LOADCRAFT INDUSTRIES, LTD.
WE
BUILD
RIGS.
L O A D C R A F T I N D U S T R I E S , LT D .
RIGS
drawworks
WORKOVER
mud systems
PARTS/SERVICE
(80 0 ) 8 0 3 - 018 3
3811 N. BRIDGE
B R A D Y, T E X A S 7 6 8 2 5
www.LOADCRAFT.com
Drawworks
- LCI-2000 Single Drum Electric
- Drum Size 27 x 50
- Brakes 54 x 12 Water Circulating
Auxillary Brake
- Disc Model 336
Rotary Drive
- 752 Independent Electric Drive
Mast
- 147' x 1.2 mK (3 Section Free Standing)
- Crown - 12 Line String for 1 3/8” Wire Line
- Adjustable Racking Board
- 15,000' x 5" DP
- Top Head Drive Rails Included
- Mast Hydraulically Raised
Sub Structure
- Parallelogram 30' SUB
- Independent Rotary Drive for 37 1/2” Table
- Rotary Beam for 25' Clear Height (2 ea. x 25T)
- 1,200,000 lbs. Rotary Capacity
Available Options
- Traveling Frame
- Substructure
- Top Drive
- Rotary Drive
- Rotary Table
- 500 or 650 Ton Block
Drawworks
- LCI-1500 Single Drum Electric
- Drum Size 27 x 50
- Brakes 54 x 12 Water Circulating
Auxillary Brake
- Disc Model 336
Rotary Drive
- 752 Independent Electric Drive
Mast
- 147' x 1.0 mK (3 Section Free Standing)
- Crown – 10 or 12 Line String for 1 3/8” Wire Line
- Adjustable Racking Board
- 15,000' x 5" DP
- Top Head Drive Rails Included
- Mast Hydraulically Raised
Sub Structure
- Parallelogram 30' SUB
- Independent Rotary Drive for 37 1/2” Table
- Rotary Beam for 25' Clear Height (2 ea. x 25T)
- 1,000,000 lbs. Rotary Capacity
Available Options
- Traveling Frame
- Substructure
- Top Drive
- Rotary Drive
- Rotary Table
- 500 Ton Block
Generator House (10' W x 8' H x 45' L)
> One generator house with 1/4 crimped walls
> Two generator sets, one at each end of the skid
with MCC located at the center of the unit
> Two C15 generator sets at each end
MUD SYSTEM (1000 BBL)
Two Tank Mud System (12' W x 8' H x 50' L)
> 500 BBL suction tank - round bottom
> 500 BBL solids tank - round bottom
> 100 BBL pill tank
Trip Tank/Gas Buster
One 8' W x 40' L Skid with:
> One 2 1/16" x 4 1/16" 5,000 lbs. choke (four
2 1/16" 5,000 lbs. valves, four 4 1/16" 5,000 lbs.
valves, one cross, one 2 1/16" manual chokes)
on one end of skid. One end of skid plumbed for
2" hydraulic super choke
> One 50 BBL twin trip tank
> Two 2" x 3" centrifugal pumps with 20 HP
electric motors with 30" OD poorboy gasbuster
in center that lays over on choke to transport
Water Tank (10' W x 8' H x 40' L)
> 500 BBL water tank
> Two 2" x 3" centrifugal pumps 20 HP
> Water tank support dog house frame
Dog House (10' W x 20' L)
> One v-crimped top dog house that is placed in
position on top of the water tank to 18' sub floor
10,000 Gal. Fuel Tank (8' W x 8' H x 35' L)
One v-crimped square fuel tank
> Two 1 HP electric fuel charge pumps
> One 20' L v-crimped change house w/12
lockers and 1 bench
> 1/4 v-crimp walls
> One lubester tank (3 compartment)
Mud Pumps
> Two each 1,000 HP Triplex
> Master skids with pumps
> Cat 3508 Series engines for power, belt driven
> 5 x 6 charge pumps on master skid
Mud Pump Options
> Engine transmission drive system
Junk Basket / Closing Unit (8' x 36' Skid)
> Junk basket 8' x 20'
> Bop closing unit (10 bottle)
> Bop piping to end of skid
Locker / Parts Skid
> 1/4 v-crimp wall structure
> 8' x 15 1/2' tool room
> 8' x 17 1/2' locker room
> Front skid with two 25 HP air compressors
> Lites, knowledge box, and 4 lockers
Solids
Equipment
> Per customer
order
Mechanical Drawworks Model 1100/4212
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 7"
> Single line pull is 51,800 lbs.
> Design with 2 x C15 power @ 540 HP
> Two speed transmission shaft
> High and low speed clutch assembly
> Torque converter w/engine
> Wichita 325 Auxiliary brake standard
Drawworks Options
> Parmac Model V80 hydrobrake
> LEBUS grooving on main drum - 1 1/8" diameter
> Crown block saver
Mast Model 122 x 440 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 122' below crown.
> Static hook load capacity: on 10 lines 440,000 lbs.
> Crossover crown with 36" fast-line sheave plus five 30" sheaves
> All sheaves mounted on Timken double-row bearings
> Racking capacity 12,000' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes, hydraulic catheads
Drive Train
> Power is by twin Cat C15 @ 540 HP w/torque converters
> Chain drive with oil spray lubrication
> Two-speed transmission shaft with high & low drum clutch shaft
> Shifting is done with air activated jaw clutch
> Main drive is 1 1/2 triple, two-speed is by 1 3/4 triple chain
Trailer
> Four axle heavy duty trailer is main frame
> Four axle heavy duty air ride suspension @ 25,000 lbs. capacity
> Attachments are ready for rear dolly and front jeep
Trailer Options
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Dollies
> Front Attachment: 2 axle jeep dolly
> Rear Attachment: 2 axle rear air ride dolly
Controls and Hydraulic System
> Hydraulic power is supplied from 65 HP electric motor APU
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. or 12,000 lbs. catline winch for safe,
efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure - Hydraulic Telescopic type
> Rotary chain case drive
> Optional 5th trailer axle with lift
Electric Drawworks Model 1100/4212-42
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 7"
> Single line pull is 51,800 lbs.
> Design with 2 x 762 motors 600 HP
> Two speed transmission shaft
> High and low speed clutch assembly
> Wichita 325 Auxiliary brake standard
Drawworks Options
> Parmac Model V80 hydrobrake
> LEBUS grooving on main drum - 1 1/8" diameter
> Crown block saver
Mast Model 122 x 440 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 122' below crown.
> Static hook load capacity: on 10 lines 440,000 lbs.
> Crossover crown with 36" fast-line sheave plus five 30" sheaves
> All sheaves mounted on Timken double-row bearings
> Racking capacity 12,000' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes, hydraulic catheads
Drive Train
> Power is by twin 762 electric motors
> Chain drive with oil spray lubrication
> Two-speed transmission shaft with high & low drum clutch shaft
> Shifting is done with air activated jaw clutch
> Main drive is 1 1/2 triple; two speed is by 1 3/4 triple chain
Trailer
> Four axle heavy duty trailer is main frame
> Four axle heavy duty air ride suspension @ 25,000 lbs. capacity
> Attachments are ready for rear dolly and front jeep
Trailer Options
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> Hydraulic power is supplied from 4 cylinder diesel in
combination with 65 HP electric motor APU
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. or 12,000 lbs. catline winch for safe,
efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure - Hydraulic Telescopic type
> Rotary chain case drive
> Optional 5th trailer axle with lift
Drawworks Model 1100/4212-42
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 7"
> Single line pull is 51,800 lbs.
> Outboard P0230 clutch
> Wichita 325 Auxiliary brake standard
Drawworks Options
> Parmac Model V80 hydrobrake
> LEBUS grooving on main drum - 1 1/8" diameter
> Rotary drive-torque shaft from right angle box
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 122 x 440 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 122' below crown.
> Static hook load capacity:
on 8 lines 400,000 lbs.
on 10 lines 440,000 lbs.
> Crossover crown with 36" fast-line sheave plus five 30"
sheaves
> All sheaves mounted on Timken double-row bearings
> Racking capacity 12,000' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes, 24" sandline sheave
> Hydraulic cathead assembly
Drive Train
> Twin C15 or Ser 60 Detroit (475 to 540 HP Twin engine)
> Allison CLT 6061 transmission
> Optional M6610 Allison transmission (gear driven compound
behind the transmissions)
> Engine, transmission, and compound mounted in rubber
above deck for easy access
> Pressure lubricated combination right-angle box/drop box for
drive to drawworks, rotary drive
Trailer
> Four axle heavy duty trailer is main frame
> Four axle heavy duty air ride suspension @ 25,000 lbs. capacity
> Attachments are ready for rear dolly and front jeep
Trailer Options
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 12,000 lbs. catline winch for safe, efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure - Hydraulic Telescopic type
> Rotary chain case drive
> Optional 5th trailer axle with lift
Drawworks Model 1000/4212-42
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 6 1/2"
> Single line pull is 45,000 lbs.
> Outboard Eaton (Fawick) clutch
> Parmac Model 202 Auxiliary brake standard
Sandline Drum
> Demountable, forged steel brake rims are 42" diameter x 8"
wide
> Water splash brake cooling
> Wireline capacity per AOSC approved formula:
16,500' of 9/16"
13,400' of 5/8"
> Outboard Eaton (Fawick) clutch
Drawworks Options
> LEBUS grooving on main drum - 1 1/8" diameter
> Rotary drive-torque shaft from right angle box
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 116 x 410 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 116' below crown.
> Static hook load capacity:
on 8 lines 360,000 lbs.
on 10 lines 410,000 lbs.
> Crossover crown with 36" fast-line sheave plus five 30" sheaves
> All sheaves mounted on Timken double-row bearings
> Racking capacity 10,080' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes, 24" sandline sheave
> Optional Mast Model 114 x 350 gives 114' clear height and
350,000 lbs. capacity on 8 lines
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. or 12,000 lbs. catline winch for safe,
efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure -Hydraulic Telescopic type
> Rotary chain case drive
Drawworks Model 1000/4212-42
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 6 1/2"
> Single line pull is 45,000 lbs.
> Outboard Eaton (Fawick) clutch
> Parmac Model 202 Auxiliary brake standard
Drawworks Options
> LEBUS grooving on main drum - 1 1/8" diameter
> Rotary drive-torque shaft from right angle box
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 116 x 410 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 116' below crown.
> Static hook load capacity:
on 8 lines 360,000 lbs.
on 10 lines 410,000 lbs.
> Crossover crown with 36" fast line sheave plus five 30" sheaves
> All sheaves mounted on Timken double row bearings
> Racking capacity 10,080' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes, 24" sandline sheave
Drive Train
> Twin C15 or Ser 60 Detroit (475 to 540 HP Twin engine)
> Allison CLT 6061 transmission
> Optional 6610 Allison Series (gear driven compound behind the
transmissions)
> Engine, transmission, and compound mounted in rubber above
deck for easy access
> Pressure lubricated combination right-angle box/drop box for
drive to drawworks, rotary drive, and rear bogies
Carrier - Seven axle
> Three front steering axles (rated at 22,000 lbs. each) have
spring suspension
> Rear tandem driving axles (rated at 50,000 lbs. total) have
walking beam suspension
> Third driver rear axle with air bag lift suspension is rated at
25,000 lbs. capacity
> Pusher axles with air lift suspension is rated at 25,000 lbs.
capacity
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. or 12,000 lbs. catline winch for safe,
efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure - Hydraulic Telescopic type
> Rotary chain case drive
Drawworks Model 750/4212-42
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 6 1/2"
> Single line pull is 45,000 lbs.
> Outboard Eaton (Fawick) clutch
> Parmac Model 202 Auxiliary brake standard
Sandline Drum
> Demountable, forged steel brake rims are 42" diameter x 8"
wide
> Water splash brake cooling
> Wireline capacity per AOSC approved formula:
16,500' of 9/16"
13,400' of 5/8"
> Outboard Eaton (Fawick) Clutch
Drawworks Options
> LEBUS grooving on main drum - 1 1/8" diameter
> Rotary drive-torque shaft from right angle box
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 116 x 365 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 116' below crown.
> Static hook load capacity:
on 8 lines 350,000 lbs.
on 10 lines 365,000 lbs.
> Crossover crown with 36" fast line sheave plus five 30" sheaves
> All sheaves mounted on Timken double row bearings
> Racking capacity 10,080' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes, 24" sandline sheave
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. catline winch for safe, efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure - Hydraulic Telescopic type
> Rotary chain case drive
Drawworks Model 750/4212-42
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Brakes are cooled by circulating water
> Drum shaft diameter is 6 1/2"
> Single line pull is 45,000 lbs.
> Outboard Eaton (Fawick) clutch
> Parmac Model 202 Auxiliary brake standard
Drawworks Options
> LEBUS grooving on main drum - 1 1/8" diameter
> Rotary drive-torque shaft from right angle box
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 116 x 365 Twin Box (per API 4F)
> Twin box leg fixed base design allows fast positioning of rig
before mast is raised. Clear height is 116' below crown.
> Static hook load capacity:
on 8 lines 350,000 lbs.
on 10 lines 365,000 lbs.
> Crossover crown with 36" fast line sheave plus five 30" sheaves
> All sheaves mounted on Timken double row bearings
> Racking capacity 10,080' of 4 1/2" drill pipe
> Two hydraulic raising rams and two hydraulic telescoping rams
> 1 1/8" wire line standard
Mast Options
> Mast lights, standpipes
Drive Train
> Twin C15 or Ser 60 Detroit (475 to 540 HP Twin engine)
> Allison CLT 6061 transmission
> Optional 6610 Allison Series (gear driven compound behind the
transmissions)
> Engine, transmission, and compound mounted in rubber above
deck for easy access
> Pressure lubricated combination right-angle box/drop box for
drive to drawworks, rotary drive, and rear bogies
Carrier - Seven Axle
> Three front steering axles (rated at 22,000 lbs. each) have
spring suspension
> Rear tandem driving axles (rated at 50,000 lbs. total) have
walking beam suspension
> Third driver rear axle with air bag lift suspension is rated at
25,000 lbs. capacity
> Pusher axles with air lift suspension is rated at 25,000 lbs.
capacity
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission, and main drum are located
at one position for simple, quick rig-up. Operator's console can
be provided movable to 12', 15', or 18' 6".
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. or 12,000 lbs. catline winch for safe,
efficient lifting
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure - Hydraulic Telescopic type
> Rotary chain case drive
Drawworks Model 550/42-12, 42-8
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Drum shaft diameter is 6 1/2"
> Single line pull is 42,500 lbs.
> Parmac Model 202 Auxiliary brake standard
Sandline Drum
> Demountable, forged steel brake rims are 42" diameter x 8"
wide
> Wireline capacity per AOSC approved formula:
14,400' of 9/16"
11,800' of 5/8"
> Outboard clutch for easy access
Drawworks Options
> Water splash brake cooling
> LEBUS grooving for main drum - 1" diameter
> Rotary drive attachment @ rear of rig
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 104/250 (Double Tubing, Triple Rods per API 4F)
> Four leg fixed base design allows fast positioning of rig before
mast is raised. Clear height is 104' below crown.
> Static hook load capacity:
on 6 lines 225,000 lbs.
on 8 lines 250,000 lbs.
> Crossover crown with 36" fast line sheave plus 24" sheaves for
cluster; 30" deadline. Sandline 9/16 x 24" sheave.
> All sheaves mounted on Timken double row bearings
> Racking platform capacity 22,200' of 2 7/8" EUE tubing
> 1" wire line standard
Mast Options
> Mast lights, rod hangers, work platform, standpipes, 24"
sandline sheave
> Optional Mast Model:
96/250 tubing mast
110/250 tubing mast
104/250 twin box mast
110/250 twin box mast
Drive Train
> Cat C15 or Ser 60 Detroit (475 to 540 HP)
> Allison CLT 6061 six speed automatic transmission
> Optional 5610 Allison or equal (engine and transmission
mounted in rubber on carrier for easy above-deck access)
> Engine cover for weather protection
Carrier – Five Axle
> Front axles (rated at 22,000 lbs. each) have spring suspension
> Rear tandem axles (rated at 50,000 lbs. total) have walking
beam suspension
> Third (non-driving) rear axle with air bag lift suspension is rated
at 25,000 lbs. capacity
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Three rear drive axles for off road
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission and main drum located at
one position for simple, quick rig-up. Operator's console can be
provided movable to 10'-6", 12', or 15' as required.
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. hyd. catline winch located at rear of rig
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool
> Mast lite package
> Rig ramps and crossbase supports
> Rig substructure assembly
Drawworks Model 350/42-12, 38-8
Main Drum
> Demountable, forged steel brake rims are 42" diameter x 12"
wide
> Drum shaft diameter is 5 3/4"
> Single line pull is 37,500 lbs.
> 1" wire line size standard
Sandline Drum
> Demountable, forged steel brake rims are 38" diameter x 8"
wide
> Wireline capacity per AOSC approved formula:
12,760' of 9/16"
10,530' of 5/8"
Drawworks Options
> Drawworks Model 350/42-10, 38-8
> Water splash brake cooling
> Parmac Model 122 hydrobrake
> LEBUS grooving standard on main drum - 1" diameter
> Rotary drive attachment.
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 96/225 (Double Tubing, Triple Rods per API 4F)
> Mast Options four leg fixed base design allows fast positioning
of rig before mast is raised. Clear height is 96' below crown.
> Static hook load capacity:
on 4 lines 180,000 lbs.
on 6 lines 225,000 lbs.
> Crossover crown with 30" fast line sheave plus three 24"
sheaves
> All sheaves mounted on Timken double row bearings
> Racking platform capacity 19,200' of 2 7/8" EUE tubing
> Hydraulic rams for raising and telescoping
Mast Options
> Mast lights, rod hangers, work platform, standpipes, 24"
sandline sheave
> Optional Mast Model:
104/225 available for 104' clear height
96/225 twin box mast
104/225 twin box mast
Drive Train
> Cat or Detroit Ser 60 (400 to 450 HP) Allison CLT 5961 six
speed transmission (engine and transmission mounted in
rubber on carrier for easy above-deck access)
> Engine cover for weather protection
Carrier
> Four axle carrier for special weight conditions
> Std. five axle carrier offered as required for heavy duty
configurations
> Front axles (rated at 22,000 lbs. each) have spring suspension
> Rear tandem axles (rated at 50,000 lbs. total) have walking
beam suspension
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Third (non-driving) rear axle with air bag lift suspension is rated
at 25,000 lbs. capacity
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission and main drum located at
one position for simple, quick rig-up. Operator's console can be
provided movable to 10'-6", 12', or 14' as required.
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> 70 gpm hydraulic pump (hydraulic oil cooler for continuous use
and hot climate applications)
> Single or dual 8,000 lbs. hyd. catline winch located at rear of rig
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool on rig
> Mast lite package
> Rig ramps and crossbase assembly.
> Rig substructure assembly
Drawworks Model 250/38-10, 38-8
Main Drum
> Demountable, forged steel brake rims are 38" diameter x 10"
wide (drum shaft diameter is 5 3/4")
> Single line pull is 37,500 lbs.
> 1" wire line size standard
Sandline Drum
> Demountable, forged steel brake rims are 38" diameter x 8"
wide
> Wireline capacity per AOSC approved formula:
12,760' of 9/16"
10,530' of 5/8"
Drawworks Options
> Drawworks Model 250/38-10, 38-8
> Water splash brake cooling
> LEBUS grooving on drum - 1" diameter
> Rotary drive attachment
> Crown block saver
> Disc brake in lieu of Parmac Auxiliary brake
Mast Model 96/180 (Double Tubing, Triple Rods per API 4F)
> Four leg fixed base design allows fast positioning of rig before
mast is raised. Clear height is 96' below crown.
> Static hook load capacity:
on 4 lines 180,000 lbs.
on 6 lines 225,000 lbs.
> Crossover crown with 24" fast line sheave plus three 24"
sheaves
> All sheaves mounted on Timken double row bearings
> Racking platform capacity 18,360' of 2 7/8" EUE tubing
> Hydraulic rams for raising and telescoping
Mast Options
> Speed kit crown, mast lights, rod hangers, work platform,
standpipes, 24" sandline sheave
> Optional Mast Model:
96/225 twin box mast
71/150 twin box mast
Drive Train
> Cat or Detroit (230 to 325 HP) Allison five speed transmission
> Engine and transmission mounted in rubber on carrier for easy
above-deck access
> Engine cover for weather protection
Carrier
> Four axle carrier available with long wheelbase (338") for even
weight distribution or with short wheelbase (297") for a
shorter turning radius
> Front axles (rated at 22,000 lbs. each) have spring suspension.
> Rear tandem axles (rated at 50,000 lbs. total) have walking
beam suspension
Carrier Options
> Two powered front steering axles are optional for use in rough
or muddy terrain
> Trailer models are available with either a single drop
(gooseneck) or straight (rough terrain) design
> Tool boxes, extra fuel tanks, spare tires, operator platforms can
be supplied as needed
Controls and Hydraulic System
> The console panel for all leveling jacks, mast raising and
extending cyl., engine, transmission and main drum located at
one position for simple, quick rig-up. Operator's console can be
provided movable to 10'-6", 12', or 14' as required.
> 50 gpm hydraulic pump for all rig hydraulics and tong operation
> Filters provided on pressure and return lines
Options
> Hydraulic oil cooler for continuous use and hot climate
applications
> Single or dual 8,000 lbs. hyd. catline winch for safe, efficient
lifting around the well site
> Hydraulic catworks for precise control of make-up and break-out
torques
> Cold weather packages for -40° operation
> Folding platforms off operator side of rig
> Spare line spool on rig
> Mast lite package
> Install drawworks on conventional truck
The Best Products, Built by the Best People, for the Best Clients
...Throughout the World.
(800)8 0 3 - 018 3
3 8 1 1 N . B R I D G E • B R A D Y, T E X A S 7 6 8 2 5
www.LOADCRAFT.com
LOADCRAFT INDUSTRIES, LTD.
MADE
IN
TEXAS
L O A D C R A F T I N D U S T R I E S , LT D .
LOADCRAFT INDUSTRIES LTD.
Manufacturing Plant at Brady, Texas
325-597-2911• 325-597-0781
http:www.loadcraft.com
MAST API 4F FOURTH EDITION GENERAL SPEC GUIDELINE
LCI mast is designed to withstand a wind of 69 mph from any direction provided the four jacks on the vehicle are
properly deployed and guying per API is done. Telescoping structural mast is designed and constructed to API
standard Spec 4-F (Fourth Edition) and API Spec Q-1 quality control (Eighth Edition) and bears the API
monogram. The Product Specifcation Level for this mast is PSL 1, and the Structural Safety Level (SSL) is E2U2.
Section 4: Product Specification Levels (PSL)… PSL 1 Required
The level of material and process controls placed upon primary load-carrying components of covered equipment.
PSL 1
//////////
Section 5.2, 5.3, 5.4: API Nameplates Required… API Service Rig Mast Nameplate Required
No
API Derrick or Mast Nameplate Required
______
Yes
___X__
Yes
______
No
API Service Rig Mast Nameplate Required
___X__
No
API Substructure Nameplate Required
______
Yes
___X__
No
API Crown Block Nameplate Required
______
Yes
___X__
Section 6: Structural Safety Level (SSL)… Medium E2 U2 Required
Other Concerns
(Pollution, Economic Loss, Public Concern, etc.)
Life Safety
High
Medium
Low
High
E1
U1
E1
U1
E1
U1
Medium
E1
U1
E2
U2
E2
E2
Low
E1
U1
E2
U2
E3
U3
E = Expected Environmental Event (Choose Only One)
U = Unexpected Environmental Event (Choose Only One)
Each structure shall have two SSL’s, the first for the expected environmental event, and the second for the
unexpected environmental event.
Section 7: Design Loads… Design loads are specific to each rig.
kN (kips)
Maximum Rated Static Hook Load =
Varies
kN (kips)
Maximum Rated Static Rod Load =
Varies
kN (kips)
Maximum Rated Static Rotary Load =
Varies
kN (kips)
Maximum Rated Setback Load =
Varies
1. Operating Rod Load required for Service Rig Masts per Table 7.2.
Section 8.1.1: Fatigue Design … Not Required
Section 8.2: Special Operating Loads… Not Required
Section 8.3.1.1: Onshore Wind Design Criteria…
The design reference wind velocity for operating, erection, and transportation shall be specified by the purchaser.
Operating Vref =
Erection Vref =
Transportation Vref =
25
25
25
knots
knots
knots
1
LOADCRAFT INDUSTRIES LTD.
Manufacturing Plant at Brady, Texas
325-597-2911• 325-597-0781
http:www.loadcraft.com
Note: 1 knot = 1.15 miles per hour = 0.514 meters per second
The expected and unexpected storm wind data may be specified in one of the following manners:
1. Directly specified by the purchaser in knots: The expected wind velocity specified shall be a 3-second
gust wind, in knots, measured at 10 m (33 ft) in open terrain with an associated wind return period of 50
years for the land regions where the rig will operate.
The unexpected wind velocity shall be not less than 75% of the expected wind velocity.
2. Specified by the required Structural Safety Level (SSL; refer to Section 6) and the various regions where
the structures shall operate. The manufacturer shall determine the appropriate design wind speeds using
data from a recognized standards or governmental meteorological agency for the regions of intended use.
Example: ASCE/SEI 7-05 is used for data in the continental United States. Note that for some regions
in the world, such meteorological data is not readily available and the purchaser and manufacturer should
agree on appropriate design wind speeds.
Expected Vref =
Unexpected Vref =
75
60
knots
knots
Section 8.3.1.2: Offshore Wind Design Criteria… Not required
Section 8.4: Dynamic Loads… Not required
Section 8.5: Earthquake Load… Required upon special application.
Earthquake consideration is a special loading condition to be specified by the user. The purchaser is responsible
to provide all design criteria for the seismic zone in which the drilling unit shall operate.
Section 8.7: Erection Loads… Reference Standard Equipment Spec
Per API requirements, each drilling structure shall be designed for erection loads in combination with dead loads
and erection wind. Any additional erection loads, wind, inertial, or other, shall be specified by purchaser.
Section 8.8: Transportation Loads… Reference Standard Equipment Spec
Per API requirements, each drilling structure shall be designed for transportation loads in combination with dead
loads and transportation environment wind. Any additional transportation loads, wind, inertial, or other, shall be
specified by purchaser.
Section 8.9: Overturning and Sliding… Reference Standard Equipment Spec
Distribution of any foundation support reactions shall be limited to comply with allowable design loadings of the
supporting structures foundations, if specified by the purchaser. Manufacturer shall include diagrams defining the
maximum foundation support loads based on the factored lateral loads with rig instructions. For example, ground
supported land drilling structures might be specified to be supported on rig mats with an appropriate limitation on
the maximum allowable ground bearing pressure.
2