Horizontal Series FAN COIL TECHNICAL CATALOG BUILD YOUR REPUTATION ON OURS Horizontal Series TABLE OF CONTENTS 2 Table of Contents 3-4Portfolio 5 Features & Benefits 6 Unit Model Key 7 Ratings & Listings 8 Air Delivery 9 Sound Data 10-13 Fan Performance Curves 14 Electric Heating 15 Motor Data 16-25 Physical Data 26-30 Standard Features & Options 31 Piping Packages (Typical) International Environmental Corporation (IEC) works continually to improve its products. As a result, the design and specifications of each product may be changed without notice and may not be as described herein. Please contact IEC for information regarding current design and product specifications. Statements and other information contained herein are not express warranties and do not form the basis of any bargain between the parties but are merely IEC’s opinion or commendation of its products. Manufacturer’s standard limited warranty applies. 2 International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PORTFOLIO CHY - Horizontal Hideaway 200 CFM to 1200 CFM The Horizontal Hideaway (CHY) fan coil unit is designed specifically to meet the many varied requirements for a ceiling hideaway installation. The low-silhouette styling of the CHY makes this unit ideally suited for drop-ceiling and over-closet applications. Standard CHY units are provided with a galvanized finish. CBY - Horizontal Telescoping Hideaway 200 CFM to 1200 CFM The Horizontal Telescoping Hideaway (CBY) fan coil unit is mounted fully-recessed for ceiling-recessed applications. The CBY’s telescoping frame with hinged panel adapts to any ceiling type and ensures exact alignment of the panel with the ceiling. The hinged-bottom panel provides easy access to all internal components. Standard CBY units are provided with a galvanized finish on the cabinet and powder-coat paint finish on the bottom-access panel. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 3 Horizontal Series PORTFOLIO, Cont’d. CPY - Horizontal Hideaway with Plenum 200 CFM to 1200 CFM The Horizontal Hideaway with Plenum (CPY) fan coil unit provides the same basic features of the CHY plus a return air plenum for above-ceiling mounting in closets, hallways or bathroom areas. The CPY design enables the unit to be adapted to installations requiring return air ducts or to be used as a return-air plenum with a unit-mounted filter and filter-rack assembly. CPY units are shipped from the factory ready for installation with the plenum section in place. No field fabrication is required. CPY units are designed with interchangeable panels so that the unit may be modified on site to accommodate a rear or bottom return. Standard CPY units are provided with a galvanized finish. CXB - Horizontal Cabinet 200 CFM to 1200 CFM The Horizontal Cabinet (CXB) fan coil unit is designed specifically for exposed mounting in hotels, motels, hospitals, nursing homes, offices or other commercial establishments. With the CXB, valuable floor space is not required, and its slim, attractively-styled cabinet blends with all types of decor. Since there is no requirement for duct work or structure modifications, the CXB is ideal for retrofit applications. Standard CXB units are provided with a powder-coat paint finish. 4 International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series FEATURES & BENEFITS Application Fit • Optional airflow configuration (front supply, bottom • Multiple cabinet choices are available in 7 nominal CFM sizes for application in a variety of room layouts. o Horizontal Cabinet units (CXB) with aesthetically pleasing cabinetry offer capacities that are ideal for air conditioning in dormitories, small apartments, schools and many other applications. Front supply, bottom or rear return are available. o Horizontal Telescoping Hideaway units with painted access panel (CBY) allows smooth fit up to plaster or sheet rock ceilings. Standard units include bottom louvered return air with the filter located in the access panel. o Horizontal Hideaway models (CHY) units are installed above the ceiling with or without ducted supply air and open “soffit” return with an optional ceiling-mounted filter-grille. o Horizontal Hideaway models with plenum (CPY) units are installed above the ceiling with or without ducted supply air and ducted return air. The return air filter is either mounted on the unit plenum or installed in an optional ceiling filtergrille. supply, rear return or bottom return) to meet certain design limitations. • Outside air connections are available to meet ventilation requirements and reduce field labor (CXB/ CBY/CPY). • Wide variety of factory assembled valve packages to meet desired controls specifications. • Optional condensate overflow switch to address latest building codes where required. • Wide variety of optional insulation materials are available to address IAQ concerns. Ease of Installation • Factory assembled valve packages minimize piping work at the job site (shipped loose for field mounting). • Optional unit mounted controls, service switches and fusing minimize the electrical work required on site. • Units are tagged at the factory for clear identification on job site. • Opposite end connection units may minimize the piping work on renovation jobs. Ease of Service Design Flexibility • Easy to use ratings program to speed up project design. • Standard and high capacity hydronic coils and DX coils are available to match the heating and cooling loads of • All components are accessible by simply removing the access panel. • Filters can be replaced without tools or by opening the bottom panels on exposed units. • Blower assembly easily removed from the rear of coil the space. • Optional powder-paint finish colors and grille selections will complement most décors (exposed units). • CXB and CBY units ordered with optional rear return are constructed with a solid bottom panel. • Customizable cabinetry makes these units ideal for renovation jobs or where special sizes are required to for service and cleaning. Quality and Safety • Every unit is tested and inspected at the factory for trouble free start-up. • ETL and CETL listed. • AHRI certified. fit oversized valves and control packages. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 5 Horizontal Series UNIT MODEL KEY Code Items Code CHY CPY CBY CXB • • • • 01 C B 02 Y 03 0 4 04 A Y Y Y 04a C B Y Y 05 C 2 UNIT VINTAGE SIZE COILS ELECTRIC HEAT HAND/ MOTOR ARRANGEMENT 02 03 04 06 08 10 Horizontal Hideaway Horizontal Hideaway with Plenum Horizontal Telescoping Hideaway Horizontal Cabinet • • • • • • 200 CFM 300 CFM 400 CFM 600 CFM 800 CFM 1000 CFM Voltage Type C • 115-1-60 2• A• B• C• D • 208-1-60 E • 230-1-60 F • 277-1-60 V • 220-1-50* 12 • 1200 CFM 07 C P B CONTROLS Permanent Split Capacitor ECM, 3-Spd Relay Brd (L/M/H) ECM, Proportional (0-10VDC) ECM, 4-Spd EVO Board, Solid State w/PWM U • 240-1-50* Two-pipe Cooling and Heating or Four-pipe Cooling Four-pipe Heating Coil Connection Coil Construction A • 3 Row B • 4 Row D • 2 Row Y • None 6 • 1 Row 7 • 2 Row Y • None S • Same End O • Opposite End Y • Std S • SS Wrapper R • 3 Row, AAV S • 4 Row, AAV 06 R 5 Hand*** Arrangement R • Right L • Left 5 6 6 CHY, BHY Voltage kW** C D E F V U AY BY CY DY FY GY • 120 V • 208 V • 240 V • 277 V • 220 V (50)* • 240 V (50)* • • • • • • Stages 0.50 1.00 1.50 2.00 3.00 4.00 HY JY KY LY NY YY • • • • • • 5.00 6.00 7.00 8.00 10.00 None 6 Y • Single Stage Only CPY, BPY 5 6 CBY 5 Y • None 6 CXB 5 Voltage System B C D E F V U Manual Fan Operation Thermostat A • Standard Wall Mount (Switch Only) A B P N F • • • • • • • 24 V 120 V 208 V 240 V 277 V 220 V (50)* 240 V (50)* * Consult factory for 50Hz applications. ** Note that kWs depend on voltage and unit size. Function Control G • 2 Pipe Heat Only H • 2 Pipe Cool Only K • 2 Pipe Heat and Cool M • 2 Pipe Heat and Cool w/Aux. Elec. Heat P • 2 Pipe Cool Only w/Total Elec. Heat R • 4 Pipe Heat and Cool • • • • • TB155 Wall Series, ACO, Vertical Mnt. TB155 Wall Series, ACO, Horizontal Mtd. Basic 24V Digital Programmable, ACO Basic 24V Non-Programmable, ACO Premium 24V Digital 7-Day Programmable, with Proportional Fan/Valves Option, ACO G • Premium 24 Digital BACnet with Proportional Fan/Valves Option, ACO *** Standing in front of the unit, hand is determined by looking into the air supply and assigning the hand to match the location of the cooling coil connections. 6 International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series RATINGS & LISTINGS AHRI Certification C-ETL US Listing IEC’s Horizontal Series units are IEC’s Horizontal Series units are certified in compliance with listed by ETL. The C-ETL-US listing Air-Conditioning, Heating, and signifies that IEC’s fan coil units Refrigeration Institute (AHRI) industry standard AHRI-440 for have been examined by ETL and room fan coil units. Approved standard ratings are tabulated are in compliance with both the below. U.S. and Canadian applicable 3061627 HEATING AND COOLING EQUIPMENT standards. Standard Ratings Unit Type CHY CPY CXB CBY CHY CPY CXB CBY Unit Cell Nominal Size CFM Cooling Capacity Total MBH Sensible MBH Power Input Watts PSC 02-A 200 6.0 4.4 87 03-A 300 9.0 6.3 85 04-A 400 12.1 8.8 165 06-A 600 17.3 13.0 225 08-A 800 22.6 16.2 235 10-A 1000 27.5 21.0 305 12-A 1200 32.8 25.0 450 02-B 200 6.9 4.3 87 03-B 300 9.8 6.5 85 04-B 400 13.8 9.8 145 06-B 600 19.6 14.3 220 08-B 800 25.5 18.8 235 10-B 1000 31.0 22.0 300 12-B 1200 37.2 27.7 425 NOTES: 1. Ratings are based on 80°F DB and 67°F WB EAT, 45°F EWT, 10°F water temperature rise, high fan speed, motor voltage 115/1/60, and air flow under dry coil conditions. 2. For all application ratings, use IEC’s computer selection program, the quick-selection ratings provided in this catalog, or contact your local IEC representative. 3.For additional information, please consult AHRI’s website at www.ahrinet.org. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 7 Horizontal Series AIR DELIVERY Air Delivery (60 Hz) Model Coil 3 Row CHY 4 Row 3 Row CPY 4 Row 3 Row CBY 4 Row 3 Row CXB 4 Row Unit Size 2 3 4 6 8 10 12 2 3 4 6 8 10 12 2 3 4 6 8 10 12 2 3 4 6 8 10 12 2 3 4 6 8 10 12 2 3 4 6 8 10 12 2 3 4 6 8 10 12 2 3 4 6 8 10 12 CFM@ 0.0 ESP - For Fan Speed Low Med High 221 238 296 275 367 622 726 218 218 279 266 350 612 696 198 221 265 267 356 552 668 194 213 259 275 349 541 635 211 216 303 294 375 536 634 196 210 286 277 364 508 598 203 220 279 308 314 474 684 191 195 263 293 296 447 578 271 291 410 402 700 845 1300 260 264 382 388 670 824 1245 232 270 358 384 642 738 1122 230 258 346 390 622 723 1079 259 270 398 422 678 719 1115 240 262 375 400 652 680 1032 241 273 371 418 625 648 1179 233 256 348 402 595 607 972 357 384 656 733 928 1291 1560 327 337 567 683 902 1208 1480 285 346 523 650 789 1063 1307 276 325 490 628 755 1023 1271 333 353 572 712 821 1098 1313 302 340 523 666 776 1019 1188 306 335 519 640 776 1027 1226 291 320 481 606 728 981 1108 0.05 338 359 610 698 893 1215 1478 312 313 526 652 857 1146 1407 270 325 491 619 752 1008 1241 261 305 462 597 726 971 1204 310 335 544 676 786 1038 1248 277 322 495 628 737 964 1131 290 325 493 602 746 965 1154 271 296 458 565 701 920 1040 0.10 318 333 565 663 856 1140 1394 296 291 488 619 815 1084 1330 254 304 459 586 713 953 1173 245 284 434 563 692 918 1136 287 317 515 637 748 978 1180 253 303 466 588 696 907 1072 271 310 466 564 710 900 1082 250 272 434 525 665 855 971 High Speed CFM @ ESP Indicated 0.15 0.20 0.25 298 308 522 626 818 1068 1305 279 271 452 585 775 1022 1249 237 283 428 549 672 899 1103 228 262 406 525 655 865 1066 265 297 486 597 707 916 1111 232 284 437 547 653 850 1012 249 289 439 526 669 833 1009 229 247 407 486 621 786 901 277 282 479 587 779 997 1213 262 252 418 550 737 959 1164 221 260 397 509 630 846 1031 211 239 377 483 612 813 995 244 277 456 554 664 853 1041 212 264 407 505 608 791 949 225 263 410 487 622 764 935 207 220 378 446 568 713 830 256 258 438 547 738 929 1117 244 234 387 514 700 897 1075 204 237 368 466 586 794 958 193 216 349 438 566 761 922 224 256 427 509 617 790 969 194 243 377 461 560 732 885 199 232 380 447 570 693 861 184 192 347 408 507 635 759 NOTES : 1. Tabled values are standard CFM at sea level, 70°F with dry coil. 8 2. Ratings include factory-installed filter and/or grille, where applicable. 3. Consult factory for 50 Hz applications. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 0.30 234 233 398 506 696 862 1017 224 219 358 476 666 834 982 186 212 338 420 540 742 884 175 192 320 390 515 709 847 204 234 396 462 568 726 896 178 221 347 417 511 672 818 170 195 350 408 513 620 785 161 163 315 369 439 553 686 0.35 212 209 360 464 652 798 913 205 204 331 437 633 771 885 168 187 309 371 492 691 807 155 166 291 337 459 657 771 184 211 365 413 516 660 821 164 199 316 371 459 611 750 139 153 318 368 450 544 710 137 133 280 332 361 466 613 Horizontal Series SOUND DATA Sound Data UNIT SIZE RATING CASING RADIATED 2 DUCTED DISCHARGE CASING RADIATED 3 DUCTED DISCHARGE CASING RADIATED 4 DUCTED DISCHARGE CASING RADIATED 6 DUCTED DISCHARGE CASING RADIATED 8 DUCTED DISCHARGE CASING RADIATED 10 DUCTED DISCHARGE CASING RADIATED 12 DUCTED DISCHARGE SOUND POWER LEVEL, Lw (dB one reference pico watt) FAN SPEED CFM H M L H M L H M 125 Hz 250 Hz 500 Hz 1K Hz 2K Hz 4K Hz 8K Hz 270 170 135 270 170 135 290 205 60 55 53 52 47 46 63 59 54 51 49 52 45 43 54 47 51 44 39 53 45 40 52 44 48 39 34 47 39 33 49 40 43 35 29 46 37 31 44 35 38 31 29 40 31 29 40 31 37 34 34 37 34 34 38 34 A-wgt (dBA) 53 47 44 54 46 42 54 47 L H M L H M L H M L 155 290 205 155 540 360 250 540 360 250 55 59 55 51 70 62 54 64 55 48 42 54 46 42 58 49 42 57 49 42 39 54 47 42 55 46 38 59 51 43 34 51 41 35 52 42 32 55 52 35 29 47 37 31 48 37 30 50 46 30 29 41 31 29 43 32 30 44 36 28 34 38 34 34 39 34 34 39 36 33 43 56 48 43 58 50 42 60 50 43 H 680 65 59 57 52 48 45 42 59 M L H M L H M L H M L H M L H M L 445 330 680 445 330 765 670 410 765 670 410 1105 730 490 1105 730 490 57 52 63 57 53 65 63 55 63 60 52 68 64 59 65 63 58 50 43 58 49 43 61 58 47 61 58 47 64 55 48 62 54 46 47 40 59 50 42 58 55 44 61 58 47 59 51 43 64 56 41 34 56 45 37 54 51 38 58 54 41 55 45 36 60 50 37 29 50 39 30 51 47 34 53 50 36 52 41 31 55 44 33 29 46 33 29 48 44 31 50 46 32 48 37 30 50 38 34 34 42 34 34 45 41 34 46 42 35 45 35 34 46 36 49 43 60 50 44 60 57 46 63 59 48 62 54 47 65 56 H M L H M L 1225 1140 745 1225 1140 745 68 67 59 65 63 56 65 63 54 63 61 54 47 61 59 50 65 63 55 40 57 54 44 60 58 48 33 53 51 40 57 54 43 30 50 47 35 52 50 37 34 45 42 34 47 44 35 48 63 61 52 66 64 54 International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 9 Horizontal Series FAN PERFORMANCE CURVES Unit Size 02 - CPY 0.5 0.45 0.4 ESP (in.W.C.) 0.35 High 0.3 0.25 Med 0.2 Low 0.15 0.1 0.05 0 0 50 100 150 PSC Motor Fan Curve: - 3-Row 4-Row 200 250 300 350 SCFM 5-Row ECM Operating Range: Unit Size 03 - CPY 0.5 0.45 0.4 High ESP (in.W.C.) 0.35 0.3 0.25 Med 0.2 0.15 Low 0.1 0.05 0 0 50 100 PSC Motor Fan Curve: 3-Row 4-Row 10 150 200 5-Row SCFM 250 300 350 400 ECM Operating Range: International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 450 Horizontal Series FAN PERFORMANCE CURVES, Cont’d. Unit Size 04 - CPY 0.5 0.45 0.4 ESP (in.W.C.) 0.35 High 0.3 0.25 Med 0.2 0.15 Low 0.1 0.05 0 100 150 200 250 300 PSC Motor Fan Curve: - 3-Row 4-Row 350 5-Row SCFM 400 450 500 550 600 650 ECM Operating Range: Unit Size 06 - CPY 0.5 0.45 0.4 ESP (in.W.C.) 0.35 High 0.3 0.25 Med 0.2 Low 0.15 0.1 0.05 0 100 150 200 250 PSC Motor Fan Curve: 3-Row 4-Row 300 350 5-Row 400 450 SCFM 500 550 600 650 700 750 ECM Operating Range: International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 11 Horizontal Series FAN PERFORMANCE CURVES, Cont’d. Unit Size 08 - CPY 0.5 0.45 0.4 ESP (in.W.C.) 0.35 High 0.3 0.25 Med 0.2 Low 0.15 0.1 0.05 0 200 250 300 350 400 - 3-Row PSC Motor Fan Curve: 4-Row 450 500 5-Row 550 SCFM 600 650 700 750 800 850 ECM Operating Range: Unit Size 10 - CPY 0.5 0.45 0.4 ESP (in.W.C.) 0.35 High 0.3 Med 0.25 0.2 Low 0.15 0.1 0.05 0 350 400 450 500 550 PSC Motor Fan Curve: - 3-Row 4-Row 12 600 650 700 5-Row 750 800 SCFM 850 900 950 1000 1050 1100 1150 1200 1250 ECM Operating Range: International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series FAN PERFORMANCE CURVES, CONT’D. Unit Size 12 - CPY 0.5 0.45 0.4 ESP (in.W.C.) 0.35 High 0.3 0.25 Med 0.2 0.15 Low 0.1 0.05 0 350 450 550 PSC Motor Fan Curve: - 3-Row 4-Row 650 750 850 5-Row 950 SCFM 1050 1150 1250 1350 1450 1550 ECM Operating Range: International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 13 Horizontal Series ELECTRIC HEATING Electric Resistance Heating Electric Heater Selection Electric heaters are available on IEC Horizontal Series fan coil Voltage kW Unit Size 06 08 02 03 04 - 3.0 - • • • • Individual room controls can be supplied for either manual 0.5 or automatic changeover. 1.0 Auxiliary Electric Heat 1.5 2.0 • • • • 3.0 - • • • • • • • • • • - 2.0 • • • • 4.0 - - - 5.0 - - - 6.0 - - - 8.0 - - Construction 0.5 The heater coils of high-grade resistance wire are supported 1.0 2.0 • • • • 3.0 - • • • • • 4.0 - - - 5.0 - - - 6.0 - - - 8.0 - - 10.0 - - units for the following applications. 0.5 Total Electric Heat 1.0 120 V Total electric heat eliminates the requirement for a boiler. Heating and/or cooling may be available on an individual basis throughout the year. Two-pipe chilled water is used for cooling; and the electric heater is used for heating. Auxiliary electric heat is ideal for tempering room air 208 V between seasons and during the cooling season when chilled water is being circulated. Individual room controls are supplied to provide electric heat only when chilled water is being circulated. During regular heating season, heating is provided by hot water being circulated in the system. by ceramic insulators on plated steel brackets. These heat 1.5 1.5 elements are suspended directly in front of the fan outlet between the blower and the coil. High limit thermal cutouts protect the heater in the event of air failure. There are many 240 V 277 V special applications and control sequences for electric heat. For special applications, please consult the factory. 10 12 - - - • • • • • • • • - - - - • • • • - - - - - • • • • • • • • • • Note 6 • Note 6 • • • • • • • Note 6 - - - - - - - • • • • • • Note 6 • • • • • • Note 6 - - - - - • • • • • • • • • • Note 6 • Note 6 • • • • • • • Note 6 - - - - - - - • • • • • • Note 6 - - - • • • • • • Note 6 • Note 6 NOTES: 1. All heaters are single stage and single phase. 14 - 2. Heaters over 48 Amps are subdivided and fused. 3. Electric Heating Capacities (BTUH) = Heater kW x 3413. 4. Electric Heater Amperage = (Heater kW x 1000)/Applied Voltage) 5. Consult factory for 50 Hz applications. 6. High and medium speed only. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series MOTOR DATA Thermal Overload Protection and ETL Listing All permanently lubricated split-capacitor motors furnished by IEC contain internal thermaloverload protection. The overload automatically resets when the temperature returns to a safe limit. Electronics Testing Laboratories, Inc. approves the motor and thermal overload combination at locked rotor conditions only. Motor Performance Data - CHY, CPY, CXB, CBY Voltage Fan Speed High 115 V 60 Hz Medium 1 Phase Low High 208 V 60 Hz Medium 1 Phase Low High 230 V 60 Hz Medium 1 Phase Low High 277 V 60 Hz Medium 1 Phase Low Unit Size 02 03 04 06 08 10 12 Nominal HP 1/30 1/30 1/12 1/12 1/6 (2) 1/12 (2) 1/6 Amps 0.53 0.83 1.40 1.40 2.50 2.80 5.00 Watts 78 89 144 151 223 286 399 Amps 0.31 0.50 0.70 0.72 1.50 1.40 2.80 Watts 58 62 91 86 166 184 307 Amps 0.27 0.34 0.45 0.45 1.20 0.90 1.20 Watts 44 47 68 60 83 134 166 Amps 0.48 0.48 0.69 0.69 1.30 1.38 2.60 Watts 98 99 120 132 189 245 325 Amps 0.29 0.29 0.43 0.47 0.69 0.94 1.33 Watts 75 75 88 92 109 182 208 Amps 0.15 0.15 0.22 0.24 0.47 0.46 0.94 Watts 49 49 54 55 60 109 120 Amps 0.48 0.48 0.69 0.69 1.30 1.38 2.60 Watts 114 112 137 150 206 281 356 Amps 0.31 0.32 0.45 0.52 0.70 1.00 1.34 Watts 87 86 104 111 128 210 241 Amps 0.15 0.15 0.24 0.28 0.50 0.50 1.00 Watts 57 57 62 65 72 130 143 Amps 0.35 0.35 0.69 0.69 0.91 1.38 1.82 Watts 104 112 143 155 245 288 426 Amps 0.26 0.26 0.43 0.43 0.62 0.80 1.20 Watts 86 91 107 112 152 219 293 Amps 0.16 0.16 0.25 0.35 0.35 0.25 0.66 Watts 55 57 65 67 120 132 234 NOTES: 1. Total unit motor Amps and Watts are shown. 2. Consult factory for 50 Hz applications. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 15 Horizontal Series PHYSICAL DATA CHY - Horizontal Hideaway 4 (102) FLEXIBLE METAL CONDUIT - SEE DIMENSION "J" 4 (102) UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) 1 (25) JUNCTION BOX (REMOTE MOUNT) 7/8 (22) O.D. CONDENSATE DRAIN OPTIONAL 5/8 (16) O.D. TELL-TALE DRAIN CONNECTION, AVAILABLE ON STANDARD AND EXTENDED DRAIN PANS 2 (51) 7-1/3 (187) 6 (152) 1-1/2 (38) 1-1/8 (29) E MTG. HOLES B 2-1/4 (57) RESILIENT MOUNTING GROMMET W/ 3/8 (10) DIA. HOLES (TYP. OF 4) 3 (76) D' OPTIONAL EXTENDED DRAIN PAN A' A TOP VIEW H 3/4 (19) TYP 17-1/2 (445) 1"(25) SUPPLY DUCT COLLAR CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) 16 (406) 8-3/8 (213) AIR VENT 7/8 (22) G F SUPPLY AIR OPTIONAL DRIP LIP SHIPPED LOOSE (NOTE 4) FRONT VIEW RIGHT SIDE VIEW Dimensions - Inches (Millimeters) Unit Model A CHY02 CHY03 CHY04 CHY06 CHY08 CHY10 CHY12 21-1/4 (540) 25-1/4 (641) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) A’ B 31-1/4 (794) 16 (406) 36-1/4 (921) 20 (508) 43-1/4 (1099) 26 (660) 43-1/4 (1099) 31 (787) 57-1/4 (1454) 38 (965) 65-1/4 (1657) 52 (1321) 75-1/4 (1911) 60 (1524) D’ E 13 (330) 14 (356) 15 (381) 10 (254) 17 (432) 11 (279) 13 (330) 18-1/4 (464) 22-1/4 (565) 28-1/4 (718) 33-1/4 (845) 40-1/4 (1022) 54-1/4 (1378) 62-1/4 (1581) F Quantity/Unit G H J Blower Motor Unit Weight* 1 1 2 2 2 4 4 1 1 1 1 1 2 2 36 39 49 59 64 95 107 6-1/4 (159) 8-3/4 (222) 19-3/4 (502) 38 (965) 6-1/4 (159) 8-3/4 (222) 23-3/4 (603) 38 (965) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 38 (965) 7-1/2 (191) 10 (254) 34-3/4 (883) 38 (965) 7-1/2 (191) 10 (254) 41-3/4 (1060) 38 (965) 7-1/2 (191) 10 (254) 55-3/4 (1416) 60 (1524) 7-1/2 (191) 10 (254) 63-3/4 (1619) 65 (1651) NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 16 1. 2. 3. 4. 5. 6. 7. 8. RH shown, LH opposite. Optional drip lip not required with optional extended drain pan. All dimensions are +/- 1/4" (6). Drip lip recommended. Product specifications are subject to change without notice. Control box size and position may vary (consult factory). Dimension “G” represents maximum on lowest end of sloped drain pan. Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PHYSICAL DATA, Cont’d. CHY - Horizontal Hideaway with Electric Heat UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) FLEXIBLE METAL CONDUIT - SEE DIMENSION "J" CONTROL BOX (REMOTE MOUNT) 5-3/8 (137) STD. STRIP HEATER HIGH LIMIT ELECTRIC STRIP HEATER ELEMENT 1 (25) 6 (152) STD. OPTIONAL 5/8 (16) O.D. TELL-TALE DRAIN CONNECTION, AVAILABLE ON STANDARD AND EXTENDED DRAIN PANS 2 (51) 7/8 (22) O.D. CONDENSATE DRAIN 6 (152) 7-1/3 (187) RESILIENT MOUNTING GROMMET W/ 3/8 (10) DIA. HOLES (TYP. OF 4) 1-1/2 (38) 1-1/8 (29) 2-1/4 (64) E MTG. HOLES B 3 (76) D' OPTIONAL EXTENDED DRAIN PAN A' A TOP VIEW 21-1/2 (546) H 3/4 (19) TYP CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) 12-3/8 (314) 1"(25) SUPPLY DUCT COLLAR 7/8 (22) G F AIR VENT SUPPLY AIR OPTIONAL DRIP LIP SHIPPED LOOSE (NOTE 4) 16 (406) FRONT VIEW RIGHT SIDE VIEW Dimensions - Inches (Millimeters) Unit Model A A’ B CHY02 CHY03 CHY04 CHY06 CHY08 CHY10 CHY12 21-1/4 (540) 25-1/4 (641) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) 75-1/4 (1911) 16 (406) 20 (508) 26 (660) 31 (787) 38 (965) 52 (1321) 60 (1524) D’ E F Quantity/Unit G H J 13 (330) 18-1/4 (464) 6-1/4 (159) 8-3/4 (222) 19-3/4 (502) 38 (965) 14 (356) 22-1/4 (565) 6-1/4 (159) 8-3/4 (222) 23-3/4 (603) 38 (965) 15 (381) 28-1/4 (718) 6-1/4 (159) 8-3/4 (222) 29-3/4 (756) 38 (965) 10 (254) 33-1/4 (845) 7-1/2 (191) 10 (254) 34-3/4 (883) 38 (965) 17 (432) 40-1/4 (1022) 7-1/2 (191) 10 (254) 41-3/4 (1060) 38 (965) 11 (279) 54-1/4 (1378) 7-1/2 (191) 10 (254) 55-3/4 (1416) 60 (1524) 13 (330) 62-1/4 (1581) 7-1/2 (191) 10 (254) 63-3/4 (1619) 65 (1651) Blower Motor Unit Weight* 1 1 2 2 2 4 4 1 1 1 1 1 2 2 38 41 51 61 66 97 109 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Optional drip lip not required with optional extended drain pan. All dimensions are +/- 1/4" (6). Drip lip recommended. Product specifications are subject to change without notice. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 17 Horizontal Series PHYSICAL DATA, Cont’d. CPY - Horizontal Hideaway with Plenum 1-1/2 (38) H REAR MTG. HOLES INSULATED UNIT LABEL AND PLENUM WIRING DIAGRAM JUNCTION (SEE NOTE 6) BOX 3 (76) 3-1/4 (83) 1 (25) 7/8 (22) O.D. CONDENSATE DRAIN 4 (102) 15-1/4 (387) 1-1/2 (38) OPTIONAL 5/8 (16) O.D. TELL-TALE DRAIN CONNECTION, AVAILABLE ON STANDARD AND EXTENDED DRAIN PANS 1-1/8 (29) 2-1/4 (57) 2 (51) RESILIENT MOUNTING GROMMET W/ 3/8 (10) DIA. HOLES (TYP. OF 4) C MTG. HOLES B 1"(25) FILTER 7-1/3 (187) RETURN AIR A' BOTTOM ACCESS PANEL 3 (76) FILTER RETAINER CLIP FILTER REMOVAL OPTIONAL REAR RETURN TOP VIEW E 3/4 (19) TYP 1"(25) RETURN DUCT COLLAR OPTIONAL EXTENDED DRAIN PAN D' 1"(25) SUPPLY DUCT COLLAR 7/8 (22) CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) 10-1/2 (267) G OPTIONAL DRIP LIP SHIPPED LOOSE (NOTE 4) F 11-3/8 (289) AIR VENT SUPPLY AIR REAR ACCESS PANEL 1"(25) FILTER 16 (406) A 20 (508) 19 (483) RETURN AIR FILTER REMOVAL RIGHT SIDE VIEW FRONT VIEW Dimensions - Inches (Millimeters) Unit Model A A’ B C D’ E CPY02 CPY03 CPY04 CPY06 CPY08 CPY10 CPY12 21-1/4 (540) 25-1/4 (641) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) 75-1/4 (1911) 16 (406) 20 (508) 26 (660) 31 (787) 38 (965) 52 (1321) 60 (1524) 18-1/4 (464) 22-1/4 (565) 28-1/4 (718) 33-1/4 (845) 40-1/4 (1022) 54-1/4 (1378) 62-1/4 (1581) 13 (330) 14 (356) 15 (381) 10 (254) 17 (432) 11 (279) 13 (330) 19-3/4 (502) 23-3/4 (603) 29-3/4 (756) 34-3/4 (883) 41-3/4 (1060) 55-3/4 (1416) 63-3/4 (1619) Quantity/Unit F G H 6-1/4 (159) 8-3/4 (222) 15-3/8 (391) 6-1/4 (159) 8-3/4 (222) 19-3/8 (883) 6-1/4 (159) 8-3/4 (222) 25-3/8 (645) 7-1/2 (190) 10 (254) 30-3/8 (772) 7-1/2 (190) 10 (254) 37-3/8 (949) 7-1/2 (190) 10 (254) 51-3/8 (1305) 7-1/2 (190) 10 (254) 59-3/8 (1508) Unit Blower Motor Weight* 1 1 2 2 2 4 4 1 1 1 1 1 2 2 55 60 70 82 95 135 154 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 18 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Optional drip lip not required with optional extended drain pan. All dimensions are +/- 1/4" (6). Drip lip recommended. Product specifications are subject to change without notice. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PHYSICAL DATA, Cont’d. CPY - Horizontal Hideaway with Plenum with Electric Heat H REAR MTG. HOLES UNIT LABEL AND INSULATED WIRING DIAGRAM PLENUM (SEE NOTE 7) CONTROL BOX 5-3/8 (137) STD. OPTIONAL 5/8 (16) O.D. TELL-TALE DRAIN CONNECTION, AVAILABLE ON STANDARD AND EXTENDED DRAIN PANS 1-1/2 (38) 3-1/4 (83) 2 (51) ELECTRIC STRIP HEATER ELEMENT 1 (25) 6 (152) STD. 19-1/4 (489) 7/8 (22) O.D. CONDENSATION DRAIN 1-1/2 (38) C FRONT MTG. HOLES B A A' FILTER RETAINER CLIP FILTER REMOVAL 3 (76) OPTIONAL REAR RETURN 10-1/2 (267) 16 (406) 24 (610) 23 (584) 1"(25) SUPPLY DUCT COLLAR 7/8 (22) CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) RESILIENT MOUNTING GROMMET W/ 3/8 (10) DIA. HOLES (TYP. OF 4) ELECTRICAL KNOCKOUTS IN TOP & BOTTOM OF CONTROL BOX 1"(25) RETURN DUCT COLLAR BOTTOM ACCESS PANEL TOP VIEW 3/4 3/4 (19) (19) TYP RETURN AIR OPTIONAL EXTENDED DRAIN PAN D' STRIP HEATER HIGH LIMIT 1-1/8 (29) 2-1/4 (57) 1"(25) FILTER 7-1/3 (187) G OPTIONAL DRIP LIP SHIPPED LOOSE (NOTE 5) 11-3/8 (289) AIR VENT SUPPLY F AIR REAR ACCESS PANEL 1"(25) FILTER RETURN AIR FRONT VIEW FILTER REMOVAL RIGHT SIDE VIEW Dimensions - Inches (Millimeters) Unit Model A A’ B C D’ E CPY02 CPY03 CPY04 CPY06 CPY08 CPY10 CPY12 21-1/4 (540) 25-1/4 (641) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) 31-1/4 (794) 36-1/4 (921) 43-1/4 (1099) 43-1/4 (1099) 57-1/4 (1454) 65-1/4 (1657) 75-1/4 (1911) 16 (406) 20 (508) 26 (660) 31 (787) 38 (965) 52 (1321) 60 (1524) 18-1/4 (464) 22-1/4 (565) 28-1/4 (718) 33-1/4 (845) 40-1/4 (1022) 54-1/4 (1378) 62-1/4 (1581) 13 (330) 14 (356) 15 (381) 13 (330) 17 (432) 11 (279) 13 (330) 19-3/4 (502) 23-3/4 (603) 29-3/4 (756) 34-3/4 (883) 41-3/4 (1060) 55-3/4 (1416) 63-3/4 (1619) Quantity/Unit F G H 6-1/4 (159) 8-3/4 (222) 15-3/8 (391) 6-1/4 (159) 8-3/4 (222) 19-3/8 (883) 6-1/4 (159) 8-3/4 (222) 25-3/8 (645) 7-1/2 (190) 10 (254) 30-3/8 (772) 7-1/2 (190) 10 (254) 37-3/8 (949) 7-1/2 (190) 10 (254) 51-3/8 (1305) 7-1/2 (190) 10 (254) 59-3/8 (1508) Unit Blower Motor Weight* 1 1 2 2 2 4 4 1 1 1 1 1 2 2 57 62 72 84 97 137 156 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Optional drip lip not required with optional extended drain pan. All dimensions are +/- 1/4" (6). Product specifications are subject to change without notice. Drip lip recommended. Threaded fittings must be field tightened and leak tested. Control box size and position may vary (consult factory). Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 19 Horizontal Series PHYSICAL DATA, Cont’d. CBY - Horizontal Telescoping Hideaway 1 (25) 1-1/2 (38) UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) JUNCTION BOX OPTIONAL "L" SHAPED DRIP 26 (660) 1 (25) CHILLED/HOT WATER SUPPLY & RETURN CONNECTION (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) RESILIENT MOUNTING GROMMETS WITH 3/8 (10) 7/8 (22) DIA. HOLE KNOCKOUT (TYP. OF 4) 20-3/4 (527) 1-1/2 (38) 1 (25) E 6-1/8 (156) 1 (25) TOP VIEW 1-1/2 (38) KNOCKOUT (TYPICAL) PARTIAL REAR VIEW (TYPICAL BOTH SIDES) 24 (610) 1-1/2 (38) TYP 1-1/2 (38) A 6-1/8 (156) B C 20-3/4 (527) F OPTIONAL DUCTED REAR RETURN AIR VENT 1-1/4 (32) 11-1/4 12 (305) (286) MIN. 14 (356) MAX. 1-1/2 (38) 6 (152) SUPPLY AIR 1"(25) SUPPLY DUCT COLLAR 7/8 (22) O.D. CONDENSATE DRAIN CONNECTION D FRONT VIEW RIGHT SIDE VIEW Dimensions - Inches (Millimeters) C D Unit Model A B CBY02 CBY03 CBY04 CBY06 CBY08 CBY10 CBY12 35 (889) 35 (889) 41 (1041) 53 (1346) 53 (1346) 75 (1905) 75 (1905) 16 (406) 20 (508) 26 (660) 31 (787) 38 (965) 52 (1321) 60 (1524) 12-3/4 (324) 8-3/4 (222) 8-3/4 (222) 15-3/4 (400) 8-3/4 (222) 16-3/4 (425) 8-3/4 (222) RETURN AIR 1 (25) HINGED BOTTOM STAMPED RETURN RETURN AIR PANEL AIR GRILLE & 1"(25) FILTER 37 (940) 37 (940) 43 (1092) 55 (1397) 55 (1397) 77 (1956) 77 (1956) E F 32 (813) 32 (813) 38 (965) 50 (1270) 50 (1270) 72 (1829) 72 (1829) 6 (152) 6 (152) 6 (152) 7 (178) 7 (178) 7 (178) 7 (178) Quantity/Unit Blower Motor 1 1 2 2 2 4 4 1 1 1 1 1 2 2 Unit Weight* 115 120 135 150 155 227 241 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 20 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Internal factory valve packages and drains may not align w/cabinet knockouts. All dimensions are +/- 1/4" (6). Product specifications are subject to change without notice. Drip lip required for units with valves. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PHYSICAL DATA, Cont’d. CBY - Horizontal Telescoping Hideaway with Electric Heat 1 (25) 1-1/2 (38) 26 (660) UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) ELECTRIC STRIP HEATER ELEMENT OPTIONAL "L" SHAPED DRIP LIP, SHIPPED LOOSE (NOTE 5) CHILLED/HOT WATER SUPPLY & RETURN CONNECTION (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) STRIP CONTROL A HEATER BOX HIGH LIMIT 20-3/4 (527) RESILIENT MOUNTING GROMMETS WITH 3/8 (10) DIA. HOLE (TYP. OF 4) 1 (25)1-1/2 (38) E 1 (25) 6-1/8 (156) 7/8 (22) KNOCKOUT 1-1/2 (38) KNOCKOUT (TYPICAL) 1 (25) TOP VIEW PARTIAL REAR VIEW (TYPICAL BOTH SIDES) 24 (610) 1-1/2 (38) TYP 1-1/2 (38) A 6-1/8 (156) B C 20-3/4 (527) AIR VENT 1-1/4 (32) 11-1/4 12(305) (286) MIN. 14(356) MAX. F SUPPLY 6 (152) AIR 1 (25) 1"(25) SUPPLY DUCT COLLAR FRONT VIEW RIGHT SIDE VIEW Dimensions - Inches (Millimeters) C D Unit Model A B CBY02 CBY03 CBY04 CBY06 CBY08 CBY10 CBY12 35 (889) 35 (889) 41 (1041) 53 (1346) 53 (1346) 75 (1905) 75 (1905) 16 (406) 20 (508) 26 (660) 31 (787) 38 (965) 52 (1321) 60 (1524) HINGED STAMPED BOTTOM RETURN RETURN RETURN AIR AIR GRILLE & AIR PANEL 1"(25) FILTER 7/8 (22) O.D. CONDENSATE DRAIN CONNECTION D 12-3/4 (324) 8-3/4 (222) 8-3/4 (222) 15-3/4 (400) 8-3/4 (222) 16-3/4 (425) 8-3/4 (222) 1-1/2 (38) OPTIONAL DUCTED REAR RETURN 37 (940) 37 (940) 43 (1092) 55 (1397) 55 (1397) 77 (1956) 77 (1956) E F 32 (813) 32 (813) 38 (965) 50 (1270) 50 (1270) 72 (1829) 72 (1829) 6 (152) 6 (152) 6 (152) 7 (178) 7 (178) 7 (178) 7 (178) Quantity/Unit Blower Motor 1 1 2 2 2 4 4 1 1 1 1 1 2 2 Unit Weight* 117 122 137 152 157 229 243 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Optional drip lip not required with optional extended drain pan. All dimensions are +/- 1/4" (6). Product specifications are subject to change without notice. Drip lip required for units with valves. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 21 Horizontal Series PHYSICAL DATA, Cont’d. CBY - Horizontal Telescoping Hideaway with Bottom Supply 1 (25) 1-1/2 (38) UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) JUNCTION BOX OPTIONAL "L" SHAPED DRIP LIP, SHIPPED LOOSE (NOTE 5) 36 (914) CHILLED/HOT WATER SUPPLY & RETURN CONNECTION (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) 30-3/4 (781) RESILIENT MOUNTING GROMMETS WITH 3/8 (10) DIA. HOLE (TYP. OF 4) 1 (25) 1-1/2 (38) 1-1/2 (38) 1-1/2 (38) 1 (25) E 1 (25) TOP VIEW PARTIAL REAR VIEW (TYPICAL BOTH SIDES) 1-1/2 (38) A 1-1/2 (38) 7/8 (22) KNOCKOUT 1-1/2 (38) KNOCKOUT (TYPICAL) 30-3/4 (781) 1-1/2 (38) 34 (864) 1-1/2 (38) OPTIONAL DUCTED REAR RETURN AIR VENT 11-1/4 (286) 12"(305) MIN. 14"(356) MAX. 6 (152) 1 (25) STAMPED SUPPLY AIR GRILLE D SUPPLY 7/8 (22) O.D. CONDENSATE AIR 6 DRAIN (152) CONNECTION FRONT VIEW Unit Model CBY02 CBY03 CBY04 CBY06 CBY08 CBY10 CBY12 A 35 (889) 35 (889) 41 (1041) 53 (1346) 53 (1346) 75 (1905) 75 (1905) RIGHT SIDE VIEW Dimensions - Inches (Millimeters) D E 37 (940) 37 (940) 43 (1092) 55 (1397) 55 (1397) 77 (1956) 77 (1956) RETURN AIR 32 (813) 32 (813) 38 (965) 50 (1270) 50 (1270) 72 (1829) 72 (1829) F 6 (152) 6 (152) 6 (152) 7 (178) 7 (178) 7 (178) 7 (178) Quantity/Unit Blower Motor 1 1 2 2 2 4 4 1 1 1 1 1 2 2 HINGED BOTTOM RETURN AIR PANEL STAMPED RETURN AIR GRILLE & 1"(25) FILTER Unit Weight* 115 120 135 150 155 227 241 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 22 1. RH shown, LH opposite. 2. Internal factory valve packages and drains may not align w/cabinet knockouts. 3. All dimensions are +/- 1/4" (6). 4. Product specifications are subject to change without notice. 5. Drip lip required for units with valves. 6. Control box size and position may vary (consult factory). 7.Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PHYSICAL DATA, Cont’d. CBY - Horizontal Telescoping Hideaway with Bottom Supply with Electric Heat 1 (25) 1-1/2 (38) UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) ELECTRIC STRIP HEATER ELEMENT CONTROL BOX STRIP HEATER HIGH LIMIT OPTIONAL "L" SHAPED DRIP LIP, SHIPPED LOOSE (NOTE 5) CHILLED/HOT WATER SUPPLY & RETURN CONNECTION (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) 30-3/4 36 (781) (914) RESILIENT MOUNTING GROMMETS WITH 3/8 (10) DIA. HOLE (TYP. OF 4) 1 (25) 1-1/2 (38) 1-1/2 (38) 1 (25) E TOP VIEW 1-1/2 (38) KNOCKOUT (TYPICAL) PARTIAL REAR VIEW 1-1/2 (38) 1 (25) (TYPICAL BOTH SIDES) 34 (864) 1-1/2 (38) A 1-1/2 (38) TYP 7/8 (22) KNOCKOUT 30-3/4 (781) 1-1/2 (38) AIR VENT OPTIONAL DUCTED REAR RETURN 11-1/4 (286) 6 (152) 12"(305) MIN. 14"(356) MAX. STAMPED SUPPLY AIR GRILLE D FRONT VIEW Unit Model CBY02 CBY03 CBY04 CBY06 CBY08 CBY10 CBY12 A Dimensions - Inches (Millimeters) D E 35 (889) 35 (889) 41 (1041) 53 (1346) 53 (1346) 75 (1905) 75 (1905) 37 (940) 37 (940) 43 (1092) 55 (1397) 55 (1397) 77 (1956) 77 (1956) 32 (813) 32 (813) 38 (965) 50 (1270) 50 (1270) 72 (1829) 72 (1829) SUPPLY AIR 6 (152) 7/8 (22) O.D. CONDENSATE DRAIN CONNECTION RETURN AIR RIGHT SIDE VIEW Quantity/Unit Blower Motor 1 1 2 2 2 4 4 1 1 1 1 1 2 2 1 (25) HINGED BOTTOM RETURN AIR PANEL STAMPED RETURN AIR GRILLE & 1"(25) FILTER Unit Weight* 117 122 137 152 157 229 243 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Internal factory valve packages and drains may not align w/cabinet knockouts. All dimensions are +/- 1/4" (6). Product specifications are subject to change without notice. Drip lip required for units with valves. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 23 Horizontal Series PHYSICAL DATA, CONT’D. CXB - Horizontal Cabinet OPTIONAL STAMPED RETURN AIR GRILLE & 1" (25) FILTER UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) JUNCTION BOX 3 1/2 (89) OPTIONAL "L" SHAPED DRIP LIP, SHIPPED LOOSE (NOTE 5) 7/8 (22) KNOCKOUT (TYP. OF 2) 18 (457) 2 (51) 2 (51) E 2 (51) A TOP VIEW C PARTIAL REAR VIEW CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) (TYPICAL BOTH SIDES) C B STANDARD STAMPED SUPPLY AIR GRILLE RESILIENT MOUNTING GROMMETS WITH 3/8" (10) DIA. HOLE (TYP. OF 4) OPTIONAL RETURN 5-3/4 AIR (146) LOCATION SUPPLY F AIR APPROX. 2 REF. (51) REMOVABLE HINGED R.A./ACCESS PANEL FRONT VIEW CXB02 CXB03 CXB04 CXB06 CXB08 CXB10 CXB12 23-1/2 (597) 7/8" (22) O.D. CONDENSATE DRAIN CONNECTION AIR VENT 1-1/2 (38) G Unit Model 1-1/2 (38) KNOCKOUT (TYP. OF 5) STANDARD STAMPED RETURN AIR GRILLE & 1" (25) FILTER RETURN AIR RIGHT SIDE VIEW Dimensions - Inches (Millimeters) Quantity/Unit A B C E F G Blower Motor Unit Weight* 38 (965) 42 (1067) 48 (1219) 53 (1346) 60 (1524) 74 (1880) 82 (2083) 17-1/8 (435) 21-1/2 (546) 25-7/8 (657) 34-5/8 (879) 39 (991) 52-1/8 (1324) 60-7/8 (1546) 10-7/16 (265) 10-1/4 (260) 11-1/16 (281) 9-3/16 (233) 10-1/2 (267) 10-15/16 (262) 10-9/16 (268) 34 (864) 38 (965) 44 (1118) 49 (1245) 56 (1422) 70 (1778) 78 (1981) 5-3/4 (146) 5-3/4 (146) 5-3/4 (146) 6-3/4 (171) 6-3/4 (171) 6-3/4 (171) 6-3/4 (171) 11 (279) 11 (279) 11 (279) 12 (305) 12 (305) 12 (305) 12 (305) 1 1 2 2 2 4 4 1 1 1 1 1 2 2 98 118 126 168 176 215 245 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 24 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Internal factory valve packages and drains may not align w/cabinet knockouts. All dimensions are +/- 1/4" (6). Product specifications are subject to change without notice. Drip lip required for units with valves. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PHYSICAL DATA, Cont’d. CXB - Horizontal Cabinet with optional Electric Heat UNIT LABEL AND WIRING DIAGRAM (SEE NOTE 6) CONTROL BOX 3-1/2 (89) OPTIONAL STAMPED RETURN AIR GRILLE & 1" (25) FILTER OPTIONAL "L" SHAPED DRIP LIP, SHIPPED LOOSE (NOTE 5) 1-1/2 (38) KNOCKOUT (TYP. OF 5) OPTIONAL ELECTRIC STRIP HEATER ELEMENT 7/8 (22) KNOCKOUT (TYP. OF 2) 7/8 (22) O.D. CONDENSATE DRAIN CONNECTION 18 (457) 2 (51) 2 (51) 2 (51) E A TOP VIEW CHILLED/HOT WATER SUPPLY & RETURN CONNECTIONS (SEE SUPPLEMENTAL DRAWING FOR COIL STUBOUT LOCATIONS) PARTIAL REAR VIEW (TYPICAL BOTH SIDES) 23-1/2 (597) C C B G STANDARD STAMPED SUPPLY AIR GRILLE FRONT VIEW Unit Model CXB02 CXB03 CXB04 CXB06 CXB08 CXB10 CXB12 AIR VENT 1-1/2 (38) RESILIENT MOUNTING GROMMETS WITH 3/8 (10) DIA. HOLE (TYP. OF 4) F OPTIONAL RETURN 5-3/4 AIR LOCATION (146) SUPPLY AIR APPROX. 2 REF. (51) REMOVABLE HINGED R.A./ACCESS PANEL STANDARD STAMPED RETURN AIR GRILLE & 1"(25) FILTER RETURN AIR RIGHT SIDE VIEW Dimensions - Inches (Millimeters) Quantity/Unit A B C E F G Blower Motor Unit Weight* 38 (965) 42 (1067) 48 (1219) 53 (1346) 60 (1524) 74 (1880) 82 (2083) 17-1/8 (435) 21-1/2 (546) 25-7/8 (657) 34-5/8 (879) 39 (991) 52-1/8 (1324) 60-7/8 (1546) 10-7/16 (265) 10-1/4 (260) 11-1/16 (281) 9-3/16 (233) 10-1/2 (267) 10-15/16 (262) 10-9/16 (268) 34 (864) 38 (965) 44 (1118) 49 (1245) 56 (1422) 70 (1778) 78 (1981) 5-3/4 (146) 5-3/4 (146) 5-3/4 (146) 6-3/4 (171) 6-3/4 (171) 6-3/4 (171) 6-3/4 (171) 11 (279) 11 (279) 11 (279) 12 (305) 12 (305) 12 (305) 12 (305) 1 1 2 2 2 4 4 1 1 1 1 1 2 2 100 120 128 170 178 217 247 NOTES: *Unit weights (shown in pounds) are based on dry coils, minimum rows and exclude packaging, valves or other components. 1. 2. 3. 4. 5. 6. 7. RH shown, LH opposite. Internal factory valve packages and drains may not align w/cabinet knockouts. All dimensions are +/- 1/4" (6). Product specifications are subject to change without notice. Drip lip required for units with valves. Control box size and position may vary (consult factory). Threaded fittings must be field tightened and leak tested. Drawing is not to scale and is provided for reference only. Dimensions may vary with options ordered. Consult IEC web site for up to date drawings. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 25 Horizontal Series STANDARD FEATURES & OPTIONS Standard Factory Installed Option Field Installed Option Factory Special Quote X X (Bottom) – X (Rear) – – – – – X – – X – – – X – X X – X X X – – – – – – – – – – – – – – – X X – – X – – – – X – – – – – X – X X – – X – – – – – – v X – – – X X – – – – X – X – – – X X – – – – – – X – – – – X X X – – – – – X – – X – – – X – – X – – – – X – Double Deflection, Aluminum Finish Supply Grille – X (CXB Double Deflection, Integral Supply Grille - painted Stamped Return Grille (CBY, CXB) – X X (CXB) – Hinged Bar-Type, Aluminum-finish Return Grille with Throwaway Filter - F.O. – – Controls Service Switch with Lockout Tabs Single Point Power Connection Incoming Power Fusing 24 V Controls Condensate Overflow Switch 3-Speed Switch Thermostats Custom Control (DDC) – X (CHY, CPY, CBY) – – X (CHY, CPY, CBY) – X (CHY, CPY, CBY) – – X (CHY, CPY, CBY) – – – – – X – – X X X X X – – X – – – – – X X – – – – – – – – X Features And Options Air Flow Arrangement Front Supply/Rear Return (CHY) Front Supply/Rear or Bottom Return (CPY, CBY, CXB) Coils 2 Rows 2-Pipe (CHY, CPY, CBY, CXB) 3 Rows 2-Pipe (CHY, CPY, CBY, CXB) 4 Rows 2-Pipe (CHY, CPY, CBY, CXB) 3/1, 3/2, 4/1 Rows 4-Pipe (CHY, CPY, CBY, CXB) Manual Air Vent Automatic Air Vent DX Coils Steam Coils Connection Right or Left (Same End) Right or Left (Opposite End) Drain Pan Galvanized Internally Coated with 2-part closed Cell Foam Stainless Steel Externally Coated Drip Lip (recommended with motorized valves) Extended Drain Pans (CHY, CPY) Secondary Drain Connection Fin Material Aluminum with Galvanized End Sheets Copper with Stainless End Sheets & Bottom Coil Baffle Nichrome Wire Strip Electric Heater (Total and Auxiliary) Filters 1" Throwaway non-woven synthetic filter 1" Permanent 1" Pleated MERV 8 Insulation 1/2" Standard Fiberglass 1/2" Premium IAQ Fiberglass 1/2" Foil Face 1/4" Closed Cell Motor Type PSC Motors with Quick Connect Plug Motor Voltage 120/1/60 3-Speed 208/230/277/1/60 3-Speed (Optional Voltage) Supply/Return Air Grilles Louvered Stamped Supply Grille (CXB) 26 International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series STANDARD FEATURES & OPTIONS, Cont’d. As detailed in the table on page 27, we offer a control for most of the customer needs. Additional controls and devices are available to meet even the most demanding operating logic. Condensate High Level Switch This switch shuts down the unit when the water level in the drain pan reaches an unsafe level. Building code changes in much of the country now require this type of device. Three-speed Fan Control All of our basic control schemes utilize a 2- or 3-speed switch to modulate the cooling output, to maximize the percentage of latent heat removal, and to further minimize the sound level when maximum cooling or heating Service Switches We offer concealed service switches for use by maintenance and service personnel to shut off the power while working on the unit. performance is not required. Fusing Low Voltage Control (24 V) We offer incoming power fusing for all units as well as A low voltage control is available with all of our control schemes. blower motor and control sub-fusing for units that use electric heat. The blower motor and control sub-fusing (single power source wiring) is required when single source power with electric heat is specified. Control Packages Vertical Wall Series 155 24 V Programmable and Non-Programmable Digital Series International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 27 Horizontal Series STANDARD FEATURES & OPTIONS, Cont’d. Control Package Applications Unit Type Control Option – Manual Fan System Type Changeover Type Vertical and Horizontal Wall Series 155 Manual1 Heat Only Cool Only None None None Manual Automatic Manual Automatic Manual Automatic Manual Automatic – Heat/Cool 2-Pipe Valve Cycle* Heat/Cool with Auxiliary Electric Heat Cool with Total Electric Heat 4-Pipe Heat/Cool 24 V Programmable and Non-Programmable Digital Series – – – – – NOTE: 1. Fan switch only; no thermostat. Thermostat Features All listed controls include fan switching. 24 V, 115 V, 208 V, 240 V, 277 V Remote Wall Mounted Manual Fan Switch Operation Auto Fan Speed Control Continuous 3-Speed Fan Cycling Fan O.A. Damper Signal Remote Temperature Sensor Adjustable Operating Range Touch Pad/Digital Display Local Temperature Set-Back Water Temperature Purge Cycle Pipe Sensor Control Type1 Vertical and Horizontal Wall Series 155 N/A N/A Opt Kit N/A N/A N/A N/A 24 V Digital Series 24 V only Opt NOTES: 1. Control packages with valve cycle control are continuous fan operation only. 2. All wall-mount control packages are shipped loose for field installation. (Boxes, tile rings, plaster rings, etc. are not provided.) 3. Aquastats are included in control packages, as required. Control Options • • • • • 28 24 V control packages Unit-mounted fan switches (Special Quote) Single power source wiring (motor/control fusing) Incoming power fusing Service switches • • • • Minimum room temperature thermostats (Special Quote) Low voltage remote shutdown relays (Special Quote) Fan and valve cycle applications (Special Quote) Thermostats available with large letter print for handicap applications (Special Quote) • DX coil applications International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series STANDARD FEATURES & OPTIONS, Cont’d. Supply Air Grilles Return Air Filter Grilles Unit Size Nominal CFM Recommended Grille Size Inches (Millimeters) Unit Size Nominal CFM Recommended Grille Size Inches (Millimeters) 02 200 16" x 6" (406 x 152) 02 200 24" x 10" (610 x 254) 03 300 20" x 6" (508 x 152) 03 300 28" x 10" (711 x 254) 04 400 26" x 6" (660 x 152) 04 400 32" x 10" (813 x 254) 06 600 30" x 6" (762 x 152) 06 600 42" x 10" (1067 x 254) 08 800 38" x 6" (965 x 152) 08 800 42" x 10" (1067 x 254) 10 1000 52" x 6" (1320 x 152) 10 1000 54" x 10" (1372 x 254) 12 1200 60" x 6" (1524 x 152) 12 1200 64" x 10" (1626 x 254) NOTES: 1. Refer to Physical Data, pages 13 through 26 for actual NOTES: 1. Refer to Physical Data, pages 13 through 26 for actual unit supply air opening dimensions. 2. Field-furnished duct transitions may be required. Optional Double Deflection, Aluminum-finish Supply Grille (Optional special ship separate for models CHY, CPY, and CBY. Consult factory for details.) unit return air opening dimensions. 2. Field-furnished duct transitions may be required. Optional Hinged, Bar-type, Aluminum-finish Return Grille with Throwaway Filter (Optional special ship separate for models CHY, CPY, and CBY. Consult factory for details.) Optional Double-deflection, Integral Supply Grille Painted to Match Color of Unit International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 29 Horizontal Series STANDARD FEATURES & OPTIONS, Cont’d. Nominal Filter Sizes All cabinet model units (except CH) have non-woven synthetic throwaway filters furnished as standard equipment. Cleanable and pleated filters are optional. Nominal One-Inch Filter Size - Inches (Millimeters) Unit Size CHY (Note 1) CPY CBY Bottom Return Stamped CBY Rear Return Stamped CXB Bottom Return Stamped CXB Rear Return Stamped CXB Rear Return Ducted 02 10" x 24" (254 x 610) 10" x 18" (254 x 457) 10" x 28" (254 x 711) 7" x 21" (178 x 533) 10" x 23-1/2" (254 x 597) 8" x 23-1/2" (203 x 597) 8" x 23-1/2" (203 x 597) 03 10" x 28" (254 x 711) 10" x 22" (254 x 559) 10" x 28" (254 x 711) 7" x 21" (178 x 533) 10" x 28" (254 x 711) 8" x 28" (203 x 711) 8" x 28" (203 x 711) 04 10" x 32" (254 x 813) 10" x 28" (254 x 711) 10" x 33" (254 x 838) 7" x 27" (178 x 533) 10" x 32-1/2" (254 x 826) 8" x 32-1/2" (203 x 826) 8" x 32-1/2" (203 x 826) 06 10" x 42" (254 x 1067) 10" x 33" (254 x 838) 10" x 45" (254 x 1143) 7" x 38" (178 x 965) 10" x 37" (254 x 940) 8" x 37" (203 x 940) 8" x 37" (203 x 940) 08 10" x 42" (254 x 1067) 10" x 40" (254 x 1016) 10" x 45" (254 x 1626) 7" x 38" (178 x 965) 10" x 41" (254 x 1041) 8" x 41" (203 x 1041) 8" x 41" (203 x 1041) 10 10" x 54" (254 x 1372) 10" x 54" (254 x 1372) 10" x 62" (254 x 1575) 7" x 52" (178 x 1321) 10" x 54-1/2" (254 x 1384) 8" x 54-1/2" (203 x 1384) 8" x 54-1/2" (203 x 1384) 12 10" x 64" (254 x 1626) 10" x 62" (254 x 1575) 10" x 62" (254 x 1575) 7" x 52" (178 x 1321) 10" x 63" (254 x 1600) 8" x 63" (203 x 1600) 8" x 63" (203 x 1600) NOTES: 1. Filter sizes for the CH models are recommended filter sizes only. No filter is factory provided with these models. 30 2. Sizes shown are nominal ordering sizes. International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com Horizontal Series PIPING PACKAGES (TYPICAL) Two-way Motorized Control Valve Three-way Motorized Control Valve In a two-way motorized control valve package, the motor In a three-way motorized control valve package, a diverting drives the valve open, and a spring returns the valve to a valve controls water flow to the coil. When the unit is off, normally closed position. No water flows with the unit off. water bypasses the coil and flows directly to the system The standard supply connection from the coil will accept return. A balancing valve may be specified in the bypass line a swaged copper fitting for field brazing. As an option, this to permit equal flow balancing. connection may be factory furnished with a union. When a Air Vent swage is necessary, it becomes part of the valve package. The isolation, or ball, valve in the return piping is shipped Ball Valve R Swage loose for field installation. Coil Air Vent 3-way Valve Ball Valve R Optional Balance Valve S R Swage (Ships Separate) A Aquastat Coil 2-way Valve R Ball Valve S NOTES: 1. Please note that project specifications for system Ball Valve S Swage S Two-way Motorized Control Valve with Changeover In a two-way motorized changeover control valve package, the motor drives the valve open, and a spring returns the valve to a normally closed position. No water flows through the coil with the unit off. The aquastat bypass line allows pressure, pressure drop limitations and flow rate should be checked prior to selecting specific components or the valve package size. 2. The supply and return piping connections of the factory-provided valve package are either swaged for field brazing (standard) or union fitted (optional) for connection to the coil. 3. Consult IEC’s Valve Packages and Piping Components manual or your local representative for detailed piping and valve application information. Factoryprovided valve packages are assembled, brazed, wired electrically and dry-fit to the coil connections before shipping. Field brazing to the coil completes the installation. Some applications dictate shipping isolation valves loose. a small amount of water to flow from the supply to the return piping when the control valve is closed. The strapon aquastat senses whether the flowing water is cold or hot and switches a contact closed to provide automatic summer/winter changeover (ACO) for the system. Air Vent R Ball Valve Swage Coil Aquastat Bleed Bypass Line 2-way Valve A S Swage R Aquastat Ball Valve S International Environmental Corporation • Horizontal Series Fan Coil Technical Catalog www.iec-okc.com 31 IEC Catalog Part #: I100-90002102 CA-020 Revision 8 (8/2016) ©2000-2016 International Environmental Corporation (IEC) P.O. Box 2598 Oklahoma City, OK 73101-2598 p: 405.605.5000 f: 405.605.5001 www.iec-okc.com