TDK-Lambda PML12030A007V C261-01-01C ABSOLUTE MAXIMUM RATINGS Stresses in excess of the absolute maximum ratings can cause permanent damage to the device. ITEMS Symbol Max Unit Min Continuous Input Voltage Vin 14 Vdc -0.3 o Operating Case Temperature Tc 115 -40 C o Operating Ambient Temperature Ta -40 85 C o Storage Temperature Tstg -55 125 C Notes & Conditions See Derating Curve ELECTRICAL SPECIFICATIONS Unless otherwise indicated, specifications apply over all Input Voltage, Resistive Load, and Temperature conditions. ITEMS Symbol Min Typ Max Unit Notes & Conditions V Operating Input Voltage Vin 12 14 8 Vin=Vin,min, Vo=Vo,set, Io=Io,max A Maximum Input Current Iin,max ----8.6 Output Voltage Set-point Vo,set -1.5 --+1.5 % Vo,set Vin=Vin,nom, Io=Io,max,Ta=25oC, TRIM resistor tolerance = +/-0.5% or less Output Voltage Tolerance Vo,set Line Regulation Load Regulation Output Voltage Adjustment Range Remote Sense Range Output Ripple and Noise Voltage External Load Capacitance Co,max Output Current Io Output Current Limit Threshold Io,lim Efficiency Vo=0.7V h h Vo=1.2V h Vo=2V Switching Frequency fsw Turn-On Input Voltage Turn-Off Input Voltage On/Off Control Remote On Von/off Remote Off Von/off Turn-On Delay Time Tdelay -3 --- +3 ----0.7 ----47 0 105 --------------4 --- ----------300 ----83 88 91 210 7.2 4.9 ----5 10 10 2 0.5 50 1000 30 --------------0.8 ----- % Vo,set Over all operating input voltage, resistive load, and temperature conditions to end of life, TRIM resistor tolerance = +/-0.5% or less mV Vin=Vin,min to Vin,max mV Io=Io,min to Io,max V V mVp-p Co=100mFx3+0.1mF, Refer to C261-01-02_ mF A See Derating Curve % Io,max Vo=0.9xVo,set, Ta=25oC % Vin=12V, Io=Io,max, Vo=Vo,set, Ta=25oC % % kHz Fixed V V V V ms From application of input voltage until Vo=0.1xVo,set. Vin=Vin,nom, Vo=Vo,set, Io=Io,max, Ta=25oC Tdelay 5 --- --- ms From ON/OFF enabled until Vo=0.1xVo,set. Vin=Vin,nom, Vo=Vo,set, Io=Io,max, Ta=25oC Output Voltage Rise Time --- Trise 1.5 --- ms From Vo=0.1xVo,set until Vo=0.9xVo,set. Io=Io,max, Ta=25oC ----- Tc --140 Possible 112.5 87.5 5 6.4 --------- Vpg 3 --- % Vo,set Co=100mFx3+0.1mF --------- % Vo,set o C Refer to Instruction Manual for Parallel operation. % Vo,set V g Approved by UL60950-1, CSA60950-1, EN60950-1 100 Refer to Instruction Manual 80 Io (%) Output Voltage Overshoot Over Temperature Protection Parallel Operation PGOOD Over Voltage Threshold Under Voltage Threshold Internal Pull up Voltage Weight Safety Derating Curve for Tc Location. 60 40 20 0 -60 -40 -20 0 20 40 Tc (oC) 60 80 100 115 120 TDK-Lambda PML12030A007V C261-01-02B 1.BASIC CONNECTION *Read instruction manual carefully, before using the power supply unit. ==NOTES== *1. Use an external fuse (Normal blow type) for each unit. *2. Put input capacitor. C1 : Ceramic capacitor 25V, 22uF x 7 in parallel *3. Pull up Resistor. R1 : Resistor 4.7kW *4. Output Voltage Adjustment Resistor.(Refer to Instruction Manual.) *5. Put output capacitor. C2 : Ceramic capacitor 50V, 0.1uF *6. Put output capacitor. C3 : Ceramic capacitor 6.3V, 100uF x 3 in parallel 2.OPTION TABLE PML12030A007V-XXX Option code 000 001 (Standard) XXX: Option code ON/OFF Positive Logic Short code L300 Negative Logic L301 Short code is indicated on name plate.