Digital fan control - Hartmann Electronic

advertisement
Digital
fan control
The digital fan control controls the speed of one or two 12 V fans according to
the temperature which is measured by a sensor.
The setup of the minimum and maximum temperature is done by a 6-pin
switch (SW1). Each 3-pin block of the switch defines one of the 2 temperatures.
Therefore the user can choose between 8 temperatures of the start and the
end of the temperature range. In the defined temperature range the power
of the fan is controlled between 20% and 100%. The digital parameter setup
without tuning ensures an easy installation.
Function of switch SW1
SW1.1
SW1.2
SW1.3
Größe
Wert
SW1.4
SW1.5
SW1.6
Größe
Wert
0
0
0
Tmax - Tmin
7,5 °C
0
0
0
Tmin
20 °C
0
0
1
Tmax - Tmin
10 °C
0
0
1
Tmin
22,5 °C
0
1
0
Tmax - Tmin
12,5 °C
0
1
0
Tmin
25 °C
0
1
1
Tmax - Tmin
15 °C
0
1
1
Tmin
27,5 °C
1
0
0
Tmax - Tmin
17,5 °C
1
0
0
Tmin
30 °C
1
0
1
Tmax - Tmin
20 °C
1
0
1
Tmin
32,5 °C
1
1
0
Tmax - Tmin
22,5 °C
1
1
0
Tmin
35 °C
1
1
1
Tmax - Tmin
25 °C
1
1
1
Tmin
37,5 °C
Sensor connector SV1
The sensor for the speed control can be connected between pin 1 and pin 2 of
SV1 or between pin 2 and pin 5 of SV3.
The sensor is a NTC-resistor.
Alarm connector SV2
If the maximum temperature exceeds, the pin 1 of the alarm connector is set
to GND by the open-collector-driver.
1
HARTMANN ELECTRONIC
BGT-Accessories
Digital
fan control
Open-Collector-GND.
Fan modulee connector SV3
SV3 is for the connection of the fan, the integrated LED and the temperature
sensor. The sensor is connected to pin 1 and pin 3, the LED to pin 2 and pin 4
and the fan motor to pin 3 and pin 6.
Connector for the second fan module SV4
The second fan motor can be operate on pin 3 and on pin 4 and the according
LED on pin 1 and on pin 2.
Power supply connection SV5
Power is supplied via pin 3 and pin 4 of SV5 for the digital fan control and the
fan. (It is compatible to the ATX power supply.)
Mating connectors and pins (e. g.):
housing
pins
mating connectors to
Molex 22-01-1022
Molex 50802-9101
Sensor connector SV1
Molex 22-01-1022
Molex 50802-9101
Alarm connector SV2
Molex 15-06-0060
Molex 39-00-0078
Fan modul connector SV3
AMP 171822-4
AMP 170204-1
Connector for the second fan
modul SV4
AMP 171822-4
AMP 170204-1
Power supply connection SV5
The proper operation of the fan function is displayed by a LED.
If the LED is ON, the fan operates properly. If the temperature exceeds the
maximum temperature by more than 2 °C, the LED starts flashing.
An open-collector-alarm-output can be used to signal the too high
temperature to a computer.
Thereby the user can profit of an advanced thermal management without
developing software.
Order number
Digital fan control, ext. sensor, rev. 01
1H00001801
HARTMANN ELECTRONIC
2
Download