BC-Series
Schematics
3
Founded in 1987, Buzon Pedestal
first European manufacturer of the
“Buzon” (screw jack) Pedestal which is
The support head (1) is screwed directly into the base or
the coupler.
1
International (B.P.I. s.a.) is the
Both the head and the coupler have a safety stop (2)
located at the base of the threads that prevents overextension.
2
On the support head there are, 16 holes (3) which
allow you to attach the tabs in various combinations to
accomodate a myriad of patterns. (see diagram right)
adjustable millimetre by millimetre up
to 1030mm. Made from polypropylene
and able to bear loads of more than
5
1000 kg/pedestal for the support of
4
paving slabs and timber or timber
composite decking on roof terraces,
The 4mm thick, 200mm diameter polypropylene base (6)
can be placed or fixed on a solid substrate.
balconies, garden terraces and around
swimming pools. Also used for
The coupler (4) is used when the height of the pedestal
exceeds 200mm. Two stabilizing brackets (5) allow the
pedestals to be tied to each other with wire, ensuring
greater stability when the height exceeds 600mm.
Holes (7) at the bottom of the base are incorporated into
its design to allow drainage and prevent the collection of
stagnant water.
2
temporary floors in trade shows, special
events and raised floors in many other
industrial applications.
6
A single BC-PH5 slope corrector (8) can compensate for
a horizontal slope from 0 to 5%. This is placed under the
base of the pedestal.
7
8
BC-PH5 Slope Corrector
0%
90°
A slope corrector placed under the base of the pedestal
will compensate for a slope of up to 5 % in the substrate.
2
0%
5%
Slope correction from 0 to 5% with BC-PH5 under the BC-Series
Components:
Slope corrector
Bubble level
Circular Tabs
5
4
3
Base + Head
2-12
5
4
3
2
1
5
4
3
2
1
5
4
3
3
3
4
4
5
2
1
= 3%
EXAMPLE:
5
4
3
Bubble
indicates % and
the direction of the slope
2
1
5
5
4
3
0
0
2
5
4
3
1
Place the bubble level on the ground
2
1
1
2
5
4
3
1
Use of BC-PH5 slope
corrector on a
pitched roof
2
1
BC-PH5
2
1
2
1
Slope from 0 to 5 %
3%
Slope corrector BC-PH5
3%
2
Adjustment of the slope corrector for 3%
Place the corrector on the ground in
the direction of the slope
3
Upper disc
3
4
Lower disc
2
1
0
0
5
1
4
3
2
5
5
5
4
4
3
3
2
1
0
1
0
3%
3
3
2
Direction of the slope
3%
4
Place the pedestal on the slope
corrector set at 3%
5
Position of the pedestal under the tile
and adjust height
3%
3
Direction of the slope
3%
9
Assembly of the BC-2 and BC-3 with or without the BC-PH5 Slope Corrector 0 to 5%
Components:
BC-2
BC-PH5 Slope Corrector
2 to 12
Circular Tabs
BC-3
BC-2 height adjustment from 41 to 55mm
55mm
41mm
BC-2
BC-3 height adjustment from 55 to 85mm
85mm
55mm
BC-3
BC-2 and BC-3 with Slope Corrector 0 to 5 % - BC-PH5
With circular tabs
BC-2
or BC-3
BC-PH5 0 to 5%
10