sight.
Sleep-wakeup design, for energy conservation.
Highly accurate of the devices’ communication because of the Independence between ON and OFF.
The dimension according to the international 86-type standards.
1 year limited warranty.
HX-SWB series item group
Working appearance
Dimming control panel
ELECPOLO SL
CT control panel
RGB control panel
4 groups control panel
E-mail:elecpolo@elecpolo.com
www.elecpolo.com
RF full touch wall panel
Technical specification










Working voltage:AC90-265V(50/60Hz)
RF signal frequency:433.92MHz
Transmission distance:up to 30m(the deviation depend on the environment)
Working power:<2W
Standby power:<0.2W
Ambient temperature:0-45℃
Dimension:86*86*40mm
Packing dimension: L89*W40*H89mm
N.W.:130g
G.W: 140g
Case dimension
Packing and Dimension: L89*W40*H89mm
ELECPOLO SL
E-mail:elecpolo@elecpolo.com
www.elecpolo.com
RF full touch wall panel
Connection diagram
Installation Method
1) Opening: Gently pry gaps in touch panel with a screwdriver, and remove the panel slowly, as shown below:
2)Unplug the connector, connect the power cord, and fix the base part in the 86*86 installation box ( user need to
ELECPOLO SL
E-mail:elecpolo@elecpolo.com
www.elecpolo.com
RF full touch wall panel
prepare the installation box by themselves) on the wall with screws.
3)Reconnect the two parts of panel, and cover the face part on the base part to complete the
installation.
Product function introduction
1、Dimming control panel
2、CT control panel
ELECPOLO SL
E-mail:elecpolo@elecpolo.com
www.elecpolo.com
RF full touch wall panel
3、RGB control panel
4、 groups control panel
4-in-1 control panel. Support 4 groups control signal in max.

This series RF full touch faceplate will sleep down in more than 20 seconds no used to save the energy. In this
ELECPOLO SL
E-mail:elecpolo@elecpolo.com
www.elecpolo.com
RF full touch wall panel

case, the touch ring will be no reaction, please touch any one of the other function buttons to wake up the
remote control firstly.
RF signal light Flicker means the RF signal have been sent out with correct operation every time, and die out in
free time. Power light stay on to show the normal working status.
Important: As RF signal sender, set up the LED Touch faceplate to a RF led driver (RF receiver)
before use.
1. Press and hold the “Mode” key before the “RF LED Driver” powering on, the RF signal light lights red.
2. Power up the “RF LED Driver”, and the LEDs will output 50% brightness (Tip: if the output does not output 50%
brightness, indicating that the code learning is not successful, need to repeat the step 1).
3. Press the “ON” key, then the LEDs will be 25% brightness.
4. Press the “Mode” key again, then the LEDs will be 5% brightness.
5. Press the “ON” key again,then the LEDs will be 100% brightness,and indicating the successful code learning. If not,
repeat from step 1.
“Mode” (power on the receiver)-“ON”-“Mode”-“ON”
Compatible Controls
HX-SWC series as a RF wireless remote control should be configured with RF driver/controller (RF receiver) to form
a complete control system. The details listed in the chart below:
Type
CV
HX-SWC
Receiver
RC No.
Re No.
Control range
Application
HX-SWB-RGB
HX-SZ100-TOUCH
1
1
0-100%
CV RGB
HX-SWB-DIM
HX-SZ100-DIM
1
1
0-100%
CV dimming
HX-SWB-CT
HX-SZ100-CT
1
1
0-100%
CV CT
HX-SWB-RGB
HX-SZ600-TOUCH
1
1
0-100%
CV RGB
HX-SWB-DIM
HX-SZ600-DIM
1
1
0-100%
CV dimming
HX-SWB-CT
HX-SZ600-CT
1
1
0-100%
CV CT
HX-SWB-4GC
HX-SZ100-DIM
1
1-4
0-100%
CV Dimming
RC: remote control; Re: receiver; CC: constant current; CV: constant voltage; CT: WWH+CWH.
Contact Hoion for more information.
ELECPOLO SL
E-mail:elecpolo@elecpolo.com
www.elecpolo.com
Download