Vellum
2x2
Recessed
INSTALLATION INSTRUCTIONS
PIN006700 Rev. B
These installation instructions are used for
luminaires
07/15 ECO3698
VMMRA/VMMRB
installing
and
the
following
kits:
Luminaire
Driver Kit
Dry Wall Mounting Kit (Optional)
VMMRA
VMMRB
VMMRBDK
FLNGW
FLNGW
WARNING: Please read the “important safety instructions” prior to installation of this product. The mounting
instructions can be found inside the mounting kits or downloaded from PeerlessLighting.com.
A) Identification of VMMRA / VMMRB Luminaire…………………….……………………………….…... Page 1
B) 2x2 Recessed T-grid Installation…………………………………………………………...……………..Page 2
C) Drywall Grid Adapter Option (FLNGW) - For hard ceilings ………..….……………………………… Page 3
D) VMMB (Remote driver) installation ………………………………...…………………………………… Page 4
A) Identification of VMMRA / VMMRB Luminaire
VMMRA –
INTEGRAL
DRIVER
IMPORTANT: Wear cotton gloves to lift and handle the luminaire
from the ends to avoid damaging or soiling the lens surface. Should
the lens surface become smudged or otherwise blemished, clean
using only a soft, microfiber cotton cloth.
VMMRB
REMOTE
DRIVER
–
IMPORTANT: Each VMMRB luminaire MUST
BE paired with its corresponding driver
enclosure VMMRBDK. Refer Packing Slip to
pair with matching line number (in front of
decimal point) and its CI code marked.
VMMRBDK
REMOTE
DRIVER BOX
1
PIN006700 Rev. B
07/15 ECO3698
B) 2x2 Recessed T-grid Installation
1
3
2
T-grid
VMMRA/VMMRB
BB
T-grid
LATC
XXX
T-grid
Guide wire
(By others)
PIN000000 Rev. X 00/00/00 ECO0000
No
touch
Locate luminaire. Rotate luminaire
housing and angle into 2x2 ceiling grid.
Note: Avoid contact with lens without
wearing glove (see “importance” on
Page 1)
4
Rest luminaire inside the center of grid
and ensure the luminaire rests securely
on the T-grid. Make sure luminaires are
oriented in same direction.
Attach provided LATC clips on each
mounting bracket. Adjust clips vertically
to engage with “T” member and tighten
screws. Do not over torque screws.
Secure luminaire to structure using guide
wires (by others) as required per local
code.
5
Access plate
Conduit (By others)
For VMMRA, remove access plate by
removing (2) screws. Make all necessary
electrical connections, and insert wires
back into the luminaire. Secure conduit to
driver enclosure. Re-install access plate
back on luminaire.
Luminaire
is
fully
installed.
Use
compressed air over entire lens to clean
up loose contaminants.
C) Drywall Grid Adapter Option (FLNGW) - For hard ceilings
2
1
Drywall
screws
Sheet
ceiling
#6 screws
(4x)
‘L’ bracket
(4x)
Drywall grid adapter kit comes assembled
with #6 screws (4x) and ‘L’ brackets (4x)
as illustrated above.
Holes for
guide
wires to
structure
rock
CONTRACTOR
TO
SPAKLE,
FEATHER AND
SAND TRIM
3
Guide wires to
structure (4x)
(By others)
APPROX.
½”
Attach provided LATC clips on each
mounting bracket. Adjust clips vertically
to engage with “T” member and tighten
screws. Do not over torque screws.
Secure luminaire to structure using guide
wires (by others) as required per local
code.
Remove access plate. Make all necessary
electrical connections, and insert wires
back into the luminaire. Install access
plate back on luminaire.
2
PIN006700 Rev. B
`
4
07/15 ECO3698
5
Conduit
(By
others)
VMMRA/VMMRB
BB
6
XXX
LUMINAIRE
PIN000000
Rev. X 00/00/00 ECO0000
RESTS
SECURELY
Access plate
Remove access plate by removing (2)
screws. Make all necessary electrical
connections, and insert wires back into the
luminaire. Secure conduit to driver
enclosure. Re-install access plate back on
luminaire.
Ensure the luminaire rests securely on
Dry wall kit with brackets on all sides.
Luminaire is fully installed. Use
compressed air over entire lens to clean
up loose contaminants.
D) VMMRB (Remote driver) installation
s
Plenum rated
(By others)
wires
Low voltage j-box
Ceiling
Access plate
Luminaire
Building wires
IMPORTANT: Wire connections
MUST be color matched. Black
to black & red to red.
Driver enclosure
Install luminaire in ceiling following steps mentioned in page 2 and 3 as needed. Place remote driver enclosure in electrical room.
Connect black and red coming out of driver enclosure to a matching set of colored wires (by others) leading to luminaire. Next, at
the luminaire, connect run of wires (by others) to terminal blocks underneath J-box making sure colors match.
Unscrew and remove access plate on driver enclosure. Run building wires to driver enclosure. Knock out one hole in access plate.
Pass building wires through hole. Perform wire splices, insert wires back into enclosure and reattach access plate.
IMPORTANT: Run wires (by others) from the driver enclosure to the luminaire following these requirements. Maximum distance
must not be exceeded.
Wire Gauge
18
16
14
12
Maximum Distance (ft.) (A + B)
56
102
176
272
3
PIN006700 Rev. B
07/15 ECO3698
E) VMMRB (Remote driver) with emergency battery pack (EL) installation
1
VMMRA/VMMRB
BB
Test switch
XXX
PIN000000 Rev. X 00/00/00 ECO0000
To luminaire
Position field mounting tray in desired locations across a 2’ section of the ceiling grid. Adjust bar hangers to correct width by
loosening side screw and then re-tightening to lock in place. Secure ends of bar hangers to T-bar using provided T-bar clips and
screws. T-bare clips and #10 screws can be found in a prepacked plastic bag.
2
Building wires
Low voltage j-box
Driver enclosure
Ceiling
IMPORTANT: Wire connections
MUST be color matched. Black
to black & red to red.
Luminaire
Install luminaire in ceiling following steps mentioned in page 2 and 3 as needed. Connect black and red coming out of driver
enclosure CONDUIT to a matching set of colored wires (by others) leading to luminaire.
Unscrew and remove access plate on driver enclosure. Run building wires to driver enclosure. Knock out one hole in access plate.
Pass building wires through hole. Perform wire splices, insert wires back into enclosure and reattach access plate.
IMPORTANT: The distance from driver enclosure to the luminaire must not exceed length of conduit provided – 2ft.
3
Insert one side of pilot switch into ½” hole and then snap other side into place. Slide mounting clip firmly. Install face plate onto Jbox (by others). Secure J-box onto ceiling and make sure pilot light is visible for testing.
4