INSTALLATION – ASSEMBLY INSTRUCTIONS
HEWLETT PACKARD HP450, 460, 470 & CANON IP 100
PRINTER / ARM REST MOUNTS
Models – C-PM-103, C-PM-107
C-ARPB-104, 105, 106, 107, 108, 109, 111 and 112
TOOLS REQUIRED:
Phillips Screwdriver
¼ Drive Ratchet wrench
Socket Set
PARTS and MOUNTING HARDWARE:
QTY
DESCRIPTION
PART #
1
12
4
4
4
HP or Canon Printer mount bracket assembly
Rubber Bumper
¼ x ¾ Carriage Bolt (Bracket to Armrest)
¼ Serrated Hex Nut
¼ Flat Washer
C-PM-103 or 107
GSM19802
GSM32000
GSM30023
GSM31005
1
4
4
4
Arm Rest and bracket assembly
C-ARM-103, 104 or 105
(Hardware for Bracket to Console or Tunnel Mount Extrusion)
¼ x ½ PPHMS
GSM33123
¼ Nut
GSM30005
¼ Flat Washer
GSM31005
1
1
4
4
4
1
2
2
2
2
4
Flip Up bracket assembly (for arm pad)
Hinge
¼ x ½ PPHMS (Hinge Screws)
¼ Lock Nut
¼ Flat Washer
Latch assembly (Catch and Keeper)
8/32 x 3/8 PPTHMS (Catch to CM002564 plate)
8/32 Nuts
6/32 x ½ PPHMS (Keeper to printer side bracket)
6/32 Nuts
¼ x ¾ PPHMS (Arm Pad screws)
CM002564
CM86132
GSM33123
GSM30016-1
GSM31005
GSM50252
GSM33540
GSM30027
GSM33105
GSM30034
GSM33124
Always!
 Read all instructions before installing any Havis Inc. products.
 Use only hardware provided with install kit.
 For product support, email technicalsupport@havis.com or call 1-800-524-9900.
C-ARPB-104_INST_7-14
C-ARPB-XXX
ASSEMBLY DRAWING
Arm Pad from C-ARM-XXX
CM002564
¼ Hinge Lock Nuts
Catch
8/32 x 3/8 screws
Hinge
Arm Pad ¼ x ¾ Bolts
(Reused from original
arm rest mount)
10/32 x ½ screws and
nuts also attach side hinge
bracket for added strength
Keeper
6/32 x ½ screws and nuts
¼ x ½ Side Bracket
Bolts and washers
(2) each side
C-PM-107 (shown)
¼ x ¾ Carriage Bolts & nuts (not shown)
For attaching printer bracket to flip up
arm rest bracket or other flat surface.
¼ x ½ Hinge Bolts
C-ARPB-111 & 112
does not have a CARM Bracket
C-ARM-103
C-ARM-104
C-ARM-105
C-ARPB-104_INST_7-14
Attach rubber bumpers (supplied) to metal parts to protect plastic printer housing
Left Side Clamp Bracket (bumpers)
Right Side Clamp Bracket (bumpers)
Side clamp brackets for the HP printer mount shown
Attach Right Side Clamp Bracket to base
plate assembly with ¼” x ½” Round Head
Bolts. Also attach to back arm with # 10
nuts and bolts. Place printer into base plate
assembly. (shown without arm pad)
Attach Left Side Clamp Bracket to base plate
assembly with ¼” x ½” Round Head Bolts.
Note: Printer is installed after base
assembly is bolted to other optional bracket.
C-ARPB-104_INST_7-14
Assembly / Installation Notes:
1. The parts for the various Printer mount configurations are shipped as three (3) primary (separate)
components and do require further sub-assembly.
2. The Arm Pad must be removed from the standard arm rest bracket and remounted onto the CM002564
plate. Reuse ¼ x ¾ bolts. The Hinge and latch must also be assembled to the CM002564. (See above
diagram)
3. Rubber bumpers provided should be placed so only the rubber pads touch the plastic printer housing.
(See above photos)
4. Bolt printer bracket assembly to the flip up arm rest bracket with ¼ x ¾ carriage bolts, washers and
nuts.
5. Bolt the complete Arm Rest Printer Mount assembly to the console sides or flat surface as desired with
¼ x ½ bolts, nuts and flat washers.
6. The examples below show some completely assembled mounts.
7. If needed, the arm pad hinge tension can be adjusted with the tension adjustment screw located on the
arm rest side of the hinge.
C-ARPB-104
C-ARPB-107
Console mount for HP-450,460 & 470 printers
Console mount for Canon IP-100 Printer
C-ARPB-108
C-ARPB-109
Platform mount for Canon IP-100 Printer
Side mount for Canon IP-100 Printer
C-ARPB-104_INST_7-14