The Strada is Exposure’s specific road light with high and
dipped beam modes. The Strada is supplied with a Remote
Switch that can take the place of the Function Button so you
can change modes without moving your hand to the light.
LiGHt oPeRation
Located on the back of the light unit is the Function Button and
two sets of LEDs. When the light is on, the red LEDs indicate
battery life. Blue LEDs indicate mode selected. 3 LEDs high, 2
medium and 1 low.
· To turn on the light, double click the Function Button;
the light turns on in the brightest mode.
· To switch between the constant settings, press the
button once.
oPtiMiseD MoDe seLectoR (oMs)
· When light is off press and
hold the Function Button.
After 3 seconds multiple
flashes indicate SPT+ is
activated, keep holding the
Function Button OMS will now
begin and the LED’s on the
back cap will light in sequence.
Re-cHaRGinG instRUctions
1. Ensure the light unit is turned off.
· To turn off the light, press and hold the Function Button.
The light will briefly go out, then flash twice. Release the
button and the light will have switched off.
3. Open the storm cap on the charge port then insert the
charger connection plug into the light’s charge port. The
charger’s LED will show red when the light unit is charging.
The number of red LEDs lit indicates the approx percentage of
battery power left.
When all LEDs are out, the light output will drop to the low
setting. This will result in the light to diming overtime.
A 35mm QR bracket is available at www.use1.com.
1
2
· The number of lit LED’s
denotes the program
selected.Release button
when required program is reached.
· To activate the flashing or SOS mode, press and hold the
button, release immediately after one flash. The flashing
mode can be activated from any of the constant modes.
To return to the high mode, press the button once.
FUeL GaUGe FUnction
Mounting to a 25.4 or 26mm bar - Place the plastic spacers
around your bar, attach the bracket over the spacers and
tighten the clamp with a 4mm hex key. (Maximum 5 Nm)
2. Plug the Smart Charger into the power supply and switch
on the supply. The LED on the charger will show green
(operational).
The red LEDs on the rear of light indicate approx charge state
up to 80%. From empty the light unit will rapid charge till approx
95% at this point the LED on the charger will go from red to
green, and trickle charge to 100%. This could take up to an
additional 1hr to reach max charge.
QUicK ReLease BRacKet
The Exposure QR bracket is a triumph in design that brings to
life the full benefit of Exposure’s principle feature, Cable Free
Design (CFD). The light unit is simply and securely attached
and removed. The bracket stays with the bike and the light will
be in the perfect position every time it is attached.
Mounting to a 31.8mm bar – Remove the plastic spacer from the
bracket. Wrap the supplied Silicone band, (marked Exposure 31.8)
around the handlebar and clamp bracket over the band to protect
the bars. Tighten the clamp with a 4mm hex key. (Maximum 5Nm)
sMaRt PoRt tecHnoLoGY PLUs (sPt+)
The Smart Port Technology Plus not only enables the user to charge
the light but also to power accessories and ancillary products.
To Activate Smart Port Technology Plus without the front light
being on, press and hold the function button, immediately
release when the main light rapid flashes. Accessories and
ancillary products will now be powered. Some ancillary
products such as mobile devices will require the Exposure
Boost Cable to boost to 5 volts.
To switch the Smart Port OFF - simply turn the light on and off.
Ensure that the Smart Port is switched off before charging.
Attach the cleat to the light
unit using the provided bolt
(Already fitted to new lights).
3
To adjust the horizontal angle
of the light, loosen the cleat
bolt. A hole in the bracket
enables access to the bolt
when the light is in the
bracket. Use a 4mm hex key
to adjust and tighten the bolt
securely (Maximum 5Nm).
Locate the cleat into the V
section of the bracket and
slide forward until the steel
pin “clicks” into place.
The Smart Port Technology Plus automatically becomes active
when the main light is switched on. It also automatically shuts
down when the light is turned off.
inteLLiGent tHeRMaL ManaGeMent (itM)
4
Exposure Lights patented technology combats loss in efficiency of
To release the light from the
bracket pull down on the red
button and gently pull back
the light with your hand.
Exposure Lights have undertaken extensive research into the effect
of temperature on LED output. There is an optimum temperature
where the balance between light output and battery burntime
peaks, Beyond this LEDs becomes inefficient. The intelligent
circuitry of ITM monitors the temperature of the LEDs and adjusts
power accordingly to ensure the LEDs remain at the optimum
efficiency. The adjustment of the power doesn’t noticeably drop the
light output, it only maximises burntime. The combination of ITM
and new improved body designs for increased heat dissipation
ensures that no power is wasted, maximising burn time.
Do not oVeR tiGHten!
WARNING - Make sure that brake and gear cables cannot
catch on or interfere with the light, bracket or release button.
Racers beware - check number boards do not interfere with
bracket button. If the steel pin cannot pop-up fully the light will
not be fully engaged to the bracket and may come off.
LEDs at elevated temperatures. The technology maintains optimum
output for maximum efficiency.
QUICKSTART GUIDE READY, SET UP, RIDE
Maintenance
Accessories
Inspect and test your light before every ride.
·· QR Bracket
·· USB Boost Cable
Keep your Exposure light clean, and the lenses free of dirt.
The lenses are made of hi-tech resistant resin but can be
scratched. Be careful when cleaning any mud or dirt from
the lens. Never use a high pressure spray or hose on your
Exposure light. Do not use harsh abrasive or corrosive
materials to clean your Exposure light.
·· Red Eye
·· Car Charger
·· Remote Switch
·· Beacon - 3
·· Support cell 3.1 and 8.7
Follow all charging instructions. If the unit is being stored
for long periods, please ensure the battery is periodically
charged fully. We suggest once every month. The same
applies to support cell batteries.
WARNING
Exposure Lights are very powerful lighting systems. Always
take care when operating. Do not look directly into the light.
This may cause serious injury. Do not shine directly at others.
Exposure Lights / Ultimate Sports Engineering Ltd. accept no
liability for any injuries or other damages arising from the use
of their product in any circumstances.
We design them. We make them. We are here to help.
If you are experiencing any problems with your Exposure
Light or accessories please contact us directly at:
Service: +44 (0)1798 839300
service@exposurelights.com
Alternatively contact your Exposure Dealer/Distributor check
web for details www.exposurelights.com
EXPOSURE LIGHTS
STRADA MK5