LAMINEX WALL PANEL
®
SOLUTIONS
FABRICATION AND INSTALLATION GUIDE
IMPORTANT NOTES
1. Suitable for internal use only
2. Failure to install or maintain this product in accordance with applicable building codes, regulations, standards and
Laminex’s instructions may lead to personal injury, affect system performance, violate building codes and void the
product warranty.
3. Laminex will only warrant the system when used with tested and approved Laminex decorative panels. For Laminex
panels not featured in the matrix, refer to your Laminex Representative for more information.
4. The strength of the system is dependant on the installer ensuring that all fasteners are firmly screwed to framework.
5. All panels should be pre-conditioned on-site for 48 hours before hanging.
RESPONSIBILITY
The specifier or person responsible for the project must ensure that the details in this instruction are appropriate for the
intended application and that additional detailing is performed for details that are not specified in these instructions.
FRAMING
Framing tolerances must be within 3mm over any 3000mm length of the frame. Frame must be square, straight and true.
Timber
All frames must be constructed in accordance with AS/NZS 1684 and be 35mm or wider. Ensure that all fasteners used
penetrate framing by at least 30mm.
Steel
All frames must be constructed in accordance with NASH standard Part 1.
Using Button-Fix over existing internal linings
Ensure that all fasteners used penetrate existing linings and are firmly screwed into studwork by at least 30mm. Laminex
recommends that wooden battens of 35mm x 45mm pine or 16mm MDF are used over existing plaster or masonary wall
linings.
Bracing
Laminex Button-Fix is not suitable for the provision of any bracing load resistance.
HOW IT WORKS
ATTACHING THE BUTTON
Choose an appropriate 5mm counter sunk screw to Lime greenLime
green Button
Button
forØ5mm
use with Ø5mm
for use with
provide >30mm engagement into the supporting structure.
Orange
Orange Button
forButton for
use with Ø6.2mm
use with Ø6.2mm
Varianta
Varianta Euro
screwEuro screw
countersunk
wood screw
countersunk
wood screw
NOTE: Plasterboard is not strong enough to support
a Button
Lime
green
Limegreen
green
Button
Lime
green
Button
Lime
Button
Lime
green
Button
for
use
with
Ø5mm
for
use
with
Ø5mm
Laminex Decorative panel with Button-Fix. Secure
Buttons
foruse
usewith
with
Ø5mm
for
Ø5mm
Lime
green
Button
for
use with Ø5mm
countersunk
wood
screw
countersunk
woodscrew
screw
countersunk
wood
screw
countersunk
wood
for
use with Ø5mm
countersunk
wood
screw
into studwork or battens only.
countersunk wood screw
Orange
Button
for
OrangeButton
Buttonfor
for
Orange
Button
for
Orange
Orange
Button
for
use
with
Ø6.2mm
usewith
with
Ø6.2mm
use
with
Ø6.2mm
use
Ø6.2mm
Orange
Button
for
use
with Euro
Ø6.2mm
Varianta
Euro
screw
Varianta
Euroscrew
screw
Varianta
Euro
screw
Varianta
use
with Ø6.2mm
Varianta
Euro
screw
Varianta Euro screw
TYPE 1 FIX
The Type 1 Fix connects parallel
panels and is ideal for applications
where strength and security are
paramount.
15mm fall 15mm
to
fall to
engage panel
engage panel
15mm
15mmfall
fall
fallto
toto
to
15mm
15mm
fall
engage
engagepanel
panel
panel
engage
engage
panel
15mm
fall
to
15mm fall to
engage panel
panel
engage
Engage the Buttons in the Fixes and
slide the panel down by 15mm until
Button-fix goes ‘click’. The Type 1 Fix
can also be configured for sideways
assembly.
When surface-mounted, the Type
1 Fix creates an 8mm gap between
the two attaching panels.
Alternatively, you can rebate the Type
1 Fix, to reduce the gap between the
two attaching panels to only 3mm.
Do not use the REBATE
method with Compact
Laminate – as this reduces
the systems tolerance to
changes in panel dimensions
as humidity changes.
TYPE 2 FIX
The Type 2 Fix connects panels at
90° with a simple push/pull fit. It
is ideal for applications where the
emphasis is more on ease of fit
and less on strength. Unlike Type 1,
the Type 2 Fix does not require a
15mm dropdown engagement.
Ø5mm panØ5mm
head wood
screws
pan head
wood screws
for surface-mounted
Fix
for surface-mounted
Fix
Ø5mm
Ø5mm
pan
head
wood
screws
Ø5mm
Ø5mmpan
pan
panhead
head
headwood
wood
woodscrews
screws
screws
for
for
surface-mounted
surface-mounted
Fix
Fix
for
for
surface-mounted
surface-mounted
Fix
Fix
Ø5mm
wood screws
screws
Ø5mm pan
pan head
head wood
for
Fix
for surface-mounted
surface-mounted Fix
Panel
drilling
Panel
drilling
Panel
Panel
Panel
Panel
drilling
drilling
drilling
drilling
Panel
Panel
drilling
drilling
Ø4.5mm countersunk
wood
Ø4.5mm countersunk
wood
screws forscrews
rebatedfor
Fixrebated Fix
Ø4.5mm
Ø4.5mmcountersunk
countersunk
countersunkwood
wood
wood
Ø4.5mm
countersunk
wood
Ø4.5mm
screws
screwsfor
for
forrebated
rebated
rebatedFix
Fix
Fix
screws
for
rebated
Fix
screws
Ø4.5mm countersunk
countersunk wood
wood
Ø4.5mm
Ø4.5mm pan
Ø4.5mm pan
screws for
for rebated
rebated Fix
Fix
head woodhead woodscrews
screws forscrews
Fix
for Fix
Ø4.5mm
pan
Ø4.5mmpan
pan
Ø4.5mm
pan
Ø4.5mm
head
wood
headwood
wood
head
wood
head
screws
for
Fix
screwsfor
forFix
Fix
Ø4.5mm
pan
screws
for
Fix
screws
head wood
screws for Fix
IMPORTANT: The integrity of the Laminex Wall Panel Solutions system is dependant on the installer providing a sound
support to the system such as stud work, framing or battens.
THE SECRET FIXING FOR PANELS
The Button-fix range of fasteners
and accessories is:
BUTTONS
1. Lime green Button for
countersunk (5mm) wood
screws.
2. Orange buttons for Euro
screws/varianta. (Diameter
6.2mm countersunk).
1.
2.
FIXES
3. Type 1 Fix for connecting parallel
panels. (Diameter 5mm pan head
for face fixing. Diameter 4.5mm
countersunk for rebated fixing.)
4. Type 2 Fix for connecting 90°
panels. (Diameter 4.5mm pan
head.)
3.
4.
5.
6.
7.
8.
MARKER ACCESSORIES
5. Button marker accessory for
use with Type 1 Fixes.
6. Fix marker accessory for use
with Type 2 Fixes (and can also
be used with Type 1).
Marker accessories need to be
ordered separately from the
Button-fixes.
OTHER ACCESSORIES
7. Security cord accessory for use
with Type 2 Fixes.
8. Router jig for use when
recessing Type 1 Fixes.
These accessories need to be
ordered separately from the
Button-fixes.
ACCESSORIES
BUTTON MARKER
This re-usable accessory helps to
accurately align the Buttons with
Type 1 Fixes. Snap a marker into
each Fix, then position the second
panel and press firmly. The markers
will leave indents in the panel
surface, which can be used as pilot
guides for the Buttons.
FIX MARKER
This re-usable accessory helps to
accurately align Type 2 Fixes. The
marker is assembled onto the Fix
and used to position the Button
from the panel edge. After fixing
the Button, position the second
panel and press firmly. The marker
will leave indents in the panel
surface, which can be used as
guides when drilling pilot holes for
the Fix.
The marker can be used for
internally mounted panels, but
must be assembled in the opposite
orientation, as shown on the right.
Tip: use some adhesive tape to
stop the marker and Fix assembly
rotating on the Button.
SECURITY CORD ACCESSORY
This accessory should be installed with the Type 2 Fix in situations where safety
is an issue. On a vertical panel install two Security Cords, one to each Fix in the
top corners.
An additional Button is used to capture the loop on the Security Cord, installed
adjacent to the fixing Button. To remove the panel completely, ease the loop on
the Security Cord off the Button.
Please note that accessories must be ordered separately from the Button-fixes.
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
Button-fix is designed for furniture construction
Lime green Button
for use with Ø5mm
countersunk
screw
and
interiorwood
fittings.
Orange Button for
use with Ø6.2mm
Varianta Euro screw
Provided that the screws and substrate are properly matched, a vertical panel fixed with four Type 1 Fixes can safely weigh
200kg. For critical applications it is essential to perform your own tests.
Avoid any contact with aggressive solvents and cleaning products.
SUGGESTED LAYOUT
– MDF, PB & PLYWOOD
MAX 1000
As an approximate guide, we suggest
that Button-fix centres are no greater
than 1000mm apart and no closer
than 35mm to the edge of the panel.
MAX 1000
MAX 1000
Always remember to allow at least
15mm clearance for the removable
panel to disengage.
600
60
1200
Allow 3mm space minimum
between panels.
Max
1000
Lime green Button
for use with Ø5mm
countersunk wood screw
2700
Orange Button for
use with Ø6.2mm
Euro
Max screw
Max
300Varianta
2400
1000
Max
300
SUGGESTED LAYOUT
– COMPACT LAMINATE
MAX 450
As an approximate guide, we suggest
that Button-fix centres are no greater
than 450mm apart and no closer
than 35mm to the edge of the panel.
MAX 450
MAX 450
Always remember to allow at least
15mm clearance for the removable
panel to disengage.
600
600
1200
Allow 5mm space minimum
between panels.
2700
1200
Max
1000
Max
450
2400
Max
300
Max
1000
Max
300
2700
Max
200
2400
Max
450
Max
200
MAX
MAX1000
1000
MAX
MAX1000
1000
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
BUTTON MARKER ACCESSORY
MAX1000
1000
The Button marker MAX
accessory
helps to mark out where to install the Buttons.
Once you have attached the Fix mouldings (see following pages), snap a marker into each one. Then position the second panel
and press firmly. The markers will leave indents in the panel surface, which can be used as guides for drilling pilot holes for the
Buttons.
Remove the markers, which can be re-used to mark out the next panel.
SURFACE-MOUNTED FIX
Surface mounting creates an 8mm gap between the two panels. The Fix can be configured in three options:
1. BUTTON ON REMOVABLE PANEL
The Fix is attached to the background structure, pointing upwards as shown in the diagrams on the right.
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
x2Ø5mm
x Ø5mm
2 x2 Ø5mm
panpanpan
head
wood
screws
head
wood
screws
head
wood
screws
x2Ø5mm
x Ø5mm
2 x2 Ø5mm
panpanpan
head
wood
screws
head
wood
screws
head
wood
screws
15mm
to to
15mm
15mm
fallfall
tofall
engage
panel
engage
panel
engage
panel
Panel
Panel
Panel
drilling
drilling
drilling
15mm
to to
15mm
15mm
fallfall
tofall
engage
panel
engage
panel
engage
panel
Panel
Panel
Panel
drilling
drilling
drilling
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
2. FIX ON REMOVABLE PANEL
xØ5mm
Ø5mm
2 x Ø5mm
pan pan
15mm
15mm
falltoto
fall to
PanelPanel
2 2x Fix
pan
15mm
fall
The
is attached
to the removable panel, pointing
downwards
as shown in the diagrams onPanel
the right.
headwood
head
wood
wood
screws
screws
head
screws
engage
engage
panelpanel
engage
panel
drilling
drilling
drilling
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
x2Ø5mm
x Ø5mm
2 x2 Ø5mm
panpanpan
head
wood
screws
head
wood
screws
head
wood
screws
Ø5mm
2 x Ø5mm
pan pan
2 2x xØ5mm
pan
headwood
head
wood
wood
screws
screws
head
screws
15mm
to to
15mm
15mm
fallfall
tofall
engage
panel
engage
panel
engage
panel
Panel
Panel
Panel
drilling
drilling
drilling
15mm
fall to
15mm
falltoto
15mm
fall
engage
engage
panelpanel
engage
panel
PanelPanel
Panel
drilling
drilling
drilling
3. SIDEWAYS ARRANGEMENT
The Fix is attached to either the background structure or the removable panel, pointing sideways as shown in the diagrams on
the right.
In this configuration, the panels engage horizontally and 15mm clearance is required to the side of the removable panel.
x2Ø5mm
x Ø5mm
2 x2 Ø5mm
panpanpan
15mm
to to
15mm
15mm
fallfall
tofall
Panel
Panel
Panel
head
wood
screws
engage
panel
drilling
engage
panel Laminate panels orientated vertically
drilling
head
wood
screws
head
wood
screws
engage
panel
drilling
NOTE:
Sideways
arrangements are NOT suitable
for
Compact
and over 1.2m wide.
Compact
Laminate
needs to be able to change15mm
dimensions
as ambient humidity changes.
2 x Ø5mm
15mm
2 x Ø5mm
pan pan
slideslide
to to
PanelPanel
2 x Ø5mm pan
head
wood
screws
headwood
wood
screws
head
screws
15mm slide to
engage
engage
panelpanel
engage
panel
Panel
drilling
drilling
drilling
x2Ø5mm
x Ø5mm
2 x2 Ø5mm
panpanpan
head
wood
screws
head
wood
screws
head wood screws
15mm
slide
to to
15mm
slide
15mm
slide
to
engage
panel
engage
panel
engage
panel
Panel
Panel
Panel
drilling
drilling
drilling
4. OVERHEAD & CEILING ARRANGEMENTS
Laminex does NOT consider Button-Fix suitable for ceiling or overhead installation of decorative panels.
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
REBATED FIX
Rebating the Fix creates a 3mm gap between the two panels. The Fix can be configured in three options:
1. BUTTON ON REMOVABLE PANEL
The Fix is attached to the background structure, pointing upwards as shown in the diagrams on the right.
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
Panel
Panel
Panel
drilling
drilling
drilling
x2 Ø4.5mm
2 x2 Ø4.5mm
x Ø4.5mm
countersunk
wood
screws
countersunk
countersunk
wood
wood
screws
screws
15mm
toto
15mm
fallfall
to
15mm
fall
engage
panel
engage
panel
engage
panel
2. FIX ON REMOVABLE PANEL
15mm
toto
x2 Ø4.5mm
15mm
fall
xisØ4.5mm
The
attached to the removable panel, pointing
downwards
as shown in the diagrams on the right.
15mm
fallfall
to
2 x2Fix
Ø4.5mm
countersunk
wood
screws
countersunk
wood
screws
countersunk
wood
screws
engage
panel
engage
panel
engage
panel
x2 Ø4.5mm
2 x2 Ø4.5mm
x Ø4.5mm
countersunk
wood
screws
countersunk
wood
screws
countersunk
wood
screws
15mm
toto
15mm
fallfall
to
15mm
fall
engage
panel
engage
panel
engage
panel
x2 Ø4.5mm
x Ø4.5mm
2 x2 Ø4.5mm
countersunk
wood
screws
countersunk
wood
screws
countersunk
wood
screws
15mm
toto
15mm
fall
15mm
fallfall
to
engage
panel
engage
panel
engage
panel
Panel
Panel
Panel
drilling
drilling
drilling
Panel
Panel
Panel
drilling
drilling
drilling
In this configuration, the panels engage vertically and 15mm clearance is required above the removable panel.
Panel
Panel
Panel
drilling
drilling
drilling
Panel
Panel
Panel
drilling
drilling
drilling
NOTE: REBATED FIX method is NOT suitable for Compact Laminate mounting. Compact laminate needs air flow on both
15mm
slide
x2 Ø4.5mm
2 x2 Ø4.5mm
15mm
tototo
x Ø4.5mm
15mm
slide
Panel
Panel
Panel
sides
of
the panel and room to change dimensions
byslide
~2.5%
as ambient humidity changes.
engage panel
countersunk wood screws
countersunk
wood
screws
countersunk
wood
screws
engage
panel
engage
panel
All battens behind compact laminate must be orientated vertically to allow for ventilation.
x2 Ø4.5mm
x Ø4.5mm
2 x2 Ø4.5mm
countersunk
wood
screws
countersunk
wood
screws
countersunk
wood
screws
15mm
slide
15mm
slide
15mm
slide
tototo
engage
panel
engage
panel
engage
panel
drilling
drilling
drilling
INSTRUCTIONS FOR USE – TYPE 1 FIX SETS
Panel
Panel
Panel
drilling
drilling
drilling
3. SIDEWAYS ARRANGEMENT
The Fix is attached to either the background structure or the removable panel, pointing sideways as shown in the diagrams on
the2 right.
15mm
15mm
fallfall
to
x2 Ø4.5mm
15mm
falltoto
2x xØ4.5mm
Ø4.5mm
countersunk
countersunk
wood
wood
screws
screws
countersunk
wood
screws
engage
engage
panel
panel
engage
panel
In this configuration, the panels engage horizontally and 15mm clearance is required to the side of the removable panel.
Panel
Panel
Panel
drilling
drilling
drilling
2 x2 Ø4.5mm
2x xØ4.5mm
Ø4.5mm
countersunk
countersunk
wood
wood
screws
screws
countersunk
wood
screws
15mm
slide
15mm
slide
tototo
15mm
slide
engage
panel
engage
panel
engage
panel
A USEFUL TIP
When several Button-fixes are used on a panel or if you require the panel to
be easily removable, you can reduce the strength of the click-fit.
To achieve this adapt some (but not all) the Fix mouldings by popping out
the ears with a flat screw driver, as shown in the diagram on the right. Wear
eye protection and gloves.
BUTTON DIMENSIONS
FIX DIMENSIONS
SUGGESTED JOIN DETAILS
The following diagrams offer suggestions for panel joins.
TONGUE AND GROOVE JOIN
Decorative panel
MDF, metal or HPL tongue
SEALED TONGUE AND GROOVE JOIN
Flexible Sealant
Decorative panel
MDF, Metal or HPL tongue
LAP JOIN
Decorative panel
Paint for MDF & Plywood
LAP JOIN
Screw fixing
Decorative panel
HPL or Metal reveal
CORNER DETAIL
Decorative panel
Screw fixing
HPL or Metal reveal
NOTE: Compact Laminate requires airflow on both sides of the panel and an allowance of 5mm between panels for
expansion and contraction. MDF PB requires 3mm gap between panels. All boards should be pre-conditioned on-site for
48 hours before hanging.
2/14 TLG1301
7 YEAR WARRANTY
1.
2.
3.
4.
5.
Subject to the conditions and limitations set out in this warranty below, Laminex Group Pty
Limited ABN 98 004 093 092 trading as Laminex warrants to the original purchaser of any
Laminex® Wall Panel Solutions Button-Fix™ for interior residential or commercial use who is
a “consumer” as defined in section 3 of the Australian Consumer Law that Laminex will at
its option, repair or replace any Laminex Wall Panel Solutions Button-Fix without charge if it
is defective directly as a result of its manufacture by Laminex or it’s suppliers, or the materials
used in its manufacture by Laminex or it’s suppliers, during the first seven years after the initial
purchase (proof of purchase will be required). Subject to paragraph 7, this obligation terminates
at the expiration of 7 years from the date of purchase of the product concerned from Laminex.
This warranty does not cover any defect caused by:
a)any natural occurrence or any other circumstance beyond Laminex’s control; or
b)failure to follow any procedures recommended by Laminex, at the time of
fabrication and installation, for the fabrication and installation of Laminex Wall
Panel Solutions Button-Fix; or
c)physical abuse, misuse, accidents, exposure to excessive heat, exposure to excessive
moisture, the use of solvents or inappropriate cleaning products/materials, improper
maintenance, normal ‘wear and tear’, burns, exposure to chemical products; or
d) general fading and discolouration (exposure to sunlight should be avoided); or
e)the product being used in applications that are not recommended by Laminex in the
product literature published; or
f)where the defect has been caused by faulty workmanship by any person other
than Laminex; or
g)variation in colour, pattern, shade of the material against the sample material, displays
and/or printed illustrations
The warranty also does not cover:
h) where the defect is trivial or insubstantial; or
i)where, as at the date of notification of the defect to Laminex, the defective
product no longer forms part of Laminex’s standard stock range and the person
complaining of the defect does not agree to the supply of a replacement which is
as close a type as is possible from Laminex’s then prevailing stock range; or
j)anything that has been disclosed as a feature or limitation of Laminex Wall Panel
Solutions Button-Fix in any literature published by Laminex; or
k) use of Laminex Wall Panel Solutions Button-Fix with panels other than the
recommended Laminex Decorative Panels, as the Laminex Wall Lining system has
been tested as a system incorporating appropriate Laminex Decorative Panels;
This warranty applies only to Laminex Wall Panel Solutions Button-Fix:
a)Purchased from Laminex after 1 July 1994 for interior residential or commercial
use in Australia;
b)That has remained installed at the location at which it was first installed after its
sale by Laminex;
c)Which has been installed, maintained, used and protected in the manner
recommended by Laminex, as at the relevant time of such installation, maintenance,
use or protection, in its literature published from time to time concerning Laminex
Wall Panel Solutions Button-Fix, a copy of which may be obtained, free of charge, at
the point of purchase or by writing directly to Laminex at the address given below; and
d)where Laminex has been notified of the defect within seven days of the first
person to become aware of it.
Costs of claiming:
a) Laminex will bear the expense of the reasonable labour charges which are necessary
for the repair or replacement of the Laminex Wall Panel Solutions Button-Fix Product
covered by this warranty. When submitting a claim, please provide details of the quantum
of the labour charges necessary for the repair or replacement of the Laminex Wall Panel
Solutions Button-Fix (including any quotes you have obtained verifying the labour charges).
b)If Laminex considers that you have incurred or will incur reasonable labour charges which
are necessary for the repair or replacement of the Laminex Wall Panel Solutions ButtonFix covered by this warranty, it will pay you the amount of those charges or pay those
charges directly to a third party to undertake the necessary repair or replacement works.
c)Subject to a), the person claiming the warranty will bear all other expenses of
claiming the warranty.
A replacement product may not be reasonably available from Laminex in the same shape,
type or colour as the original Laminex Wall Panel Solutions Button-Fix product covered by
this warranty. If a replacement product of the same shape, type or colour is not reasonably
available, Laminex reserves the right to provide a replacement product of as close a shape,
type and colour match as is reasonably possible from Laminex’s then prevailing product
range in satisfaction of its obligations under this warranty.
6.
Except as expressly provided in paragraphs 8 and 9, all terms, conditions, warranties,
undertakings, inducements and representations, whether express or implied, statutory or
otherwise relating in any way to Laminex Wall Panel Solutions Button-Fix are excluded.
Without limiting the generality of the preceding sentence, Laminex will not be under any
other liability in respect of any loss or damage (including consequential loss or damage)
however caused (whether by negligence or otherwise) which may be suffered or incurred or
which may arise directly or indirectly in respect of Laminex Wall Panel Solutions Button-Fix.
7. Where any applicable legislation implies any term, condition or warranty into the contract
of sale between Laminex and a person, or Laminex’s relationship with a person, which
has acquired Laminex Wall Panel Solutions Button-Fix, or otherwise gives that person a
particular remedy against Laminex, and that legislation or any legislation voids or prohibits
any provision excluding, or modifying the application of, or exercise of, any liability
under such term, condition, warranty or remedy, then that term, condition warranty or
remedy shall be deemed to be included in or, as the case may be, apply to that contract
or relationship. However, Laminex’s liability for any breach of such term, condition or
warranty or under such remedy, shall be limited, at Laminex’s option, in any one or more
of the ways permitted by that legislation including, where so permitted:
a) If the breach related to Laminex Wall Panel Solutions Button-Fix:
i. The replacement of Laminex Wall Panel Solutions Button-Fix or the supply of
equivalent product;
ii. The repair of Laminex Wall Panel Solutions Button-Fix;
iii.The payment of the cost of replacing Laminex Wall Panel Solutions Button-Fix or
acquiring equivalent product; or
iv. The payment of the cost of having Laminex Wall Panel Solutions Button-Fix
repaired; and
b) If the breach relates to services:
i. The supplying of the services again; or
ii. The payment of the cost of having the services supplied again.
8. Please note that the benefits given by this warranty are in addition to other rights and
remedies of the person under a law in relation to the goods or services to which this
warranty relates. This warranty should not therefore be read as an exclusive statement
of the rights of the original purchaser or any other person.
9. Our goods come with guarantees that cannot be excluded under the Australian
Consumer Law. You are entitled to a replacement or refund for a major failure and
compensation for any other reasonably foreseeable loss or damage. You are also
entitled to have the goods repaired or replaced if the goods fail to be of acceptable
quality and the failure does not amount to a major failure.
10. This warranty does not cover any other product used or installed in connection with
Laminex Wall Panel Solutions Button-Fix.
11. This warranty is not transferable or assignable.
12. Any inquiries regarding this warranty should be sent to Laminex Wall Panel Solutions
Button-Fix Warranties, Laminex, P.O. Box 407, Doncaster, VIC 3108. Inquiries can also be
made by calling 132 136 or emailing enquiries@laminex.com.au.
13. To claim this warranty, please send the following written details to the address set out above:
•Your name, address and telephone number
•Place where the Laminex Wall Panel Solutions Button-Fix Product was purchased
and amount you paid for it. Please also provide a copy of your proof of purchase
•If the Laminex Wall Panel Solutions Button-Fix Product has been installed - the
address at which it was installed, the date of installation, the name of the person
and company that installed it, the quantum of the labour charges necessary for
the repair or replacement of the Laminex Wall Panel Solutions Button-Fix Product
(including any quotes you have obtained verifying the labour charges)
•Description of how the Laminex Wall Panel Solutions Button-Fix Product is
defective and when you found out that it was defective. Please also provide any
photographs taken of the defect(s)
After we receive your written claim, we will contact you to discuss. In some
circumstances Laminex may need to remove a sample of the installed Laminex Wall Panel
Solutions Button-Fix Product for testing.
For more information visit laminex.com.au or call 132 136.
Laminex Wall Panel Solutions Button-Fix is marketed and distributed by Laminex ABN 98 004 093 092. The colours of the products featured within the imagery in this brochure are as close
to the Laminex Wall Panel Solutions Button-Fix range as photographic lighting and modern printing processes allow. Laminex®, Button-Fix™