Owners manual
reelMaster
Parts list
Easy care intructions
Changing direction
of retreive

KEY NO
1
2
3
4
5
6
7
8
9





PART NAME
SCREW (D/K)


DRAG KNOB
DRAG SHAFT
CLICK PIN
SPRING
SCREW (H/P)
HOUSING PLATE
WASHER
E-CLIP

PART NAME
SCREW (D/K)
DRAG KNOB
DRAG SHAFT
CLICK PIN
SPRING
SCREW (H/P)
HOUSING PLATE
WASHER
E-CLIP

KEY NO
10

11
12
13
14
15
16
17
18




PART NAME
DRAG PLATE








O-RING
KEY WASHER ("A")
DRAG WASHER(CARBON)
O/WAY ASS'Y
DRAG WASHER(CARBON)
SHAFT
WASHER
BUSH

PART NAME
DRAG PLATE
O-RING
KEY WASHER ("A")
DRAG WASHER(TEFLON)
KEY WASHER ("D")
DRAG WASHER(CARBON)
O/WAY ASS'Y
DRAG WASHER(CARBON)
KEY WASHER ("D")
GUIDELINE reelMaster LA flyreels come with an option of choosing both right hand and left hand retrieve when purchasing them.
These reels incorporate a state of the art sealed carbon/stainless
steel drag system that is resistant to water, dirt and moisture. There
is normally no need to open up the drag cylinder.
However, if you wish to acess it or have the need to change the
direction of the retrieve, please follow the steps below.




KEY NO
10
11
12
13
14
15
16
17
18


20
21
22
23
24
25
26
27






PART NAME
FRAME

FOOT
SCREW (FOOT)
WASHER
E-CLIP
O-RING (S/C)
SCREW (BALANCE)
SCREW (H/RIVET)
SPOOL




PART NAME
DRAG WASHER(TEFLON)
SHAFT
WASHER
BUSH
FRAME
FOOT
SCREW (FOOT)
WASHER
E-CLIP
KEY NO
28
29
30
31
32
33
34
35
36
29
30
31
32
33
34
35
36
KEY NO
28
Thank you for choosing this carefully designed GUIDELINE flyreel.
We are very proud that you decide to choose one of our products
among so many others.
We sincerely hope it will bring you years of good performance and
many great fish. Please take good care of your reel and try and
follow the instructions below to make sure it will perform to your
highest expectations in the most demanding conditions.
KEY NO
19


KEY NO
19
20
21
22
23
24
25
26
27
#6/8, #9/11


KEY NO
1
2
3
4
5
6
7
8
9
Reelmaster LA owners manual


KEY NO
37

PART NAME
HANDLE RIVET

HANDLE KNOB
SCREW (H/K)
SPOOL CAP
BALANCE

KEY NO
37
38
39
40
41
42
43
44
45
38
39
40
41
42
43
44
45


PART NAME
O-RING (S/C)
SCREW (BALANCE)
SCREW (H/RIVET)
SPOOL
HANDLE RIVET
HANDLE KNOB
SCREW (H/K)
SPOOL CAP
BALANCE




PART NAME

PART NAME
Always rinse or soak your reel in fresh water after using it. Take the
spool off the body, to get best possible access to all areas of the
reel. Remove sand and dirt with a soft, wet sponge or cloth. Rinse
thoroughly after cleaning, especially if you have used the reel in
salt water. Leave the reel to air dry before storing it for your next
trip. There is no need to open the sealed drag system for lubrication or adjustments. The inside of this reel is maintenance free. If
you want, you can apply a thin layer of grease on the shaft and the
locking areas of the spool.
Back off the drag to the lowest setting when the reel isn’t used.
Store in the protective reel case both on and off the fly rod.
reelMaster
How to change the direction of retreive
1. Remove spool from reel by unscrewing the relase spool cap. (35)
2. Pull the spool off the shaft.
3. Remove the E-clip from the main shaft. (27)
Then pull off the two thin metal washers.
4. Carefully remove the hexagraph screw (1) in the centre of the drag knob.
Pay special attention to the spring and click pin attached underneath.
5. Remove the click pin and the spring (4-5) from the hole.
6.Remove the 3 Philips head screws. (6)
7. Lift off the black housing plate. (7)
8. Lift out the stainless drag plate (10).
9. Remove the rubber o-ring and all washers, (10-15)
The one-way bearing is now exposed. Lift it out, turn it around and replace it,
making sure it is fitted correctly into into remaining washers and the three
slots in the cylinder walls.
10. Replace the washers you removed, making sure they are in same order
as before. Failure to do so may cause malfunction to the reel.
11. Replace the stainless and the Acetal cover plates. Make sure the click
pin and spring are fitted correctly.
12. When attaching the drag setting knob, make sure the numbers are set
so the 6 is in the free spool position. Fasten the centre hexagraph screw.
13. Replace washers and E-clip on the main shaft.
14. Fit the spool in place, making sure the straight edges are aligned on
spool and shaft.
Thank you for choosing a Guideline Fly Reel.
GUIDELINE fly reels come with a 3-year full service warranty against
manufacturer´s defects in material or workmanship. This guarantee is
valid for the first owner only. The warranty is limited to the repair or
exchange of the product and does not cover any type of damage caused
by neglect, normal wear or misuse.
www.guidelineflyfish.com I E-mail info@guidelineflyfish.com I Phone +46 31 92 36 50