FLUSH DOORFRAMES
SURFACE-FLUSH MODEL
Aluminium Flush Doorframes.
The well-defined and clear forms of flush frame models for doors and double glazing is one of Küffner’s trademarks. Distinct edge radii,
with a radius of only 0,5mm, as well as the characteristic appearance of anodized or powder-coated surfaces can be produced only with extruding aluminium profiles. The high quality of the surfaces and workmanship, in combination with a well-conceived mounting technology
ensures durability of the overall design, which fulfils the standards of sustainability. The sophisticated system of the basic frame, with the
attached aluminum plaster end profil or drywall finishing profiles, allows a practical mounting, by producing an exact wall opening, before
the completion of the wall surfaces. The two-layered aluminum frames are mounted at the very end, after the cleaning, plastering, painting
and
flooring work, together with the wooden or
glass doors.
USBV-G-48-5-42S
FZS48-5-42S
LZBS56-5-70SL
18
■ Model USBV-G
10
58
| The one with the Shadow gap
16
10
72
56
70
By combining the classic of our HARDLINE aluminium frames with a pre-mounted subframe, the shadow gap width can be variably adjusted between 3 and 13mm. In addition to the heavy duty hinges
with three-dimensional adjustability, the elevation width of the 40mm rebate side also allows for the
3
use of concealed hinges. The profile depth and rim width of these frames are prepared in the factory
48 (54)
44 (50)
mitred corner joints are screwed and glued in the factory. The 3-D fastening anchors allow for torsion-
44 (50)
48 (56)
3
to the thickness of existing walls. The material thickness amounts to a consistent 3mm, the consealed
free and exact mounting of the frames. For the purposes of consistent visual effects of the shadow
gap, the frames can be installed in combination with the flush skirting profile type XN or X (photograph
1, 2, 4,7+15)
FZS48-5-42S
40
LZBS56-5-70SL
3 10
18
18
■ Model FZS
10
10
15
18
| The Slim One
18
16
The sophisticated SLIMLINE frame with a double-sided elevation width of only 10mm represents the
intended “door frame” reduction. The slim face width of the aluminium frames, forms a discreet, mi72
56
70
nimalist door surround of the door leafs, protects against wall rubbing in the passage way, and forms
xxx
stable holding fixture for hinges and striking plate. The profile depth is based on the requirements of
xxx
Küffner
Aluzargen
GmbH
+ Co.
OHG
the wall thickness. By combining the aluminium frames with the flush skirting
profile
(type
X or
XN)
the
Die Drei Zargentypen zu ----
Kutschenweg 12 . 76287 Rheinstetten
3
+49 protrude
(0) 721 5169 0 up
info@kueffner.de
design allows for consistantcy from the wall to the floor. The frames mayFon:
also
to 10mm
erstellt am: 13.01.2011 von xxx
|
geändert am ---- von ----
|
Index ----
Fax: +49 (0) 721 5169 40 www.kueffner.de
over the surface of the wall for the purposes of counterbalancing tolerances or else to “raise”
the enY:\02-Druckvorstufe\Produktflyer\Wandbündige
Zargen\Bilder\WandbündigeZargen.dwg
3 10
tire door element away from the wall. For this purpose, the combination with the elevated aluminium
44 (50)
48 (54)
Schutzvermerk ISO 16016 beachten
skirting board type G is recommendable. (photograph 11)
■ Model LZBS
18
LZBS56-5-70SL
| The Corridor-side Surface Flush
18
10
15
The LZBS compliments the SLIMLINE frame and allows the door to be mounted flush with the wall on
the corridor side. The door openes into the soffit and thus into the rooms beyond. With a face width
18
of 18mm on either side, as well as a profile depth of 72mm, ideally, the construction can be combined
16
with doors of 70 mm thickness and a soffit rebate edge. The additional soffit cladding of the frames is
xxx
xxx
72
is recommended also with flush skirting profile of type X. (Photograph 12 +13) The well-defined and
56
70
tailored to the thickness of the walls. Due to the flush design of the door elements, the combination
Küffner
Aluzargen
+ Co.and
OHG double glazing is one of Küffner’s trademarks. Disclear forms of flush frame
models
forGmbH
doors
Die Drei Zargentypen zu ---erstellt am: 13.01.2011 von xxx
|
Schutzvermerk ISO 16016 beachten
Kutschenweg 12 . 76287 Rheinstetten
geändert am ---- von ----
|
Fon: +49 (0) 721 5169 0 info@kueffner.de
tinct edge radii, with a radius
of only 0,5mm, as well as the characteristic appearance of anodized or
Fax: +49 (0) 721 5169 40 www.kueffner.de
Index ----
Y:\02-Druckvorstufe\Produktflyer\Wandbündige
Zargen\Bilder\WandbündigeZargen.dwg
powder-coated surfaces
can be produced
only with extruding aluminium profiles. The high quality of
the surfaces and workmanship, in combination with a well-conceived mounting technology ensures
durability of the overall design, which fulfils the standards of sustainability. The sophisticated system
of the basic frame, with the attached aluminum plaster end profil or drywall finishing profiles, allows
a practical mounting, by producing an exact wall opening, before the completion of the wall surfaces.
18
10
15
The two-layered aluminum frames are mounted at the very end, after the cleaning, plastering, painting
and flooring work, together with the wooden or glass doors.
APPEARANCES
Aluminium Flush Doorframes.
1
2
5
6
9
13
1 + 2 |
3
10
11
14
15
11 |
12
16
4 |
9 |
frame type LZBS, cor-
soffit frames type FZS, mounted wall-flush, with skirting profile type X80
12 + 13 |
soffit frames type FZS, mounted projecting from the wall, combined with superimposed skirting profile G60
frames LZBS, 18mm mirror width, view from the room side
lush sof-
aluminium frames USBV-G with skirting profile X60
surface-flush aluminium frames type USBV-G with 4mm shadow gap and skirting profile X60
10 |
16
3 |
shadow gap frame type USBV-G in combination with flush skirting profile XN60
ridor side flush, with 18 mm view width
8
7
fit frames type FZS combined with surface-flush skirting profile X60
5 - 8 |
4
14 |
type EUROKS-G, 10mm shadow gap, 40mm mirror width type X80
soffit frame type FZS, flush mounting
16 |
15 |
soffit
sshadow gap frame
soffit frame type FZS, flush mounted, 10mm viewing width
THE DESIGN
Aluminium Flush Doorframes.
The Features.
The image of a Küffner frame is defined by its selection of material as well
as through a consistent language of forms.
With the objective of implementing good design in practice-oriented constructions, Küffner has spent decades developing and producing aluminium
frames, which, after completion of the walls and floors, are installed in one
go along with the wooden or glass door leaves.
For over 40 years Küffner frames have proved themselves for all types of
construction purposes and applications in the public and private spheres. Thus, only the highest construction standards, quality and durability,
through to the single-type reversibility of the products and 100% recycling
fulfil the requirements of a sustainable architecture.
Shadow gab frame type USBV-G
Soffit frame type FZS
The desire to build a frame into a wall opening flush with the surface and to
efficiently install it, led to the idea of a sub-frame. As a rule, this is delivered
in advance and installed along with the relevant aluminium rendering final
dry construction profile.
Sub-frames and rendering profiles are precisely bespoke prefabricated to
match and delivered by Küffner.
By the exact installation in rough wall openings in the building, the prerequisites are created for the later mounting of the aluminium frames. Here,
the perpendicularly mounted rendering profile of the basic frames, ensure
a smooth transition as well as an even wall thickness in the area of the wall
connection. The screed or fluid floor, as well as the flooring is followed by
a last dimensional measurement for the final production of the aluminium
frames for doors and glazing.
When inserting flush closed frames of the HARDLINE series or also MODERNLINE, the clamp-shell frame construction encompasses the basic frame
a form such that a surrounding shadow gap emerges. This shadow gap is
defined by the rendering or the final dry construction profile made of aluminium. As a rule, the surface of the shadow gap is selected to conform to
the frame surface, or else also painted with the wall surfaces. There are also
aluminium solutions with sub-frames and cover profile for the installa- tion
of exposed concrete or exposed masonry. In these cases, the unavoidable
construction tolerances can also be practically used with the shadow gap.
Soffit frames likewise describe Küffner flush frames, which are mostly
surface flush, but also occasionally built around a defined dimension protruding from the wall. The accompanying basic frames are likewise used
for producing an exact wall opening, whereby the rendering profile is no
longer visible after completion of the frame mounting. Depending on the
frame variation an all around shaddow gap can be profiled directly within
the aluminium frame so as to augment the sophisticated appearance, like
the SLIMLINE frame type NZS (not illustrated here).
The high manufacturing quality in combination with solid fixing technology
ensures an extraordinary durability of the Küffner frames, which, when required, can also be dismantled or exchanged without damage to the body
of the building.
■
Two part frame construction for subse-
quent installation
■ The mountings of frames and doors after
the rendering, painting and flooring
■ Suitable for various door thicknesses
■ Bespoke manufacturing to suit customers requirements
■
Innovative wall connecting forms and
possibilities
■
Extruded
and
aluminium
profiles
(AlMgSi0.5) EN AW-6060 T66 based on EN
573-3 and EN 755-2
■ High quality surfaces in anodised or powder coated surfaces based on the RAL, DB
or NCS colour scale
■ Pre-assembled mitred corners with concealed steel re-inforced corner fixing plates
■
Simple mountings and adjustments by
steel and screw-on anchor (partly 3-D adjustable)
■ Longevity and high mechanical durability
as well as chemical stability
■ High longevity by reversibility and deconstruction as well as recycling
■ Available with EI30 / FD30 fireproof doors
(Please get in touch with us for further information)
Aluminium door frames
Skirting profiles
Aluminium panels
Media pillars and ducts
Laminated glass elements
Barrier-free doors
Aluminium frames are frequently combined with flush aluminium frames
with suitable surface-flush wall profile or skirting boards. Further information as well as various finishes, advertisement texts, CAD data, enquiries
and ordering forms can be found on our homepage. Technical changes
reserved.
Soffit frames type LZBS
Küffner Aluzargen GmbH & Co. OHG
Kutschenweg 12
D - 76287 Rheinstetten
fon +49/721/5169-0
fax +49/721/5169-40
info@kueffner.de
www.kueffner.de