Luminite Genesis product range
Wireless PIR detectors
G1 Wireless PIR’s 30m x 20m
G1 Wireless PIR’s 15m x 20m
G1 Wireless PIR’s 40m x 4.5m
G1 Wireless PIR’s 12m Horizontal curtain
G1 Wireless PIR’s 12m Vertical curtain
LGWP3020
LGWP1520
LGWP4004
LGWP12HC
LGWP12VC
G2 Wireless PIR’s
G2 Wireless PIR’s
LG2WP3020
LG2WP6004
30m x 20m
60m x 4m
Wireless Accessories
IP Masthead/Repeater
Masthead/Repeater
Masthead Relay Unit
Relay Expansion Module
Walk Test Instrument
16 way relay unit
Relay module
16 way DM interface unit
16 way relay unit with end of line resistor
Relay module with end of line resistor
Optional antenna
Transmitter module
LGIP MT434
LGMT434
LGMRU4x4
LGREM4x4
LGWT434
LGRU16
LGRM8
LGDM16
LGRU16ELR 3 versions
LGRM8ELR 3 versions
AE434
LGTX434
Hard wired PIR detectors
G1 Wired PIR’s
30m x 20m
G1 Wired PIR
15m x 20m
G1 Wired PIR
40m x 4.5m
G1 Wired PIR
12m horizontal curtain
G1 Wired PIR
12m vertical curtain
LGHW3020
LGHW1520
LGHW4004
LGHW12HC
LGHW12VC
G2 Wired PIR’s
G2 Wired PIR’s
LG2HW3020
LG2HW6004
30m x 20m
60m x 4m
Plug on wireless transmitter module
Hard Wired
PIR Detector
Installation
Handbook
LG2TM434
Type: LG2 HW-3020 & HW-6004
2a BELLEVUE ROAD, FRIERN BARNET, LONDON, N11 3ER
Tel: 0044 (0) 208 368 7887 Fax: 0044 (0) 208 368 3952
LUMINITE ELECTRONICS LTD, 2a BELLEVUE ROAD, FRIERN BARNET, LONDON, N11 3ER
Tel: 0044 (0) 208 368 7887 Fax: 0044 (0) 208 368 3952
Web: www.luminite.co.uk email: sales@luminite.co.uk
V2 Issue 2
PRE-INSTALLATION NOTES
Detection Patterns.
Unpacking.
On receipt, inspect the package and contents for signs of damage. If damage
has occurred, advise the carrier and/or suppliers immediately. Inspect the
contents to confirm that all items are present and undamaged. If any items are
missing or damaged, contact the supplier immediately. It is advisable that the
original carton is retained as this forms the safest transport container in the
event that a unit has to be returned for any reason.
There are two
mirror versions to
choose from but the
mirrors are not
interchangeable.
Servicing.
This unit should not require general servicing. Any repair work should only be
undertaken by qualified service personnel.
Moisture.
Do not expose the internal electronics of this unit to moisture i.e. take care
during installation or when changing batteries not to allow rain or damp into the
product. When the product is sealed it is water resistant to IP66.
Take great care of the mirror surface. Do not scratch it or allow dust or dirt to
settle on it.
Model LGWP3020
Type 7
Box Contents.
1 x GENESIS hard wired G2 series PIR detector
1 x Rear tamper ring magnet
3 x no 8 wall plugs
3 x no 8 2” screws
1 x no 6 1/2” screw
1 x no 6 wall plug
LG2HW-3020 & 6004 hard wired PIR Detector Specification.
Mirror type
Temp comp
Power supply
IP rating
Enclosure
Colour
Temperature
30 metre x 20 metre or 60 metre x 4 metre.
Detection / Anti Tamper / Anti Cloaking / Shock.
Temperature sensor compensates for extreme conditions
12-24 volts AC or DC
66
High impact ABS with EPDM 1mm thick window
Silver
-10 +70c
LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook
Page 2.
Model LGWP6004 Type 6
Detection range will vary according to the air temperature and surrounding
environment.
For example: large areas of white concrete in very hot weather will reduce the
sensitivity as will air temperatures of 37 degrees. If these situations occur and
are present every day then it may be necessary to increase the sensitivity of the
detector by following the instructions on page 11. 0 is the standard setting but
can be increased in increments of +1 up to +5.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 15.
Testing & Commissioning.
INDEX
Adjust the mirror to the desired direction of detection .
If you have an LG2TM434 test module, fit it now.
Switch on the power and observe the momentary HI message on the
display.
Program the setting as required. Pages 10 & 11.
If you are using the LGWT434 Walk Test Instrument, set ES to 0
It is recommended to set AND/OR to 1 and Pulse Count to at least 2. This will
improve stability in environments where there is a lot of incidental movement
from foliage and loose material.
Fit the front cover to prevent air flow around the sensor during testing.
DO NOT PUSH THE WHITE WINDOW.
It is not necessary to secure the screw but be aware that the tamper will remain
during testing until the screw is fitted.
Using the LGWT434 Walk Test Instrument walk within the detection area,
stopping and waiting for about five seconds each time detection occurs.
The instrument will display D each time detection occurs.
Lens type will display as Type 6 for the 6004 or Type 7 for the 3020.
page
Introduction.
4&5
Types of tamper.
5
Installation.
6
Mounting height and positioning.
Minimising false alarms.
7
Wiring the detector.
8
Mirror adjustments.
9
Programming.
10
Mode options and Settings.
11, 12 & 13
Walk test transmitter
13
Testing and commissioning.
14
Detection patterns.
15
See the operating instructions for the walk tester for more information.
Adjust the mirror as described on page 9 and re-test until optimum coverage is
achieved.
Once you are happy that the detector is operating to your requirements, remove
the LG2TM434 module and screw the cover screw up from the bottom being
careful not to cross thread it. It is good practice to switch the power off before
removing the module but not essential.
NB: Because the cover has a liquid tight gasket seal there will be an air
pressure build up inside the product which will gradually normalise. The side
effect of this will be to cause the sides around the gasket to lift slightly. Using
the palms of your hands, gently push the sides in and towards the wall which will
close up the gap. Be careful not to push the white window as damage will
occur.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 14.
Copyright 2015 Luminite Electronics Ltd
All rights reserved. Unauthorised duplication of this handbook by any means
LG2 WP-3020 & WP-6004 Wireless PIR Detector Installation Handbook
Page 3.
Introduction
The LG2HW3020 & LG2HW6004 hard wired Passive Infra Red Detectors (PIR)
have been designed to meet the newest and most demanding requirements of
the CCTV market. These new, stylish detectors are available in two different
detection patterns and use superior Black Mirror Technology to provide excellent
detection with minimal false alarms.
The two ranges are:
30 metres out x 20 metres across or
60 metres out x 4 metres across.
ENCLOSURE.
LG2 detectors have a modern styling which disguises the product’s true function
and helps them to blend in with modern architecturally designed buildings. The
front window is made of pigmented HDPE which hides the mirror and the main
body of the enclosure is ABS with a high quality paint finish. Both parts are UV
stabilized and the weather proof rating is IP66.
BLACK MIRROR TECHNOLOGY.
These new PIR’s use mirror technology instead of Fresnel lenses. The large
mirror provides significantly more optical gain which allows a thick EPDM front
filtered window to be used without the need to increase sensitivity.
White light from car headlights can cause false alarms, so it is important to filter
out this interference. Most PIR detectors use pigmented windows or Fresnel
lenses and sometimes an extra silicon filter to reduce white light, but this has the
effect of also reducing the infrared energy and consequently detection range.
The Black Mirror acts as a selective optical filter for body heat infrared with
minimal loss while filtering out unwanted white light by as much as 14000 LUX.
The combination of high optical gain and white light filtering means that the
electronic sensitivity is much lower and therefore the risk of false alarms from
electrical interference and component noise is greatly reduced.
The other problem of running amplifiers at extremely high gain is that they reach
saturation which obscures any signature that the micro controller would use to
accurately determine the validity of a detection.
The Luminite LG2 amplifier runs at a relatively low level and with the
combination of the adaptive focal length optically sharp edges of each mirror
segment together with the sophisticated detection algorithm has the result of
accurate detection at various speeds and distances.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 4.
This module may also be left permanently fitted to enable wireless operation of
a range of wireless receivers of both Genesis and Easyswitch types.
The Easyswitch mode (option 1) changes the default Genesis transmission
protocol to Easyswitch.
Easyswitch is a range of wireless switching products and can be used to control
lighting, sounders etc.
There will soon be a new 16 way receiver (ESR16) which has relay alarm
contacts and can be connected to other alarm equipment.
For the latest updates and models see (Easyswitch products on our web site).
Timer mode.
This mode is for use with the Easyswitch option and tells the receiver how long
to change the contact state for.
It is adjustable from 0 to 127. These numbers do not translate to seconds and
are different for each type of receiver.
A conversion table is available on request.
LG2TM module:
It is good practice but not essential to turn off the power before fitting this
module.
Make sure that the module is orientated correctly and carefully plug it onto the
pins on the right hand side of the top board. Now re apply the power and
observe the HI on the display.
By default this module will transmit Site code 32, Sub net 1 and Unit number 1.
These settings cannot be changed. Use the Genesis LGWT434 walk test
instrument to test the field of view.
LG2TX
M
TRAN1
434
Plug LG2TM434
module onto these pins.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 13.
Sensitivity.
The normal setting is 0. Low sensitivity is sometimes needed to reduce the
detection distance.
Higher sensitivity increases distance but also increases the risk of false
activation from environmental conditions.
AND / OR.
The Genesis 2 PIR detector uses a Quad in line pyro sensor which
acts like two separate sensors side by side.
The AND / OR mode can select whether both sensors must detect movement
together or whether only one or the other is required.
AND gating is the best for filtering out nuisance alarms from loose
materials, foliage and reflections.
OR gating is more sensitive and may be selected when fast moving objects are
to be detected.
Power saving.
Busy sites such as school playgrounds, car park entrances etc can cause an
unnecessarily large number of alarm events during busy times.
It is still possible to reduce them by invoking power saving mode.
There are four types of power saving which may be selected to suit.
1.
2.
3.
4.
An alarm can only be sent after 3 minutes of inactivity
An alarm can only be sent after 10 minutes of inactivity
An alarm can only be sent after 30 minutes of inactivity
The same as 3 but with an accumulative timer which can extend the 30
minutes if the site remains very busy.
In addition the sleep timer does not initiate after the first alarm but instead
after a build up of activity.
The next two options are for the LG2TM434 transmitter module.
Easyswitch PIR mode.
In the Genesis mode (option 0) this detector will behave like the Genesis 2
wireless version and can be used with the LGWT434 Walk Test Transmitter.
After testing the transmitter can be removed and used to test other detectors.
Alternatively leave the transmitter permanently fitted to facilitate both wireless
and hard wired operation.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 12.
ADAPTIVE FOCAL LENGTH.
The mirrors have adaptive focal length which regulates the image size for
varying distances which helps regulate detection when the target is moving at
faster or slower speeds regardless of distance from the detector.
AND OR.
The Quad in line pyro sensor splits each detection zone into two which are then
labelled A and B. The G2 detector can be configured to go into alarm with either
(A AND B) or (A OR B). AND detection is the best way to minimise false alarms
as it filters out spurious movements from loose materials and foliage.
SHOCK and CLOAK.
The G2 PIR also contains a shock sensor to detect physical attack and IR
transmission anti-masking. On the hard wired version, these alerts activate the
anti masking relay but only momentarily.
EXTERNAL POWER.
The G2 detector is powered from an external supply (not supplied) which must
be between 12-24 volts AC or DC and at least 200m/a.
TYPES OF TAMPER:
Front cover micro switch.
Activated when the cover screw is removed.
Rear tamper Hall effect and magnet.
The magnet is fixed to the wall and when the product is removed the magnet is
left behind.
Shock sensor.
Piezo sensor on mother board detects physical attack to the product.
Anti masking.
Active IR and LDR sense when the front window is obscured. These sensors
always face the same direction as the mirror.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 5.
Installation:
First, the front cover must be removed by unscrewing the bottom screw and
lifting the cover just past the top of the gasket. Push the whole cover
upwards so that it slides out off the retaining claws. (See diagram supplied in
the carton).
To fix the product to the wall and connect to the terminals, it is easier to remove
the mirror assembly (recommended).
Mirror removal procedure.
Detach the mirror assembly by
removing the white knurled nut
and the R clip.
6 way plug
Pull out the bottom spindle
followed by the top threaded
spindle. Unplug the 6 way
Plug from the mother board and
carefully place the assembly to
one side ensuring that it does not
Front cover claw sockets
get wet or contaminated. The
mirror must remain perfectly clean
and scratch free.
External power
Knurled nut
Screw hole
& bung
input
Using the drill template
provided, drill and plug the holes
using the supplied wall plugs.
Screw the rear tamper magnet in
the centre using the No4 screw
and yellow plug.
Cable glands
6 way socket
Place the product over the
magnet so that it resides in the
rear recess and then screw the
product in place using the three
No8 screws provided.
Re-fit the black hole bungs
provided to maintain the weather
rating.
Screw holes
& bungs
Front cover screw insert
MODE OPTIONS:
SETTINGS:
IA
It
AL
PL
SE
An
PS
ES
tI
0 = (N/O) 1 = (N/C)
0 = (N/O) 1 = (N/C)
1 to 20 seconds
1 to 4
-5..0..+5 -5 Lowest, 0 Normal, +5 Highest
0 = OR 1 = AND
0-OFF, 1 to 4 ON (Four modes)
0 = Genesis 1 = Easyswitch
0...127
Idle alarm relay state
Idle tamper relay state
Activity length (contacts)
Pulse counting
Sensitivity
AND/OR gating
Power saving
Easyswitch PIR mode
Time adjust
Idle alarm relay state.
Changes alarm relay contacts from
normally open (NO) to normally closed (N/C)
Idle tamper relay state.
Changes tamper relay contacts from
normally open (NO) to normally closed (N/C)
Activity length.
Relay contact state change duration. 1 to 20 seconds. Default is 1 second
Pulse counting.
Counts the number of pulses caused when a person walks across the detector’s
field of view. The greater the number, the more the person has to move to
cause an alarm. Pulse count 1 is very sensitive while pulse count 4 is quite
insensitive. Experiment with the setting to optimise the results so that
persons are detected in good time but not so sensitive that the detector may be
prone to false alarm from incidental movement from trees, shrubs, loose
materials etc.
20mm Cable entry
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 6.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 11.
PROGRAMMING:
The new version 2 model now has an
LED display and push buttons to set
the mode of operation.
This makes changing settings much
easier as the buttons and display are
easily located on the top of the mirror.
Button functions.
SELECT
M MEMORISE
Mounting height and positioning:
Mounting height
TRAN1
M
2.5m
To
4m
UP
DOWN
Power On,
When the power is turned on, the display shows
Mounting height
The correct height for the PIR is 2.5 metres above
the ground, however it can be mounted up to 4
metres but the mirror must be angled down.
See “mirror adjustments”.
momentarily.
How to set standard functions.
Step 1. Enter the settings mode. Press M until the display shows
IMPORTANT:
Make sure that the rear tamper magnet has been fitted first using the template before fixing the product in place.
Step 2. Scroll through the mode options with this button
Minimising false alarms:
Make sure that nothing can move or flutter in front of the detector and avoid
facing reflective surfaces. The fixing of the detector must be solid and not
sway. Avoid situations where the detector can overshoot the detection area.
The Genesis 2 detector uses a patented Black Mirror which filters out unwanted
sunlight however it is still good practice to consider the position carefully to
minimise the possibility of reflections.
EG:
When the desired mode is reached, wait a moment and then the display will
flash the setting. EG:
= pulse count 1.
To change a setting, select the mode and wait for the setting to flash.
Scroll up or down to the desired number.
Step 3. Press and hold the M button to store the new number.
The display shows
6 way socket
followed by
Now let go of the button and the new setting is now stored.
EXAMPLE: M
M
To change more than one setting at a time, follow steps 1 and 2 and after
changing the setting press
to select the next mode. Press the M button
when all changes have been made.
NB: The display will automatically turn off after 10 minutes if M is not pressed.
20mm Cable entry
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 10.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 7.
Wiring the detector:
There are two IP66 rubber grommets at the rear of the detector which enable a
4-6mm diameter cable to be passed in and out of the product.
There is also an alternative cable entrance at the bottom of the detector which is
a knockout for a 20mm cable gland.
Rear view showing the
grommets and cable
channel.
Mirror adjustments:
If the mirror assembly was removed, re-fit it now.
Horizontal Left / Right adjustment is achieved by slackening the knurled white
thumb screw and rotating the mirror assembly click by click in 10 degree steps to
the required position. The degrees –90 0 +90 are shown in the picture.
Fine adjustment from –5 to +5 degrees is achieved by rotating the Fine Adjust
screw either clockwise or anti-clockwise.
Top view
Horizontal
Coarse Adjust
–90 +90 degrees
Remove slide cover and knock out
20mm hole if using a cable gland.
Power supply.
This product has a special regulator which allows it to be powered from a variety
of voltages ranging from 12 volts to 24 volts and they may be AC or DC.
Once the power is connected the product will begin to operate.
Allow two minutes for the circuit to settle before beginning walk testing.
Alarm & Tamper.
Both the alarm and tamper relays provide Volt Free contacts which can be
configured to be N/O or N/C
The contact duration is selectable from 1 to 10 seconds
(see programming on page 10).
Vertical Up / Down adjustment is achieved by adjusting the white plastic screw
as shown.
Horizontal Fine Adjust.
ALARM
TAMPER
12-24V
AC or DC
Vertical Adjust
Mirror tilt.
+ 5 deg
0 deg
-5 deg
-10 deg
-15 deg
Walk Test Transmitter.
A plug on test transmitter (LG2TM434) can be fitted to facilitate the test
procedure.
(See Testing and Commissioning on page 14).
The transmitter can also be permanently fitted to provide a wireless link to
Genesis or Easyswitch receivers. (See page 13)
Aim the mirror in the direction you wish to protect and tighten the horizontal
coarse adjust screw.
It is not normally required that the mirror be tilted up or down and it should be
left in the neutral 0 deg position.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 8.
LG2 HW-3020 & HW-6004 Hard Wired PIR Detector Installation Handbook
Page 9.