SPRING BOLTS – FINGER PULL LATCHES
No. 5597
No. 5597
Ideal for drawers and small cabinets.
Four standard holes can be furnished:
7/32" dia. on 1-1/8" x 1-1/4" centers.
Weight: .25 lbs.
Finish: All finger pulls are furnished
zinc-plated.
Consult factory for other finishes.
No. 3-5597
Same as No. 5597 except slide bolt
bevel is reversed.
6.7 lbs. Spring Rate
No. 6-5597
Same as No. 5597 except has
mounting holes.
No. 8-5597
No. 8-5597
Same as No. 3-5597 except has
mounting holes.
No. 31-5597
Same as No. 5597 except with 6 weld
studs, plated after assembly, and 9.7 lbs.
Spring Rate.
6.7 lbs. Spring Rate
No. 14-5597
Finger pull reversed, 6.7 lbs. Spring Rate, reversed bolt,
mounting holes.
No. 14-5597
6.7 lbs. Spring Rate
No. 15-5597
Finger pull, 2.6 lbs. Spring Rate, mounting holes.
No. 15-5597
2.6 lbs. Spring Rate
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
299
SPRING BOLTS – FINGER PULL LATCHES
No. 16-5597 has
4 adjustment mounting
slots that measure
.22" x .50". Short-angle
easy-slam bolt.
No. 23-5597 has
4 mounting holes and no
finger pull. Ideal to be
used with a cable or rod.
Slide bolt is reversed.
reversed.
2.2 lbs. Spring Rate
6.7 lbs. Spring Rate
No. 18-5597-U
Nut and bolt
shipped loose.
No. 20-5597 has
4 adjustment mounting
slots that measure
.22" x .50" and no
finger pull.
2.7 lbs. Spring Rate
2.7 lbs. Spring Rate
No. 21-5597-U
Inside Release Slam
Latch with handle cover.
No. 22-5597 has
2 mounting slots that
measure .22" x 1.00".
2.8 lbs. Spring Rate
2.7 lbs. Spring Rate
No. 26-5597-X
has 2 mounting holes
with .20 dia., 4 mounting
slots that measure
.22" x .25", a
reversed bolt.
No. 24-5597-U has
4 mounting slots with
reversed bolt, washer,
and bolt (bolt and nut
shipped loose).
6.7 lbs. Spring Rate
2.7 lbs. Spring Rate
Industrial Hardware Distributors, Inc.
300
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
97-LDP FLUSH BOLT
97-LDT FLUSH BOLT
! Steel construction/black E-coat finish
[ Available with standard or reverse bolt
[ Available with /without mounting holes
[ Available with optional spring tensions
! Steel construction/zinc finish
[ Available with standard or reverse bolt
[ Available with /without mounting holes
[ Available with optional spring tensions
3" Zinc Plated (2C) Chain Bolt – 812500
Features and Benefits
• For use on cabinet, double screen, garage and industrial doors
• Can be used on doors opening in by reversing the square bolt
• Equipped with a strong hard-drawn wire spring which throws the
bolt automatically when chain is released
• Full 24" long chain
• Includes surface and angle strike
Product Details
Length.......................... 3", 76.2mm
Bolt Length.................. 3
Bolt Size ...................... 3/8
Class ............................ SP1055
Finish ........................... 2C
Finish Description ...... Zinc Plated
4" Zinc Plated (2C)
Chain Bolt – 812520
6" Zinc Plated (2C)
Chain Bolt – 812550
4" Zinc Plated (2C)
Foot Bolt – 812620
6" Zinc Plated (2C)
Foot Bolt – 812650
Product Details
Length.......................... 4", 101.6mm
Bolt Length.................. 4
Bolt Size ...................... 7/16
Class ............................ SP1055
Finish ........................... 2C
Finish Description ...... Zinc Plated
Product Details
Length.......................... 6", 152.4mm
Bolt Length.................. 6
Bolt Size ...................... 9/16
Class ............................ SP1055
Finish ........................... 2C
Finish Description ...... Zinc Plated
Product Details
Length.......................... 4", 101.6mm
Bolt Length.................. 4
Bolt Size ...................... 19/32
Class ............................ SP1056
Finish ........................... 2C
Finish Description ...... Zinc Plated
Product Details
Length.......................... 6", 152.4mm
Bolt Length.................. 6
Bolt Size ...................... 3/4
Class ............................ SP1056
Finish ........................... 2C
Finish Description ...... Zinc Plated
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
301
SPRING BOLTS – FINGER PULL LATCHES
Spring Latches
Versatile Spring Latch Provides Secure Closure and Easy Access
The Spring Latch is reliable, low cost, used primarily on hinged doors and panels. The
simple barrelbolt fastener has many practical applications throughout the electronic
cabinet and industrial equipment industries. Smooth, trouble free action combined with
easy access and secure closure make the Spring Latch ideal for inspection doors and
access panels.
Spring Latch Features
Spring Latches are fabricated from quality materials including stainless steel, cold
rolled steel, and aluminum in a variety of finishes. They are available with optional
widths, hole patterns, forms and pin styles. Easy and inexpensive installation can be
accomplished using screws, rivets, or by welding.
The Spring Latch Difference
A unique design feature of the Spring Latch is a special C-Ring that acts as a
positive-stop retainer, preventing spring over-travel or snagging. The C-Ring also
provides secure pin retention and eliminates jamming. The tempered spring is
properly tensioned to provide smooth positive pin release and return.
SPRING LATCH PART NUMBERS
711
712
713
714
715
716
717
718
723
.250
PIN (01)
P
Pin Diameter
.125
.156
.187
.250
.187 SQ
.250
.187
.375
*E
Extension
.187
.250
.375
.500
.250
1.250
.375
1.00
.625
*R1
Handle Length
.437
.625
.687
.812
.610
.720
.72
1.50
.812
*R2
Handle Extension
.187
.250
.312
.375
.312
.375
.38
1.50
.430
2.75
BODY (02)
L
Length
.875
1.375
2.000
2.75
.875
3.50
2.500
4.00
W
Width A
.375
.500
.625
.75
.50
.720
.625
1.50
.955
Width B
.500
.750
.875
1.000
-
-
-
-
-
*T
Thickness
.040
.040
.050
.060
.050
.060
.060
.080
.090
*H1
Hole Location
.156
.187
.187
.250
.181
.281
.300
.620
.400
*H2
Hole Location
.156
.187
.250
.250
.156
.750
.375
.750
.375
*D
Hole Diameter
(2) .128
(2) .128
(3) .128
(3) .128
(2) .161
(2) .203
(2) .189
(2) .344
MATERIALS
Designation
Pin Type
Body
Spring
C-Ring
MODELS
POINT STYLES
Other styles
available including
long extensions
FINISH
Steel
S
12L14
1010
302
1060
R=
Right Hand
1 90° Cone
Stainless Steel
C
303
304
302
AISI 632
L=
Left Hand
2 Ball
Aluminum
A
SS
5052
302
AISI 632
U=
Unassembled
(3) .191
#715
#716 - 90°
Square Knuckle
& Square Pin
with 90° Form
3 Bullet
4 Flat
5 60° Cone
Most commercial finishes are available, including zinc and cadmium on steel,passivate and electropolishing on
stainless steel, and anodize on aluminum.
ORDERING
INFORMATION
* Designated dimensions that can be altered to meet your specifications. Special forms, offsets, swaging, hole sizes and positioning, or welding
projections are available to your specifications.
Industrial Hardware Distributors, Inc.
302
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
Spring Release Latches
& Hinges
700 Series
BODY
L
Length
W
Width
DASH #
PIN
P
Pin Diameter
T
Metal Thickness
DASH #
HOLES (4)
DASH #
MODELS
Combining a hinge and a latch in a standard piece of hardware.
The Spring Release Hinge has either a pair of spring-loaded handles
or a single handle, which pulls toward the center to release the body or
door from the keeper. An alternate style relies on an engagement hole
or slot in the adjoining surface. Installation is simple and inexpensive
using screws, rivets or by welding.
FINISH
3"
1"
-3"
4"
1"
-4"
6"
1"
-6"
Special
-7
.250
.281
Special
.050
.062
-1
-2
-7
None
Standard
Special
-0
-1
-7
Male
Female
Complete Assembly
-1
-2
-A
Most commercial finishes are available,
including zinc and cadmium on steel, passivate
and electropolishing on stainless steel, and
anodize on aluminum.
ORDERING
INFORMATION
All styles are manufactured to close tolerances. End play and side play
are held to a minimum, insuring a precision fit and smooth operation.
BODY
L
Length
W
Width
DASH #
PIN
P
Pin Diameter
T
Metal Thickness
DASH #
HOLES (2)
DASH #
MATERIAL
DASH #
MODEL
FINISH
ORDERING
INFORMATION
702 Series
Standard
1.75
1.00
-1
.250
.050
-1
None
-0
Alum.
-1
Special
-7
.281
Special
.062
-2
-7
Standard
Special
-1
-7
Steel
Stainless
-2
-3
Right
Left
R
L
Most commercial finishes are available,
including zinc and cadmium on steel, passivate
and electropolishing on stainless steel, and
anodize on aluminum.
BODY
L
Length
W
Width
DASH #
PIN
P
Pin Diameter
T
Metal Thickness
DASH #
HOLES (4)
DASH #
MATERIAL
DASH #
MODEL
FINISH
701 Series
Standard
1.75
1.00
-1
Special
-7
.250
.050
-1
None
-0
Alum.
-1
.281
Special
.062
-2
-7
Standard
Special
-1
-7
Steel
Stainless
-2
-3
Right
Left
R
L
Most commercial finishes are available,
including zinc and cadmium on steel, passivate
and electropolishing on stainless steel, and
anodize on aluminum.
ORDERING
INFORMATION
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
303
SPRING BOLTS – FINGER PULL LATCHES
No. 25-5597-U
No. 25-5597-U
4 mounting holes with reversed bolt, nut and washer (bolt and nut
shipped loose).
2.7 lbs. Spring Rate
No. 2-5598
No. 2-5598
4 mounting slots that measure .22" x .50"and a finger pull that has a
length of 4.00".
.9 lb. Spring Rate
No. 565692-U
No. 565692-U
Includes No. 565692-50 finger hook latch
and No. 565694-10 striker.
A simple, sturdy, spring-loaded latch that
may be used independently or in conjunction
with other latches (No. 565694-82X);
supplied with a steel strike with holes for
No. 10 screws.
26 lbs. Spring Rate
No. 565697
Flush-Type Steel
Latch Bolt
No. 565697
Same as Part No. 565692-U except has a
standard 45° bolt.
No. 11-565697
Same as 565697 except with reversed
bolt.
No. 17-565697
With 7 lb. spring.
25 lbs. Spring Rate
No. 18-565697
With 7 lb. spring with reversed bolt.
Industrial Hardware Distributors, Inc.
304
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
SIDE-ACTION
SLAM LATCHES
(FOR ROLLER SHUTTERS)
9/01455 (LH) with plain bolt-pull.
Bolt adjusted to 17mm, minimum projection.
9/01458 (RH) with ‘quick-fit’ attachment point.
Bolt adjusted to 25mm, max projection.
ORDERING CODE
SPECIFICATION
9/01455
Side-action latch LH
9/01456
Side-action latch RH
9/01457
Latch with ‘quick-fit’ pull,LH
9/01458
Latch with ‘quick-fit’ pull,RH
3/12497
Slotted bar, 915mm
3/22384
Packing plate
A. Bolt Thickness.................................................13mm
B. Bolt Pull...........................................................13mm
C. Width...............................................................57mm
D. Bolt Width........................................................19mm
E. Body Length ....................................................62mm
F. Hole Centres ................................................44.5mm
G. Hole Centres ...................................................33mm
H. Hole Diameter .............................................Ø 5.5mm
J. Hole Diameter .............................................Ø 5.0mm
Bolt projection variable, 17-25 mm.
Minimum load 5kg for full bolt travel.
Mild steel model made in CR4.
Stainless models in grade 304 with stainless bolt-pull, bolt
and spring.
Standard end latches with sidecut machined steel
bolts at 45° angle, making them suitable for roller
shutters or drop-down hatches. Adjustable boltpull allows projection to be varied, with ‘quick-fit’
attachment point for use with 2-way mechanisms.
Mount on door moving vertically downwards, latch
slams against a ramped striker plate.
Bolt retracts 13mm into case, either by slam-action or
by withdrawing bolt-pull.
Four holes, 5.5mm dia, through both thicknesses of
material. A packing plate is available (3/22384).
Zinc-plated finish on mild steel models.
Bolt spring pressure is 6kg (14lbs)
- Bolts to special dimensions – Top/bottom-knob models
- Stainless steel versions
SINGLE POINT
SLAM LATCHES
9/00279
‘Nose-up’
9/01243
‘Nose-down’
A range of compact slam latches derived from
our standard endbolts, but with direct action by
knob or loop handle. These models are useful
for seat squabs, gates and passive doors. They
are also available in stainless steel.
Dimensions as 3/22386,
Bolt-spring pressure 2.5kg.
PULL HANDLE LATCHES
The standard end-latch with a ‘loop’ handle in 6mm
diameter bar, raised at approx. 30° to horizontal.
9/01059
Bottom knob
latch
ORDERING CODE
Top-knob latch, nose-up mild steel
9/00279SS
Top-knob latch, nose-up
stainless steel
9/01059
Bottom-knob latch, mild steel
9/01059SS
Bottom-knob latch, stainless steel
9/01243
Top-knob latch, nose-down
mild steel
9/01243SS
Top-knob latch, nose-down
stainless steel
9/00028
Pull-handle latch, mild steel
Mild steel version is zinc-plated. Stainless steel version
is mill finished.
BOTTOM-KNOB LATCHES
Useful for cowls or doors which need to be operated
from outside. The knob can be removed, fitted through
appropriate slot in the panel, and screwed back. Bolt is
non-adjustable and non-reversible.
Stainless steel models are mill-finished but can
be bright polished to special request.
9/00279
TOP-KNOB LATCHES
Surface-mounted design with 20mm diameter knob,
at height 10mm above bolt case. Slam bolt projects
17mm and withdraws 15mm (non-adjustable and
non-reversible).
Slam bolt is adjustable, with projection variable from
9mm - 16mm, withdrawing approx. 9mm. Bolt can be
reversed to ‘nose-up’ position.
Mild steel version is zinc-plated.
9/00028
Pull-Handle Latch
Fully adjustable
and fully reversible.
Height of loop 33mm (max)
above surface. Also available
parallel to latch (height 13mm)
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
305
SPRING BOLTS – FINGER PULL LATCHES
No. 2100
Sturdy all metal construction
with slotted mounting
holes for easy adjustment.
Choice of threaded or
hex receptacle actuator
for use with authorized
tool. Actuator can be
extended through latch to
accept handle on inside.
Easy to mount and
assemble. Just screw or bolt
latch to that section and insert
threaded actuator into latch, securing with jam
nut as required. Meets specifications of Canadian Standards
Association (CSA) requirements. Available with
zinc-plated or E-coat.
No. 2100
No. 2100 threaded drive 8 x 1.25 mm
No. 2100-H hex drive 6 mm hex
No. 2-2100 1/4-20 threaded drive
No. 2200-H reverse bolt
Weight: .34 lbs.
No. 5620
Malleable
iron strike.
No. 5620
Finish: Zinc-plated
Weight: .13 lbs.
*Part No. 5619-A and 5620 strikers can be
used with any of the Eberhard paddle slam
latches or end bolts.
No. 5619-A
Has both a long primary catch and
a shorter secondary catch.
No. 5619-A
Also available in stainless steel as request quote
ref. No. 5619-SSA.
Finish: Zinc-plated
No.
Variations
Weight
5619-A
5619
With slots
Without slots
.06 lbs.
.06 lbs.
Industrial Hardware Distributors, Inc.
306
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
307
SPRING BOLTS – FINGER PULL LATCHES
‘FIX-THROUGH’
SLAM LATCH
IN STEEL
Special design allows ‘fix-through’
mounting, to suit narrow door pillars,
sections and channels. This is
interchangeable with our moulded
model (9/01530) but may be
preferred where there is possibility
of impact loads or lateral stress.
9/01186
ORDERING CODE
9/01186
‘Fix-through’ slam latch steel
Slam bolt retracts fully into case when operated. Slotted bolt-pull provides
‘lost-motion’ so latches can always be slammed, even when a system is in
‘locked’ mode.
Fixing by rivets through 7mm holes in case. Use large-headed fasteners to
spread load over area.
Bright zinc-plated
SPECIFICATION
A. Body Length .............................. 80mm
B. Max. Width ................................ 25mm
C. Max. Height ............................... 20mm
D. Projection .................................. 13mm
E. Location .................................... 20mm
F. Location .................................... 43mm
G. Location .................................... 23mm
H. Hole diameter ............................. 7mm
J. Slot dimensions .....................6x20mm
K. Knob diameter ........................ Ø38mm
L. Knob height (max) ..................... 20mm
Spring pressure: 5kg to full bolt withdrawal
SINGLE
POINT
SLAM
LATCHES
The basic steel latch can be
fitted with a large, knurled
moulded knob, riveted in
position in either ‘nose-up’
or ‘nose-down’ styles.
9/01728
‘nose-up’
9/01729
‘nose-down’
ORDERING CODE
9/01728
Latch & knob, nose-up
9/01729
Latch & knob, down
Industrial Hardware Distributors, Inc.
308
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
MOULDED
SLAM LATCHES
9/01528
‘Nose-up’ model
The unique design of these latches allows ‘fix
through’ mounting to suit narrow door pillars,
sections and channels. Moulded construction
provides the benefits of lightweight, self-lubricating
action, and total corrosion resistance at an
inexpensive price.
Basic Latch (9/01530) is operated by rod or cable as
part of a slam system. Single-point models use a large
knurled knob for good grip.
Slam bolt retracts fully into case when operated.
Slotted bolt-pull provides ‘lost-motion’ so latches can
always be slammed, even when a system is in ‘locked’
mode.
9/01529
‘Nose-down’ model
Fixing by rivets through 6mm holes in case. Use largeheaded fasteners to spread load over area.
Latches are self-coloured black with attractive textured
finish.
9/01530
Basic model
Moulded in acetal copolymer, with stainless steel
spring.
Tooling allows special bolt nose shapes to be made,
subject to economical minimum batches.
ORDERING CODE
9/01528
Moulded slam latch,
reversed knob
9/01529
Moulded slam latch,
pull-knob fitment
9/01530
Moulded slam latch
Cycle Testing: The slam latch 9/01530 was tested to
over 50,000 cycles of slam and withdrawal with no
appreciable wear to bolt-nose or bolt-pull.
Special model with side-action bolt,
suitable for roller shutters, etc.
Highly competitive against market alternatives.
SPECIFICATION
A.
B.
C.
D.
E.
F.
G.
H.
J.
K.
L.
Body Length ....................................................80mm
Body Width ......................................................29mm
Body Height.....................................................18mm
Bolt Projection.................................................16mm
Location ..........................................................23mm
Location ..........................................................44mm
Location ..........................................................25mm
Hole Diameter ................................................Ø 6mm
Slot Dimension ............................................ 7x20mm
Knob Diameter .............................................Ø 38mm
Knob Height (max) ..........................................16mm
Spring pressure: 6kg to full bolt withdrawal
Note: Knob & rivet can be supplied loose, for
assembly after latch is installed in panel.
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
309
SPRING BOLTS – FINGER PULL LATCHES
No. 2-565697
Same as No. 565697 except it has an offset steel latch bolt.
No. 2-565697
Offset-Type Steel
Latch Bolt
25 lb. Spring
25 lbs. Spring Rate
No. 17-565699-52XU
4 mounting holes .20" dia. and a 30° bolt (washer and bolt
shipped loose).
No. 17-565699-52XU
15 lbs. Spring Rate
No. 38-565699-S52U
6 mounting holes .28" dia. and a 45° bolt (washer and bolt
shipped loose).
No. 38-565699-S52U
15 lbs. Spring Rate
No. 4974-52U
4 mounting holes .20" dia. and a 45° bolt (washer and bolt
shipped loose).
No. 4974-52U
7 lbs. Spring Rate
Industrial Hardware Distributors, Inc.
310
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
311
SPRING BOLTS – FINGER PULL LATCHES
SPRING LOADED BOLTS W/FINGERPULL
Positive slam action bolts. All steel case. Reversible steel bolts w/45° and 60° taper. Ductile iron
bolt furnished w/double taper. Holes for 1/4" screws. Offset bolts are 1/2" offset. All parts are
zinc plated. For part numbers see below.
6011-050
6011-051
6011-052
6011-053
6011-054
6011-055
SPRING L
OADED BOL
TS W/HOLE FOR 3/8" ROD
LOADED
BOLTS
Positive slam action bolts. For use as endbolts on 6011 locks or in applications requiring a 3/8"
hole in bolt. All steel case. Reversible steel bolts w/45° and 60° taper. Ductile iron bolt furnished w/double taper. Holes for 1/4" screws. Offset bolts are 1/2" offset. All parts are zinc
plated. For part numbers see below.
Fingerpull No.
Endbolt No.
Description
6011-050
6011-051
6011-052
6011-053
6011-054
6011-055
6011-160
6011-161
6011-162
6011-163
6011-164
6011-165
45° taper bolt - flush
45° taper bolt - offset
60° taper bolt - flush
60° taper bolt - offset
double taper bolt -flush
double taper bolt - offset
STAINLESS STEEL SPRING BOLT
W/HOLD BACK
*
*
*
*
Locks open and closes quickly with a twist of the bolt
Self aligning bolt makes closing a cinch
Coil spring makes the latch self closing
Made from 11 gauge material w/.50 dia. bolt
Industrial Hardware Distributors, Inc.
312
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
Heavy Duty Spring Latches & Hook Latches
Heavy Duty Spring Latch Part Numbers
*Designated dimensions that can be
altered to meet your specifications.
Also available with hold back feature.
LEFT HAND SHOWN
Heavy-duty spring latches are available in 3/8" and
1/2" pin diameters. These large, rugged latches are
available in steel or stainless steel and have a closed
knuckle for added durability and strength.
719
720
PIN (01)
P=Pin Diameter
*E=Extension
*R1=Handle Length
*R2=Handle Extension
.375
1.250
1.187
.687
.500
1.500
1.218
1.000
BODY (02)
L=Length
W=Width
B=Height
T=Thickness
H1=Hole Location
H2=Hole Location
H3=Hole Location
*D=Hole Diameter
2.000
.656
1.12
.12
.375
.437
1.125
.265
3.000
.750
1.250
.19
.500
.625
1.750
.328
Materials Designation
C=Stainless
S=Steel
Models
R=Right Hand
L=Left Hand
U=Unassembled
Finish
Most commercial finishes are unavailable, including zinc and cadmium on steel, passivate and
electropolishing on stainless steel.
Special Hook Latch
All styles are manufactured to close tolerances. End play and side play are held to a
minimum, insuring a precision fit and smooth operation. Special forms, offsets, hole sizes
or welding projections are available to your specifications.
Item No.
P-Pin Diameter
L-Length
W-Width
Material
Models
Finish
780-C-R-Passivate
.375 in
3.50 in
.96 in
Stainless Steel
Right Hand
Passivate
780-C-RElectropolishing
.375 in
3.50 in
.96 in
Stainless Steel
Right Hand
Electropolishing
780-C-L-Passivate
.375 in
3.50 in
.96 in
Stainless Steel
Left Hand
Passivate
780-C-LElectropolishing
.375 in
3.50 in
.96 in
Stainless Steel
Left Hand
Electropolishing
780-C-U-Passivate
.375 in
3.50 in
.96 in
Stainless Steel
Unassembled
Passivate
780-C-UElectropolishing
.375 in
3.50 in
.96 in
Stainless Steel
Unassembled
Electropolishing
780-S-R-Zinc
.375 in
3.50 in
.96 in
Steel
Right Hand
Zinc
780-S-R-Cadmium
.375 in
3.50 in
.96 in
Steel
Right Hand
Cadmium
780-S-L-Zinc
.375 in
3.50 in
.96 in
Steel
Left Hand
Zinc
780-S-L-Cadmium
.375 in
3.50 in
.96 in
Steel
Left Hand
Cadmium
780-S-U-Zinc
.375 in
3.50 in
.96 in
Steel
Unassembled
Zinc
780-S-U-Cadmium
.375 in
3.50 in
.96 in
Steel
Unassembled
Cadmium
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
313
SPRING BOLTS – FINGER PULL LATCHES
Slam Latches – Available in 3 sizes:
7/16", 3/8", and 1/2" pins. These rugged latches are ideal for doors, drawers, truck/trailer bodies,
construction, farm equipment and all aircraft applications.
*Designated dimensions that can be
altered to meet your specifications.
Slam-Latch Part Numbers
707
708
709
PIN (01)
P=Pin Diameter
*E=Extension
*R1=Handle Length
*R2=Handle Extension
.375
.562
.812
1.000
.437
.750
1.000
1.250
.500
.750
1.250
1.375
BODY (02)
L=Length
*W=Width
T1=Height
T2=Thickness
*H1=Hole Location
*H2=Hole Location
H3=Hole Location
H4=Hole Location
*D=Hole Diameter
1.500
1.250
.115
.09
.187
.375
.750
.875
.171
2.000
1.625
.125
.12
.250
.375
1.250
1.125
.203
2.875
2.000
.150
.19
.312
.468
1.930
1.375
.265
Materials Designation
C=Stainless
S=Steel
Finish
Most commercial finishes are unavailable, including zinc and cadmium on steel, passivate and electropolishing on stainless
steel.
Ordering Information
Industrial Hardware Distributors, Inc.
314
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
Special Lock Latch
Design locks open,
and locks closed.
Special forms, offsets,
hole sizes or welding
projections are available
to your specifications.
Item No.
P-Pin Diameter
L-Length
W-Width
Material
Models
Finish
779-C-R-Passivate
.50 in
2.88 in
2.00 in
Stainless Steel
Right Hand
Passivate
779-C-RElectropolishing
.50 in
2.88 in
2.00 in
Stainless Steel
Right Hand
Electropolishing
779-C-L-Passivate
.50 in
2.88 in
2.00 in
Stainless Steel
Left Hand
Passivate
779-C-LElectropolishing
.50 in
2.88 in
2.00 in
Stainless Steel
Left Hand
Electropolishing
779-C-U-Passivate
.50 in
2.88 in
2.00 in
Stainless Steel
Unassembled
Passivate
779-C-UElectropolishing
.50 in
2.88 in
2.00 in
Stainless Steel
Unassembled
Electropolishing
779-S-R-Zinc
.50 in
2.88 in
2.00 in
Steel
Right Hand
Zinc
779-S-R-Cadmium
.50 in
2.88 in
2.00 in
Steel
Right Hand
Cadmium
779-S-L-Zinc
.50 in
2.88 in
2.00 in
Steel
Left Hand
Zinc
779-S-L-Cadmium
.50 in
2.88 in
2.00 in
Steel
Left Hand
Cadmium
779-S-U-Zinc
.50 in
2.88 in
2.00 in
Steel
Unassembled
Zinc
779-S-U-Cadmium
.50 in
2.88 in
2.00 in
Steel
Unassembled
Cadmium
.625 in
Super Heavy Duty Spring Latch
E=Extension
2.00 in
Item # 720-2
R1=Handle Length
2.00 in
R2=Handle Extension
2.51 in
T=Thickness
.187 in
L=Length
3.00 in
W1=Width
2.38 in
W2=Width
.88 in
H1=Hole Location
.328 in
H2=Hole Location
.63 in
H3=Hole Location
1.750 in
H4=Hole Location
1.750 in
D=Hole Diameter
.328 in
P=Pin Diameter
Material
Finish
LCS
Zinc Plate
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
315
SPRING BOLTS – FINGER PULL LATCHES
HEAVY-DUTY
SLAM LATCHES
9/00805
(LH)
Exceptionally robust latches with fitted release
handle for easy operation. There is a steel followbush so that when fitted on inside of a door, latch
can be operated from outside by a standard 8mm
square shaft. Suitable for heavy compartment doors
and some types of off-road vehicle cabs.
Latch slams against door edge on ramped striker, is
released by fitted handle or from reverse side through
8mm square follow bush.
Handle movement 45°, LH/RH as shown, with four
options available.
Follow bush
to take 8mm
steel shaft.
J
Plant-on fixing by bolts or rivets through 5mm diameter
holes on flanges. There is a bottom projection of 4mm
on follow-bush for location purposes.
C
H
A
E
SPECIFICATION
D
G
F
ORDERING CODE
9/00805
Slam latch LH, with handle
9/00806
Slam latch RH, with handle
9/00851
Special latch (clockwise)
9/00852
Special latch (anti-clockwise)
9/00803
Slam latch, non-handed
B
A.
B.
C.
D.
E.
F.
G.
H.
J.
Case Length ....................................................70mm
Case Width ......................................................64mm
Case Height .....................................................20mm
Bolt Width........................................................19mm
Bolt Projection.................................................15mm
Location (bush) ...............................................32mm
Handle Length ...............................................165mm
Hole Sizes (dia) .................................................5mm
Handle Height .................................................90mm
Depth Under Case .............................................4mm
Total bolt withdrawal ......................................10mm
Total Handle movement ...................................... 45°
Min. load for full bolt retraction ........................ 10kg
Zinc-plated, with black, nylon-dipped handle.
Bolt shape and projection variable, although total travel
cannot be altered.
Use with any of our diecast locking handles with 8mm
square shaft.
Illustration to show ‘handing’
P
O
EN
9/00805 (LH)
O
P
EN
9/00806 (RH)
NON-HANDED
SLAM LATCHES
SPECIAL MODELS WITH
SIDE-MOUNTED HANDLES
O
EN
P
P
EN
O
9/00851
9/00852
9/00803
(Non-handed)
Essentially the same latch as above, but non-handed
and without handle. Ideal for heavier doors where
strong spring action is required.
Industrial Hardware Distributors, Inc.
316
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
No. 5669-L
No. 5669-L&R
Compartment latches are designed and built with rugged
components – steel tumblers with powdered metal slide bolts and
stainless steel springs. Compartment latches are available in
stainless steel or zinc-plated carbon steel.
No. 5667-R
No. 5667-L&R
Compartment
latch.
Used primarily on utility truck
compartments.
Weight: .42 lbs.
Left-Hand Shown
No. 3-5669-R
No. 3-5669-L&R
Side latching slam
end bolt.
Used as side latching
end bolts for rod or remote
controlled cable locks.
Weight: .42 lbs.
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
317
SPRING BOLTS – FINGER PULL LATCHES
54 CAB LOCK
! Steel construction/zinc finish
! Accepts 5/16” shank
[ Available with/without inside handle
[ Available with left or right hand
[ Available with standard or reverse bolt (without handle)
2-27/64
1
1
1/2
.318 SQ. THRU
1/2 BOLT EXT.
1-15/16
2-3/32
2-15/16
1-1/16
41/64
9/16
9/64
13/16
2-3/8
2-7/8
1/4
.218 DIA
S54XXXLXZNXX
A
C
D
55 CAB LOCK
! Accepts 5/16” shank
[ Available in stainless steel
[ Available in steel construction/zinc finish
[ Available in left or right hand
[ Available with mounting flange
[ Available with inside override feature
[ Available with plastisol coating on handle
[ Available with heavy duty case
B
A
B
C
D
55
3 3/8
2
2 7/8
1
55A
4 11/32
2 3/8
3 5/8
1 1/2
F55XXXLSXXXX
All Dimensions are in inches
Industrial Hardware Distributors, Inc.
318
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
SPRING BOLTS – FINGER PULL LATCHES
Industrial Hardware Distributors, Inc.
620 Spicer St., Akron, OH 44311 • 800.824.1864 | 3415 S.W. 6th St., Ocala, FL 34474 • 800.682.8900
www.industrialhwe.com
319