DC/DC Converters Selection Guide
Rev. 7.0
www.rohm.com
Table of Contents
Secondary Side
Primary Side
ROHM Website
2
AC
Product Pickup
Buck Converter (Integrated Switch FET)
AC/DC
Transformer
3
Buck Controller (External Switch FET)
15
Isolated DC/DC Power Supply
19
DC
Switching Regulator
DC/DC
PFC
Wireless
power supply
Isolated
DC/DC
converter
Voltage
Detector
Linear Regulator
LDO
High-side Switch
Lineup
Power Supply Block Schematic Chart
Single Output Buck Converter (Integrated Switch FET)
21
Dual Output Buck Converter (Integrated Switch FET)
25
Buck Controller (External Switch FET)
25
Boost/Buck-boost/SEPIC and Inverting
26
Product List and Selection Guide
Buck Converter (Integrated Switch FET)
27
Boost/Buck-boost/SEPIC and Inverting Converters
33
Isolated DC/DC Power Supply
33
Controller (External Switch FET)
34
DC/DC Converters Selection Guide
www.rohm.com
ROHM's product lineup covers the entire area
of power supplies. This selection guide features
DC/DC switching regulators and isolated
DC/DC converters.
Pages 3 to 20 introduce select products with
specific characteristics.
Page 3 shows characteristics of the buck
converter BD9x families.
Pages 5 to 13 introduce buck converters with
specific characteristics by input voltage range.
Page 14 shows the buck type switching
regulators that operate at a maximum 6 MHz.
The chip-sized package and coil of low inductor
value allow for a miniature power supply
configuration that is especially suited for
portable equipment.
Pages 15 to 18 show controller ICs that allow
for power supply configurations for high
current output by attaching a MOSFET to the
IC external. Page 15 presents an application
example that delivers both high-speed load
response and high current output in the power
supply for FPGA. Page 16 explains ROHM’s
proprietary H3RegTM high-speed transient
response technology that is used for the
controller ICs.
Page 17 introduces controllers with a 60V
rating and high current applications using ICs.
Page 19 features isolated DC/DC switching
regulators that assuredly improve reliability as
they do not require an optocoupler.
Pages 21 to 26 show lineup tables, and
Page 27 and following pages show product
lists. You can select ICs based on representative
values and functions.
Before using a ROHM IC, be sure to check its
setting values, data and functions against the
latest data sheet.
1
ROHM Website
For ROHM’s power supply IC lineup, visit
the following ROHM website.
http://www.rohm.com
ROHM provides design and technical data
and tools such as data sheets, application
notes, technical notes, reference designs and
evaluation boards to assist developers.
DC/DC Converters
http://micro.rohm.com/en/techweb/
http://deviceplus.com/
Before using a ROHM IC, be sure to check its setting values, data and functions against the latest data sheet.
2
DC/DC Converters Selection Guide
www.rohm.com
Pickup
Buck Converter (Integrated Switch FET)
BD9x Family System Diagram
24V
Input
power
rail
voltage
12V
5.0V
3.3V
Current mode control
BD9B100
BD9B200
BD9B300
BD9B400
BD9B500
BD9B600
1A
2A
3A
4A
5A
6A
*1
*1
*1
*1
*1
*1
BD9C301
BD9C401
BD9C501
BD9C601
On-time control
3A
4A
5A
6A
Current mode control
BD9Exxx
Series
BD9Dxxx
Series
BD9D320 3A
BD9D321 3A *1
On-time control
Pin compatible
*1
*1
*1
*1
BD9Cxxx
Series
Pin compatible
1A
3A
4A
6A
BD9Bxxx
Series
Pin compatible
BD9A100
BD9A300
BD9A400
BD9A600
*2
Pin compatible
Pin compatible
Pin compatible
BD9Axxx
Series
BD9E100
BD9E101
BD9E102
BD9E300
BD9E301
BD9E302
BD9E303
1.0A
1.0A
1.0A
2.5A
2.5A
3.0A
3.0A
1MHz
570kHz
570kHz *1
1MHz
570kHz
570kHz *1
300kHz
Current mode control
*1: Automatic switching from PWM to PFM at light load
*2: CRs with a single pin must be replaced by a jumper resistor.
The above diagram shows the buck
The BD9Bxxx Series, in the other green
The BD9Cxxx Series in the blue group
light-load high efficiency modes. ICs in
converter BD9x Family systems. These
group, adopts on-time control and
supports an input power rail voltage of
this series are pin-compatible, which
lists are color-coded and ICs of the same
supports output currents of 1A, 2A, 3A,
12V. As a secondary power supply, it is
enables easy replacement according to
color are pin-compatible. The BD9Axxx
4A, 5A and 6A. This series offers faster
available with a 5V input. This series
efficiency requirements under light load.
Series in the green group supports input
load response characteristics and higher
adopts current mode control and supports
The BD9Exxx Series in the red group
power rail voltages of 3.3V and 5.0V.
efficiency at light load than the BD9Axxx
output current of 3A, 4A, 5A and 6A. ICs
supports input power rail voltages of 12V
This series adopts current mode control,
Series. ICs of the BD9Bxxx Series are
in this series are pin-compatible.
and 24V. This series adopts current mode
supports output currents of 1A, 3A, 4A
also pin-compatible. Moreover, ICs are
The BD9Dxxx Series in the orange group
control and supports output currents of 1A,
and 6A, and features high-speed load
pin-compatible between the BD9Axxx
supports an input power rail voltage of
2.5A and 3A and switching frequencies of
response characteristics. Since ICs of this
Series and BD9Bxxx Series, which
12V. As a secondary power supply, it is
300 kHz, 570 kHz and 1MHz. ICs of 1A
series are pin-compatible, replacement is
enables easy replacement in the event of
available with a 5V input. For the output
and 3A include models that ensure high
easy even when the current design value
urgent design changes, such as in a case
current, only a 3A type is available, but it
efficiency under light load.
changes.
where a faster load response is required.
includes two IC models with/without the
DC/DC Converters Selection Guide
www.rohm.com
3
BD9x Family Lineup
○ - Current Mode Control
◎ - On-time Control
▼ - Light Load Mode
△ - Nonsynchronous
◎ BD9F800MUX
8.0
6.0
Maximum Rating
ROHM’s single output buck DC/DC converters
provide a power supply solution that satisfies your
specification requirements based on a matrix of input
voltage and output current. In the product name of
BD9x Family, the numeric value “9” following “BD”
represents the “buck” topology, the subsequent
alphabet represents the maximum rated input voltage
and the subsequent numeric value represents the
output current.
30V
○ BD9C601EFJ
20V
○ BD9C501EFJ
20V
○ BD9C401EFJ
20V
◎ BD9B600MUV ▼
○ BD9A600MUV ▼
5.0
◎ BD9B500MUV ▼
◎ BD9B400MUV ▼
4.0
Part No. Description
Output Current (A)
○ BD9A400MUV ▼
3.0
◎ BD9D321EFJ ▼
20V
◎ BD9D320EFJ
20V
○ BD9C301FJ / BD9C301FJ-LB
20V
SW=570kHz
◎ BD9B300MUV / BD9B301MUV-LB ▼
B
○ BD9G341AEFJ △
9
Topology
9 : Buck
8 : Boost, Buck-Boost,
Inverting
○ BD9E301EFJ-LB
40V
○ BD9E300EFJ-LB
40V
○ BD9E151NUX △
30V
○ BD9E102FJ ▼
30V
○ BD9E101FJ-LB
40V
Maximum Rated Input
Voltage and Control Mode
A : ≤ 7V Current Mode
B : ≤ 7V On-time
C : ≤ 20V Current Mode
D : ≤ 20V On-time
E : ≤ 40V Current Mode
F : ≤ 40V On-time
G : ≤ 80V Current Mode
○ BD9E100FJ-LB
40V
Note: There are some part numbers that do not conform with this rule
○ BD9G101G △
45V
SW=570kHz
◎ BD9B100MUV ▼
SW=1MHz
○ BD9A100MUV / BD9A101MUV-LB ▼
0.5
3.3
5.0
Serial No.
00, 01, 02, ･･･
40V
SW=570kHz
1.0
0
○ BD9E303EFJ-LB
◎ BD9B200MUV ▼
1.2
0
30V
SW=1MHz
2.0
3
○ BD9E302EFJ ▼
SW=570kHz
2.5
A
80V
SW=300kHz
○ BD9A300MUV / BD9A301MUV-LB ▼
D
12
24
Output Current
1 : ≤ 1A
2 : ≤ 2A
3 : ≤ 3A
4 : ≤ 4A
・
・
A：≤ 10A
・
Z : Controller
48
Input Power Rail Voltage (V)
4
DC/DC Converters Selection Guide
www.rohm.com
Pickup
Buck Converter (Integrated Switch FET)
3.3V/5V Power Rail Input
BD9B300MUV light-load automatic switching mode
Power Supply Solution for Consumer Equipment
BD9A300MUV light-load automatic switching mode
The BD9A100MUV, BD9A300MUV, BD9A600MUV and BD9B300MUV generate a low voltage of about 1.8 V from power
supplies of 5V or 3.3V.
5V or 3.3V
PC/Tablet board
BD9A300MUV
or
BD9A600MUV
3.3V, 3A
3.3V, 6A
100
90
NAND Flash Memory
80
Enable
BD9A100MUV
EFFICIENCY (%)
Example: Storage
70
1.8V, 1A
DDR Memory
2.5V, 1A
BD9A100MUV
1.2V, 3A
BD9B300MUV
Controller
- DDR controller
- NAND Flash controller
- I/F
- I/O
60
50
40
Conditions
VIN = 5.0V
VOUT = 1.8V
fSW = 1MHz
30
20
10
0
0.001
Product example: BD9B300MUV
 Input voltage range
： 2.7V to 5.5V
 Output voltage range ： 0.8V to (VIN×0.8)V
 Reference-voltage
： 0.8V±1.0%
 Output current
： 3A
 Switching frequency ： 1MHz / 2MHz
 Integrated switch FET ： 35mΩ
 Current consumption ： 35μA
 High speed transient response characteristics with
constant-on-time control
 Light-load high-efficiency mode
 Selectable between light-load automatic switching
mode and PWM constant mode
 Adjustable soft start
 Power good output
 Various protection functions
Over current protection (OCP), short-circuit protection
(SCP), thermal shutdown (TSD), undervoltage lockout
(UVLO)
BD9A300MUV
PWM constant
mode
0.01
0.1
LOAD CURRENT (A)
1
10
Efficiency vs. Load Current
VIN
Enable
10µF
BD9B300MUV
BD9B300MUV
PVIN
PGD
PVIN
PGD
AVIN
AVIN
BOOT
BOOT
EN
EN
15mm×8mm
PGD
CBOOT
0.1µF
VOUT
AGND
AGND
SW
SW
1.0µH
PGND
PGND
R1
SS
CFB
22µF×2
MODE
MODE
CSS
FREQ
FREQ
FB
FB
R2
BD9B300MUV Application Circuit
BD9B300MUV PCB
DC/DC Converters Selection Guide
www.rohm.com
5
Selectable from Two Series Depending on the System
The BD9AxxxMUV Series and BD9BxxxMUV Series consist of pin-compatible ICs of 1A to 6A. Thus, you can select the best IC for your application. These series operate in the PWM mode
for an application with high load current, and automatically switch to power-saving operation with SLLMTM (PFM mode) for an application with low load current. The BD9BxxxMUV is a
high-performance version of the BD9AxxxMUV series. Both versions can be interchangeably replaced by changing the PCB layout of a single pin. Also, by drawing a PCB layout compatible
with both series in the initial stage of development, ICs can be easily changed.
Product name
Light-load
operation
Control mode
High performance
Upper
Compatible
BD9B100MUV
BD9B200MUV
BD9B300MUV
BD9B301MUV-LB
BD9B400MUV
BD9B500MUV
BD9B600MUV
Constant-on-time
Deep SLLM
BD9A100MUV
BD9A101MUV-LB
BD9A300MUV
BD9A301MUV-LB
BD9A400MUV
BD9A600MUV
Current mode
SLLMTM
Functional difference
• Constant-on-time control helps implement transient response faster than that of the BD9AxxxMUV.
• Phase compensation is unnecessary.
• Efficiency across the entire load range is further improved over the BD9AxxxMUV.
• The product operates in the light-load automatic switching mode by setting the MODE pin to Low and in
the PWM constant mode by setting it to High.
• The product operates at 2 MHz by setting the FREQ pin to Low and at 1 MHz by setting it to High.
A small 1 μH coil can be used at 2 MHz.
• The product operates in the PWM constant mode by setting the MODE pin to Low and in the light-load
automatic switching mode by setting it to High.
(This Load
is the Mode
same function as the BD9Bxxx Series, but the logic is reversed.)
SLLM : Simple Light
PVIN
C1
C8
GND
SS 9
AGND
FB
ITH
MODE
5
6
7
8
11
BD9B300MUV
BD9BxxxMUV
10
3
VOUT
GND
PGND
SS 9
4
C5
4
L1
SW
2
VIN
GND
PGND
12
C2
VOUT
C7
10
3
13
BOOT
PVIN
11
BD9A300MUV
BD9AxxxMUV
C2
C1
GND
SW
14
PGD
1
L1
2
VIN
15
EN
C8
12
1
16
AVIN
C7
13
BOOT
C6
14
PGD
AGND
FB
5
6
FREQ MODE
7
C5
15
EN
C6
16
AVIN
PGOOD
ENABLE
PGOOD
ENABLE
SLLMTM : Simple Light Load Mode (Automatic switching from PWM to PFM in the light-load mode)
8
R1
R1
www.rohm.com
J1
J2
Difference in External Components
DC/DC Converters Selection Guide
J3
R2
J1
R3
C3
R2
C4
6
Pickup
Buck Converter (Integrated Switch FET)
3.3V/5V Power Rail Input
Thin Type, High-Speed Transient Response Power Supply Solution
The BD91364BMUU provides the highest class of transient response in the industry by incorporating constant-on-time control and an overshoot reduction function. The adopted low type
package is best suited for mounting on slim equipment.
Existing products
BD91364BMUU
VIN: 5V, VO: 1.2V
VIN: 5V, VO: 1.2V
8.5mV
VOUT: 50mV/div
88.5mV
IO: 1A/div
IO = 1A → 3A → 1A
IO = 1A → 3A → 1A
100μsec/div
100μsec/div
BD91364BMUU High-Speed Transient Response Characteristics
Product example: BD91364BMUV
 Input voltage range
： 2.9V to 5.5V
 Output voltage range ： 0.8V to (VIN×0.8)V
 Reference-voltage
： 0.8V±1.5%
 Output current
： 5A
 Switching frequency
： 1.7MHz
 Integrated switch FET ： 27mΩ
High speed transient response characteristics with constant-on-time control
The light-load automatic switching mode enables high efficiency across the
entire load range.
The overshoot reduction function reduces the increase in output voltage in
the event of rapid changes in load current.
Adjustable soft start
 Power good output
 Various protection functions
Over current protection (OCP), short-circuit protection (SCP), thermal
shutdown (TSD), undervoltage lockout (UVLO)
Conditions
VIN = 5.0V
BD91364BMUU - Efficiency vs. Load Current
BD91364BMUU Thin Type Package
VQFN20U4040M
4.0mm×4.0mm×0.5mm
typ
typ
max
7
DC/DC Converters Selection Guide
www.rohm.com
C6
VIN
22μH
R3
PVCC
PVCC
3A output
BST
BST
Enable
Power Good
EN
EN
U1
BD91364BMUU
C3
Reduced
by 29%
0.47μH
VOUT
SW
SW
R1
PGD
PGD
FB
FB
SS
SS
RES
AGND
RES AGND
Soft Start
5A output
AVCC
AVCC
PGND
PGND
C4
22μH
BD91364BMUU PCB
17mm×10mm
Existing PCB
15mm×16mm
R2
Comparison of PCB Mounting Area
BD91364BMUU Application Circuit
Overshoot Reduction
When the load current rapidly reduces, the output voltage increases. Thus, the low-side MOSFET remains ON. At this time, the inclination of the coil current ∆IL becomes -Vo/L. If the slew
rate ∆Iout of the load current Iout becomes greater than ∆IL, continuous charging of excess current to the output capacitor increases the output voltage (shown as a dotted waveform). Especially,
when the output voltage setting value is low, the value of ∆IL becomes small and a more marked increase in output voltage occurs.
The BD91364BMUU activates the overshoot reduction function when the low-side MOSFET remains ON twice as long as PWM operates. By turning OFF both the low-side and high-side
MOSFETs and flowing IL through the low-side MOSFET body diode, -Vf voltage is generated in the SW pin. Accordingly, ∆IL becomes (-Vf-Vo)/L, which suppresses charging of excess
current to the output capacitor and reduces the increase in output voltage.
Inclination ΔIL=
45mV
150mV
Dotted lines show operation of the
existing product.
VOUT : 100mV/div
VOUT : 100mV/div
SW : 5V/div
SW : 5V/div
IOUT : 2A/div
4.5A→0A
Twice as long as normal LG High time
Switching Circuit
Output Voltage Transient
Characteristics of Existing
Product
IOUT : 2A/div
4.5A→0A
Output Voltage Increase Reduction
Effect of Overshoot Reduction
8
DC/DC Converters Selection Guide
www.rohm.com
Pickup
Buck Converter (Integrated Switch FET)
12V Power Rail Input
Power Supply Solution for Consumer Equipment
The BD9D320EFJ, BD9D321EFJ, BD9C301FJ, BD9C401EFJ, BD9C501EFJ and BD9C601EFJ generate voltages of 5V
100
and 3.3V from a 12V power supply.
Isolated
AC/DC
12V
Example: AV equipment
BD9D320EFJ
BD9D321EFJ
5V, 3A
BD9D320EFJ
BD9D321EFJ
5V, 3A
BD9D320EFJ
BD9D321EFJ
1.8V, 3A
BD9D320EFJ
BD9D321EFJ
3.3V, 3A
80
Tuner, AV broad
70
EFFICIENCY (%)
AC 85 ～ 265 V
VOUT =5.0V
VOUT = 3.3V
VOUT = 1.8V
90
USB ports
DDR Memory
60
50
40
30
BD9C301FJ
BD9C401EFJ
BD9C501EFJ
BD9C601EFJ
Conditions
VIN = 12V
20
Controller
- DDR controller
- I/F
- I/O
3.3V
3A, 4A,
5A, 6A
10
0
0.001
Product example: BD9D321FEJ
0.01
1
10
BD9D321EFJ - Efficiency vs. Load Current
 Input voltage range
： 4.5V to 18V
 Output voltage range ： 0.765V to 7.0V, (VIN×0.07)V to (VIN×0.65)V
 Reference-voltage
： 0.765V±1.5%
 Output current
： 3A
VIN
 Switching frequency ： 700 kHz
 Integrated switch FET ： 100mΩ, 70mΩ
10µF×2
 High speed transient response characteristics with
+
0.1µF
constant-on-time control
 Phase compensation parts are unnecessary.
 A ceramic capacitor is available for output.
 Synchronous rectification type
 Light-load high efficiency mode
 Adjustable soft start that prevents rush current at power ON
Various protection functions
CVREG
Over current protection (OCP), short-circuit protection (SCP),
thermal shutdown (TSD), undervoltage lockout (UVLO)
BD9D321EFJ
BD9D321EFJ
VIN
VIN
Enable
CBOOT
EN
EN
SW
SW
GND
GND
VREG
VREG
SS
SS
CSS
2.2µH
VOUT
R1
22µF
×2
FB
FB
ILOAD
2A/div
IO = 1A→3A→1A
100μs/div
R2
BD9D321EFJ Transient Response
Characteristics
17mm×20mm
BD9D321EFJ PCB
www.rohm.com
VIN = 12V
VOUT = 1.8V
VOUT
50mV/div
BOOT
BOOT
BD9D321EFJ Application Circuit
DC/DC Converters Selection Guide
0.1
LOAD CURRENT (A)
9
Pickup
Buck Converter (Integrated Switch FET)
24V Power Rail Input
Power Supply Solution for Home Appliances
The BD9E102FJ and BD9E302EFJ generate voltages of 5V and 3.3V from power supplies of 24V and 15V.
Replacement of the LDO enables energy-savings and reduced heat generation.
100
BD9E102FJ
90
Example: Refrigerator
・ Motor driver
・IPM (Intelligent Power Module)
80
EFFICIENCY (%)
70
AC 85 ～ 265 V
Replaces LDO
5.0V, 1A
15V
BD9E102FJ
Isolated
AC/DC
Sensor and monitor
- Thermistor (Refrigerator)
- Thermistor (Freezer)
- CO2 sensor
60
50
LDO
(BA50BC0WT)
40
30
Replaces LDO
15V
BD9E302EFJ
5.0V, 3A
Conditions
VIN = 12V
VOUT = 5.0V
20
Controller
- Digital signal controller
- Network
- Touch screen
- Compressor
10
0
1
Product example: BD9E102FJ
10
100
LOAD CURRENT (mA)
1000
BD9E102FJ - Efficiency vs. Load Current
 Input voltage range
 Output voltage range
： 7.0V to 26V (30V rating)
： (VIN×0.143)V to (VIN×0.7)V
(VIN×0.143)1.0V
VIN
12V
 Reference-voltage
： 0.8V±2.0%
 Output current
： 1.0A
10μF
 Switching frequency ： 570 kHz
 Supports an input rating of 28V that is greatly demanded for electric home
appliances.
Enable
 The excellent efficiency under light load is ideal for equipment that needs to
suppress standby power consumption.
 Integrated switch FET ： 250mΩ, 200mΩ
 High-speed transient response characteristics are delivered by controlling the
current mode. Phase compensation can be set easily.
 Because of synchronous rectification, an external diode is unnecessary.
 Soft start to prevent rush current at power ON
Various protection functions
Over current protection (OCP), short-circuit protection (SCP),
thermal shutdown (TSD), undervoltage lockout (UVLO)
VIN
VIN
BD9E102FJ
BD9E102FJ
BOOT
BOOT
0.1μF
SW
SW
EN
EN
6.8μH
VOUT
5.0V
22μF
AGND PGND
COMP
FB
COMP AGND
PGND FB
430kΩ
82k
BD9E102FJ Application Circuit
BD9E102FJ Evaluation Board
10
DC/DC Converters Selection Guide
www.rohm.com
Pickup
Buck Converter (Integrated Switch FET)
24V Power Rail Input
Power Supply Solution for Industrial Equipment
from power supplies of 24V and 12V.
AC 85 ～ 265 V
Isolated
AC/DC
BD9E303EFJ-LB
100
The BD9E100FJ, BD9E101FJ, BD9E300EFJ, BD9E301EFJ and BD9E303EFJ generate voltages of 5V and 3.3V
90
24V
5V, 1A
BD9E100FJ-LB
80
Base Unit
- ASIC
70
BD9E101FJ-LB
5V, 2.5A
BD9E300EFJ-LB
1.8V, 3A
BD9E303EFJ-LB
EFFICIENCY (%)
BD9E300EFJ-LB
3.3V, 1A
I/O Unit
- ASIC
60
50
40
Conditions
VIN = 24V
VOUT=5.0V
30
Analog Unit
- ASIC
20
10
CPU Unit
- CPU
0
0
0.5
1
1.5
2
2.5
3
LOAD CURRENT (A)
Product example: BD9E303EFJ-LB
Efficiency vs. Load Current
Long-term supply indispensable for industrial equipment is assured.
VIN
24V
Supports an input rating of 40V that is greatly demanded for
industrial equipment.
10μF
 Input voltage range
： 7.0V to 36V (40V rating)
 Output voltage range ： (VIN×0.06)V to (VIN×0.8)V
(VIN×0.06)1.0V
Enable
 Reference-voltage
： 1.0V±1.0%
 Output current
： 3.0A
 Built in low ON-resistance switch FET: 90mΩ, 80mΩ
 High-speed transient response characteristics are delivered by
controlling the current mode.
 Because of synchronous rectification, an external diode is unnecessary.
 Soft start to prevent rush current at power ON
Various protection functions
Over current protection (OCP), short-circuit protection (SCP),
thermal shutdown (TSD), undervoltage lockout (UVLO)
VIN
VIN
BD9E303EFJ-LB
BD9E303EFJ-LB
BOOT
BOOT
0.1μF
SW
EN
EN
COMP
COMP
10μH
VOUT
5.0V
22μF×2
AGND
AGND PGND
PGND
FB
FB
30k
6800pF
15k
7.5k
Efficient heat radiation characteristics
owing to exposed pad
BD9E303EFJ-LB Application Circuit
11
DC/DC Converters Selection Guide
www.rohm.com
Selectable According to System
The BD9E300EFJ-LB and BD9E303EFJ-LB are both buck DC/DC converters with a power rail input of 24V, but they have been developed based on different concepts. Since the
BD9E300EFJ-LB is a high-speed type with a switching frequency of 1 MHz, a small inductor can be used to assure space-savings of the PCB mounting area. Since the BD9E303EFJLB has a integrated FET of low ON-resistance and a low switching frequency of 300 kHz, it assuredly reduces switching-loss and minimizes heat generation with high efficiency.
Product name
Feature
BD9E300EFJ-LB
Small space-saving
size
BD9E303EFJ-LB
Low heat
generation
Switching
frequency
1MHz
300kHz
Inductor
value
FET ONresistance
Efficiency
Output
current
Maximum Minimum
duty ratio duty ratio
4.7μH
170mΩ
140mΩ
See the
upper-right
figure on
previous page.
2.5A
70%
15%
27mm×10mm
270mm2
10μH
90mΩ
80mΩ
See the
upper-right
figure on
previous page.
3A
80%
6%
33mm×15mm
495mm2
PCB size
24V Small Size Power Supply Solution
Product example: BD9G101G
VIN
24V
BD9G101G
VCC
VCC
100
BST
BST
4.7μF
LX
LX
Enable
6.8μH
GND
GND
FB
FB
3.9k
680
www.rohm.com
70
VIN=24V
VOUT=5.0V
60
50
40
30
0.1μF
BD9G101G Application Circuit
20
10
0
1
SSOP6
2.9mm×2.8mm
h: 1.25mm
DC/DC Converters Selection Guide
80
VOUT
5.0V
10μF
EN
EN
VIN=12V
VOUT=5.0V
90
0.015μF
EFFICIENCY (%)
DC/DC converter with integrated MOSFET with 45 V rating
 Input voltage range
： 6.0V to 42V (45V rating)
 Output voltage range ： (VIN×0.15)V to (VIN×0.7)V
(VIN×0.15)1.0V
 Reference-voltage
： 0.75V±1.5%
 Output current
： 500mA
 High-speed switching frequency of 1.5 MHz enables use of
small size inductor.
 Diode rectification automatically activates the pulse skip
mode under light load to maintain the high efficiency.
 Integrated High-side switch FET: 800mΩ
 High-speed transient response characteristics are delivered
by controlling the current mode.
 Built-in phase compensation circuit
 Soft start to prevent rush current at power ON
Various protection functions
Over current protection (OCP), thermal shutdown (TSD),
undervoltage lockout (UVLO)
10
100
LOAD CURRENT (mA)
1000
BD9G101G - Efficiency vs. Load Current
12
Pickup
Buck Converter (Integrated Switch FET)
Supporting Maximum 76 V Input
Product example:BD9G341AEFJ
The BD9G341AEFJ is a 1-ch buck switching regulator with a integrated switch FET of 80 V rating (76 V input). Since sufficient voltage margin is ensured in a 48 V bus line adopted
by communication infrastructures, this switching regulator easily enables safe power supply design in high voltage applications such as telephones, routers and base stations.
BD9G341AEFJ
LX pin voltage
20V/div
 Input voltage range ： 12V to 76V (80V rating)
 Output voltage range ： 1.0V to VIN*1
*1 Limitations apply under some
conditions.
 Reference-voltage
： 1.0V±1.5%
 Output current
： 3.0A
 Integrated switch MOSFET of 80 V rating: 150mΩ
 High-speed transient response characteristics are delivered by
controlling the current mode. Phase compensation can be set
easily.
 Soft start to prevent rush current at power ON
 Operating frequency can be set from 50 kHz to 750 kHz.
 Precise EN threshold: ±3%
Various protection functions
Over current protection (OCP), overvoltage protection (OVP),
thermal shutdown (TSD), undervoltage lockout (UVLO)
Output current
2A/div
IC Surface Temperature in Output Short-Circuit
5ms/div
In the event of an output short-circuit, the over current
protection circuit is used in the hiccup mode to prevent IC
heating and destruction.
100
BD9G341AEFJ
90
BD9G341AEFJ
BD9G341EFJ
VIN
VIN
BST
BST
10μF
70
0.1μF
LX
LX
EN
EN
33μH
VOUT
5.0V
100μF
RT
RT
GND
GND
VC
VC
Conditions
VIN = 48V
VOUT = 5.0V
fSW=300kHz
80
FB
FB
EFFICIENCY (%)
VIN
Competitor product
+1.5%
+16.3%
60
+21.3%
50
Competitor
product
40
30
3k
20
10
750
0
1
BD9G341AEFJ Application Circuit
Efficient heat radiation characteristics
owing to exposed pads
10
100
LOAD CURRENT (mA)
1000
BD9G341AEFJ - Efficiency vs. Load Current
DC/DC Converters Selection Guide
www.rohm.com
3000
13
Pickup
Buck Converter (Integrated Switch FET)
6 kHz High-Frequency Operating Switching Regulator
 Input voltage range ： 2.3V to 5.5V
Output voltage:
: 1.0V, 1.2V, 1.25V, 1.3V, 1.8V, 1.83V, 2.5V, 3.0V, 3.3V
Output voltage precision: ±2.0%
Output current:
: 1.0A
Switching operation of maximum 6 MHz
Ultra-small 1.3 mm × 0.9 mm size chip package
High-speed transient response characteristics with hysteresis control eliminate phase
compensation.
The PWM/PFM automatic switching function delivers high efficiency across the
entire load area.
The forced PWM mode keeps the switching frequency constant.
 Soft start to prevent rush current at power ON
Various protection functions
7mm×4mm
Over current protection (OCP), thermal shutdown (TSD), undervoltage lockout
(UVLO)
BU90002GWZ PCB
EFFICIENCY (%)
BU90xxxGWZ Series
L : LQM21MPN1R0NG0 (Murata)
LOAD CURRENT (mA)
BU90xxxGWZ - Efficiency vs. Load Current
VOUT
50mV/div
Output
voltage
Product name
Input voltage
range
Switching
frequency
Maximum
output
capacitor
PWM/PFM
automatic
switching
Forced PFM
Forced PWM
Package
1.0V
BU90008GWZ
2.3V～5.5V
3.6MHz
10μF
✔
－
✔
UCSP35L1
1.2V
BU90003GWZ
2.3V～5.5V
4MHz
10μF
✔
－
✔
UCSP35L1
1.25V
BU90007GWZ
2.3V～5.5V
4MHz
10μF
✔
－
✔
UCSP35L1
1.3V
BU90009GWZ
2.3V～5.5V
4.2MHz
10μF
✔
－
✔
UCSP35L1
1.8V
BU90004GWZ
BU90054GWZ
BU90104GWZ
2.3V～5.5V
5.4MHz
10μF
10μF
100μF
✔
－
✔
UCSP35L1
UCSP30L1
UCSP35L1
1.83V
BU90090GWZ
2.3V～5.5V
5.4MHz
10μF
✔
－
✔
UCSP35L1
✔
UCSP35L1
2.5V
BU90005GWZ
2.3V～5.5V
6MHz
10μF
－
✔
(100mA max)
3.0V
BU90006GWZ
2.3V～5.5V
6MHz
10μF
✔
－
✔
UCSP35L1
3.3V
BU90002GWZ
4.0V～5.5V
6MHz
10μF
✔
－
✔
UCSP35L1
UCSP30L1 : 1.3mm×0.9mm×0.33mm
UCSP35L1 : 1.3mm×0.9mm×0.4mm
DC/DC Converters Selection Guide
www.rohm.com
IOUT
200mA/div
10μs/div
BU90003GWZ Transient Response Characteristics
(50mA  350mA)
BU90xxxGWZ
VIN
VIN
VIN
LW
LX
1.0μH
VOUT
4.7μF
4.7μF
FB
FB
Enable
EN
EN MODE
MODE GND
GND
BU90xxxGWZ Application Circuit
14
Pickup
Buck Controller (External Switch FET)
Power Supply Solution for FPGA
The BD95601MUV-LB and BD95602MUV-LB are power supply ICs outfitted with H3RegTM technology that ensures high-speed transient response characteristics required by FPGA. These
models generate power supply voltage from a 12 V input voltage, thus satisfying the stringent voltage precision specifications required by FPGA.
FPGA Power Board Tree
12V
BD95601MUV-LB
1.0V±3.00%, 6A
BD95601MUV-LB
1.8V±5.00%, 6A
BD95601MUV-LB
2.0V±3.00%, 2A
2.5V±5.00%, 8A
BD95602MUV-LB
3.3V±5.00%, 8A
BD95601MUV-LB
1.0V±3.00%, 6A
BD95601MUV-LB
1.5V/1.35V±5.00%, 4A
BD95601MUV-LB
1.2V±2.50%, 4A
BD95602MUV-LB Circuit Diagram
VIN: 12V, VO: 3.3V
BD95602MUV-LB
 2ch DC/DC controller equipped with H3RegTM for high-speed
transient response
 Selectable from light-load mode, continuous PWM mode and silent
and light-load mode
 The adjustable soft start function reduces rush current at startup.
 Power good output
 Integrated with various protection
 Input voltage range ： 5.5V to 28V
functions
 Output voltage range ： 1.0V to 5.5V
・ Automatic reset type over current
 Reference-voltage： 0.7V±1.0%
protection (OCP)
 Switching frequency ： 150kHz to 500kHz ・ Overvoltage protection function
DC/DC Converters Selection Guide
(OVP)
・ Thermal shutdown function (TSD)
・ Undervoltage lockout function
(UVLO)
www.rohm.com
VOUT: 100mV/div
IO: 5A/div
IL: 5A/div
20μsec/div
BD95602MUV-LB High-Speed Transient Response
Characteristics
Avnet Inc.
Power module board (Kintex-7) for MiniModule Plus development system
15
High-speed Transient Response Technology
H3RegTM Control Ensures High-Speed Response to Load Fluctuation
Generally, the current mode is used as the switching regulator control mode. However, transient response characteristics for fluctuating load current may not satisfy the required specifications.
To solve this problem, it is effective to use a switching regulator in the hysteresis control mode. Constant-on-time control, one of the hysteresis control modes, feeds back a ripple voltage
waveform generated by the output voltage and controls switching by comparing the bottom of the ripple voltage against the reference voltage so as to keep the output voltage constant. When
the feedback voltage becomes lower than the reference voltage, a one-shot pulse is generated to turn ON the high-side switch, which enables current supply from input to output. In this way,
H3RegTM enables successive switching control via a straightforward comparison by a comparator. Since this method substantially eliminates time delays in feedback control, faster transient
response characteristics than those in the current mode can be obtained.
H3RegTM control is a ROHM proprietary control mode and an advanced version of constant-on-time control. If the load current increases rapidly and, accordingly, the output voltage drops to
the point that the feedback voltage does not exceed the reference-voltage even after the specified on-time has passed, H3RegTM control extends the on-time of the high-side switch and supplies
more power to accelerate output voltage recovery. This control mode assures faster transient response characteristics than constant-on-time control does. In addition, less frequent switching
caused by rapid load fluctuations reduces noise generation.
H3Reg
Controller
SW
R
IL
Q
Driver
IL
IO
VOUT
Io
S
SW
Vref
Constant-On-Time Control Operation Waveform
H3RegTM Block Diagram
IL
Io
SW
t+α
H3RegTM Control Operation Waveform
16
DC/DC Converters Selection Guide
www.rohm.com
Pickup
Buck Controller (External Switch FET)
Buck Controller Supporting Maximum 56 V Input
Product example: BD9611MUV
The BD9611MUV is a rated 60 V synchronous rectification type buck DC/DC controller that enables high voltage input and a wide input voltage range. This model incorporates the control
circuit in the PWM and has voltage modes and drive circuit for two external 10V N-ch FETs. The oscillating frequency and soft start time adjustment function, over current protection function
and synchronization function with external clock featured in this model enable flexible design. In addition, a low input malfunction prevention circuit (EXUVLO) of precise reference voltage is
connected to the CTL pin, and can be adjusted from the VCC-GND resistance ratio. Pre-bias is supported to suppress current incoming from the output side at startup.












Input voltage range
： 10V to 56V (60V rating)
Output voltage range
： 1.0V to (VIN×0.8)V
Reference-voltage
： 0.8V±1.0%
Integrated drive circuit for external N-ch FET
Gate drive voltage
： 9.0V to 11V
Pre-bias supported
Adjustable soft start that prevents rush current at power ON
Operating frequency can be set from 50 kHz to 500 kHz.
UVLO value can be set with an external component.
Synchronization with external clocks is available.
Multi-channel output synchronization using multiple ICs is available.
Various protection functions
Over current protection (OCP), thermal shutdown (TSD), undervoltage lockout (UVLO)
FB
CTL
VCC
CLH
CLL
RCL
INV
SS
BST
BD9611MUV
HG
REG5
LX
RTSS
RT
REG10
LG
SYNC
CLKOUT
GND PGND
100%
Efficiency
95%
BD9611MUV Application Circuit
VIN=24V
VIN=36V
90%
85%
VIN=48V
80%
Conditions
VOUT = 12V
fSW = 250kHz
75%
70%
0
2
4
6
8
10
12
Load Current[A]
BD9611MUV - Efficiency vs. Load Current
VIN = 34V, VOUT = 12V, IO= 0A → 10A
BD9611MUV Transient Response
Characteristics
Efficient heat radiation characteristics owing to
exposed pad
17
DC/DC Converters Selection Guide
www.rohm.com
200 W Power Supply Solution
 Input voltage
： 40V
 Output voltage
： 24V
 Output current
： 0.01A to 8A
 Switching frequency ： 100kHz
100
90
EFFICIENCY (%)
80
VIN
CVCC
R7
1
CSS 2
3
16
18
19
17
CLH
CLL
BST
BST
15
HG
14
LX
BD9611MUV
RB161VA-20
FB
FB
RT
40
Conditions
VIN = 40V
VO = 24V
fSW = 100kHz
30
20
RSD221N06×3
13
0
TR2
DI1 CBST
12
0
L1
4.7μ H
3
4
5
6
7
8
COUT2
BD9611MUV - Efficiency vs. Load Current
CSNB
CREG10
11
2
LOAD CURRENT (mA)
VOUT
COUT1
1
RSD221N06
TR1
SYNC
RTSS
7
6
RT
LG
50
10
CLO PGND SYNC
10
RCL
RCL
PGND
REG10
9
4
60
RHG
RSNB
5
RCL
INV
CLKOUT
C2
R2
BD9611MUV
8
C1
CIN
CLL
SS
SS
RTSS
RD1
R1
VCC CLH
RS
GND
RT
RU1
CTL
VCC
REG5
REG5
R5
CTL
20
CREG5
70
High-side FET : 56.1℃
CRTSS
Inductor : 56.2℃
BD9611MUV 200W Output Application Circuit
IC : 57.4℃
Low-side FET : 58.9℃
Ta = 25℃
PCB Temperature Distribution
18
DC/DC Converters Selection Guide
www.rohm.com
Pickup
Isolated DC/DC Power Supply
Flyback Converter
Product example ：BD7F100HFN-LB, BD7F100EFJ-LB
The BD7F100HFN-LB and BD7F100EFJ-JB are ICs for newly developed isolated flyback DC/DC converters. Since control of the primary side flyback voltage stabilizes the secondary
side output, an output feedback path is unnecessary. This eliminates the optocoupler that is required by general isolated converters to isolate the feedback path. Accordingly, owning to the
cost reduction and elimination of components required to ensure a long service-life, unit reliability can be improved. In terms of performance, high-speed load response is implemented
using adaptive on-time control and the automatic light-load mode realizes high efficiency across the entire load range. In addition, cross-regulation is dramatically improved. These models
are suitable for isolated power supplies for various industries, such as power supplies for isolated gate drivers of inverters.
 Input voltage range ： 3.0V to 40V (45V rating)
 Switch pin voltage
： 50V (60V rating)
 Switch current limit ：1.25A
 Operating frequency ： 400kHz
 Reference-voltage
： ±1.5%
 High-speed load response is implemented by adaptive on-time control.
 Frequency-constant operation facilitates EMC solutions.
 The automatic light-load mode realizes high efficiency across the entire load range.
 Elimination of components across the isolation boundary improves functional safety.
 Elimination of components of finite service-life enables long operation.
 Multi-output configurations of excellent cross-regulation are supported.
 Load compensation function integrated in the secondary SBD
 Output voltage can be set from two external resistors and the transformer winding ratio.
 Integrated soft start function
 Various protection functions
Over current protection (OCP), thermal shutdown (TSD), undervoltage lockout (UVLO)
Example: Inverter
VIN
VOUT_UH
BD7F100HFN-LB
GND_UH
VIN
VIN
VOUT_UH
Isolator
MCU
Gate Driver
GND_UH
VIN
VIN
24V
VIN
VIN
10µF
63µH
SDX/EN
SDX/EN
BD7F100HFN-LB
BD7F100HFN-LB
GND_WH
VOUT_WH
7µH
VIN
REF
REF
VOUT_WH
Gate Driver
GND_WH
WH
GND_WH
VOUT_L
47µF
SBD
VOUT-
BD7F100HFN-LB
GND_L
FB
FB
COMP
COMP
AGND
AGND
VOUT+
5V, 1A
SBD
GND_UH
BD7F100HFN-LB
Isolator
BD7F100HFN-LB
HSON8
2.90mm×3.00mm×0.60mm
UH
VOUT_WH
VIN
3:1
VOUT_UH
SW
SW
PGND
PGND
3.9kΩ
BD7F100HFN-LB Application Circuit
24V→5V
www.rohm.com
DC/DC Converters Selection Guide
VIN
BD7F100EFJ-LB
HTSOP-J8
4.90mm×6.00mm×1.00mm
VOUT_L
VOUT_L
Isolator
Gate Driver
UL
Isolator
Gate Driver
WL
GND_L
GND_L
19
1:1:1
VIN
24V
VIN
VIN
10µF
50µH
SDX/EN
SDX/EN
BD7F100HFN-LB
BD7F100HFN-LB
REF
REF
50µH 10µF
Example: RS485 Transceiver
Vcc1
SBD
50µH
SBD
SW
SW
PGND
PGND
BD7F100HFN-LB
10µF
VOUT-15V, -220mA
Vcc1
3.9kΩ
BD7F100HFN-LB Application Circuit
24V→±15V
10µH
SDX/EN
SDX/EN
BD7F100HFN-LB
BD7F100HFN-LB
DI
Isolator
RS485 transceiver
RO
22µF
VOUT-
SBD
5.25
FB
FB
SW
SW
PGND
PGND
5.2
8
5.15
3.9kΩ
BD7F100HFN-LB Application Circuit
5V→5V
MAXIMUM OUTPUT POWER (W)
REF
REF
7
OUTPUT VOLTAGE (V)
COMP
COMP
AGND
AGND
40µH
Vcc2
Vcc1
DE
VOUT+
5V, 240mA
SBD
VIN
VIN
10µF
MCU
1:2
VIN
5V
Vcc2
COM
FB
FB
COMP
COMP
AGND
AGND
VOUT+
15V,220mA
SBD
6
5
4
3
2
5.05
5
Without load
compensation
4.95
4.9
Conditions
VIN = 24V
VOUT = 5.0V
4.85
4.8
1
4.75
0
0
0
5
10 15 20 25 30 35 40 45 50
VIN VOLTAGE (V)
BD9F100HFN-LB Maximum Output Power vs. Input
Power Supply Voltage
BD7F100HFN-LB Evaluation Board
With load
compensation
5.1
200
400
600
800
1000
LOAD CURRENT (mA)
Effect of Load Compensation Function
“Load compensation function” that corrects output
voltage drops caused by the Vf characteristics of
the secondary side SBD that is dependent on load
current
20
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Single Output Buck Converters (Integrated Switch FET)
Unless otherwise specified: - Current mode control - Soft start - Synchronous rectification - Enable
○ - On-time control
◎ - H3RegTM control
- PWM mode
- Light-load efficiency
5V
3.3V
12V
○
8.0
- Maximum rating
30V PGD
BD95500MUV
20V
Package
0.3 / 0.6
PGD , Adj.SS
0.2 to 1.0
0.765 to (VIN×0.7)
(VIN×0.7) ≤ 13.5V
VQFN11X3535M
0.7 to 5.0
VQFN040V6060
0.35 to 0.8
BD9A600MUV
PGD , Adj.SS
1.0
0.8 to (VIN×0.7)
VQFN016V3030
2.9V BD9B600MUV
PGD , Adj.SS
1.0 / 2.0
0.8 to (VIN×0.8)
VQFN016V3030
0.5
(VIN×0.075) to (VIN×0.7)
(VIN×0.075) ≥ 0.8V
HTSOP-J8
1.7
0.8 to (VIN×0.8)
VQFN20U4040M
1.0 / 2.0
0.8 to (VIN×0.8)
T.B.D. (QFN)
0.2 to 1.0
0.7 to 5.0
VQFN032V5050
0.5
(VIN×0.125) to (VIN×0.7)
(VIN×0.125) ≥ 0.8V
HTSOP-J8
BD9C601EFJ
Output current (A)
VOUT (V)
(VIN×0.075) to (VIN×0.7)
(VIN×0.075) ≥ 0.8V
0.8 to (VIN×0.5)
(VIN×0.5) ≤ 5.5V
6.0
◎
20V
○ 2.9V BD91364BMUU
○
BD95861MUV
20V
PGD, Adj.SS , Remote sense
BD9B500MUV
PGD , Adj.SS
◎
BD95514MUV
30V
BD9C401EFJ
▲
0.5
20V PGD
BD9C501EFJ
5.0
SW Freq.
(MHz)
24V
BD9F800MUX
◎
○
PGD – Power good
Adj.SS – Adjustable soft start
▲ - Non-synchronous
rectification
20V
BD9327EFJ / -LB
4.75V
4.0
PGD, Adj.SS
20V
Adj.SS
◎ BD95841MUV PGD
○
BD9B400MUV
PGD , Adj.SS
HTSOP-J8
VQFN024V4040
0.38
0.9 to (VIN×0.9)
HTSOP-J8
0.5 to 0.8
0.8 to (VIN×0.5)
(VIN×0.5) ≤ 5.5V
VQFN016V3030
1.0 / 2.0
0.8 to (VIN×0.8)
VQFN016V3030
VQFN016V3030
BD9A400MUV
PGD, Adj.SS
1.0
0.8 to (VIN×0.7)
BD91361MUV
2bit VID
1.0
0.8 to 3.3 *1
VQFN020V4040
1.0
*1
VQFN020V4040
BD9137MUV
2.3 2.5 2.7 3.0 3.5
4.0
4.5
5.5
6.0
7.0 7.5
14
15
18
28
32
42
56
76
0.8 to 3.3
Input voltage (V)
*1 Limitations apply according to input/output voltage
21
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Single Output Buck Converters (Integrated Switch FET) (Continued from the previous page)
Unless otherwise specified: - Current mode control - Soft start - Synchronous rectification - Enable
○ - On-time control
◎ - H3RegTM control
- PWM mode
- Light-load efficiency
- Maximum rating
5V
3.3V
PGD – Power good
Adj.SS – Adjustable soft start
▲ - Non-synchronous
rectification
12V
BD9G341AEFJ / -LB
BD9E303EFJ-LB
36V
BD9E302EFJ
BD9D320EFJ
○
BD9D321EFJ
◎ BD95831MUV
Output current (A)
◎
0.55
20V
Adj.SS
0.7
20V
Adj.SS
0.7
0.5 to 0.8
30V
BD9326EFJ / -LB
▲
3.0
40V
0.3
PGOOD
BD9C301FJ / -LB
4.75V
80V 0.05 to 0.75
30V
BD95513MUV
▲
VOUT (V)
Package
24V
▲
○
SW Freq.
(MHz)
PGD, ASS
1.0 to (VIN×0.7)
HTSOP-J8
(VIN×0.06) to (VIN×0.8)
(VIN×0.06) ≥ 1.0V
(VIN×0.143) to (VIN×0.7)
(VIN×0.143) ≥ 1.0V
0.765 to 7.0
(VIN×0.07) to (VIN×0.65)
0.765 to 7.0
(VIN×0.07) to (VIN×0.65)
0.8 to (VIN×0.5)
(VIN×0.5) ≤ 5.5V
VQFN016V3030
HTSOP-J8
HTSOP-J8
HTSOP-J8
HTSOP-J8
0.2 to 1.0
0.7 to 5.0
VQFN032V5050
20V
0.5
(VIN×0.125) to (VIN×0.7)
(VIN×0.125) ≥ 0.8V
SOP-J8
20V Adj.SS
0.38
0.9 to (VIN×0.9)
HTSOP-J8
0.75
1.0 to (VIN×0.7)
HTSOP-J8
1.0
3.3
VQFN020V4040
BD9859EFJ
BD9134MUV
○
BD9B301MUV-LB
PGD, Adj.SS
1.0 / 2.0
0.8 to (VIN×0.8)
VQFN016V3030
○
BD9B300MUV
PGD, Adj.SS
1.0 / 2.0
0.8 to (VIN×0.8)
VQFN016V3030
BD9A301MUV-LB
PGD, Adj.SS
1.0
0.8 to (VIN×0.7)
VQFN016V3030
BD9A300MUV
PGD, Adj.SS
1.0
0.8 to (VIN×0.7)
VQFN016V3030
BD9139MUV
1.0
0.8 to 3.3
BD8963EFJ
1.0
1.0 to 2.5 *1
BD8962MUV
1.0
0.8 to 2.5
*1
VQFN020V4040
BD9132MUV
1.0
0.8 to 3.3 *1
VQFN020V4040
2.5
2.3 2.5 2.7 3.0 3.5
4.0
4.5
5.5
6.0
7.0 7.5
*1
VQFN016V3030
HTSOP-J8
BD9E301EFJ-LB
36V
40V
0.57
(VIN×0.0855) to (VIN×0.7)
(VIN×0.0855) ≥ 1.0V
HTSOP-J8
BD9E300EFJ-LB
36V
40V
1.0
(VIN×0.15) to (VIN×0.7)
(VIN×0.15) ≥ 1.0V
HTSOP-J8
14
15
18
28
32
42
56
76
Input voltage (V)
*1 Limitations apply according to input/output voltage
22
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Single Output Buck Converters (Integrated Switch FET)
(Continued)
Unless otherwise specified: - Current mode control - Soft start - Synchronous rectification - Enable
○ - On-time control
◎ - H3RegTM control
- PWM mode
- Light-load efficiency
3.3V
- Maximum rating
5V
▲
PGD – Power good
Adj.SS – Adjustable soft start
▲ - Non-synchronous
rectification
12V
0.9 to (VIN×0.9)
SOP-J8
0.5
VQFN020V4040
0.5 to 0.8
2.5 to 6.0
(Vccmin=VOUT+1.3V)
0.8 to (VIN×0.5)
(VIN×0.5) ≤ 5.5V
BD8961NV
1.0
3.3
SON008V5060
BD9111NV
1.0
3.3
SON008V5060
13.2V
BD9110NV
Output current (A)
VQFN016V3030
1.0
1.0 to 2.5
SON008V5060
1.0 / 2.0
0.8 to (VIN×0.8)
VQFN016V3030
1.0
1.0 to 2.5 *1
HTSOP-J8
BD8960NV
1.0
1.0 to 2.5
*1
SON008V5060
BD9130EFJ/NV
1.0
1.0 to 2.5 *1
HTSOP-J8
SON008V5060
1.23
VSON008X2030
BD9B200MUV
PGD
BD89630EFJ
1.5
Package
0.38
20V
◎ BD95821MUV PGD
○
VOUT (V)
24V
BD9325FJ / -LB
4.75V
BD9141MUV
2.0
SW Freq.
(MHz)
○
BU90023NUX
1.0
○
BU90028NUX
1.0
1.175
VSON008X2030
0.6
(VIN×0.06) to (VIN×0.7)
(VIN×0.06) ≥ 1.0V
VSON008X2030
1.0
1.0 to 1.8
MSOP8
▲
30V Adj.SS
BD9E151NUX
BD8964FVM
1.2
BD9107FVM
BD9123MUV
3bitVID
BD9E100FJ-LB
BD9E101FJ-LB
BD9E102FJ
▲
1.0
BD9227F
BD8313HFN
BD9B100MUV
26V
20V
1.0
1.0 to 1.8
MSON8
1.0
0.85 to 1.2
VQFN016V3030
36V
40V
1.0
36V
40V
0.57
30V
0.57
1.0
100%Duty
100%Duty
PGD
(VIN×0.15) to (VIN×0.7)
(VIN×0.15) ≥ 1.0V
(VIN×0.0855) to (VIN×0.7)
(VIN×0.0855) ≥ 1.0V
(VIN×0.143) to (VIN×0.7)
(VIN×0.143) ≥ 1.0V
(VIN×0.252) to VIN
(VIN×0.252) ≥ 1.0V
SOP-J8
SOP-J8
SOP-J8
SOP8
1.0
1.2 to 12
HSON8
1.0 / 2.0
0.8 to (VIN×0.8)
VQFN016V3030
BD9A101MUV-LB
PGD, Adj.SS
1.0
0.8 to (VIN×0.7)
VQFN016V3030
BD9A100MUV
PGD, Adj.SS
1.0
0.8 to (VIN×0.7)
VQFN016V3030
2.3 2.5 2.7 3.0 3.5
4.0
4.5
5.5
6.0
7.0 7.5
14
15
18
28
32
42
56
76
Input voltage (V)
*1 Limitations apply according to input/output voltage
23
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Single Output Buck Converters (Integrated Switch FET)
(Continued)
Unless otherwise specified: - Current mode control - Soft start - Synchronous rectification - Enable
- PWM mode
- Light-load efficiency
○ - On-time control
◎ - H3RegTM control
3.3V
Output current(A)
1.0
5V
- Maximum rating
PGD – Power good
Adj.SS – Adjustable soft start
▲ - Non-synchronous
rectification
12V
VOUT (V)
Package
24V
○
BU90008GWZ
3.6
1.0
UCSP35L1
○
BU90003GWZ
4.0
1.2
UCSP35L1
○
BU90007GWZ
4.0
1.25
UCSP35L1
○
BU90009GWZ
○
BU90004GWZ / BU90054GWZ
○
BU90104GWZ
○
BU90090GWZ
○
BU90005GWZ
○
BU90006GWZ
4.2
1.3
UCSP35L1
Maximum output capacity 10μF
5.4
1.8
UCSP35L1/UCSP30L1
Maximum output capacity 100μF
5.4
1.8
UCSP35L1
5.4
1.83
UCSP35L1
100%Duty
6.0
2.5
UCSP35L1
100%Duty
6.0
3.0
UCSP35L1
6.0
3.3
UCSP35L1
BD8967FVM
1.0
3.3
MSOP8
BD9104FVM
1.0
3.3
MSOP8
1.5
1.2 to 12
HSON8
○ BU90002GWZ
BD8312HFN
100%Duty
BD9109FVM / -LB
1.0
3.3
MSOP8
BD9102FVM
1.0
1.24
MSOP8
BD8966FVM
1.0
1.0 to 2.5
MSON8
BD9106FVM / -LB
1.0
1.0 to 2.5
MSON8
1.0
1.2
MSOP8
1.0
1.0 to 1.5
HSON8
1.0
1.0 to 3.3
MSON8
1.5
(VIN×0.15) to (VIN×0.7)
(VIN×0.15) ≥ 1.0V
SSOP6
1.0
1.0 to 2.0
VCSP50L2
0.8
BD9103FVM
BD9120HFN
0.6
SW Freq.
(MHz)
BD9161FVM / -LB
100%Duty
▲
0.5
0.3
BD9G101G
45V
BD9122GUL
2.3 2.5 2.7 3.0 3.5
4.0
4.5
5.5
6.0
7.0 7.5
14
15
18
28
32
42
56
76
Input voltage (V)
24
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Dual Output Buck Converters (Integrated Switch FET)
Unless otherwise specified: - Current mode control - Soft start - Synchronous rectification - Enable
◎ - H3RegTM control
- PWM mode
- Light-load efficiency
PGD – Power good
- Maximum rating
3.3V
SW Freq.
(MHz)
5V
12V
HTSOP-J8
0.4 to 0.8
Ch1: 0.8 to 5.5
Ch2: 0.8 to 5.5
VQFN032V5050
Ch1: 1.5A
Ch2: 1.5A
1.5
Ch1: 3.3
Ch2: 0.8 to 2.5
VQFN020V4040
Ch1: 1.5A
Ch2: 1.5A
1.0
Ch1: 3.3
Ch2: 0.8 to 2.5
VQFN020V4040
1.0
Ch1: 1.8
Ch2: 1.2
VQFN020V4040
1.65
Ch1: 2.55
Ch2: 1.8
VQFN016V3030
Output current (A)
8V
BD93291EFJ
26V
Ch1: 3.0A
◎ BD95830MUV Ch2: 3.0A
1.5
BD9152MUV
0.8
0.4
3.0A
30V Ch1:
Ch2: 2.0A
Ch1: 5.0
Ch2: 0.8 to 4.0
3.0
4.75V
2.8V
BD9151MUV
2.3 2.5 2.7 3.0 3.5
4.0
Ch1: 0.4A
Ch2: 0.8A
PGD, Voltage detector, High-side controller
BD91501MUV
2.55V
100% duty
4.5
5.5
Package
0.3 to 0.6
◎
BD9150MUV
VOUT (V)
24V
6.0
Ch1: 0.4A
Ch2: 0.3A
7.0 7.5
14
15
18
28
32
42
56
Input voltage (V)
76
Lineup of Buck Controllers (External Switch FET)
Unless otherwise specified: - Current mode control - Soft start - Synchronous rectification - Enable
◎ - H3RegTM control
- PWM mode
- Light-load efficiency
3.3V
Controller (External Switch)
- Maximum rating
5V
12V
■(0.05-0.5MHz)
Dual
PGD – Power good
Adj.SS – Adjustable soft start
▲ - Non-synchronous rectification ■ - External synchronization
SW Freq.
(MHz)
VOUT (V)
Package
24V
BD9611MUV
10V
60V Adj.SS 0.05 to 0.5
1.0 to (VIN×0.8)
VQFN020V4040
SSOP-B20
▲
3.6V
BD9848FV
35V
36V
Adj.SS
0.1 to 1.5
Ch1: 1.0 to VIN *1
Ch2: 1.0 to VIN *1
▲
3.6V
BD9845FV
35V
36V
Adj.SS
0.1 to 1.5
1.0 to VIN *1
SSOP-B14
0.01 to 0.3
1.25 to VIN *1
SOP-J8
1.25 to VIN *1
MSOP8
▲
BD63536FJ
▲
BD9305AFVM
4.2V
4.0
No Enable
20V
0.1 to 0.8
Dual ◎
BD9528AMUV
30V
PGD, Adj.SS
0.2 to 0.5
Dual ◎
BD95602MUV-LB
30V
PGD, Adj.SS
0.15 to 0.5
Ch1: 1.0 to 5.5
Ch2: 1.0. to 5.5
Ch1: 1.0 to 5.5
Ch2: 1.0. to 5.5
0.2 to 0.5
0.75 to 2.0
◎
2.3 2.5 2.7 3.0 3.5
32V
30V
BD95601MUV-LB
4.5
5.5
6.0
7.0 7.5
14
28V
25V
15
18
28
32
PGD, Adj.SS
42
56
76
VQFN032V5050
VQFN032V5050
VQFN020V4040
Input voltage (V)
*1 Limitations apply according to input/output voltage
25
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Boost/Buck-boost/SEPIC and Inverting Converters and Controllers
Switch allowable current (mA)
1400
BA9741F / BA9741FS
BA9744FV
Dual ▲ 3.6V
BA9743AFV
Dual ▲
▲
✔
-
-
✔ Voltage
10 to 800
2.5 to *1
SOP16
SSOP-A16
35V
36V Adj.SS
✔
-
-
✔ Voltage
10 to 800
1.222 to *1
SSOP-B16
35V
36V Adj.SS
10 to 800
2.505 to *1
SSOP-B16
▲
BD8158FVM
✔
-
-
✔ Voltage
✔ Voltage
10 to 3000
1.0 to *1
HTSSOP-B20
100 to 800
VIN to (VIN/0.3)
MSOP8
-
BD9306AFVM
20V Soft Start
✔
-
-
-
Voltage
-
✔
-
-
Voltage 200 to 1000
1.8 to 12
VQFN016V3030
Soft Start
✔
-
-
-
Voltage
1200
4.0 to 12
VSON010V3030
Soft Start
✔
-
-
-
Voltage
1200
4.0 to 11
VSON010V3030
Soft Start
✔
✔
-
-
Voltage 300 to 2000
1.8 to 5.2
VQFN016V3030
Adj.SS
✔
✔
✔
-
Current
600/1200
VIN to 14
MSOP8
✔
✔
✔
-
Current
600/1200
VIN to 14
MSOP8
15V Soft Start
Adj.SS
Dual ▲
BD8316GWL
Soft Start
✔
-
-
✔ Current
1600
Ch1: -9.0 to -1.0
Ch2: Vin to +18
UCSP50L1
Dual ▲
BD8317GWL
Soft Start
✔
-
-
✔ Current
800
Ch1: -9.0 to -1.0
Ch2: Vin to +18
UCSP50L1
BU33DV7NUX
Soft Start , Input pass through
✔
-
-
-
Current
600
3.3
VSON010V3030
BU34DV7NUX
Soft Start , Input pass through
✔
-
-
-
Current
600
3.4
VSON010V3030
✔
-
-
-
Current
100
3.3
SSOP5
1000
300
10
Package
-
BD8311NUV
BD8152FVM
VOUT (V)
✔
4.2V
BD8306MUV
SW Freq.
(kHz)
20V Adj.SS
BD8314NUV
▲
Control
mode
BD9851EFV
BD8303MUV
▲
36V Adj.SS
8.8V
Inversing
5.4V
Dual ▲
▲
SEPIC
4.4V
Dual ▲ 3.6V
2000
35V
2cell Li-Ion
2.7V
2500
Buck-boost
Controller (External Switch)
1cell Li-Ion
Boost
▲ - Non-synchronous rectification PGD – Power good
Adj.SS – Adjustable soft start
- Maximum rating
- PWM mode
- Light-load efficiency
BU33DV5G
1.75 1.8 2.1 2.5 2.7
3.0
3.5
4.0
4.5
5.5 6.0
11 12
14
18
28
36
42
Input voltage (V)
*1 Limitations apply according to input/output voltage
26
DC/DC Converters Selection Guide
www.rohm.com
Buck Converters (Integrated Switch FET)
3.3 V/5 V Power Rail Input Selection Guide
Features
Input
Voltage
Range
(V)
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
BD9122GUL
7
0.3
2.5～5.5
1.0～2.0
1
Current
-
-
-
✔
Latch
BD9161FVM
BD9161FVM-LB
7
0.6
2.5～4.5
1.0～3.3
1
Current
-
-
-
✔
✔
Latch
BU9006GUZ
7
0.75
2.5～4.5
1.0～VIN
2
Current
-
-
-
✔
-
BD9109FVM
BD9109FVM-LB
7
0.8
4.5～5.5
3.3
1
Current
-
-
-
✔
✔
Latch
BD9102FVM
7
0.8
4.0～5.5
1.24
1
Current
-
-
-
✔
✔
BD8966FVM
7
0.8
4.0～5.5
1.0～2.5
1
Current
-
-
-
✔
BD9106FVM
BD9106FVM-LB
7
0.8
4.0～5.5
1.0～2.5
1
Current
-
-
-
BD9120HFN
7
0.8
2.7～4.5
1.0～1.5
1
Current
-
-
BD8967FVM
7
0.8
4.5～5.5
3.3
1
Current
-
BD9104FVM
7
0.8
4.5～5.5
3.3
1
Current
New BU90008GWZ
7
1
2.3～5.5
1.0
3.6
BU90003GWZ
7
1
2.3～5.5
1.2
BU90007GWZ
7
1
2.3～5.5
New BU90009GWZ
7
1
BU90004GWZ
7
BU90054GWZ
Operating
Temperature
(℃)
Package
(mm)
✔
Latch
-25～+85
VCSP50L2
(2.5×1.1)
Latch
-25～+85
MSOP8
-35～+85
VCSP35L1
(1.6×1.6)
Latch
-25～+85
MSOP8
Latch
Latch
-25～+85
MSOP8
-
Latch
Latch
-25～+85
MSOP8
✔
✔
Latch
Latch
-25～+85
MSOP8
-
✔
✔
Latch
Latch
-25～+85
HSON8
-
-
✔
-
Latch
Latch
-25～+85
MSOP8
-
-
-
✔
✔
Latch
Latch
-25～+85
MSOP8
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
4
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
1.25
4
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
2.3～5.5
1.3
4.2
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
1
2.3～5.5
1.8
5.4
On-time
-
-
-
✔
✔
Recove Recove Maximum output capacitance
ry
ry 10μF
-40～+85
UCSP35L1
(1.3×0.9×0.4)
7
1
2.3～5.5
1.8
5.4
On-time
-
-
-
✔
✔
Recove Recove Maximum output capacitance
ry
ry 10μF
-40～+85
UCSP30L1
(1.3×0.9×0.33)
New BU90104GWZ
7
1
2.3～5.5
1.8
5.4
On-time
-
-
-
✔
✔
Recove Recove Maximum output capacitance
ry
ry 100μF
-40～+85
UCSP35L1
(1.3×0.9×0.4)
New BU90090GWZ
7
1
2.3～5.5
1.83
5.4
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
Part No.
Power Good
Thermal Protection
Output
Current
(A)
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Input
Voltage
Maximum
Rating
(V)
Description
Recove Recove Incorporates in/output bias switch,
ry
ry 100% Duty
27
DC/DC Converters Selection Guide
www.rohm.com
Buck Converters (Integrated Switch FET)
3.3 V/5 V Power Rail Input Selection Guide (Continued)
Output
Current
(A)
Input
Voltage
Range
(V)
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
BU90005GWZ
7
1
2.3～5.5
2.5
6
On-time
-
-
-
✔
✔
BU90006GWZ
7
1
2.3～5.5
3.0
6
On-time
-
-
-
✔
BU90002GWZ
7
1
4.0～5.5
3.3
6
On-time
-
-
-
BD9A100MUV
BD9A101MUV-LB
7
1
2.7～5.5
0.8～(VIN×0.7)
1
Current
✔
-
BD9B100MUV
7
1
2.7～5.5
0.8～(VIN×0.8)
1/2
On-time
✔
BD8964FVM
7
1.2
4.0～5.5
1.0～1.8
1
Current
BD9107FVM
7
1.2
4.0～5.5
1.0～1.8
1
BD9123MUV
7
1.2
2.7～5.5
0.85～1.2
BU90023NUX
7
1.5
2.3～5.5
BU90028NUX
7
1.5
BD8961NV
7
BD9111NV
Thermal Protection
Features
Input
Voltage
Maximum
Rating
(V)
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
✔
✔
Recove Recove
ry
ry
-40～+85
UCSP35L1
(1.3×0.9×0.4)
✔
✔
✔
Recove Recove
ry
ry
-40～+85
-40～+125
VQFN016V3030
-
✔
✔
Deep
Recove Recove
ry
ry
-40～+85
VQFN016V3030
-
-
-
✔
-
Latch
Latch
-25～+85
MSOP8
Current
-
-
-
✔
✔
Latch
Latch
-25～+85
MSOP8
1
Current
✔
-
-
✔
✔
Latch
Latch
-40～+95
VQFN016V3030
1.23
1
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
VSON008X2030
2.3～5.5
1.175
1
On-time
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+85
VSON008X2030
2
4.5～5.5
3.3
1
Current
-
-
-
✔
-
Latch
Latch
-25～+105
SON008V5060
7
2
4.5～5.5
3.3
1
Current
-
-
-
✔
✔
Latch
Latch
-25～+105
SON008V5060
BD9110NV
7
2
4.5～5.5
1.0～2.5
1
Current
-
-
-
✔
✔
Latch
Latch
-25～+105
SON008V5060
BD89630EFJ
7
2
2.7～5.5
1.0～2.5 *1
1
Current
-
-
-
✔
-
Latch
Latch
-25～+85
HTSOP-J8
BD8960NV
7
2
2.7～5.5
1.0～2.5 *1
1
Current
-
-
-
✔
-
Latch
Latch
-25～+105
SON008V5060
BD9130EFJ
7
2
2.7～5.5
1.0～2.5 *1
1
Current
-
-
-
✔
✔
Latch
Latch
-25～+105
HTSOP-J8
BD9130NV
7
2
2.7～5.5
1.0～2.5 *1
1
Current
-
-
-
✔
✔
Latch
Latch
-25～+105
SON008V5060
7
2
2.7～5.5
0.8～(VIN×0.8)
1/2
On-time
✔
-
✔
✔
Deep
-40～+85
VQFN016V3030
New BD9B200MUV
*1 Restrictions depend on input/output voltage conditions.
DC/DC Converters Selection Guide
www.rohm.com
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Package
(mm)
Power Good
Operating
Temperature
(℃)
Part No.
Recove Recove
ry
ry
Description
Output voltage setting by 3-bit
parallel control
28
Buck Converters (Integrated Switch FET)
3.3 V/5 V Power Rail Input Selection Guide (Continued)
Features
Input
Voltage
Range
(V)
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
BD8962MUV
7
3
2.7～5.5
0.8～2.5 *1
1
Current
-
-
-
-
Latch
BD9132MUV
7
3
2.7～5.5
0.8～3.3 *1
1
Current
-
-
-
✔
✔
BD8963EFJ
7
3
2.7～5.5
1.0～2.5 *1
1
Current
-
-
-
✔
BD9134MUV
7
3
4.5～5.5
3.3
1
Current
-
-
-
BD9139MUV
7
3
2.7～5.5
0.8～3.3 *1
1
Current
-
-
BD9A300MUV
BD9A301MUV-LB
7
3
2.7～5.5
0.8～(VIN×0.7)
1
Current
✔
BD9B300MUV
New BD9B301MUV-LB
7
3
2.7～5.5
0.8～(VIN×0.8)
1/2
On-time
BD9137MUV
7
4
2.7～5.5
0.8～3.3 *1
1
BD91361MUV
7
4
2.7～5.5
0.8～3.3 *1
BD9A400MUV
7
4
2.7～5.5
New BD9B400MUV
7
4
New BD91364BMUU
7
New BD9B500MUV
Operating
Temperature
(℃)
Package
(mm)
✔
Latch
-40～+105
VQFN020V4040
Latch
Latch
-40～+105
VQFN020V4040
-
Latch
Latch
-25～+85
HTSOP-J8
✔
✔
Latch
Latch
-40～+105
VQFN020V4040
-
✔
✔
Latch
Latch
-40～+105
VQFN016V3030
-
✔
✔
✔
Recove Recove
ry
ry
-40～+85
-40～+125
VQFN016V3030
✔
-
✔
✔
Deep
Recove Recove
ry
ry
-40～+85
-40～+125
VQFN016V3030
Current
-
-
-
✔
✔
Recove Recove
ry
ry
-40～+105
VQFN020V4040
1
Current
-
-
-
✔
✔
-40～+105
VQFN020V4040
0.8～(VIN×0.7)
1
Current
✔
-
✔
✔
✔
Recove Recove
ry
ry
-40～+85
VQFN016V3030
2.7～5.5
0.8～(VIN×0.8)
1/2
On-time
✔
-
✔
✔
Deep
Recove Recove
ry
ry
-40～+85
VQFN016V3030
5
2.9～5.5
0.8～(VIN×0.8)
1.7
On-time
✔
-
✔
✔
✔
Recove
ry
-40～+105
VQFN20U4040M
7
5
2.7～5.5
0.8～(VIN×0.8)
1/2
On-time
✔
-
✔
✔
Deep
Recove Recove
ry
ry
-40～+85
VQFN016V3030
BD9A600MUV
7
6
2.7～5.5
0.8～(VIN×0.7)
1
Current
✔
-
✔
✔
✔
Recove Recove
ry
ry
-40～+85
VQFN016V3030
New BD9B600MUV
7
6
2.7～5.5
0.8～(VIN×0.8)
1/2
On-time
✔
-
✔
✔
Deep
Recove Recove
ry
ry
-40～+85
VQFN016V3030
Part No.
Power Good
Thermal Protection
Output
Current
(A)
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Input
Voltage
Maximum
Rating
(V)
Latch
Latch
Latch
Description
Output voltage setting by 2-bit
parallel control
*1 Restrictions depend on input/output voltage conditions.
29
DC/DC Converters Selection Guide
www.rohm.com
Buck Converters (Integrated Switch FET)
12 V Power Rail Input Selection Guide
Features
Input
Voltage
Range
(V)
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
BD8312HFN
15
0.8
3.5～14
1.2～12
1.5
Current
-
-
-
✔
-
-
Recove
ry
-
BD8313HFN
15
1
3.5～14
1.2～12
1
Current
-
-
-
✔
-
-
Recove
ry
22
1
6.0～20
(VIN×0.252)～VIN
(VIN×0.252)≧ 1.0
1
Current
-
-
-
-
-
Recove Recove
ry
ry
BD9141MUV
15
2
4.5～13.2
2.5～6.0 *1
0.5
Current
-
-
-
✔
✔
Latch
Latch
BD95821MUV
15.2
2
7.5～15
0.8～(VIN×0.5)
（VIN×0.5)≦5.5
0.5～0.8
H3 Reg
✔
-
-
✔
-
Latch
Recove
ry
BD9325FJ
BD9325FJ-LB
20
2
4.75～18
0.9～(VIN×0.9)
0.38
Current
-
-
✔
-
-
4.5～18
(VIN×0.125)～(VIN×0.7)
(VIN×0.125)≧ 0.8
0.5
Current
-
-
-
✔
-
7.5～15
0.8～(VIN×0.5)
（VIN×0.5)≦5.5
0.5～0.8
H3 Reg
✔
-
-
✔
-
0.7
On-time
-
-
✔
✔
New BD9227F
BD9C301FJ
BD9C301FJ-LB
BD95831MUV
20
15.2
3
3
Package
100% Duty
-25～+85
HSON8
-
100% Duty
-40～+85
HSON8
-
100% Duty
-40～+85
SOP8
-
-40～+105
VQFN020V4040
✔
-20～+100
VQFN016V3030
Recove Recove
ry
ry
-
-40～+85
SOP-J8
Latch
Recove
ry
-
-40～+85
-40～+125
SOP-J8
Latch
Recove
ry
Over-Voltage
Protection
Operating
Temperature
(℃)
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Part No.
Thermal Protection
Output
Current
(A)
Power Good
Input
Voltage
Maximum
Rating
(V)
Description
✔
-20～+100
VQFN016V3030
-
Recove Recove
ry
ry
-
-40～+85
HTSOP-J8
BD9D320EFJ
20
3
4.5～18
0.765～7.0
(VIN×0.07)～(VIN×0.65)
BD9D321EFJ
20
3
4.5～18
0.765～7.0
(VIN×0.07)～(VIN×0.65)
0.7
On-time
-
-
✔
✔
✔
Recove Recove
ry
ry
-
-40～+85
HTSOP-J8
BD9859EFJ
15
3
5.0～14
1.0～(VIN×0.7)
0.75
Current
-
-
-
-
-
Recove Recove
ry
ry
-
-40～+85
HTSOP-J8
BD9326EFJ
BD9326EFJ-LB
20
3
4.75～18
0.9～(VIN×0.9)
0.38
Current
-
-
✔
-
-
Recove Recove
ry
ry
-
-40～+85
HTSOP-J8
BD9C401EFJ
20
4
4.5～18
(VIN×0.125)～(VIN×0.7)
(VIN×0.125)≧ 0.8
0.5
Current
-
-
-
✔
-
Latch
Recove
ry
-
-40～+85
HTSOP-J8
BD95841MUV
15.2
4
7.5～15
0.8～(VIN×0.5)
（VIN×0.5)≦5.5
0.5～0.8
H3 Reg
✔
-
-
✔
-
Latch
Recove
ry
✔
-20～+100
VQFN016V3030
BD9327EFJ
BD9327EFJ-LB
20
4
4.75～18
0.9～(VIN×0.9)
0.38
Current
-
-
✔
-
-
Recove Recove
ry
ry
-
-40～+85
HTSOP-J8
BD9C501EFJ
20
5
4.5～18
(VIN×0.075)～(VIN×0.7)
(VIN×0.075)≧ 0.8
0.5
Current
-
-
-
✔
-
Latch
Recove
ry
-
-40～+85
HTSOP-J8
BD95861MUV
20
6
7.5～18
0.8～(VIN×0.5)
（VIN×0.5)≦5.5
0.35～0.8
H3 Reg
✔
-
-
✔
-
Latch
Recove
ry
✔
-20～+100
VQFN024V4040
BD9C601EFJ
20
6
4.5～18
(VIN×0.075)～(VIN×0.7)
(VIN×0.075)≧ 0.8
0.5
Current
-
-
-
✔
-
Latch
Recove
ry
-
-40～+85
HTSOP-J8
BD95500MUV
24
6
3.0～20
0.7～5.0
0.2～1.0
H3 Reg
✔
-
✔
✔
✔
Latch
Recove
ry
✔
-10～+100
VQFN040V6060
Output Discharge
*1 Restrictions depend on input/output voltage conditions.
30
DC/DC Converters Selection Guide
www.rohm.com
Buck Converters (Integrated Switch FET)
24 V Power Rail Input Selection Guide
Features
Input
Voltage
Range
(V)
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
BD9G101G
45
0.5
6.0～42
(VIN×0.15)～(VIN×0.7)
(VIN×0.15)≧ 1.0
1.5
Current
-
-
-
-
-
Recove Recove
ry
ry
BD9E100FJ-LB
40
1
7.0～36
(VIN×0.15)～(VIN×0.7)
(VIN×0.15)≧ 1.0
1
Current
-
-
-
✔
-
0.57
Current
-
-
-
✔
Package
-
-40～+105
SSOP6
Recove Recove
ry
ry
✔
-40～+150
SOP-J8
-
Recove Recove
ry
ry
✔
-40～+150
SOP-J8
Over-Voltage
Protection
Operating
Temperature
(℃)
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Part No.
Thermal Protection
Output
Current
(A)
Power Good
Input
Voltage
Maximum
Rating
(V)
Description
BD9E101FJ-LB
40
1
7.0～36
(VIN×0.0855)～(VIN×0.7)
(VIN×0.0855)≧ 1.0
BD9E102FJ
30
1
7.0～26
(VIN×0.143)～(VIN×0.7)
(VIN×0.143)≧ 1.0
0.57
Current
-
-
-
✔
✔
Recove Recove
ry
ry
✔
-40～+85
SOP-J8
BD9E151NUX
30
1.2
6.0～28
(VIN×0.06)～(VIN×0.7) *1
(VIN×0.06)≧ 1.0
0.6
Current
-
-
✔
-
-
Recove Recove
ry
ry
✔
-40～+85
VSON008X2030
BD9701CP-V5
36
1.5
8.0～35
1.0～(VIN-3.0)
0.1
Voltage
-
-
-
-
-
BD9701FP
36
1.5
8.0～35
1.0～(VIN-3.0)
0.1
Voltage
-
-
-
-
-
BD9703CP-V5
36
1.5
8.0～35
1.0～(VIN-3.0)
0.3
Voltage
-
-
-
-
-
BD9703FP
36
1.5
8.0～35
1.0～(VIN-3.0)
0.3
Voltage
-
-
-
-
-
BD9870FPS
36
1.5
8.0～35
1.0～(0.8×(VIN-IO×RON)
0.9
Voltage
-
-
-
-
-
BD9873CP-V5
36
1.5
8.0～35
1.0～(0.8×(VIN-IO×RON)
0.11
Voltage
-
-
-
-
-
BD9778HFP
36
2
7.0～35
(VIN×0.06)～VIN
(VIN×0.06)≧ 1.0
0.05～0.5
Current
-
-
-
-
-
BD9E300EFJ-LB
40
2.5
7.0～36
(VIN×0.15)～(VIN×0.7)
(VIN×0.15)≧ 1.0
1
Current
-
-
-
✔
0.57
Current
-
-
-
BD9E301EFJ-LB
New BD9E302EFJ
BD9E303EFJ-LB
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
Recove
ry
-
100% Duty
-40～+85
TO220CP-V5
-
100% Duty
-40～+85
TO252-5
-
100% Duty
-40～+85
TO220CP-V5
-
100% Duty
-40～+85
TO252-5
-
100% Duty
-40～+85
TO252S-5
-
100% Duty
-40～+85
TO220CP-V5
Recove Recove
ry
ry
-
100% Duty
-40～+125
HRP7
-
Recove Recove
ry
ry
✔
-40～+150
HTSOP-J8
✔
-
Recove Recove
ry
ry
✔
-40～+150
HTSOP-J8
40
2.5
7.0～36
(VIN×0.0855)～(VIN×0.7)
(VIN×0.0855)≧ 1.0
30
3
7.0～28
(VIN×0.143)～(VIN×0.7)
(VIN×0.143)≧ 1.0
0.55
Current
-
-
-
✔
✔
Recove Recove
ry
ry
✔
-40～+85
HTSOP-J8
40
3
7.0～36
(VIN×0.06)～(VIN×0.8)
(VIN×0.06)≧ 1.0
0.3
Current
-
-
-
✔
-
Recove Recove
ry
ry
✔
-40～+150
HTSOP-J8
-
-40～+85
TO220CP-V5
-
-40～+85
TO220CP-V5
BD9702CP-V5
36
3
8.0～35
1.0～(VIN-3.0)
0.11
Voltage
-
-
-
-
-
Recove Recove
ry
ry
BD9874CP-V5
36
3
8.0～35
1.0～(0.8×(VIN-IO×RON)
0.11
Voltage
-
-
-
-
-
Recove Recove
ry
ry
BD95513MUV
30
3
4.5～28
0.7～5.0
0.2～1.0
H3 Reg
✔
-
✔
✔
✔
Latch
Recove
ry
✔
Output Discharge
-10～+100
VQFN032V5050
BD95514MUV
30
4
4.5～28
0.7～5.0
0.2～1.0
H3 Reg
✔
-
✔
✔
✔
Latch
Recove
ry
✔
Output Discharge
-10～+100
VQFN032V5050
4.5～28
0.765～(VIN×0.7)
(VIN×0.7)≦ 13.5
-40～+85
VQFN11X3535M
☆ BD9F800MUX
30
8
☆ Under Development
0.3 / 0.6
On-time
✔
-
-
✔
-
Recove Recove
ry
ry
-
*1 Restrictions depend on input/output voltage conditions.
31
DC/DC Converters Selection Guide
www.rohm.com
Buck Converters (Integrated Switch FET)
Selection Guide for Maximum 75 V Input
BD9G341AEFJ
New BD9G341AEFJ-LB
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
80
3
12～76
1.0～VIN *1
0.05～0.75
Current
-
-
-
-
Over-Voltage
Protection
Input
Voltage
Range
(V)
Thermal Protection
Output
Current
(A)
Power Good
Part No.
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Features
Input
Voltage
Maximum
Rating
(V)
Recove Recove
ry
ry
-
Description
✔
Operating
Temperature
(℃)
Package
-40～+85
HTSOP-J8
*1 Restrictions depend on input/output voltage conditions.
Dual Output Selection Guide
BD91501MUV
2
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
7
Io1 : 0.4
Io2 : 0.3
2.55～5.5
Vo1 : 2.55
Vo2 : 1.80
1.65
Current
2.8～5.5
Vo1 : 1.8
Vo2 : 1.2
1
Current
-
-
-
✔
✔
Latch
-
-
-
✔
✔
Latch
Recove
ry
Over-Voltage
Protection
Input
Voltage
Range
(V)
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Output
Current
(A)
Power Good
Part No.
Thermal Protection
Features
Input
Number
Voltage
of
Maximum
Channels
Rating
(V)
Description
Operating
Temperature
(℃)
Package
-
100% Duty
-30～+105
VQFN016V3030
Latch
-
Voltage Detector,
High-side gate controller
-40～+85
VQFN020V4040
BD9151MUV
2
7
Io1 : 0.4
Io2 : 0.8
BD9150MUV
2
7
Io1 : 1.5
Io2 : 1.5
4.75～5.5
Vo1 : 3.3
Vo2 : 0.8～2.5
1.5
Current
-
-
-
✔
✔
Latch
Latch
-
-40～+85
VQFN020V4040
BD9152MUV
2
7
Io1 : 1.5
Io2 : 1.5
4.5～5.5
Vo1 : 3.3
Vo2 : 0.8～2.5
1
Current
-
-
-
✔
✔
Latch
Latch
-
-40～+85
VQFN020V4040
BD93291EFJ
2
30
Io1 : 2.5
Io2 : 1.5
8.0～26
Vo1 : 5.0
Vo2 : 0.8～4.0
1.5～2.5
H3 Reg
-
-
-
✔
✔
-
-40～+85
HTSOP-J8
15.1
Io1 : 3.0
Io2 : 3.0
7.5～15
Vo1 : 0.8～5.5
Vo2 : 0.8～5.5
-20～+100
VQFN032V5050
BD95830MUV
2
0.4～0.8
H3 Reg
-
-
-
✔
-
Recove Recove
ry
ry
Recove
Latch
Latch
ry
32
DC/DC Converters Selection Guide
www.rohm.com
Lineup of Boost/Buck-boost/SEPIC and Inverting Converters (Integrated Switch FET)
Boost/Buck-boost/SEPIC and Inverting Converter Selection Guide
Switching
Frequency
(kHz)
Control
Mode
Buck-Boost
SEPIC
Inverting
Soft Start
Input
Pass through
UVLO
BU33DV5G
1
10
1.75～4.5
3.3
100
Current
✔
-
-
-
✔
-
-
-
✔
Recove
ry
✔
SSOP5
BU33DV7NUX
1
300
1.8～5.5
3.3
600
Current
✔
-
-
-
✔
✔
✔
✔
✔
Recove
ry
✔
VSON010V3030
BU34DV7NUX
1
300
1.8～5.5
3.4
600
Current
✔
-
-
-
✔
✔
✔
✔
✔
Recove
ry
✔
VSON010V3030
BD8152FVM
1
1400
2.5～5.5
VIN～14
600 / 1200
Current
✔
✔
✔
-
-
-
Adj.
-
✔
Recove
ry
✔
MSOP8
BD8158FVM
1
1400
2.1～4.0
VIN～14
600 / 1200
Current
✔
✔
✔
-
-
-
Adj.
-
✔
Recove
ry
✔
MSOP8
BD8306MUV
1
2000
1.8～5.5
1.8～5.2
300～2000
Voltage
✔
✔
-
-
✔
-
✔
-
✔
Latch
✔
VQFN016V3030
BD8314NUV
1
2500
3.0～12
4.0～12
1200
Voltage
✔
-
-
-
-
-
✔
-
✔
Latch
✔
VSON010V3030
BD8311NUV
1
2500
3.5～11
4.0～11
1200
Voltage
✔
-
-
-
-
-
✔
-
✔
Latch
✔
VSON010V3030
BD8316GWL
2
1000
2.5～5.5
Vo1 : -9.0～-1.0
Vo2 : VIN ～ 18
1600
Current
✔
-
-
✔
-
-
✔
-
✔
Latch
✔
UCSP50L1
(1.8×1.5)
BD8317GWL
2
1000
2.5～5.5
Vo1 : -9.0～-1.0
Vo2 : VIN ～ 18
800
Current
✔
-
-
✔
-
-
✔
-
✔
Latch
✔
UCSP50L1
(1.8×1.5)
Part No.
Thermal
Protection
Output
Voltage
(V)
Over-Current
Protection
Input
Voltage
(V)
Synchronous
Rectifier
Light-Load
Efficiency
Switch
Current
Limit
(mA)
Boost
Features
Number
of
Channels
Package
(mm)
Isolated DC/DC Power Supplies
Isolated Flyback Converter Selection Guide
Input
Voltage
Range
(V)
Switching
Frequency
(kHz)
Control
Mode
Soft Start
Light-Load
Efficiency
UVLO
New BD7F100HFN-LB
New BD7F100EFJ-LB
1W at VIN 5.0V
5W at VIN 24V
45
1.25
3.0 to 40
400
Adaptive
on-time
✔
✔
✔
✔
New BD7F200HFN-LB
New BD7F200EFJ-LB
5W at VIN 12V
10W at VIN 24V
45
2.75
8.0 to 40
400
Adaptive
on-time
✔
✔
✔
✔
☆ BD7J100HFN-LB
☆ BD7J100EFJ-LB
5W at VIN 48V
80
1.0
8.0 to 80
400
Adaptive
on-time
✔
✔
✔
✔
Part No.
Feed
back
Feed
back
-40 to +125
HSON8
HTSOP-J8
Feed
back
Feed
back
-40 to +125
HSON8
HTSOP-J8
Feed
back
Feed
back
-40 to +125
HSON8
HTSOP-J8
33
☆ Under Development
DC/DC Converters Selection Guide
Operating
Junction
Temperature
Range
(℃)
Package
Thermal
Protection
Switch
Current
Limit
(A)
Over-Current
Protection
Output
Power
(W)
Enable
Features
Input
Voltage
Maximum
Rating
(V)
www.rohm.com
Controllers (External Switch FET)
Buck Controller Selection Guide
BD9305AFVM
1
20
Output Voltage
(V)
Switching
Frequency
(MHz)
Control
Mode
4.2～18
-
1.25～VIN *1
0.1～0.8
Voltage
-
-
-
-
-
Latch
Over-Voltage
Protection
Supply
Voltage
(V)
Thermal Protection
Input
Voltage
Range
(V)
Power Good
Part No.
Externally
Synchronizable
Adjustable Soft
Start
Synchronous
Rectifier
Light-Load
Efficiency
Over-Current
Protection
Features
Input
Number
Voltage
of
Maximum
Channels
Rating
(V)
Recove
ry
Description
-
Recove Recove
Latch
Tracking feature
ry
ry
Operating
Temperature
(℃)
Package
-40～+85
MSOP8
-10～+85
VQFN020V4040
BD95601MUV-LB
1
28
4.5～25
4.5～5.5
0.75～2.0
0.2～0.5
H3 Reg
✔
-
✔
✔
✔
BD63536FJ
1
32
3.0～30
-
1.25～VIN *1
0.01～0.3
Voltage
-
-
-
-
-
Recove Recove Recove
ry
ry
ry
-25～+85
SOP-J8
-
-40～+85
SSOP-B14
-
-40～+105
VQFN020V4040
-20～+100
VQFN032V5050
-20～+85
VQFN032V5050
-40～+105
SSOP-B20
BD9845FV
1
36
3.6～35
-
1.0～VIN *1
0.1～1.5
Voltage
-
-
✔
-
-
Recove Recove
ry
ry
BD9611MUV
1
60
10～56
-
1.0～(VIN×0.8)
0.05～0.5
Voltage
-
✔
✔
✔
-
Recove Recove
ry
ry
BD9528AMUV
2
30
5.5～28
-
1.0～5.5
0.2～0.5
H3 Reg
✔
-
✔
✔
✔
Latch
Recove Recove Output discharge,
Latch
ry
ry 3.3V LDO, 5V LDO
BD95602MUV
BD95602MUV-LB
2
30
5.5～28
-
1.0～5.5
0.15～0.5
H3 Reg
✔
-
✔
✔
✔
BD9848FV
2
36
3.6～35
-
1.0～VIN *1
0.1～1.5
Voltage
-
-
✔
-
-
Pre Bias,
Adjustable UVLO
Recove Recove Output discharge,
ry
ry 3.3V LDO, 5V LDO
Recove Recove
ry
ry
-
*1 Restrictions depend on input/output voltage conditions.
Boost/Buck-boost Controller Selection Guide
Description
Operating
Temperature
(℃)
Package
(mm)
BD8303MUV
1
15
2.7～14
1.8～12
200～1000
Voltage
-
✔
-
-
✔
-
✔
Latch
Recove
ry
-25～+85
VQFN016V3030
BD9306AFVM
1
20
4.2～18
VIN～(VIN/0.3)
100～800
Voltage
✔
-
-
-
✔
-
-
Latch
Recove
ry
-40～+85
MSOP8
BD9851EFV
2
20
4.0～18
1.0～*1
10～3000
Voltage
✔
-
✔
✔
-
✔
-
Latch
Recove
ry
-40～+85
HTSSOP-B20
BA9743AFV
2
36
3.6～35
2.505～*1
10～800
Voltage
✔
-
✔
✔
-
✔
-
Latch
Recove
Adjustable Dead Time
ry
-40～+85
SSOP-B16
-40～+85
SSOP-B16
Thermal
Protection
Enable
Control
Mode
Buck
Switching
Frequency
(kHz)
Inverting
Output
Voltage
(V)
Buck-Boost
Input
Voltage
(V)
Boost
Part No.
Adjustable
Soft Start
Synchronous
Rectifier
Short Circuit
Protection
Features
Input
Number
Voltage
of
Maximum
Channels
Rating
(V)
BA9744FV
2
36
2.5～35
1.222～*1
10～800
Voltage
✔
-
✔
✔
-
✔
-
Recove
Latch
Adjustable Dead Time
ry
BA9741F
2
36
3.6～35
2.5～*1
10～800
Voltage
✔
-
✔
✔
-
✔
-
Latch
Recove
Adjustable Dead Time
ry
-40～+85
SOP16
BA9741FS
2
36
3.6～35
2.5～*1
10～800
Voltage
✔
-
✔
✔
-
✔
-
Latch
Recove
Adjustable Dead Time
ry
-40～+85
SSOP-A16
*1 Restrictions depend on input/output voltage conditions.
34
DC/DC Converters Selection Guide
www.rohm.com
Notes
1) The information contained herein is subject to change without notice.
2) Before you use our Products, please contact our sales representative and verify the latest specifications.
3) Although ROHM is continuously working to improve product reliability and quality, semicon- ductors can
break down and malfunction due to various factors. Therefore, in order to prevent personal injury or fire
arising from failure, please take safety measures such as complying with the derating characteristics,
implementing redundant and fire prevention designs, and utilizing backups and fail-safe procedures.
ROHM shall have no responsibility for any damages arising out of the use of our Poducts beyond the
rating specified by ROHM.
4) Examples of application circuits, circuit constants and any other information contained herein are
provided only to illustrate the standard usage and operations of the Products. The peripheral conditions
must be taken into account when designing circuits for mass production.
5) The technical information specified herein is intended only to show the typical functions of and examples
of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to
use or exercise intellectual property or other rights held by ROHM or any other parties. ROHM shall have
no responsibility whatsoever for any dispute arising out of the use of such technical information.
6) The Products are intended for use in general electronic equipment (i.e. AV/OA devices, communi- cation,
consumer systems, gaming/entertainment sets) as well as the applications indicated in this document.
7) The Products specified in this document are not designed to be radiation tolerant.
8) For use of our Products in applications requiring a high degree of reliability (as exemplified below), please
contact and consult with a ROHM representative : transportation equipment (i.e. cars, ships, trains),
primary communication equipment, traffic lights, fire/crime prevention, safety equipment, medical
systems, servers, solar cells, and power transmission systems.
9) Do not use our Products in applications requiring extremely high reliability, such as aerospace equipment,
nuclear power control systems, and submarine repeaters.
10) ROHM shall have no responsibility for any damages or injury arising from non-compliance with the
recommended usage conditions and specifications contained herein.
11) ROHM has used reasonable care to ensure the accuracy of the information contained in this document.
However, ROHM does not warrants that such information is error-free, and ROHM shall have no
responsibility for any damages arising from any inaccuracy or misprint of such information.
12) Please use the Products in accordance with any applicable environmental laws and regulations, such as
the RoHS Directive. For more details, including RoHS compatibility, please contact a ROHM sales office.
ROHM shall have no responsibility for any damages or losses resulting non-compliance with any
applicable laws or regulations.
13) When providing our Products and technologies contained in this document to other countries, you must
abide by the procedures and provisions stipulated in all applicable export laws and regulations, including
without limitation the US Export Administration Regulations and the Foreign Exchange and Foreign Trade
Act.
14) This document, in part or in whole, may not be reprinted or reproduced without prior consent of ROHM.
AEK59-A1-0255 ©2016 ROHM Co., Ltd. All rights reserved.
Application Engineer Div.