Resistance Temperature Detectors
Process connection:
Magnet, metal contact
block, washer, weld-on
sheet or worm drive hose
clamp
Sensor Element:
Pt100, Pt1000, Pt10,
Cu10, or Ni120
Measuring range:
-200 °C to +1000 °C
(depending upon element)
Wiring configuration:
2, 3, or 4 wire
(single or dual)
„„ Class B to DIN
EN 60751
„„ Class A to DIN
EN 60751
„„ Less than class B
Electrical approvals:
CSA, FM, ATEX/IEC
„„ Lengths and
diameters standard
or customer specific
„„ Transmitter mounted
directly within
connection head
„„ Calibration - single
point, multiple points,
and to Callendar-Van
Dusen coefficients
Options:
WIKA worldwide
Features:
TR50 - Surface RTD Sensor
Classification tolerance:
Electrical
Temperature
Measurement
„„ Material traceability
of the conductors,
metal sheath and
mineral insulation
„„ Selectable accuracy
tolerance
„„ Special designs
„„ The assembly can be supplied with or without a
transmitter. Transmitters convert the resistance
signal from the RTD to a linear analogue or
digital output (commonly 4-20 mA). This signal
reduces potential inaccuracies by negating the
need for compensating output lead wires.
„„ The assembly has electrical approvals for
explosion proof hazardous locations, ingress
protection and general purpose areas.
„„ Electrical authorities that have registered these
approvals include CSA, FM, and ATEX/IEC.
Note: CSA and FM approvals apply only when
configured with a certified connection head
together with flexible armour and cord grip.
„„ Sheath materials available include stainless
steels, corrosion resistant and high temperature
oxidation resistant alloys. For temperatures
greater than 600°C it is advisable to utilize an
Inconel 600 sheath in place of stainless steel.
„„ RTD diameters are 0.125, 0.188 inch
or 0.250 also 3 or 6 mm.
„„ RTD temperature ranges are dependent on
the RTD element, sheath material, element
accuracy and the process attachment.
„„ Terminations include stripped leads, 3-pin plugs,
Tegam/Keithley plugs, spade lugs, Lemosa plugs
or connection head complete with cord grip.
„„ Termination accessories include cord
grip, cable or wire clamps, and braze,
crimp or compression adapters.
„„ If required the metal sheath can be formed
during manufacture or by the installer.
„„ Extension cable is available in a variety of
insulation and jacket materials. These include
interlocking flexible armour, braided stainless
steel, fibreglass, PTFE (Teflon®), PVC, and Silicon.
North America
Africa/Middle East
Canada
WIKA Instruments Canada Ltd.
Edmonton, Alberta
Tel.: (+1) 780 463 7035
Fax: (+1) 780 462 0017
E-mail: info@wika.ca
www.wika.ca
Benelux
WIKA Benelux
Echt
Tel.: (+31) 475 53 55 00
Fax: (+31) 475 53 54 46
E-mail: info@wika.nl
www.wika.nl
Romania
WIKA Instruments Romania S.R.L.
Bucuresti
Tel.: (+40) 21-456 31 38
Fax: (+40) 21-456 31 37
E-mail: m.anghel@wika.ro
www.wika.ro
Egypt
WIKA Alexander Wiegand
GmbH & Co. KG
Nasr City, Cairo
Tel.: (+20) 2-227 33 140
Fax: (+20) 2-227 33 140
E-mail: Ahmed.Azab@wika.de
Kazakhstan
TOO WIKA Kasachstan
Almaty
Tel.: (+7) 3272 33 08 48
Fax: (+7) 3272 78 99 05
E-mail: info@wika.kz
www.wika.kz
Mexico
Instrumentos WIKA México,
S.A. de C.V.
Álvaro Obregón
Tel.: (+52) 55 5020 5300
Fax: (+52) 55 5020 5301
E-mail: ventas@wika.com
www.wika.com.mx
Bulgaria
WIKA Bulgaria EOOD
Sofia
Tel.: (+359) 2 82138-10
Fax: (+359) 2 82138-13
E-mail: t.antonov@wika.bg
www.wika.bg
Russia
ZAO “WIKA MERA”
Moskau
Tel.: (+7) 495-648 01 80
Fax: (+7) 495-648 01 81
E-mail: info@wika.ru
www.wika.ru
Korea
WIKA Korea Ltd.
Seoul
Tel.: (+82) 2-869 05 05
Fax: (+82) 2-869 05 25
E-mail: info@wika.co.kr
www.wika.co.kr
Finland
WIKA Finland Oy
Helsinki
Tel.: (+358) 9-682 49 20
Fax: (+358) 9-682 49 270
E-mail: info@wika.fi
www.wika.fi
Serbia
WIKA Merna Tehnika d.o.o.
Beograd
Tel.: (+381) 11 2763 722
Fax: (+381) 11-753 674
E-mail: info@wika.co.yu
www.wika.co.yu
Iran
WIKA Instrumentation Pars
Kish Ltd.
Tehran
Tel.: (+98) 21- 8852 6730 3
Fax: (+98) 21- 8875 7413
E-mail: info@wika.ir
www.wika.ir
France
WIKA Instruments s.a.r.l.
Eragny-sur-Oise
Tel.: (+33) 1/34 30 84 84
Fax: (+33) 1/34 30 84 94
E-mail: info@wika.fr
www.wika.fr
Spain
Instrumentos WIKA, S.A.
Sabadell (Barcelona)
Tel.: (+34) 902 902 577
Fax: (+34) 933 938 666
E-mail: info@wika.es
www.wika.es
Germany - Head Office
WIKA Alexander Wiegand
GmbH & Co. KG
Klingenberg
Tel.: (+49) 9372 132-0
Fax: (+49) 9372 132-406
E-mail: info@wika.de
www.wika.de
Switzerland
MANOMETER AG
Hitzkirch
Tel.: (+41) 41 919 72 72
Fax: (+41) 41 919 72 73
E-mail: info@manometer.ch
www.manometer.ch
USA
WIKA Instrument Corporation
Lawrenceville, Georgia
Tel.: (+1) 770-513 8200
Fax: (+1) 770-338 5118
E-mail: info@wika.com
www.wika.com
South America
Argentina
WIKA Argentina S.A.
Buenos Aires
Tel.: (+54) 11 4730-1800
Fax: (+54) 11 4761-0050
E-mail: info@wika.com.ar
www.wika.com.ar
Brazil
WIKA DO BRASIL
Iperó - SP
Tel.: (+55) 15 3459 9700
Fax: (+55) 15 3266 1650
E-mail: marketing@wika.com.br
www.wika.com.br
Europe
Austria
WIKA Meßgerätevertrieb
Ursula Wiegand GmbH & Co. KG
Wien
Tel.: (+43) 1-8 69 16 31
Fax: (+43) 1-8 69 16 34
E-mail: info@wika.at
www.wika.at
**,"6
„„ Explosion protection:
CSA, FM (class I
division II / class
I zone II)
„„ Intrinsically safe
version: ATEX (EEx-i)
„„ Non-sparking version:
ATEX (EEx-n)
„„ RTD transmitter
matching
103-02017 11/2007 CA
Italy
WIKA Italiana SRL
Arese (Milano)
Tel.: (+39) 02-93 86 11
Fax: (+39) 02-93 86 174
E-mail: info@wika.it
www.wika.it
Poland
Kujawska Fabryka Manometrow
Wloclawek
Tel.: (+48) 54230 11 00
Fax: (+48) 54230 11 01
E-mail: info@manometry.com.pl
www.manometry.com.pl
Ukraine
WIKA Pribor GmbH
Donetsk
Tel.: (+38) 062 345-34-16
Fax: (+38) 062 345-34-17
E-mail: info@wika.donetsk.ua
www.wika.donetsk.ua
United Kingdom
WIKA Instruments Limited
Merstham, Redhill
Tel.: (+44) (0) 1737 644 008
Fax: (+44) (0) 1737 644 403
E-mail: info@wika.co.uk
www.wika.co.uk
South Africa
WIKA Instruments (Pty.) Ltd.
Gardenview, Johannesburg
Tel.: (+27) 11-621 00 00
Fax: (+27) 11-621 00 59
E-mail: sales@wika.co.za
www.wika.co.za
United Arab Emirates
WIKA Middle East FZE
Jebel Ali, Dubai
Tel.: (+971) 4-883 90 90
Fax: (+971) 4-883 91 98
E-mail: wikame@emirates.net.ae
Asia
China
WIKA International Trading
(Shanghai) Co., Ltd.
Shanghai
Tel.: (+86) 21 53 85 25 72
Fax: (+86) 21 53 85 25 75
E-mail: wikash@online.sh.cn
India
WIKA Instruments India Pvt. Ltd.
Wagholi, Pune
Tel.: (+91) 20-66293200
Fax: (+91) 20-66293325
E-mail: sales@wika.co.in
www.wika.co.in
Japan
WIKA Japan K.K.
Minato-ku, Tokyo
Tel.: (+81) 3-5439-6673
Fax: (+81) 3-5439-6674
E-mail: t-shimane@wika.co.jp
Malaysia
WIKA Instrumentation (M) Sdn Bhd
Puchong, Selangor
Tel.: (+03) 80631080
Fax: (+03) 80631070
E-mail: info@wika.com.my
www.wika.com.my
Singapore
WIKA Instrumentation PTE. LTD.
Singapore
Tel.: (+65) 6844 55 06
Fax: (+65) 6844 55 07
E-mail: info@wika.com.sg
www.wika.com.sg
Taiwan
WIKA Instrumentation Taiwan Ltd.
Pinjen, Taoyuan
Tel.: (+886) 3 420 6052
Fax: (+886) 3 490 0080
E-mail: info@wika.com.tw
www.wika.com.tw
Australia
Australia
WIKA Australia Pty. Ltd.
Rydalmere NSW
Tel.: (+61) 2 8845 5222
Fax: (+61) 2 9684 4767
E-mail: sales@wika.com.au
www.wika.com.au
TR50
Surface RTD Sensor
Part of Your Business
TR50
TR50 Surface RTD Sensor
Part
Number
1
TR50 series RTD sensors are designed to typically measure the
~1 7/8"
(~48 mm)
„„ Magnet Style - spring loaded for magnetic
attachment to Ferro Magnetic material. It is
designed to maintain a positive contact on
regular and irregular surfaces and provides fast
and accurate temperature measurement.
2
X
„„ Metal Contact Block - primarily designed to be
welded or screwed to the measurement surface.
The junction is located inside the contact block
and gives a degree of insulation resistance
from the influence of ambient temperatures.
3
A
Process connection design
T
Washer
U
Magnet fixing
Q
Worm drive hose clamp fixing
O
Metal contact block
P
Weld on sheet
Sensor design
0
Straight
4
45 degree bend
9
90 degree bend
Unit of measure
I
M
„„ Worm drive hose clamp - a non-welded attachment.
Once the clamp is secured by pressure on the worm
drive screw there is a positive contact between
the sensor and the measurement surface.
Due to ambient/radiant temperature influences, the
accuracy of these sensors is primarily dependent upon the
amount of insulation surrounding the RTD element.
RTDs in this series can be supplied as a complete
assembly including connection head (enclosure) with a
terminal block or transmitter; or as a sensor only design.
2
5
Imperial
0
1
2
3
4
Applications:
TR50 series sensors are suitable for:
„„ Chemical and petrochemical industries
CSA Ex-proof Class 1 Division II
FM Ex-proof Class 1 Division II
A
EEx-i (ATEX) gas, acc. to directive
94/9/EC
Z
„„ Energy and power plant technology
EEx-n (ATEX) acc. to directive 94/9/EC
Without
BSS-H
17
18
19
20
21
22
S
1/2 NPT
K
-50...+250 °C
J
Inconel® 600 (2.4816)
F
3/4 NPT
S
-50…+450 °C
E
Electrical cord grip
X
Iron, magnetic
T
M20 x 1.5
M
-200...+250 °C
D
3-pin-plug
Q
Stainless steel 316 Ti (1.4571)
K
3-pin-plug DIN Barnant (male)
Z
Without
T
-200...+450 °C
S
3-pin DIN Tegam/Keithley
H
-200...+600 °C
T
4-pin DIN Tegam/Keithley
L
0...+850 °C
5
0...+1000 °C
Sheath material
Stainless steel 316 Ti (1.4571)
G
Lemosa plug size 2 S (male)
I
Lemosa plug size 1 S (female)
J
Lemosa plug size 2 S (female)
6
T32 (HART® Transmitter)
L
Screw-in-plug (male)
8
T19 (Analogue Transmitter)
9
T53 (Fieldbus Foundation /
PROFIBUS PA Transmitter)
B
T91.10 (Analogue Transmitter, DIN
form B)
R
Terminals
X
Without / prepared for transmitter
Z
Without
Sensor diameter
1
1/4 inch / 0.250 inch (6.35 mm)
4
3/16 inch / 0.188 inch (4.75 mm)
2
1/8 inch / 0.125 inch (3.17 mm)
D
6.0 mm
B
3.0 mm
11
Lead wire insulation
Termination accessories
F
Cord grip
A
Braze adapter
B
Braze adapter and weatherproof boot
C
Cable clamp
D
Cable clamp and weatherproof boot
L
Teflon® jacket, shielded
Weld on sheet steel 25 x 25 x 3.0
mm (W x L x H) * 5
Weld on sheet steel 25 x 25 x 3.2
mm (W x L x H) * 5
T24 (Programmable Analogue
Transmitter)
Q
Teflon® jacket
Contact block 30 x 40 x 8 mm (W x
L x H) with drill-hole d = 6.5 mm * 4
4
Lemosa plug size 1 S (male)
T
7
T12 (Programmable Digital
Transmitter)
Connection head
F
Silicon jacket, shielded
Contact block 20 x 35 x 20 mm (W
x L x H) * 4
3
R
M
6
Ceramic terminal block
Inconel® 600 (2.4816)
Hex crimp adapter and
weatherproof boot
Contact block 25 x 20 x 3 mm (W
x L x H) * 4
2
J
H
5
Crastin terminal block
Miniature 3-pin-plug (male)
Silicon jacket
Contact block 8 x 20 x 8 mm (W x
L x H) * 4
1
M
PVC armour over Teflon®
Contact block 8 x 40 x 8 mm (W x
L x H) * 4
Terminal block / Transmitter
Stainless steel 316 / 316 L (1.4401
/ 1.4435)
J
3
14
P
D
Contact block 30 x 15 x 4 mm (W
x L x H) * 4
Temperature range
Spade lugs
1
2
17
Stripped leads
Worm drive hose clamp for pipe
diameter 7...17 mm * 3
„„ Pulp and paper
Cable entry
2
Hex crimp adapter
Contact block 30 x 40 x 8 mm (W
x L x H) * 4
13
1
Dual compression adapter
1
BS
16
15
Stainless steel 316 / 316 L (1.4401
/ 1.4435)
E
Worm drive hose clamp for pipe
diameter 97...112 mm * 3
BSZ
BSZ-K
14
Termination
G
6
BSS
9
10
PVC jacket, shielded
„„ Pipeline control
BSZ-H
BSZ-HK
Process fixing material
PVC jacket
5
BSZ-H
w/DIGITAL
INDICATOR
13
N
2
7000W
12
O
1
4000F
4000S
11
Horseshoe magnet * 2
„„ Oil and gas industries
Imperial Grid 1" x 1"
10
1
Worm drive hose clamp for pipe
diameter 78...93 mm * 3
„„ Water and wastewater treatment
9
Washer 5/8 x 5/16 x 1/4 inch /
15.9 x 7.9 x 6.4 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 60...75 mm * 3
„„ Turbines
8
9
4
Connection Heads
KN4-A
KN4-P
Washer 3/4 x 5/16 x 1/4 inch /
19.1 x 7.9 x 6.4 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 17...57 mm * 3
„„ Power and utilities
8
Washer 3/4 x 1/2 x 1/4 inch / 19.1 x
12.7 x 6.4 mm (OD x ID x Thickness) * 1
3
„„ Machinery, plant and tank measurement
7
Washer 3/4 x 1/2 x 3/8 inch /
19.1 x 12.7 x 9.5 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 14...34 mm * 3
„„ Ovens and boilers
7
P
Washer 1 x 5/8 x 3/8 inch / 25.4
x 15.9 x 9.5 mm (OD x ID x
Thickness) * 1
Washer 1 x 5/8 x 1/4 inch / 25.4 x 15.9
x 6.4 mm (OD x ID x Thickness) * 1
4
BVA
Washer 1 1/4 x 3/4 x 3/8 inch /
31.8 x 19.1 x 9.5 mm (OD x ID x
Thickness) * 1
6
8
6
Washer 1 1/2 x 5/16 x 3/8 inch /
38.1 x 7.9 x 9.5 mm (OD x ID x
Thickness) * 1
2
„„ Heating, ventilation, air-conditioning
and refrigeration systems
6
Washer 1 1/2 x 3/4 x 3/8 inch /
38.1 x 19.1 x 9.5 mm (OD x ID x
Thickness) * 1
Washer 1 1/4 x 3/4 x 1/4 inch /
31.8 x 19.1 x 6.4 mm (OD x ID x
Thickness) * 1
Metric
M
H
5
5
Electrical approval
L
4
Process connection ( S e e No t e s * )
7
4
3
Note: Some configurations are unavailable. Your WIKA sales person will notify you if you have made an incorrect selection
TR50-XX-X-X-XXXX-XXXXXX-XXXXXXXXXXXXXXXXX-XX
W
Five styles of attachment are available including magnet,
metal contact block, washer, weld-on sheet and worm drive
hose clamp.
„„ Weld on Sheet - a cost effective method of
surface measurement. This design has the sensor
welded to the pad and the pad is in turn welded
to a flat measuring surface. The simple, rigid
construction of this sensor, when welded in place,
offers repeatable temperature measurement.
1
Code
surface temperature of pipe, tubing, plate, ducts, or vessel walls.
„„ Washer Style - designed to be mounted over a
threaded stud that has been welded to the measuring
surface. It is held in place with a matching threaded
nut to facilitate a positive surface contact.
Create your product part number by selecting the appropriate assembly items from each of the
categories below. Enter the item code into the applicable box to generate the part number.
Element
W-Dimension (W)
*****
ZZZZZ
19
ZZZZ
Please specify (e.g. 84 mm = 0084)
(e.g. 9.5 inch = 0950)
Without
A-Dimension (A)
*****
21
Without
X-Dimension (X)
****
20
Please specify (e.g. 84 mm = 00084)
(e.g. 9.5 inch = 00095)
Please specify (e.g. 84 mm = 00084)
(e.g. 9.5 inch = 00950)
Certificates
D
Pt100, class B
1
Quality certificates
C
Pt100, class A
Z
Without
E
Pt10, class A
I
Compression adapter
J
Compression adapter and
weatherproof boot
A
Cu10, class B
K
Wire clamp
B
Ni120, class B
T
Additional text
L
Wire clamp and weatherproof boot
K
Pt1000, class B
Z
Without
M
Mini wire clamp
Z
Without
J
Pt1000, class A
L
Pt100, accuracy less than class B
S
Stainless steel braid over Teflon®
G
Teflon® armour over Teflon®
F
Individual Teflon® leads
B
Armoured Teflon®
H
Fibreglass jacket
1
4000 F (Aluminum)
E
Teflon® armour over fibreglass
2
4000 S (Stainless steel)
K
Stainless steel braid over fibreglass
3
7000 W (Aluminum)
C
Individual fibreglass leads
7
A
Armoured fibreglass
8
P
MI-cable conductor wire
12
15
18
Connection head
16
Wiring configuration
A
Single 2-wire
B
Single 3-wire
KN4-A (Aluminum)
C
Single 4-wire
KN4-P (Polypropylene)
D
Single 4B-wire
A
BS (Aluminum)
E
Dual 2-wire
B
BSZ (Aluminum)
F
Dual 3-wire
D
BSZ-H (Aluminum)
G
Dual 4-wire
E
BSS (Aluminum)
H
Dual 4B-wire
F
BSS-H (Aluminum)
I
BVA (Stainless steel)
J
BSZ-K (anti static Polyamide)
K
BSZ-HK (anti static Polyamide)
N
BSZ-H with digital temperature indicator
DIH10 (set to transmitter range)
P
Electrical enclosure (ABS)
Q
Electrical enclosure (Aluminum)
Z
Without
22
Additional order details
Notes
1
Use only with code T for Process
connection design (Field 1)
2
Use only with code U for Process
connection design (Field 1)
3
Use only with code Q for Process
connection design (Field 1)
4
Use only with code O for Process
connection design (Field 1)
5
Use only with code P for Process
connection design (Field 1)
Resistance Temperature Detectors
Process connection:
Magnet, metal contact
block, washer, weld-on
sheet or worm drive hose
clamp
Sensor Element:
Pt100, Pt1000, Pt10,
Cu10, or Ni120
Measuring range:
-200 °C to +1000 °C
(depending upon element)
Wiring configuration:
2, 3, or 4 wire
(single or dual)
„„ Class B to DIN
EN 60751
„„ Class A to DIN
EN 60751
„„ Less than class B
Electrical approvals:
CSA, FM, ATEX/IEC
„„ Lengths and
diameters standard
or customer specific
„„ Transmitter mounted
directly within
connection head
„„ Calibration - single
point, multiple points,
and to Callendar-Van
Dusen coefficients
Options:
WIKA worldwide
Features:
TR50 - Surface RTD Sensor
Classification tolerance:
Electrical
Temperature
Measurement
„„ Material traceability
of the conductors,
metal sheath and
mineral insulation
„„ Selectable accuracy
tolerance
„„ Special designs
„„ The assembly can be supplied with or without a
transmitter. Transmitters convert the resistance
signal from the RTD to a linear analogue or
digital output (commonly 4-20 mA). This signal
reduces potential inaccuracies by negating the
need for compensating output lead wires.
„„ The assembly has electrical approvals for
explosion proof hazardous locations, ingress
protection and general purpose areas.
„„ Electrical authorities that have registered these
approvals include CSA, FM, and ATEX/IEC.
Note: CSA and FM approvals apply only when
configured with a certified connection head
together with flexible armour and cord grip.
„„ Sheath materials available include stainless
steels, corrosion resistant and high temperature
oxidation resistant alloys. For temperatures
greater than 600°C it is advisable to utilize an
Inconel 600 sheath in place of stainless steel.
„„ RTD diameters are 0.125, 0.188 inch
or 0.250 also 3 or 6 mm.
„„ RTD temperature ranges are dependent on
the RTD element, sheath material, element
accuracy and the process attachment.
„„ Terminations include stripped leads, 3-pin plugs,
Tegam/Keithley plugs, spade lugs, Lemosa plugs
or connection head complete with cord grip.
„„ Termination accessories include cord
grip, cable or wire clamps, and braze,
crimp or compression adapters.
„„ If required the metal sheath can be formed
during manufacture or by the installer.
„„ Extension cable is available in a variety of
insulation and jacket materials. These include
interlocking flexible armour, braided stainless
steel, fibreglass, PTFE (Teflon®), PVC, and Silicon.
North America
Africa/Middle East
Canada
WIKA Instruments Canada Ltd.
Edmonton, Alberta
Tel.: (+1) 780 463 7035
Fax: (+1) 780 462 0017
E-mail: info@wika.ca
www.wika.ca
Benelux
WIKA Benelux
Echt
Tel.: (+31) 475 53 55 00
Fax: (+31) 475 53 54 46
E-mail: info@wika.nl
www.wika.nl
Romania
WIKA Instruments Romania S.R.L.
Bucuresti
Tel.: (+40) 21-456 31 38
Fax: (+40) 21-456 31 37
E-mail: m.anghel@wika.ro
www.wika.ro
Egypt
WIKA Alexander Wiegand
GmbH & Co. KG
Nasr City, Cairo
Tel.: (+20) 2-227 33 140
Fax: (+20) 2-227 33 140
E-mail: Ahmed.Azab@wika.de
Kazakhstan
TOO WIKA Kasachstan
Almaty
Tel.: (+7) 3272 33 08 48
Fax: (+7) 3272 78 99 05
E-mail: info@wika.kz
www.wika.kz
Mexico
Instrumentos WIKA México,
S.A. de C.V.
Álvaro Obregón
Tel.: (+52) 55 5020 5300
Fax: (+52) 55 5020 5301
E-mail: ventas@wika.com
www.wika.com.mx
Bulgaria
WIKA Bulgaria EOOD
Sofia
Tel.: (+359) 2 82138-10
Fax: (+359) 2 82138-13
E-mail: t.antonov@wika.bg
www.wika.bg
Russia
ZAO “WIKA MERA”
Moskau
Tel.: (+7) 495-648 01 80
Fax: (+7) 495-648 01 81
E-mail: info@wika.ru
www.wika.ru
Korea
WIKA Korea Ltd.
Seoul
Tel.: (+82) 2-869 05 05
Fax: (+82) 2-869 05 25
E-mail: info@wika.co.kr
www.wika.co.kr
Finland
WIKA Finland Oy
Helsinki
Tel.: (+358) 9-682 49 20
Fax: (+358) 9-682 49 270
E-mail: info@wika.fi
www.wika.fi
Serbia
WIKA Merna Tehnika d.o.o.
Beograd
Tel.: (+381) 11 2763 722
Fax: (+381) 11-753 674
E-mail: info@wika.co.yu
www.wika.co.yu
Iran
WIKA Instrumentation Pars
Kish Ltd.
Tehran
Tel.: (+98) 21- 8852 6730 3
Fax: (+98) 21- 8875 7413
E-mail: info@wika.ir
www.wika.ir
France
WIKA Instruments s.a.r.l.
Eragny-sur-Oise
Tel.: (+33) 1/34 30 84 84
Fax: (+33) 1/34 30 84 94
E-mail: info@wika.fr
www.wika.fr
Spain
Instrumentos WIKA, S.A.
Sabadell (Barcelona)
Tel.: (+34) 902 902 577
Fax: (+34) 933 938 666
E-mail: info@wika.es
www.wika.es
Germany - Head Office
WIKA Alexander Wiegand
GmbH & Co. KG
Klingenberg
Tel.: (+49) 9372 132-0
Fax: (+49) 9372 132-406
E-mail: info@wika.de
www.wika.de
Switzerland
MANOMETER AG
Hitzkirch
Tel.: (+41) 41 919 72 72
Fax: (+41) 41 919 72 73
E-mail: info@manometer.ch
www.manometer.ch
USA
WIKA Instrument Corporation
Lawrenceville, Georgia
Tel.: (+1) 770-513 8200
Fax: (+1) 770-338 5118
E-mail: info@wika.com
www.wika.com
South America
Argentina
WIKA Argentina S.A.
Buenos Aires
Tel.: (+54) 11 4730-1800
Fax: (+54) 11 4761-0050
E-mail: info@wika.com.ar
www.wika.com.ar
Brazil
WIKA DO BRASIL
Iperó - SP
Tel.: (+55) 15 3459 9700
Fax: (+55) 15 3266 1650
E-mail: marketing@wika.com.br
www.wika.com.br
Europe
Austria
WIKA Meßgerätevertrieb
Ursula Wiegand GmbH & Co. KG
Wien
Tel.: (+43) 1-8 69 16 31
Fax: (+43) 1-8 69 16 34
E-mail: info@wika.at
www.wika.at
**,"6
„„ Explosion protection:
CSA, FM (class I
division II / class
I zone II)
„„ Intrinsically safe
version: ATEX (EEx-i)
„„ Non-sparking version:
ATEX (EEx-n)
„„ RTD transmitter
matching
103-02017 11/2007 CA
Italy
WIKA Italiana SRL
Arese (Milano)
Tel.: (+39) 02-93 86 11
Fax: (+39) 02-93 86 174
E-mail: info@wika.it
www.wika.it
Poland
Kujawska Fabryka Manometrow
Wloclawek
Tel.: (+48) 54230 11 00
Fax: (+48) 54230 11 01
E-mail: info@manometry.com.pl
www.manometry.com.pl
Ukraine
WIKA Pribor GmbH
Donetsk
Tel.: (+38) 062 345-34-16
Fax: (+38) 062 345-34-17
E-mail: info@wika.donetsk.ua
www.wika.donetsk.ua
United Kingdom
WIKA Instruments Limited
Merstham, Redhill
Tel.: (+44) (0) 1737 644 008
Fax: (+44) (0) 1737 644 403
E-mail: info@wika.co.uk
www.wika.co.uk
South Africa
WIKA Instruments (Pty.) Ltd.
Gardenview, Johannesburg
Tel.: (+27) 11-621 00 00
Fax: (+27) 11-621 00 59
E-mail: sales@wika.co.za
www.wika.co.za
United Arab Emirates
WIKA Middle East FZE
Jebel Ali, Dubai
Tel.: (+971) 4-883 90 90
Fax: (+971) 4-883 91 98
E-mail: wikame@emirates.net.ae
Asia
China
WIKA International Trading
(Shanghai) Co., Ltd.
Shanghai
Tel.: (+86) 21 53 85 25 72
Fax: (+86) 21 53 85 25 75
E-mail: wikash@online.sh.cn
India
WIKA Instruments India Pvt. Ltd.
Wagholi, Pune
Tel.: (+91) 20-66293200
Fax: (+91) 20-66293325
E-mail: sales@wika.co.in
www.wika.co.in
Japan
WIKA Japan K.K.
Minato-ku, Tokyo
Tel.: (+81) 3-5439-6673
Fax: (+81) 3-5439-6674
E-mail: t-shimane@wika.co.jp
Malaysia
WIKA Instrumentation (M) Sdn Bhd
Puchong, Selangor
Tel.: (+03) 80631080
Fax: (+03) 80631070
E-mail: info@wika.com.my
www.wika.com.my
Singapore
WIKA Instrumentation PTE. LTD.
Singapore
Tel.: (+65) 6844 55 06
Fax: (+65) 6844 55 07
E-mail: info@wika.com.sg
www.wika.com.sg
Taiwan
WIKA Instrumentation Taiwan Ltd.
Pinjen, Taoyuan
Tel.: (+886) 3 420 6052
Fax: (+886) 3 490 0080
E-mail: info@wika.com.tw
www.wika.com.tw
Australia
Australia
WIKA Australia Pty. Ltd.
Rydalmere NSW
Tel.: (+61) 2 8845 5222
Fax: (+61) 2 9684 4767
E-mail: sales@wika.com.au
www.wika.com.au
TR50
Surface RTD Sensor
Part of Your Business
TR50
TR50 Surface RTD Sensor
Part
Number
1
TR50 series RTD sensors are designed to typically measure the
~1 7/8"
(~48 mm)
„„ Magnet Style - spring loaded for magnetic
attachment to Ferro Magnetic material. It is
designed to maintain a positive contact on
regular and irregular surfaces and provides fast
and accurate temperature measurement.
2
X
„„ Metal Contact Block - primarily designed to be
welded or screwed to the measurement surface.
The junction is located inside the contact block
and gives a degree of insulation resistance
from the influence of ambient temperatures.
3
A
Process connection design
T
Washer
U
Magnet fixing
Q
Worm drive hose clamp fixing
O
Metal contact block
P
Weld on sheet
Sensor design
0
Straight
4
45 degree bend
9
90 degree bend
Unit of measure
I
M
„„ Worm drive hose clamp - a non-welded attachment.
Once the clamp is secured by pressure on the worm
drive screw there is a positive contact between
the sensor and the measurement surface.
Due to ambient/radiant temperature influences, the
accuracy of these sensors is primarily dependent upon the
amount of insulation surrounding the RTD element.
RTDs in this series can be supplied as a complete
assembly including connection head (enclosure) with a
terminal block or transmitter; or as a sensor only design.
2
5
Imperial
0
1
2
3
4
Applications:
TR50 series sensors are suitable for:
„„ Chemical and petrochemical industries
CSA Ex-proof Class 1 Division II
FM Ex-proof Class 1 Division II
A
EEx-i (ATEX) gas, acc. to directive
94/9/EC
Z
„„ Energy and power plant technology
EEx-n (ATEX) acc. to directive 94/9/EC
Without
BSS-H
17
18
19
20
21
22
S
1/2 NPT
K
-50...+250 °C
J
Inconel® 600 (2.4816)
F
3/4 NPT
S
-50…+450 °C
E
Electrical cord grip
X
Iron, magnetic
T
M20 x 1.5
M
-200...+250 °C
D
3-pin-plug
Q
Stainless steel 316 Ti (1.4571)
K
3-pin-plug DIN Barnant (male)
Z
Without
T
-200...+450 °C
S
3-pin DIN Tegam/Keithley
H
-200...+600 °C
T
4-pin DIN Tegam/Keithley
L
0...+850 °C
5
0...+1000 °C
Sheath material
Stainless steel 316 Ti (1.4571)
G
Lemosa plug size 2 S (male)
I
Lemosa plug size 1 S (female)
J
Lemosa plug size 2 S (female)
6
T32 (HART® Transmitter)
L
Screw-in-plug (male)
8
T19 (Analogue Transmitter)
9
T53 (Fieldbus Foundation /
PROFIBUS PA Transmitter)
B
T91.10 (Analogue Transmitter, DIN
form B)
R
Terminals
X
Without / prepared for transmitter
Z
Without
Sensor diameter
1
1/4 inch / 0.250 inch (6.35 mm)
4
3/16 inch / 0.188 inch (4.75 mm)
2
1/8 inch / 0.125 inch (3.17 mm)
D
6.0 mm
B
3.0 mm
11
Lead wire insulation
Termination accessories
F
Cord grip
A
Braze adapter
B
Braze adapter and weatherproof boot
C
Cable clamp
D
Cable clamp and weatherproof boot
L
Teflon® jacket, shielded
Weld on sheet steel 25 x 25 x 3.0
mm (W x L x H) * 5
Weld on sheet steel 25 x 25 x 3.2
mm (W x L x H) * 5
T24 (Programmable Analogue
Transmitter)
Q
Teflon® jacket
Contact block 30 x 40 x 8 mm (W x
L x H) with drill-hole d = 6.5 mm * 4
4
Lemosa plug size 1 S (male)
T
7
T12 (Programmable Digital
Transmitter)
Connection head
F
Silicon jacket, shielded
Contact block 20 x 35 x 20 mm (W
x L x H) * 4
3
R
M
6
Ceramic terminal block
Inconel® 600 (2.4816)
Hex crimp adapter and
weatherproof boot
Contact block 25 x 20 x 3 mm (W
x L x H) * 4
2
J
H
5
Crastin terminal block
Miniature 3-pin-plug (male)
Silicon jacket
Contact block 8 x 20 x 8 mm (W x
L x H) * 4
1
M
PVC armour over Teflon®
Contact block 8 x 40 x 8 mm (W x
L x H) * 4
Terminal block / Transmitter
Stainless steel 316 / 316 L (1.4401
/ 1.4435)
J
3
14
P
D
Contact block 30 x 15 x 4 mm (W
x L x H) * 4
Temperature range
Spade lugs
1
2
17
Stripped leads
Worm drive hose clamp for pipe
diameter 7...17 mm * 3
„„ Pulp and paper
Cable entry
2
Hex crimp adapter
Contact block 30 x 40 x 8 mm (W
x L x H) * 4
13
1
Dual compression adapter
1
BS
16
15
Stainless steel 316 / 316 L (1.4401
/ 1.4435)
E
Worm drive hose clamp for pipe
diameter 97...112 mm * 3
BSZ
BSZ-K
14
Termination
G
6
BSS
9
10
PVC jacket, shielded
„„ Pipeline control
BSZ-H
BSZ-HK
Process fixing material
PVC jacket
5
BSZ-H
w/DIGITAL
INDICATOR
13
N
2
7000W
12
O
1
4000F
4000S
11
Horseshoe magnet * 2
„„ Oil and gas industries
Imperial Grid 1" x 1"
10
1
Worm drive hose clamp for pipe
diameter 78...93 mm * 3
„„ Water and wastewater treatment
9
Washer 5/8 x 5/16 x 1/4 inch /
15.9 x 7.9 x 6.4 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 60...75 mm * 3
„„ Turbines
8
9
4
Connection Heads
KN4-A
KN4-P
Washer 3/4 x 5/16 x 1/4 inch /
19.1 x 7.9 x 6.4 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 17...57 mm * 3
„„ Power and utilities
8
Washer 3/4 x 1/2 x 1/4 inch / 19.1 x
12.7 x 6.4 mm (OD x ID x Thickness) * 1
3
„„ Machinery, plant and tank measurement
7
Washer 3/4 x 1/2 x 3/8 inch /
19.1 x 12.7 x 9.5 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 14...34 mm * 3
„„ Ovens and boilers
7
P
Washer 1 x 5/8 x 3/8 inch / 25.4
x 15.9 x 9.5 mm (OD x ID x
Thickness) * 1
Washer 1 x 5/8 x 1/4 inch / 25.4 x 15.9
x 6.4 mm (OD x ID x Thickness) * 1
4
BVA
Washer 1 1/4 x 3/4 x 3/8 inch /
31.8 x 19.1 x 9.5 mm (OD x ID x
Thickness) * 1
6
8
6
Washer 1 1/2 x 5/16 x 3/8 inch /
38.1 x 7.9 x 9.5 mm (OD x ID x
Thickness) * 1
2
„„ Heating, ventilation, air-conditioning
and refrigeration systems
6
Washer 1 1/2 x 3/4 x 3/8 inch /
38.1 x 19.1 x 9.5 mm (OD x ID x
Thickness) * 1
Washer 1 1/4 x 3/4 x 1/4 inch /
31.8 x 19.1 x 6.4 mm (OD x ID x
Thickness) * 1
Metric
M
H
5
5
Electrical approval
L
4
Process connection ( S e e No t e s * )
7
4
3
Note: Some configurations are unavailable. Your WIKA sales person will notify you if you have made an incorrect selection
TR50-XX-X-X-XXXX-XXXXXX-XXXXXXXXXXXXXXXXX-XX
W
Five styles of attachment are available including magnet,
metal contact block, washer, weld-on sheet and worm drive
hose clamp.
„„ Weld on Sheet - a cost effective method of
surface measurement. This design has the sensor
welded to the pad and the pad is in turn welded
to a flat measuring surface. The simple, rigid
construction of this sensor, when welded in place,
offers repeatable temperature measurement.
1
Code
surface temperature of pipe, tubing, plate, ducts, or vessel walls.
„„ Washer Style - designed to be mounted over a
threaded stud that has been welded to the measuring
surface. It is held in place with a matching threaded
nut to facilitate a positive surface contact.
Create your product part number by selecting the appropriate assembly items from each of the
categories below. Enter the item code into the applicable box to generate the part number.
Element
W-Dimension (W)
*****
ZZZZZ
19
ZZZZ
Please specify (e.g. 84 mm = 0084)
(e.g. 9.5 inch = 0950)
Without
A-Dimension (A)
*****
21
Without
X-Dimension (X)
****
20
Please specify (e.g. 84 mm = 00084)
(e.g. 9.5 inch = 00095)
Please specify (e.g. 84 mm = 00084)
(e.g. 9.5 inch = 00950)
Certificates
D
Pt100, class B
1
Quality certificates
C
Pt100, class A
Z
Without
E
Pt10, class A
I
Compression adapter
J
Compression adapter and
weatherproof boot
A
Cu10, class B
K
Wire clamp
B
Ni120, class B
T
Additional text
L
Wire clamp and weatherproof boot
K
Pt1000, class B
Z
Without
M
Mini wire clamp
Z
Without
J
Pt1000, class A
L
Pt100, accuracy less than class B
S
Stainless steel braid over Teflon®
G
Teflon® armour over Teflon®
F
Individual Teflon® leads
B
Armoured Teflon®
H
Fibreglass jacket
1
4000 F (Aluminum)
E
Teflon® armour over fibreglass
2
4000 S (Stainless steel)
K
Stainless steel braid over fibreglass
3
7000 W (Aluminum)
C
Individual fibreglass leads
7
A
Armoured fibreglass
8
P
MI-cable conductor wire
12
15
18
Connection head
16
Wiring configuration
A
Single 2-wire
B
Single 3-wire
KN4-A (Aluminum)
C
Single 4-wire
KN4-P (Polypropylene)
D
Single 4B-wire
A
BS (Aluminum)
E
Dual 2-wire
B
BSZ (Aluminum)
F
Dual 3-wire
D
BSZ-H (Aluminum)
G
Dual 4-wire
E
BSS (Aluminum)
H
Dual 4B-wire
F
BSS-H (Aluminum)
I
BVA (Stainless steel)
J
BSZ-K (anti static Polyamide)
K
BSZ-HK (anti static Polyamide)
N
BSZ-H with digital temperature indicator
DIH10 (set to transmitter range)
P
Electrical enclosure (ABS)
Q
Electrical enclosure (Aluminum)
Z
Without
22
Additional order details
Notes
1
Use only with code T for Process
connection design (Field 1)
2
Use only with code U for Process
connection design (Field 1)
3
Use only with code Q for Process
connection design (Field 1)
4
Use only with code O for Process
connection design (Field 1)
5
Use only with code P for Process
connection design (Field 1)
Part of Your Business
TR50
TR50 Surface RTD Sensor
Part
Number
1
TR50 series RTD sensors are designed to typically measure the
~1 7/8"
(~48 mm)
„„ Magnet Style - spring loaded for magnetic
attachment to Ferro Magnetic material. It is
designed to maintain a positive contact on
regular and irregular surfaces and provides fast
and accurate temperature measurement.
2
X
„„ Metal Contact Block - primarily designed to be
welded or screwed to the measurement surface.
The junction is located inside the contact block
and gives a degree of insulation resistance
from the influence of ambient temperatures.
3
A
Process connection design
T
Washer
U
Magnet fixing
Q
Worm drive hose clamp fixing
O
Metal contact block
P
Weld on sheet
Sensor design
0
Straight
4
45 degree bend
9
90 degree bend
Unit of measure
I
M
„„ Worm drive hose clamp - a non-welded attachment.
Once the clamp is secured by pressure on the worm
drive screw there is a positive contact between
the sensor and the measurement surface.
Due to ambient/radiant temperature influences, the
accuracy of these sensors is primarily dependent upon the
amount of insulation surrounding the RTD element.
RTDs in this series can be supplied as a complete
assembly including connection head (enclosure) with a
terminal block or transmitter; or as a sensor only design.
2
5
Imperial
0
1
2
3
4
Applications:
TR50 series sensors are suitable for:
„„ Chemical and petrochemical industries
CSA Ex-proof Class 1 Division II
FM Ex-proof Class 1 Division II
A
EEx-i (ATEX) gas, acc. to directive
94/9/EC
Z
„„ Energy and power plant technology
EEx-n (ATEX) acc. to directive 94/9/EC
Without
BSS-H
17
18
19
20
21
22
S
1/2 NPT
K
-50...+250 °C
J
Inconel® 600 (2.4816)
F
3/4 NPT
S
-50…+450 °C
E
Electrical cord grip
X
Iron, magnetic
T
M20 x 1.5
M
-200...+250 °C
D
3-pin-plug
Q
Stainless steel 316 Ti (1.4571)
K
3-pin-plug DIN Barnant (male)
Z
Without
T
-200...+450 °C
S
3-pin DIN Tegam/Keithley
H
-200...+600 °C
T
4-pin DIN Tegam/Keithley
L
0...+850 °C
5
0...+1000 °C
Sheath material
Stainless steel 316 Ti (1.4571)
G
Lemosa plug size 2 S (male)
I
Lemosa plug size 1 S (female)
J
Lemosa plug size 2 S (female)
6
T32 (HART® Transmitter)
L
Screw-in-plug (male)
8
T19 (Analogue Transmitter)
9
T53 (Fieldbus Foundation /
PROFIBUS PA Transmitter)
B
T91.10 (Analogue Transmitter, DIN
form B)
R
Terminals
X
Without / prepared for transmitter
Z
Without
Sensor diameter
1
1/4 inch / 0.250 inch (6.35 mm)
4
3/16 inch / 0.188 inch (4.75 mm)
2
1/8 inch / 0.125 inch (3.17 mm)
D
6.0 mm
B
3.0 mm
11
Lead wire insulation
Termination accessories
F
Cord grip
A
Braze adapter
B
Braze adapter and weatherproof boot
C
Cable clamp
D
Cable clamp and weatherproof boot
L
Teflon® jacket, shielded
Weld on sheet steel 25 x 25 x 3.0
mm (W x L x H) * 5
Weld on sheet steel 25 x 25 x 3.2
mm (W x L x H) * 5
T24 (Programmable Analogue
Transmitter)
Q
Teflon® jacket
Contact block 30 x 40 x 8 mm (W x
L x H) with drill-hole d = 6.5 mm * 4
4
Lemosa plug size 1 S (male)
T
7
T12 (Programmable Digital
Transmitter)
Connection head
F
Silicon jacket, shielded
Contact block 20 x 35 x 20 mm (W
x L x H) * 4
3
R
M
6
Ceramic terminal block
Inconel® 600 (2.4816)
Hex crimp adapter and
weatherproof boot
Contact block 25 x 20 x 3 mm (W
x L x H) * 4
2
J
H
5
Crastin terminal block
Miniature 3-pin-plug (male)
Silicon jacket
Contact block 8 x 20 x 8 mm (W x
L x H) * 4
1
M
PVC armour over Teflon®
Contact block 8 x 40 x 8 mm (W x
L x H) * 4
Terminal block / Transmitter
Stainless steel 316 / 316 L (1.4401
/ 1.4435)
J
3
14
P
D
Contact block 30 x 15 x 4 mm (W
x L x H) * 4
Temperature range
Spade lugs
1
2
17
Stripped leads
Worm drive hose clamp for pipe
diameter 7...17 mm * 3
„„ Pulp and paper
Cable entry
2
Hex crimp adapter
Contact block 30 x 40 x 8 mm (W
x L x H) * 4
13
1
Dual compression adapter
1
BS
16
15
Stainless steel 316 / 316 L (1.4401
/ 1.4435)
E
Worm drive hose clamp for pipe
diameter 97...112 mm * 3
BSZ
BSZ-K
14
Termination
G
6
BSS
9
10
PVC jacket, shielded
„„ Pipeline control
BSZ-H
BSZ-HK
Process fixing material
PVC jacket
5
BSZ-H
w/DIGITAL
INDICATOR
13
N
2
7000W
12
O
1
4000F
4000S
11
Horseshoe magnet * 2
„„ Oil and gas industries
Imperial Grid 1" x 1"
10
1
Worm drive hose clamp for pipe
diameter 78...93 mm * 3
„„ Water and wastewater treatment
9
Washer 5/8 x 5/16 x 1/4 inch /
15.9 x 7.9 x 6.4 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 60...75 mm * 3
„„ Turbines
8
9
4
Connection Heads
KN4-A
KN4-P
Washer 3/4 x 5/16 x 1/4 inch /
19.1 x 7.9 x 6.4 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 17...57 mm * 3
„„ Power and utilities
8
Washer 3/4 x 1/2 x 1/4 inch / 19.1 x
12.7 x 6.4 mm (OD x ID x Thickness) * 1
3
„„ Machinery, plant and tank measurement
7
Washer 3/4 x 1/2 x 3/8 inch /
19.1 x 12.7 x 9.5 mm (OD x ID x
Thickness) * 1
Worm drive hose clamp for pipe
diameter 14...34 mm * 3
„„ Ovens and boilers
7
P
Washer 1 x 5/8 x 3/8 inch / 25.4
x 15.9 x 9.5 mm (OD x ID x
Thickness) * 1
Washer 1 x 5/8 x 1/4 inch / 25.4 x 15.9
x 6.4 mm (OD x ID x Thickness) * 1
4
BVA
Washer 1 1/4 x 3/4 x 3/8 inch /
31.8 x 19.1 x 9.5 mm (OD x ID x
Thickness) * 1
6
8
6
Washer 1 1/2 x 5/16 x 3/8 inch /
38.1 x 7.9 x 9.5 mm (OD x ID x
Thickness) * 1
2
„„ Heating, ventilation, air-conditioning
and refrigeration systems
6
Washer 1 1/2 x 3/4 x 3/8 inch /
38.1 x 19.1 x 9.5 mm (OD x ID x
Thickness) * 1
Washer 1 1/4 x 3/4 x 1/4 inch /
31.8 x 19.1 x 6.4 mm (OD x ID x
Thickness) * 1
Metric
M
H
5
5
Electrical approval
L
4
Process connection ( S e e No t e s * )
7
4
3
Note: Some configurations are unavailable. Your WIKA sales person will notify you if you have made an incorrect selection
TR50-XX-X-X-XXXX-XXXXXX-XXXXXXXXXXXXXXXXX-XX
W
Five styles of attachment are available including magnet,
metal contact block, washer, weld-on sheet and worm drive
hose clamp.
„„ Weld on Sheet - a cost effective method of
surface measurement. This design has the sensor
welded to the pad and the pad is in turn welded
to a flat measuring surface. The simple, rigid
construction of this sensor, when welded in place,
offers repeatable temperature measurement.
1
Code
surface temperature of pipe, tubing, plate, ducts, or vessel walls.
„„ Washer Style - designed to be mounted over a
threaded stud that has been welded to the measuring
surface. It is held in place with a matching threaded
nut to facilitate a positive surface contact.
Create your product part number by selecting the appropriate assembly items from each of the
categories below. Enter the item code into the applicable box to generate the part number.
Element
W-Dimension (W)
*****
ZZZZZ
19
ZZZZ
Please specify (e.g. 84 mm = 0084)
(e.g. 9.5 inch = 0950)
Without
A-Dimension (A)
*****
21
Without
X-Dimension (X)
****
20
Please specify (e.g. 84 mm = 00084)
(e.g. 9.5 inch = 00095)
Please specify (e.g. 84 mm = 00084)
(e.g. 9.5 inch = 00950)
Certificates
D
Pt100, class B
1
Quality certificates
C
Pt100, class A
Z
Without
E
Pt10, class A
I
Compression adapter
J
Compression adapter and
weatherproof boot
A
Cu10, class B
K
Wire clamp
B
Ni120, class B
T
Additional text
L
Wire clamp and weatherproof boot
K
Pt1000, class B
Z
Without
M
Mini wire clamp
Z
Without
J
Pt1000, class A
L
Pt100, accuracy less than class B
S
Stainless steel braid over Teflon®
G
Teflon® armour over Teflon®
F
Individual Teflon® leads
B
Armoured Teflon®
H
Fibreglass jacket
1
4000 F (Aluminum)
E
Teflon® armour over fibreglass
2
4000 S (Stainless steel)
K
Stainless steel braid over fibreglass
3
7000 W (Aluminum)
C
Individual fibreglass leads
7
A
Armoured fibreglass
8
P
MI-cable conductor wire
12
15
18
Connection head
16
Wiring configuration
A
Single 2-wire
B
Single 3-wire
KN4-A (Aluminum)
C
Single 4-wire
KN4-P (Polypropylene)
D
Single 4B-wire
A
BS (Aluminum)
E
Dual 2-wire
B
BSZ (Aluminum)
F
Dual 3-wire
D
BSZ-H (Aluminum)
G
Dual 4-wire
E
BSS (Aluminum)
H
Dual 4B-wire
F
BSS-H (Aluminum)
I
BVA (Stainless steel)
J
BSZ-K (anti static Polyamide)
K
BSZ-HK (anti static Polyamide)
N
BSZ-H with digital temperature indicator
DIH10 (set to transmitter range)
P
Electrical enclosure (ABS)
Q
Electrical enclosure (Aluminum)
Z
Without
22
Additional order details
Notes
1
Use only with code T for Process
connection design (Field 1)
2
Use only with code U for Process
connection design (Field 1)
3
Use only with code Q for Process
connection design (Field 1)
4
Use only with code O for Process
connection design (Field 1)
5
Use only with code P for Process
connection design (Field 1)
WIKA worldwide
North America
Europe
Canada
WIKA Instruments Canada Ltd.
Edmonton, Alberta
Tel.: (+1) 780 463 7035
Fax: (+1) 780 462 0017
E-mail: info@wika.ca
www.wika.ca
Austria
WIKA Meßgerätevertrieb
Ursula Wiegand GmbH & Co. KG
Wien
Tel.: (+43) 1-8 69 16 31
Fax: (+43) 1-8 69 16 34
E-mail: info@wika.at
www.wika.at
Mexico
Instrumentos WIKA México,
S.A. de C.V.
Álvaro Obregón
Tel.: (+52) 55 5020 5300
Fax: (+52) 55 5020 5301
E-mail: ventas@wika.com
www.wika.com.mx
Benelux
WIKA Benelux
Echt
Tel.: (+31) 475 53 55 00
Fax: (+31) 475 53 54 46
E-mail: info@wika.nl
www.wika.nl
USA
WIKA Instrument Corporation
Lawrenceville, Georgia
Tel.: (+1) 770 513 8200
Fax: (+1) 770 338 5118
E-mail: info@wika.com
www.wika.com
Bulgaria
WIKA Bulgaria EOOD
Sofia
Tel.: (+359) 2 82138-10
Fax: (+359) 2 82138-13
E-mail: t.antonov@wika.bg
www.wika.bg
USA
WIKA Instrument Corporation
Houston Facility
Deer Park, Texas
Tel.: (+1) 713 475 0022
Fax: (+1) 713 475 0011
E-mail: info@wikahouston.com
www.wika.com
Finland
WIKA Finland Oy
Helsinki
Tel.: (+358) 9-682 49 20
Fax: (+358) 9-682 49 270
E-mail: info@wika.fi
www.wika.fi
South America
Argentina
WIKA Argentina S.A.
Buenos Aires
Tel.: (+54) 11 4730-1800
Fax: (+54) 11 4761-0050
E-mail: info@wika.com.ar
www.wika.com.ar
Brazil
WIKA DO BRASIL
Iperó - SP
Tel.: (+55) 15 3459 9700
Fax: (+55) 15 3266 1650
E-mail: marketing@wika.com.br
www.wika.com.br
France
WIKA Instruments s.a.r.l.
Eragny-sur-Oise
Tel.: (+33) 1/34 30 84 84
Fax: (+33) 1/34 30 84 94
E-mail: info@wika.fr
www.wika.fr
Germany - Head Office
WIKA Alexander Wiegand
GmbH & Co. KG
Klingenberg
Tel.: (+49) 9372 132-0
Fax: (+49) 9372 132-406
E-mail: info@wika.de
www.wika.de
Italy
WIKA Italiana SRL
Arese (Milano)
Tel.: (+39) 02-93 86 11
Fax: (+39) 02-93 86 174
E-mail: info@wika.it
www.wika.it
Asia
Africa/Middle East
Poland
Kujawska Fabryka Manometrow
Wloclawek
Tel.: (+48) 54230 11 00
Fax: (+48) 54230 11 01
E-mail: info@manometry.com.pl
www.manometry.com.pl
China
WIKA International Trading
(Shanghai) Co., Ltd.
Shanghai
Tel.: (+86) 21 53 85 25 72
Fax: (+86) 21 53 85 25 75
E-mail: wikash@online.sh.cn
Egypt
WIKA Alexander Wiegand
GmbH & Co. KG
Nasr City, Cairo
Tel.: (+20) 2-227 33 140
Fax: (+20) 2-227 33 140
E-mail: Ahmed.Azab@wika.de
Romania
WIKA Instruments Romania S.R.L.
Bucuresti
Tel.: (+40) 21-456 31 38
Fax: (+40) 21-456 31 37
E-mail: m.anghel@wika.ro
www.wika.ro
India
WIKA Instruments India Pvt. Ltd.
Wagholi, Pune
Tel.: (+91) 20-66293200
Fax: (+91) 20-66293325
E-mail: sales@wika.co.in
www.wika.co.in
Russia
ZAO “WIKA MERA”
Moskau
Tel.: (+7) 495-648 01 80
Fax: (+7) 495-648 01 81
E-mail: info@wika.ru
www.wika.ru
Japan
WIKA Japan K.K.
Minato-ku, Tokyo
Tel.: (+81) 3-5439-6673
Fax: (+81) 3-5439-6674
E-mail: t-shimane@wika.co.jp
Iran
WIKA Instrumentation Pars
Kish Ltd.
Tehran
Tel.: (+98) 21- 8852 6730 3
Fax: (+98) 21- 8875 7413
E-mail: info@wika.ir
www.wika.ir
Serbia
WIKA Merna Tehnika d.o.o.
Beograd
Tel.: (+381) 11 2763 722
Fax: (+381) 11-753 674
E-mail: info@wika.co.yu
www.wika.co.yu
Spain
Instrumentos WIKA, S.A.
Sabadell (Barcelona)
Tel.: (+34) 902 902 577
Fax: (+34) 933 938 666
E-mail: info@wika.es
www.wika.es
Switzerland
MANOMETER AG
Hitzkirch
Tel.: (+41) 41 919 72 72
Fax: (+41) 41 919 72 73
E-mail: info@manometer.ch
www.manometer.ch
Ukraine
WIKA Pribor GmbH
Donetsk
Tel.: (+38) 062 345-34-16
Fax: (+38) 062 345-34-17
E-mail: info@wika.donetsk.ua
www.wika.donetsk.ua
United Kingdom
WIKA Instruments Limited
Merstham, Redhill
Tel.: (+44) (0) 1737 644 008
Fax: (+44) (0) 1737 644 403
E-mail: info@wika.co.uk
www.wika.co.uk
Kazakhstan
TOO WIKA Kasachstan
Almaty
Tel.: (+7) 3272 33 08 48
Fax: (+7) 3272 78 99 05
E-mail: info@wika.kz
www.wika.kz
Korea
WIKA Korea Ltd.
Seoul
Tel.: (+82) 2-869 05 05
Fax: (+82) 2-869 05 25
E-mail: info@wika.co.kr
www.wika.co.kr
Malaysia
WIKA Instrumentation (M) Sdn Bhd
Puchong, Selangor
Tel.: (+03) 80631080
Fax: (+03) 80631070
E-mail: info@wika.com.my
www.wika.com.my
Singapore
WIKA Instrumentation PTE. LTD.
Singapore
Tel.: (+65) 6844 55 06
Fax: (+65) 6844 55 07
E-mail: info@wika.com.sg
www.wika.com.sg
Taiwan
WIKA Instrumentation Taiwan Ltd.
Pinjen, Taoyuan
Tel.: (+886) 3 420 6052
Fax: (+886) 3 490 0080
E-mail: info@wika.com.tw
www.wika.com.tw
South Africa
WIKA Instruments (Pty.) Ltd.
Gardenview, Johannesburg
Tel.: (+27) 11-621 00 00
Fax: (+27) 11-621 00 59
E-mail: sales@wika.co.za
www.wika.co.za
United Arab Emirates
WIKA Middle East FZE
Jebel Ali, Dubai
Tel.: (+971) 4-883 90 90
Fax: (+971) 4-883 91 98
E-mail: wikame@emirates.net.ae
Australia
Australia
WIKA Australia Pty. Ltd.
Rydalmere NSW
Tel.: (+61) 2 8845 5222
Fax: (+61) 2 9684 4767
E-mail: sales@wika.com.au
www.wika.com.au