Fittings for ADSS Cable
NSF 151 8001 to NSF 151 8010
Features
• Tested together with the cable
The design enables excellent mechanical properties and
prevents slipping of the cable.
• Quick and easy tool-free installation
To usage the right fittings is very important to avoid damages of
the cable.
• Cold installation, no heating required
• Re-enterable
Description
Application
The NSF 151 8001 to NSF 8010 is a series of fittings for ADSS
cables.
The fittings are made of material that can withstand rough
weather. They do not expose the cable to compressive forces
which may lead to attenuation increase in the fiber.
The fittings are designed for quick and easy installation,
minimizing time consuming civil works. The fittings when used
with Hexatronic ADSS cables provide a future proof aerial
network that is easy to expand upgrade and maintain.
28701-NSF 151 8001 Uen Rev E
© Hexatronic Cables & Interconnect Systems AB
info@hexatronic.com
www.hexatronic.com
+46 10 453 02 00
1/4
Fittings for ADSS Cable
Suspension Pulley Clamps with Spiral Attachment
Suspension pulley clamps with spiral attachment are designed
for use with ADSS cables and for span lengths up to approximately 150 m. No slipping from unbalanced loads up to 2.5 kN
tensile force.
Ordering Information
product number
clamping range cable ø (mm)
length (mm)
no. of rods
rods ø (mm)
weight (kg)
NSF 151 8001/01
14.50 – 15.60
1050
10
3.51
1.,82
NSF 151 8001/02
13.42 – 14.49
1030
10
3.02
1.58
NSF 151 8001/03
12.36 - 13.41
940
10
3.02
1.53
NSF 151 8001/04
15.61 - 16.71
1140
10
3.51
1.89
NSF 151 8001/05
16.72 – 17.82
1180
10
3.51
1.93
NSF 151 8001/06
17.83 – 18.90
1220
10
3.51
1.97
NSF 151 8001/07
18.94 – 20.24
1240
10
3.51
2.01
NSF 151 8001/08
21.56 – 22.86
1270
10
3.51
2.09
NSF 151 8001/09
11.31 – 12.35
1020
10
3.02
1.56
Helical Dead Ends
to be used directly on the outer sheath.
Helical dead ends are ideally suited for the full tensioning of self
supporting optical fiber aerial cables. Dead ends are composed
of five or more preassembled helical rods which are covered
with small-grained sand on the inside to improve the frictional
contact. The loop of the dead end is protected from abrasion by
means of a thimble. The deformation of the cable is omitted as
the radial compression is distributed over a large contact area.
These particular dead ends are intended to be used directly on
the outer sheath of ADSS cables without protection rods.
Ordering Information
product number
clamping range cable ø (mm)
length (mm)
no. of rods
rods ø (mm)
weight (kg)
NSF 151 8002/01
14.50 – 16.50
1020
6
3.25
0.74
NSF 151 8002/02
17.30 – 19.30
1110
8
3.25
1.08
NSF 151 8002/03
21.70 – 23.70
1496
7
4.65
2.66
NSF 151 8003/01
13.28 – 14.35
860
5
3.02
0.52
NSF 151 8003/02
11.37 – 12.28
785
4
3.02
0.38
NSF 151 8003/03
14.36 – 15.50
930
5
3.51
0.76
NSF 151 8003/04
19.58 – 21.14
1265
6
3.51
1.23
NSF 151 8003/05
16.76 – 18.11
1085
5
3.51
0.88
NSF 151 8003/06
21.15 – 22.84
1370
6
3.51
1.33
NSF 151 8005/01
20.50 – 22.50
1520
6
4.65
2.22
28701-NSF 151 8001 Uen Rev E
© Hexatronic Cables & Interconnect Systems AB
info@hexatronic.com
www.hexatronic.com
+46 10 453 02 00
2/4
Fittings for ADSS Cable
b
Thimbles
r
d
NSF 151 8004/01
20
a
The thimbles together with helical dead ends serve for the
tensioning of self supporting optical fiber aerial cables.
NSF 151 8004/02
Ordering Information
product number
suitable for helical dead ends with
measurement (mm)
rated force (kn)
weight (kg)
clamping range (mm)
NSF 151 8004/01
12.0 – 19.3
a=50 b=30
For low tension
0.05
NSF 151 8004/03
16.9 – 32.5
a=50 b=44
For low tension
0.06
NSF 151 8004/06
7 – 12.5
a=40 b=21
For low tension
0.10
NSF 151 8004/02
15.1 – 22.5
d=50 r=30
100
0.90
NSF 151 8004/04
21.7 – 28.5
d=19 r=35
200
1.44
NSF 151 8004/05
28.5 – 39.0
d=19 r=38
200
1.90
Protection Rods
When aerial cables are used in long spans high tensile forces
will occur. To protect the cable protection rods are then used
together with the helical dead ends at the tension sets. They are
mounted beneath the helical dead end and spread the radial
forces on the cable uniformly along the zone of contact.
Protection rods
Ordering Information
product number
clamping range cable ø (mm)
length (mm)
no. of rods
rods ø (mm)
weight (kg)
NSF 151 8006/01
14.50 – 16.50
3000
15
3.25
2.95
NSF 151 8010/01
16.04 – 17.00
1850
17
3.02
1.90
NSF 151 8010/02
18.04 – 19.12
2020
19
3.02
2.30
NSF 151 8010/03
21.52 – 22.81
2460
15
4.37
4.67
28701-NSF 151 8001 Uen Rev E
© Hexatronic Cables & Interconnect Systems AB
info@hexatronic.com
www.hexatronic.com
+46 10 453 02 00
3/4
Fittings for ADSS Cable
Helical Dead Ends
to be used on protection rods.
abrasion by means of a thimble. The deformation of the cable is
omitted as the radial compression is distributed over a large
contact area.
Helical dead ends are ideally suited for the full tensioning of
self-supporting optical fiber aerial cables. Dead ends are
composed of five or more preassembled helical rods which are
covered with small-grained sand on the inside to improve the
frictional contact. The loop of the dead end is protected from
These particular dead ends are intended to be used on
protection rods.
Ordering Information
product number
clamping range cable ø (mm)
length (mm)
no. of rods
rods ø (mm)
weight (kg)
NSF 151 8005/01
20.50 – 22.50
1520
6
4.65
2.22
NSF 151 8009/01
22.03 – 23.24
1360
6
4.37
2.06
NSF 151 8009/02
24.54 – 25.89
1515
7
4.37
3.67
NSF 151 8009/03
30.44 – 32.12
1875
9
4.37
4.24
1
2
d
Vibration Dampers
L
Ordering Information
The vibration damper is composed of a helically formed plastic
rod. About one fifth of the overall length of the helix is of smaller
diameter. This section is used to attach the damper and
provides a completely reliable grip on the ADSS cable so that
the damper will not slip even on slopes. The remaining length of
the helix has no close contact to the cable. Due to differential
motions between ADSS cable and damper, the ADSS cable
vibrations are eliminated.
product number clamping range (mm) d (mm) length (mm)
weight (kg)
NSF 151 8007/01
13.7 – 15.24
12.5
1190
0.2
NSF 151 8007/02
11.03 – 12.29
12.5
1040
0.2
NSF 151 8007/03
12.30 – 13.70
12.5
1125
0.3
NSF 151 8007/04
15.25 – 16.99
12.5
1265
0.3
NSF 151 8007/05
17.00 – 18.94
16.0
1350
0.3
NSF 151 8007/06
18.95 – 21.10
16.0
1380
0.3
NSF 151 8007/07
21.12 – 23.53
16.0
1490
0.3
L
Oval Eye
28701-NSF 151 8001 Uen Rev E
© Hexatronic Cables & Interconnect Systems AB
D
Ordering Information
The oval eye is intended to act as an intermediate link between
thimble/helical dead end and pole hook. It is used if the hook is
too small to accommodate the thimble/helical dead end.
product number
b (mm)
l (mm)
d (mm)
NSF 151 8008
38
75
10
info@hexatronic.com
www.hexatronic.com
B
weight (kg)
+46 10 453 02 00
4/4