t
0459 263 101 GB 060523 Valid for serial no. 620--xxx--xxxx

1 DIRECTIVE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
2 SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
3 INTRODUCTION
3.1 Equipment
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4 TECHNICAL DATA . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1 Placing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.2 Rating plate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.3 Mains power supply . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6 OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1 Connections and control devices . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2 Connection of welding and return cable . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.3 Control panel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.4 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5 Overheating protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.6 MMA welding
6.7 TIG welding
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.8 Remote control unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7 MAINTENANCE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1 Cleaning the dust filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
8 FAULT TRACING
8.1 Fault codes
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9 ORDERING SPARE PARTS
DIAGRAM
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ORDERING NUMBER . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SPARE PARTS LIST
ACCESSORIES
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5
6
6
6
6
7
7
7
7
9
10
9
9
10
11
11
11
12
3
3
5
5
12
14
16
17
18
Rights reserved to alter specifications without notice.
TOCe
-- 2 --

DECLARATION OF CONFORMITY
ESAB AB, Welding Equipment, SE--695 81 Laxå, Sweden, gives its unreserved guarantee that welding power source Arc 150i from serial number 620 complies with standard IEC/EN 60974--1, in accordance with the requirements of directive (73/23/EEC) and addendum (93/68/EEC) and with standard IEC/EN 60974--10 in accordance with the requirements of directive (89/336/EEC) and addendum (93/68/EEC).
--------------------------------------------------------------------------------------------------------------------------------------
Laxå 2006--05--22
Kent Eimbrodt
Global Director Equipment and Automation
ESAB AB
695 81 LAXÅ
SWEDEN Tel: + 46 584 81000 Fax: + 46 584 411924
Users of ESAB welding equipment have the ultimate responsibility for ensuring that anyone who works on or near the equipment observes all the relevant safety precautions. Safety precautions must meet the requirements that apply to this type of welding equipment. The following recommendations should be observed in addition to the standard regulations that apply to the workplace.
All work must be carried out by trained personnel well--acquainted with the operation of the welding equipment. Incorrect operation of the equipment may lead to hazardous situations which can result in injury to the operator and damage to the equipment.
1.
Anyone who uses the welding equipment must be familiar with:
S its operation
S location of emergency stops
S its function
S relevant safety precautions
S welding
2.
3.
The operator must ensure that:
S no unauthorized person is stationed within the working area of the equipment when it is started up.
S no--one is unprotected when the arc is struck
The workplace must:
S be suitable for the purpose
S be free from drafts
4.
5.
Personal safety equipment
S
Always wear recommended personal safety equipment, such as safety glasses, flame--proof clothing, safety gloves.
S
Do not wear loose--fitting items, such as scarves, bracelets, rings, etc., which could become trapped or cause burns.
General precautions
S Make sure the return cable is connected securely.
S
Work on high voltage equipment may only be carried out by a qualified electrician.
S Appropriate fire extinquishing equipment must be clearly marked and close at hand.
bh26d1e
-- 3 --

ARC WELDING AND CUTTING CAN BE INJURIOUS TO YOURSELF AND OTHERS. TAKE PRECAU-
TIONS WHEN WELDING. ASK FOR YOUR EMPLOYER’S SAFETY PRACTICES WHICH SHOULD BE
BASED ON MANUFACTURERS’ HAZARD DATA.
ELECTRIC SHOCK -- Can kill
S Install and earth the welding unit in accordance with applicable standards.
S
S
S
Do not touch live electrical parts or electrodes with bare skin, wet gloves or wet clothing.
Insulate yourself from earth and the workpiece.
Ensure your working stance is safe.
FUMES AND GASES -- Can be dangerous to health
S
Keep your head out of the fumes.
S
Use ventilation, extraction at the arc, or both, to take fumes and gases away from your breathing zone and the general area.
ARC RAYS -- Can injure eyes and burn skin.
S
Protect your eyes and body. Use the correct welding screen and filter lens and wear protective
S clothing.
Protect bystanders with suitable screens or curtains.
FIRE HAZARD
S
Sparks (spatter) can cause fire. Make sure therefore that there are no inflammable materials nearby.
NOISE -- Excessive noise can damage hearing
S
Protect your ears. Use earmuffs or other hearing protection.
S
Warn bystanders of the risk.
MALFUNCTION -- Call for expert assistance in the event of malfunction.
READ AND UNDERSTAND THE INSTRUCTION MANUAL BEFORE INSTALLING OR OPERATING.
PROTECT YOURSELF AND OTHERS!
ESAB can provide you with all necessary welding protection and accessories.
WARNING!
Read and understand the instruction manual before installing or operating.
WARNING!
Do not use the power source for thawing frozen pipes.
This product is solely intended for arc welding.
Do not dispose of electrical equipment together with normal waste!
In observance of European Directive 2002/96/EC on Waste Electrical and Electronic
Equipment and its implementation in accordance with national law, electrical equipment that has reached the end of its life must be collected separately and returned to an environmentally compatible recycling facility. As the owner of the equipment, you should get information on approved collection systems from our local representative.
By applying this European Directive you will improve the environment and human health!
-- 4 -bh26d1e

The Arc 150i is a welding current power source intended for use with coated electrodes (MMA welding) and TIG welding.
The Arc 150i is supplied with 3 m of mains cable and an instruction manual.
ESAB’s accessories for the product can be found on page 18 .
Arc 150i
Mains voltage
Fuse (delayed--action)
Primary current I max
Primary current I eff
Voltage/current range (DC)
Maximum permissible load at
25% duty cycle
35% duty cycle
60% duty cycle
100% duty cycle
Power factor at maximum current
Efficiency at maximum current
Open--circuit voltage
Operating temperature
Constant A--weighed sound pressure
Dimensions, l x b x h
Weight
Enclosure class
Application class
230 V, 1
16 A
36 A
21 A
150 A / 26 V
140 A / 26 V
110 A / 25 V
90 A / 24 V
0,62
77%
71--78 V
--10 ˚ C -- +40
< 70 db
IP 23C
˚ C
394 x 267 x 274 mm
9 kg
μ 50/60 Hz
4 A /20 V -- 150 A /26 V
Duty cycle
The duty cycle refers to the time as a percentage of a ten--minute period that you can weld at a certain load without overloading.
Enclosure class
The IP code indicates the enclosure class, i. e. the degree of protection against penetration by solid objects or water. Equipment marked IP23 is designed for indoor and outdoor use.
Application class
The symbol electrical hazard.
indicates that the power source is designed for use in areas with increased
-- 5 -bh26d1e

The installation must be executed by a professional.
WARNING!
This product is intended for industrial use. In a domestic environment this product may cause radio interference. It is the user’s responsibility to take adequate precautions.
Note!
Connect the power source to the electricity mains with a network impedance of 0.210 ohm or lower. If the network impedance is higher, there is a risk of flicker in the illuminators.
Place the power source so that its cooling air inlets and outlets are not obstructed.
The rating plate is located on the underside of the power source.
Make sure that the welding power source is connected to the correct supply voltage and that it is protected by the correct fuse rating. The standards for the country in question must be complied with as regards the mains cable area. A protective earth connection must be made in accordance with regulations.
5.3.1
Recommended fuse sizes and minimum cable areas
Arc 150 i
Mains voltage
Mains frequency
Fuse (delayed--action)
100A 20% duty cycle
120A 35% duty cycle
150A 35% duty cycle
Mains cable, area
Welding cable, area
230 V ¦ 10 %, 1--phase
50--60 Hz
10 A
16 A
20 A*)
3 x 2.5 mm 2
16 mm 2
*) Note! The installed plug is approved for max. 16A.
North American version: The mains cable is approved for maximun 18 A.
Note!
The cable area and fuse rating above comply with Swedish regulations. Use the welding power source in accordance with the relevant national regulations.
-- 6 -bh26d1e

1 Main power supply switch, 0 / 1
2 Mains cable
3 Connection for return cable (--)
4 Connection for remote control
5 Welding cable connector (+)
6 Control panel (see 6.2)
3 and 5 are used for welding current supply and return cable connection during MMA welding
The welding power source has two terminals, one plus and one minus pole, for the connection of the welding and the return cable. Connect the welding cable to the pole indicated on the package of the electrode to be used.
Connect the return cable to the other terminal. Fit the earth clamp of the return cable to the work--piece and make sure there is good contact between the work--piece and the return cable terminal on the welding power source.
Welding process parameters are controlled via the control panel.
-- 7 -bh26d1e

6.3.1
Functional description
7
8
9
5
6
3
4
Pos
1
2
Symbol/Function
Knob for setting data
Arc Force
Hot Start
TIG welding “Live TIG--start”
MMA welding with coated electrodes
Pushbutton indicating welding current (A) and/or arc voltage (V)
Connection of remote control unit
Indicating lamp (green), mains power supply
Indicating lamp (yellow) for overheating
6.3.2
Panel function symbols
Set values
--
0 -- 99%
0 -- 99%
--
--
--
--
--
--
MMA Amp/Volt Fjärrdon
TIG
6.3.3
Hidden functions
Hot Start Arc Force
A number of setting options for welding data, such as drop welding and ArcPlus t
, are obtained by pressing Arc Force for at least 1 second.
and Hot Start simultaneously
The function is selected using the setting knob, and the welding method is selected by pressing the ArcForce or HotStart button.
The following welding data setting options for MMA can be found under the letters:
D = setting Drop welding
F = setting regulator ArcPlus t
Return by pressing ArcForce second.
and HotStart simultaneously for 1
-- 8 -bh26d1e

Settings
Arc Force
Drop welding
Regulator ArcPlus t
Hot Start
Setting range
0 -- 99%
I / 0
I / 0
0 -- 99%
--
--
In steps of:
1 %
1 %
0
1
Default value
5 %
0 %
The welding power source has a thermal overload trip which operates if the temperature becomes too high, interrupting the welding current and lighting a yellow indicating lamp on the front of the power source. The thermal overload trip resets automatically when the temperature has fallen.
The Arc 150i gives direct current, and you can weld most metals to alloy and non-alloy steel, stainless steel and cast iron. The Arc 150i allows you to weld most coated electrodes from ∅ 1.6 to ∅ 3.25.
MMA welding may also be referred to as welding with coated electrodes. Striking the arc melts the electrode, and its coating forms protective slag.
If, when striking the arc, the tip of the electrode is pressed against the metal, it immediately melts and sticks to the metal, rendering continued welding impossible.
Therefore, the arc has to be struck in the same way that you would light a match.
Quickly strike the electrode against the metal, then raise it so as to give an appropriate arc length (approx. 2 mm). If the arc is too long, it will crackle and spit before finally going out completely.
If you are working on a welding bench, check before attempting to strike the arc that residual waste metal, pieces of electrode or other objects do not insulate the part to be welded.
Once the arc has been struck, move the electrode from left to right. The electrode must be at an angle of 60 ˚ to the metal in relation to the direction of welding.
cmha2p11
When you want to weld wide beads, or when you want the weld to be so thick that you have to weld in a number of layers, however, you have to use lateral movements.
cmha2p10
Setting regulator -- ArcPlus t
The Arc 150i is supplied with ArcPlus t
, a new type of control that, during MMA welding, produces a more intensive, more concentrated and calmer arc. It recovers more quickly after a drop short--circuit, which reduces the risk of the electrode becoming stuck.
Drop welding (MMA)
Drop welding can be used when welding with stainless electrodes.
This technique involves alternately striking and extinguishing the arc in order to achieve better control of the supply of heat. The electrode needs only to be raised slightly to extinguish the arc.
-- 9 -bh26d1e

Hot Start
Hot start increases the weld current for an adjustable time at the start of welding, thus reducing the risk of poor fusion at the beginning of the joint.
Arc Force
The arc force is important in determining how the current changes in response to a change in the arc length. A lower value gives a calmer arc with less spatter.
Current
A higher current produces a wider weld pool, with better penetration into the workpiece.
The current set value can be changed irrespective of which menu is displayed. This value is displayed in the main menu only.
TIG welding melts the metal of the workpiece, using an arc struck from a tungsten electrode, which does not itself melt. The weld pool and the electrode are protected by shielding gas.
TIG welding is particularly useful when high quality standards are required and when welding thin sheet. Arc 150i also has very good TIG welding characteristics.
Before using the Arc 150i for TIG welding it must be equipped with:
S a TIG torch and gas valve
S a cylinder of argon
S an argon regulator
S tungsten electrodes
S suitable filter metal, if necessary.
“Live Tig--start“
The Live Tig--start“ function strikes the arc when the electrode is brought into contact with the workpiece and then lifted away from it.
The remote control unit has to be connected to the remote control unit socket on the power source.
If the remote control unit is not to be used, this function is removed from the panel.
-- 10 -bh26d1e

Regular maintenance is important for safe, reliable operation.
Note!
All guarantee undertakings from the supplier cease to apply if the customer himself attempts any work in the product during the guarantee period in order to rectify any faults.
S
Remove the fan grille: see sketch.
S
Release the dust filter
S
Blow the filter clean with compressed air (reduced pressure).
S
Ensure that the filter with the finest mesh is placed towards the grille.
S
Replace the fan grille with the dust filter.
Try these recommended checks and inspections before sending for an authorised service technician.
No arc.
Type of fault
The thermal overload trips operate frequently.
The thermal overload trip operates frequently.
Poor welding performance.
Action
S
Check that the mains power supply switch is turned on.
S Check that the welding current supply and return cables are correctly connected.
S
Check that the correct current value is set.
S Check to see whether the MCB has tripped.
S
Check whether the thermal overload trips have operated
(indicated by the orange lamp on the front panel).
S Check the main power supply fuses.
S
Check to see whether the dust filter is clogged.
S Make sure that you are not exceeding the rated data for the power source (i.e. that the unit is not being overloaded).
S
Check that the welding current supply and return cables are correctly connected.
S Check that the correct current value is set.
S
Check that the correct electrodes are being used.
S
Check the main power supply fuses.
-- 11 -bh26d1e

The Arc 150i comes with built--in fault monitoring. If a fault occurs, a code is shown in the display.
If any of these fault codes is displayed permanently or recurs often, the machine should be sent to an authorised ESAB service workshop for repair.
Fau lt
Description
E1 Internal RAM fault
Resetting Action
E2 External RAM fault
E3 EPROM fault
E4 Fault in RAM with battery backup
E5 Memory error, variable value outside limits
E6 Low battery voltage Reset by pressing a button
Restart the machine.
If the fault persists, contact a service workshop
Restart the machine.
If the fault persists, contact a service workshop
Restart the machine.
If the fault persists, contact a service workshop
Restart the machine.
If the fault persists, contact a service workshop
Restart the machine.
If the fault persists, contact a service workshop
If the fault persists, contact a service workshop
E10 + 20V fault
(18.5 – 21.5 V)
E11 --15 V fault
(--13.0 -- --16.0)
E13 High temperature
E14 Current servo fault
E99 Bridging fault
Automatic reset once fault has disappeared
Automatic reset once fault has disappeared
Automatic reset once fault has disappeared
Automatic reset once fault has disappeared Also reset by pressing a button
The digital control card is bridged in a non--defined combination.
Switch off the machine. If the fault persists, contact the service workshop.
Arc150i is designed and tested in accordance with the international and European standards IEC/EN 60974--1 and EN 60974--10. It is the obligation of the service unit which has carried out the service or repair work to make sure that the product still conforms to the said standard.
Repair and electrical work should be performed by an authorized ESAB serviceman.
Use only ESAB original spare and wear parts.
Spare parts may be ordered through your nearest ESAB dealer, see the last page of this publication.
-- 12 -bh26d1e

p
-- 13 --

Diagram
CaddyArc150
-- 14 --

CaddyArc150
-- 15 --

Arc 150i
Ordering number
Ordering no.
Denomination Type
0459 199 880 Welding Power source Caddy t Arc 150i, A34 for 230 V mains voltage
0459 199 886 Welding Power source Caddy t Arc 150i, A34 for 230 V mains voltage,
North American version
0459 263 990 Spare parts list Caddy t
Arc 150i bh26o
-- 16 --
Edition 060523

Arc 150i
Spare parts list
Item Qty Ordering no.
101 1 0459 277 001 Filter
Denomination bh26s
-- 17 -Edition 060523

Arc 150i
Accessories bh26a
MMA welding and return cable kit . . . . . . .
(”crocodile” type holder)
MMA welding and return cable kit . . . . . . . .
(”screwe” type holder)
Remote control MMA 1 (10 m cable) . . . . . . .
MMA and TIG: current
0349 501 078
0349 501 079
0349 501 024
Foot control FS002 . . . . . . . . . . . . . . . . . . . . . .
MMA and TIG current
0349 090 886
Remote control unit AT1 . . . . . . . . . . . . . . . . .
MMA and TIG: current
0459 491 896
Remote control unit AT1 CF . . . . . . . . . . . . .
MMA and TIG: rough and fine setting of current.
0459 491 897
Remote cable 12 pole -- 8 pole
5 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
25 m . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
0459 552 880
0459 552 881
0459 552 882
0459 552 883
Shoulderstrap . . . . . . . . . . . . . . . . . . . . . . . . . . 0459 367 880
-- 18 -R0459 263 /E060523/P18

p
-- 19 --

Europe
AUSTRIA
ESAB Ges.m.b.H
Vienna--Liesing
Tel: +43 1 888 25 11
Fax: +43 1 888 25 11 85
BELGIUM
S.A. ESAB N.V.
Brussels
Tel: +32 2 745 11 00
Fax: +32 2 745 11 28
THE CZECH REPUBLIC
ESAB VAMBERK s.r.o.
Prague
Tel: +420 2 819 40 885
Fax: +420 2 819 40 120
DENMARK
Aktieselskabet ESAB
Herlev
Tel: +45 36 30 01 11
Fax: +45 36 30 40 03
FINLAND
ESAB Oy
Helsinki
Tel: +358 9 547 761
Fax: +358 9 547 77 71
FRANCE
ESAB France S.A.
Cergy Pontoise
Tel: +33 1 30 75 55 00
Fax: +33 1 30 75 55 24
GERMANY
ESAB GmbH
Solingen
Tel: +49 212 298 0
Fax: +49 212 298 218
GREAT BRITAIN
ESAB Group (UK) Ltd
Waltham Cross
Tel: +44 1992 76 85 15
Fax: +44 1992 71 58 03
ESAB Automation Ltd
Andover
Tel: +44 1264 33 22 33
Fax: +44 1264 33 20 74
HUNGARY
ESAB Kft
Budapest
Tel: +36 1 20 44 182
Fax: +36 1 20 44 186
ITALY
ESAB Saldatura S.p.A.
Mesero (Mi)
Tel: +39 02 97 96 81
Fax: +39 02 97 28 91 81
THE NETHERLANDS
ESAB Nederland B.V.
Utrecht
Tel: +31 30 2485 377
Fax: +31 30 2485 260
NORWAY
AS ESAB
Larvik
Tel: +47 33 12 10 00
Fax: +47 33 11 52 03
POLAND
ESAB Sp.zo.o.
Katowice
Tel: +48 32 351 11 00
Fax: +48 32 351 11 20
PORTUGAL
ESAB Lda
Lisbon
Tel: +351 8 310 960
Fax: +351 1 859 1277
SLOVAKIA
ESAB Slovakia s.r.o.
Bratislava
Tel: +421 7 44 88 24 26
Fax: +421 7 44 88 87 41
SPAIN
ESAB Ibérica S.A.
Alcalá de Henares (MADRID)
Tel: +34 91 878 3600
Fax: +34 91 802 3461
SWEDEN
ESAB Sverige AB
Gothenburg
Tel: +46 31 50 95 00
Fax: +46 31 50 92 22
ESAB international AB
Gothenburg
Tel: +46 31 50 90 00
Fax: +46 31 50 93 60
SWITZERLAND
ESAB AG
Dietikon
Tel: +41 1 741 25 25
Fax: +41 1 740 30 55
North and South America
ARGENTINA
CONARCO
Buenos Aires
Tel: +54 11 4 753 4039
Fax: +54 11 4 753 6313
BRAZIL
ESAB S.A.
Contagem--MG
Tel: +55 31 2191 4333
Fax: +55 31 2191 4440
CANADA
ESAB Group Canada Inc.
Missisauga, Ontario
Tel: +1 905 670 02 20
Fax: +1 905 670 48 79
MEXICO
ESAB Mexico S.A.
Monterrey
Tel: +52 8 350 5959
Fax: +52 8 350 7554
USA
ESAB Welding & Cutting Products
Florence, SC
Tel: +1 843 669 44 11
Fax: +1 843 664 57 48
Asia/Pacific
CHINA
Shanghai ESAB A/P
Shanghai
Tel: +86 21 5308 9922
Fax: +86 21 6566 6622
INDIA
ESAB India Ltd
Calcutta
Tel: +91 33 478 45 17
Fax: +91 33 468 18 80
INDONESIA
P.T. ESABindo Pratama
Jakarta
Tel: +62 21 460 0188
Fax: +62 21 461 2929
JAPAN
ESAB Japan
Tokyo
Tel: +81 3 5296 7371
Fax: +81 3 5296 8080
MALAYSIA
ESAB (Malaysia) Snd Bhd
Selangor
Tel: +60 3 8027 9869
Fax: +60 3 8027 4754
SINGAPORE
ESAB Asia/Pacific Pte Ltd
Singapore
Tel: +65 6861 43 22
Fax: +65 6861 31 95
SOUTH KOREA
ESAB SeAH Corporation
Kyungnam
Tel: +82 55 269 8170
Fax: +82 55 289 8864
UNITED ARAB EMIRATES
ESAB Middle East FZE
Dubai
Tel: +971 4 887 21 11
Fax: +971 4 887 22 63
ESAB AB
SE--695 81 LAXÅ
SWEDEN
Phone +46 584 81 000 www.esab.com
Representative offices
BULGARIA
ESAB Representative Office
Sofia
Tel/Fax: +359 2 974 42 88
EGYPT
ESAB Egypt
Dokki--Cairo
Tel: +20 2 390 96 69
Fax: +20 2 393 32 13
ROMANIA
ESAB Representative Office
Bucharest
Tel/Fax: +40 1 322 36 74
RUSSIA
LLC ESAB
Moscow
Tel: +7 095 543 9281
Fax: +7 095 543 9280
LLC ESAB
St Petersburg
Tel: +7 812 336 7080
Fax: +7 812 336 7060
Distributors
For addresses and phone numbers to our distributors in other countries, please visit our home page www.esab.com
060517