HF1000 - Woodway Engineering

advertisement
ENGINEERING
TEL: 024 7684 1750 FAX: 024 7662 1796
Website: http://www.woodwayengineering.co.uk
A
B
C
D
DATA SHEET
HEADLAMP FLASHER
Model – HF1000
E
SPECIFICATION:
SIZE: 133mm x 63.5mm x 31mm
FIXING HOLE CENTRES: 124mm x 38mm
FIXING HOLE DIA: 5mm
INPUT VOLTAGE: 12Vdc.
OUTPUT FLASHRATE:
CONNECTION: SCREW TERMINALS
OPERATION:
The unit is designed to work on vehicles with either –ve chassis or +ve chassis and has
alternating and simultaneous flash outputs. The unit has an inhibit facility which, when
connected, disables the unit when the vehicle lights are in use e.g. at night.
MOUNTING:
The unit is not potted and is not waterproof it should, therefore, be mounted in a cool and dry
location. It is recommended that it is not mounted in the engine compartment of a vehicle nor in
a location where it may be subject to road spray.
WIRING:
All wiring should be sized as indicated on the wiring diagrams. The use of wire of a smaller csa
than that shown is not recommended and will invalidate the warranty. All wires connecting to
the terminal block should be terminated with bootlace ferrules or crimp terminals of the correct
size for the wire used. It is the responsibility of the customer to ensure that the correct
terminals and crimp tools are used.
All switches, fuses etc are to be supplied by the customer.
8S:\ENGINEERING\Product Installation\DATASHTS\HF1000 Issue C.DOC
WIRING FOR SIMULTANEOUS AND ALTERNATING FLASH +VE SWITCHING HEADLIGHTS
A
B
1 2 3 4
C
D
E
V C S AO 1 2
0.5
UNIT INHIBIT +ve SUPPLY
FROM VEHICLE LIGHTS
0.5
1.0
N/S HEADLIGHT
MAIN BEAM
VEHICLE N/S HEADLIGHT
MAIN BEAM SUPPLY (+VE)
-VE CHASSIS
0.5
0.5
S
Off
A
0.5
-VE CHASSIS
SWITCH
S = SIMULTANEOUS
A = ALTERNATING
FUSE
BATTERY +Ve
1.0
O/S HEADLIGHT
MAIN BEAM
3A
2.0
VEHICLE O/S HEADLIGHT
MAIN BEAM SUPPLY (+VE)
FUSE
BATTERY +Ve
20A
-VE CHASSIS
WIRING FOR SIMULTANEOUS FLASH ONLY +VE SWITCHING HEADLIGHTS
A
B
1 2 3 4
C
D
E
V C S AO 1 2
0.5
UNIT INHIBIT +ve SUPPLY
FROM VEHICLE LIGHTS
0.5
1.0
N/S HEADLIGHT
MAIN BEAM
-VE CHASSIS
VEHICLE HEADLIGHT
MAIN BEAM SUPPLY (+VE)
0.5
0.5
-VE CHASSIS
S
Off
ON-OFF SWITCH
FUSE
1.0
BATTERY +Ve
3A
O/S HEADLIGHT
MAIN BEAM
VEHICLE HEADLIGHT
MAIN BEAM SUPPLY (+VE)
2.0
FUSE
BATTERY +Ve
20A
-VE CHASSIS
WIRING NOTES:
For alternating only operation fit a single pole on-off switch and wire to terminal D/A and +ve.
For simultaneous only operation fit a single pole on-off switch and wire to terminals D/S and +ve.
For both alternating and simultaneous operation fit an ‘on’-‘off’-‘on’ switch and wire one ‘on’
position to terminal D/A, the other ‘on’ position to terminal D/S and the pole to +ve.
UNIT INHIBIT:
It is recommended that this feature is enabled to prevent the operation of the unit when the
vehicle lights are switched on.
To enable the unit inhibit connect a +ve supply, when the side-lights are operated, to terminal E1.
S:\ENGINEERING\Product Installation\DATASHTS\HF1000 Issue C.DOC
WIRING FOR SIMULTANEOUS AND ALTERNATING FLASH -VE SWITCHING HEADLIGHTS
A
B
1 2 3 4
C
D
E
V C S AO 1 2
0.5
UNIT INHIBIT +ve SUPPLY
FROM VEHICLE LIGHTS
0.5
1.0
N/S HEADLIGHT
MAIN BEAM
VEHICLE N/S HEADLIGHT
MAIN BEAM –VE SWITCHED
0.5
-VE CHASSIS
0.5
+VE
S
Off
A
0.5
SWITCH
S = SIMULTANEOUS
A = ALTERNATING
FUSE
BATTERY +Ve
1.0
O/S HEADLIGHT
MAIN BEAM
3A
VEHICLE O/S HEADLIGHT
MAIN BEAM –VE SWITCHED
2.0
BATTERY -Ve
+VE
WIRING FOR SIMULTANEOUS FLASH ONLY -VE SWITCHING HEADLIGHTS
A
B
1 2 3 4
C
D
E
V C S AO 1 2
0.5
UNIT INHIBIT +ve SUPPLY
FROM VEHICLE LIGHTS
0.5
1.0
N/S HEADLIGHT
MAIN BEAM
-VE CHASSIS
VEHICLE HEADLIGHT
MAIN BEAM -VE SWITCHED
0.5
+VE
0.5
S
Off
ON-OFF SWITCH
FUSE
1.0
BATTERY +Ve
3A
O/S HEADLIGHT
MAIN BEAM
VEHICLE HEADLIGHT
MAIN BEAM -VE SWITCHED
2.0
BATTERY -Ve
+VE
WIRING NOTES:
For alternating only operation fit a single pole on-off switch and wire to terminal D/A and +ve.
For simultaneous only operation fit a single pole on-off switch and wire to terminals D/S and +ve.
For both alternating and simultaneous operation fit an ‘on’-‘off’-‘on’ switch and wire one ‘on’
position to terminal D/A, the other ‘on’ position to terminal D/S and the pole to +ve.
UNIT INHIBIT:
It is recommended that this feature is enabled to prevent the operation of the unit when the
vehicle lights are switched on.
To enable the unit inhibit connect a +ve supply, when the side-lights are operated, to terminal E1.
S:\ENGINEERING\Product Installation\DATASHTS\HF1000 Issue C.DOC
Download