Installation Instructions for
920MO2RAEH
Rae Head Two-Circuit Monorail
700MO2RAER_
1.0
HEADS-LOW VOLTAGE
GENERAL PRODUCT INFORMATION:
This product is suitable for indoor dry locations only.
This product should be used with Tech Lighting Two-Circuit
MonoRail system only.
1B
Install Fixture to Circuit 1 - Section 2
METAL
MONORAIL
CONNECTOR
CAP
Install Fixture to Circuit 2 - Section 1
Install Fixture as an Uplight - Section 3
TWO-CIRCUIT MONORAIL
CIRCUIT 2
TWO-CIRCUIT
MONORAIL
CIRCUIT 1
COM
3
NOTE: If space for the installation is limited, it may
be easier to install the fixture by removing the
second screw and completely removing the
MonoRail connector cap.
Install the Fixture to Circuit 2
1A
MONORAIL
CONNECTOR
1
Rotate and lift both MonoRail connector caps out of the
way and install the fixture onto the MonoRail.
1B
1C
METAL
MONORAIL
CONNECTOR
CAP
2
SCREW
4
4
ALLEN WRENCH
ALLEN WRENCH
NOTE: Circuit 2 installation requires one plastic and
one metal MonoRail connector cap.
1
Remove one of the screws from both MonoRail
connectors with the provided Allen wrench.
2
Loosen (do not remove) the other screw on both
MonoRail connectors with the provided Allen Wrench.
4
1
Reinstall both MonoRail connector caps, reinstall the
screws, and tighten them with the provided Allen
wrench.
1D
1B
METAL MONORAIL
CONNECTOR CAP CONNECTOR
CAP SET SCREW
6
8
PLASTIC MONORAIL
CONNECTOR CAP
UNUSED
SET SCREW
ALLEN
WRENCH
8
UNUSED
SET SCREW
8
ALLEN
WRENCH
8
7
COM
CIRCUIT 2
NOTE: The plastic MonoRail connector cap does not contain any set screws.
5
Ensure that the MonoRail is completely installed into both MonoRail connectors by pushing down the fixture until there is no
space between the top of the rail and connector caps.
6
Tighten the top set screw from each side of the metal MonoRail connector cap using the provided Allen wrench to connect
to circuit 2.
7
Tighten the bottom set screw from each side of the other MonoRail connector using the provided Allen wrench to connect
to com.
8
Remove the unused set screws from each side of both MonoRail connectors.
9
Skip to section 4A.
Install the Fixture to Circuit 1
2A
PLASTIC MONORAIL
CONNECTOR CAP
METAL MONORAIL
CONNECTOR CAP
PLASTIC
MONORAIL
CONNECTOR
CAP
2
6
MONORAIL
CONNECTOR
1
1
4
2
SCREW
SCREW
ALLEN
WRENCH
3
SCREW
ALLEN WRENCH
ALLEN
WRENCH
NOTE: Circuit 1 installation requires two plastic MonoRail connector caps.
1
Completely remove both screws from the MonoRail connector with the metal connector cap using the provided Allen
wrench and remove the metal connector cap.
2
Install the plastic MonoRail connector cap onto the same MonoRail connector, partially thread one of the screws into the
cap, and move the cap out of the way.
3
Remove one of the screws from the MonoRail connector with the plastic connector cap using the provided Allen wrench.
4
Loosen (do not remove) the other screw on the same MonoRail connector with the provided Allen Wrench.
5
Rotate the plastic MonoRail connector cap out of the way.
6
Install the fixture onto the MonoRail, completely install both MonoRail connector caps onto the MonoRail connectors,
reinstall the screws; and tighten them with the provided Allen wrench.
2
2B
1B
CIRCUIT 1
PLASTIC MONORAIL
CONNECTOR CAP
8
PLASTIC MONORAIL
CONNECTOR CAP
UNUSED
SET SCREW
ALLEN
WRENCH
10
ALLEN
WRENCH
10
9
COM
NOTE: The plastic MonoRail connector cap does not contain any set screws.
7
Ensure that the MonoRail is completely installed into the MonoRail connector by pushing down the fixture until there is no
space between the top of the rail and connector caps.
8
From the MonoRail connector that has one set screw, tighten the set screw from each side using the provided Allen wrench
to connect to circuit 1.
9
From the other MonoRail connector, tighten the bottom set screw from each side using the provided Allen wrench to
connect to com.
10
Remove the unused set screw from each side of the MonoRail connector.
11 Skip to section 4A.
Install the Fixture as an Uplight
3A
ALLEN WRENCH
ALLEN WRENCH
TWO-CIRCUIT
MONORAIL
SCREW
1
MONORAIL
CONNECTOR
2
4
4
METAL
MONORAIL
CONNECTOR
CAP
3
3
METAL
MONORAIL
CONNECTOR
CAP
NOTE: If space for the installation is limited, it may be easier to install the fixture by removing the second screw and completely
removing the MonoRail connector cap.
1
Remove one of the screws from both MonoRail connectors with the provided Allen wrench.
2
Loosen (do not remove) the other screw on both MonoRail connectors with the provided Allen Wrench.
3
Rotate and move both MonoRail connector caps out of the way and install the fixture onto the MonoRail.
4
Reinstall both MonoRail connector caps, reinstall the screws, and tighten them with the provided Allen wrench.
3
3B
1B
7
7
UNUSED
SET SCREW
6
COM
CIRCUIT 2 SET SCREW
9
CIRCUIT 1 SET SCREW
8
CIRCUIT 2
INSULATED MONORAIL
CONNECTOR CAP
ALLEN
WRENCH
CONNECTOR
CAP SET SCREW
CIRCUIT 1
5
Ensure that the MonoRail is completely installed into the MonoRail connector by pushing up the fixture until there is no
space between the bottom of the rail and connector caps.
6
Tighten the bottom set screw from each side of the metal MonoRail connector cap using the provided Allen wrench to
connect to com.
7
Remove the unused set screw from each side of the MonoRail connector.
8
If connecting the fixture to circuit 1,tighten the bottom set screw from each side of the connector and remove the unused
set screws from circuit 2.
9
If connecting the fixture to circuit 2,tighten the top set screw from each side of the connector and remove the unused set
screws from circuit 1.
Adjust the Fixture
4A
1B
1
Rotate the fixture to the desired position.
7400 Linder Ave, Skokie, IL 60077
847.410.4400
www.techlighting.com
SAVE THESE INSTRUCTIONS!
© 2015 Tech Lighting, L.L.C. All rights reserved. The "Tech Lighting" graphic is
a registered trademark of Tech Lighting, L.L.C. Tech Lighting reserves the right
to change specifications for product improvements without notification.
A Generation Brands Company
4