4760 SERIES
END-TO-END CEILING MOUNT
INSTALLATION INSTRUCTIONS
Installation should be performed by a qualified
electrician in accordance with the National Electrical Code
and relevant local codes.
1. Install anchor bolts (A)
(redhead studs, molly
bolts or other suitable
anchors-anchors by
others) into ceiling per
“Mounting Details” (see
page 2). Make sure that
mounting bolts project
between 1/2” - 2” from
mounting surface.
2. Remove lens (B) from
fixture. Remove reflector/
ballast assembly (C) from
fixture by rotating two 1/4
fasteners (D) on reflector
assembly.
3. Remove the knockout
plug (K) closest to the
electrical service (L) on
the fixture housing (F).
4. Mount fixture housing (F)
over anchor bolts (A)
pulling the electrical
conductors from service
into the fixture housing
(F). Tighten the bolts
ensuring that the ceiling
gasket (M) is properly
seated against the
ceiling.
5. Place the end-to-end
gasket (E) on the end of
the fixture housing (F),
aligning the gasket (E) to
the through holes. Lift
and align the adjacent
fixture housing (F) to be
installed against the
end-to-end gasket (E) and over the anchor bolts (A). Insert three 1/4-20 screws (G) through the ends of the adjacent fixture
housings, threading the three 1/4-20 nuts (H) on to the screws (G). Thread anchor bolt nuts onto anchor bolts (A). Tighten the
three 1/4-20 end nuts (H). Tighten the anchor bolt nuts, ensuring the ceiling gasket (M) is properly seated against the ceiling
surface. Repeat step #5 until all fixture housings (F) are mounted to the ceiling.
6. Connect the electrical service conductors to the housing wiring harness (N) and to the through branch circuit conductors
(O) - per the “Close Up Detail - Through Branch Wiring” (see page 2).
7. Connect the housing wiring harness (N) to the reflector/ballast assembly wiring harness (P).
8. Re-install the reflector/ballast assembly (C) to the fixture housing (F) via the 1/4 turn fasteners (D).
9. Install the lamps (Q) into the fixture. Make sure the proper lamp is installed and that the labelled end of the lamp is positioned into the correct end of the reflector/ballast assembly (C).
10. Re-install the lens (B).
11. Repeat steps 6-10 until all fixtures are completed.
INSTALLATION DIAGRAM
©2007 Hydrel
Rev. 3/28/07
INS-4760 ceiling ETE_Rev0
NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT
NOTICE. Any dimension on this sheet is to be assumed as a reference
dimension: "Used for information purposes only. It does not govern
manufacturing or inspection requirements." (ANSI Y14.5-1973)
20660 Nordhoff St., Suite B
Chatsworth, CA 91311
Phone: 866.533.9901
Fax: 866.533.5291
www.hydrel.com
4760 SERIES
END-TO-END CEILING MOUNT
INSTALLATION INSTRUCTIONS
6.1. Loosen wireway cover plate
screw (R), remove wireway cover
(S) from fixture housing (F).
Installation should be performed by a qualified
electrician in accordance with the National Electrical Code
and relevant local codes.
CLOSE UP DETAIL THROUGH BRANCH WIRING - STEP 6
6.2. Feed through branch circuit
conductors (O) through opening
to adjacent fixture housing (F).
6.3. Connect through branch circuit
conductors (O) to housing wiring
harness (N) with wire nuts (T).
6.4. Insert connected wiring assembly
into back portion of fixture
housing (F) and replace wireway
cover plate (S), tightening screw
(R).
6.5. Continue with general installation
per Step #7.
MOUNTING DETAIL - CEILING MOUNT
©2007 Hydrel
Rev. 3/28/07
INS-4760 ceiling ETE_Rev0
NOTE: HYDREL RESERVES THE RIGHT TO MODIFY SPECIFICATION WITHOUT
NOTICE. Any dimension on this sheet is to be assumed as a reference
dimension: "Used for information purposes only. It does not govern
manufacturing or inspection requirements." (ANSI Y14.5-1973)
20660 Nordhoff St., Suite B
Chatsworth, CA 91311
Phone: 866.533.9901
Fax: 866.533.5291
www.hydrel.com